From febc2b831f633d8d6648267952bd43c35689c36f Mon Sep 17 00:00:00 2001 From: TruongSinh Tran-Nguyen Date: Wed, 1 Dec 2021 16:18:17 +0100 Subject: [PATCH] ipq40xx: add support for GL.iNet GL-B2200 This patch adds supports for the GL-B2200 router. Specifications: - SOC: Qualcomm IPQ4019 ARM Quad-Core - RAM: 512 MiB - Flash: 16 MiB NOR - SPI0 - EMMC: 8GB EMMC - ETH: Qualcomm QCA8075 - WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11b/g/n 2x2 - WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11n/ac W2 2x2 - WLAN3: Qualcomm Atheros QCA9886 5GHz 802.11n/ac W2 2x2 - INPUT: Reset, WPS - LED: Power, Internet - UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1 - UART2: On board with BLE module - SPI1: On board socket for Zigbee module Update firmware instructions: Please update the firmware via U-Boot web UI (by default at 192.168.1.1, following instructions found at https://docs.gl-inet.com/en/3/troubleshooting/debrick/). Normal sysupgrade, either via CLI or LuCI, is not possible from stock firmware. Please do use the *gl-b2200-squashfs-emmc.img file, gunzipping the produced *gl-b2200-squashfs-emmc.img.gz one first. What's working: - WiFi 2G, 5G - WPA2/WPA3 Not tested: - Bluetooth LE/Zigbee Credits goes to the original authors of this patch. V1->V2: - updates *arm-boot-add-dts-files.patch correctly (sorry, my mistake) - add uboot-envtools support V2->V3: - Li Zhang updated official patch to fix wrong MAC address on wlan0 (PCI) interface V3->V4: - wire up sysupgrade Signed-off-by: Li Zhang [fix tab and trailing space, document what's working and what's not] Signed-off-by: TruongSinh Tran-Nguyen [rebase on top of master, address remaining comments] Signed-off-by: Enrico Mioso [remove redundant check in platform.sh] Signed-off-by: Daniel Golle --- package/boot/uboot-envtools/files/ipq40xx | 1 + package/firmware/ipq-wifi/Makefile | 2 + .../ipq-wifi/board-glinet_gl-b2200.qca4019 | Bin 0 -> 24308 bytes .../ipq-wifi/board-glinet_gl-b2200.qca9888 | Bin 0 -> 12200 bytes .../ipq40xx/base-files/etc/board.d/02_network | 5 + .../etc/hotplug.d/firmware/11-ath10k-caldata | 5 + .../base-files/lib/upgrade/platform.sh | 15 + .../arm/boot/dts/qcom-ipq4019-gl-b2200.dts | 364 ++++++++++++++++++ target/linux/ipq40xx/generic/target.mk | 1 + target/linux/ipq40xx/image/generic.mk | 28 ++ .../901-arm-boot-add-dts-files.patch | 3 +- .../901-arm-boot-add-dts-files.patch | 3 +- 12 files changed, 425 insertions(+), 2 deletions(-) create mode 100644 package/firmware/ipq-wifi/board-glinet_gl-b2200.qca4019 create mode 100644 package/firmware/ipq-wifi/board-glinet_gl-b2200.qca9888 create mode 100644 target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-gl-b2200.dts diff --git a/package/boot/uboot-envtools/files/ipq40xx b/package/boot/uboot-envtools/files/ipq40xx index 1462aa991d7d..9a71a622f7ba 100644 --- a/package/boot/uboot-envtools/files/ipq40xx +++ b/package/boot/uboot-envtools/files/ipq40xx @@ -35,6 +35,7 @@ devolo,magic-2-wifi-next|\ edgecore,ecw5211|\ glinet,gl-ap1300|\ glinet,gl-b1300|\ +glinet,gl-b2200|\ luma,wrtq-329acn|\ netgear,wac510|\ openmesh,a42|\ diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile index ebaac48c24e7..b1e6541e6143 100644 --- a/package/firmware/ipq-wifi/Makefile +++ b/package/firmware/ipq-wifi/Makefile @@ -39,6 +39,7 @@ ALLWIFIBOARDS:= \ engenius_emr3500 \ ezviz_cs-w3-wd1200g-eup \ glinet_gl-ap1300 \ + glinet_gl-b2200 \ glinet_gl-s1300 \ linksys_ea8300 \ linksys_mr8300-v0 \ @@ -127,6 +128,7 @@ $(eval $(call generate-ipq-wifi-package,engenius_emd1,EnGenius EMD1)) $(eval $(call generate-ipq-wifi-package,engenius_emr3500,EnGenius EMR3500)) $(eval $(call generate-ipq-wifi-package,ezviz_cs-w3-wd1200g-eup,EZVIZ CS-W3-WD1200G EUP)) $(eval $(call generate-ipq-wifi-package,glinet_gl-ap1300,GL.iNet GL-AP1300)) +$(eval $(call generate-ipq-wifi-package,glinet_gl-b2200,GL.iNet GL-B2200)) $(eval $(call generate-ipq-wifi-package,glinet_gl-s1300,GL.iNet GL-S1300)) $(eval $(call generate-ipq-wifi-package,linksys_ea8300,Linksys EA8300)) $(eval $(call generate-ipq-wifi-package,linksys_mr8300-v0,Linksys MR8300)) diff --git a/package/firmware/ipq-wifi/board-glinet_gl-b2200.qca4019 b/package/firmware/ipq-wifi/board-glinet_gl-b2200.qca4019 new file mode 100644 index 0000000000000000000000000000000000000000..ac1850160aead29cee0fb96664272b8a620a4e6a GIT binary patch literal 24308 zcmeHPdr(tX8b1jj>SE!BfCzXAAv{7MK%g2V@)iT6U{R3(i$E30tx+C^hoKAYC{l=s zKrI*|Xc?48Q$)ta7qM7dJEP40v48CBA8ltJ-I;aQcCLna&8 z!7IvLW4{*NNZ>gXcuZf@TlE@SlXXWzx%bckIO$*H5j;jxpDANrJ>r>8pthc<;p4LO zFWA5$8ub~IVOWb{+S}XP+1c3`2mp8RnOZ0=(9STq!n$Fyu$yT!M<~;kWv-Mo58=y3 zFS92zKBQ`@KA4@FEEvD0YO9uI?@5jyA5fiYER(*Kyk&e4YUR?5{LMj?5?%CBs)V8s(0|89p6i8)lgnyGW#&)FdGlkwUvO9>6tCB*50Oq%E*KM znVzW=ZDqAdGTwfd_&Woook^zx%G~lh2Xi_jPqE6K3;G%hEf#BgWOCc@)op9#CSQ*(U<$A9iqn9D?N&D zd{WUJQtMUXoWHzKqM{`cu(MzHs|}8bv&+U!9-GMze1j7IjD3;7e&7WWp3&)a8lKzO zz^~;sda=J!mlf*v;N4w(l*93Xf4*#QZy&Zdo1JO9*65mq42dci5rM3%j5Ide3y$#9 zPfx#}n!>Mu1YBPqUE6=Y|KoRtZMflP2Yb4$?SG-2BRpX<{?DF0d91Tt#BhnOONQX} z2-Heyn}_g(HwNk@0E!<6m!+u@6EMmU6hY$9I3x@WLrUbwYfpU8+}1Hy0Ybgpwn|~3 z3?Abl193;)dG2B-)CqAzLJ7AJ5MqAYB8xAy;bH_T?yBu)Eq2X0u)LVN@ftCmWCN% zW;L%$lx877RVV}~1SkY31SkY31XeKu8~Ga%FUC&(P9&YNmA@5|n9X@vQ|*#8Nv;`dUIZ;@o28=pz7NS*7e5 zePmn)2Et#z;m_Y}7NxC343^MRG#N@PK!Edi+&TclfFI=NctJK02U4NfFyUnjBMh+F zo}O$YX@~7|TiNW~HVzO9XyC`A0JPg9wAcs$0@flx2!yuzYY;$pp|8({rIQn}>1Z-0 zs&Qo?@O;>TNv9uxI}mVpnQpuGBPbW4kh2?uGM_ea7W{DS8U4y!>F?*u`6ZKX=T5g* zr`w$q@7j}fu3VRmH6Zpu#f%1WCzRL& z6~{M_yP(AWr&t2%#T-SbSPG4E5%*=*4 z#Y8+&PoAfk2@}IPk=i8%*p@)w5ZokIH&UTvl4#4&2*3$4z^6d==!vB}SKo)@K z&tx(Io=92ejOc4le(mMx=UJ z)_+R_RUA4P7@~v0AL!uGm<@O$v;~fLY(dO+JAk;@*x4^k2vjc=0u%zP4uKiIyeYo@ zzyJQ1Z@>BG4-gd{2OsC#KmX_7{`C0qUtya$zP(Tw5vt?sPfh*nhlS_ho8sFC=>@0V z{%PC%wZYteIj?HY3Jaebb2 zdtY%@@$8!mqnfGri(%W>BieR#g(6cD^7Rd^N?oJKlL)le)#ntYk|cqzc0|*wRA3T; zC;mTTx9|D~0O-)BmMiv3c$34Lv&y4bhD4wlRrg?+Bux;c{jIuHA(O-lSh&NT34eb; zm|==cMdsv9O_x%R?UroS+*F>!%0!6*K6GeP93~ycC;Yi!^0wxJvI6$|hIUx#$=*6LCEAS%_U_uwol-$bKv^n zb7)l`R~9MK;K2*ZDr}b|1P0QnkV{ep+{x>j^U5+TUBtm1KAYe|l&)zz)#b`OMdIWb zJXo&C#Zq9H7a^9h0u&zYQdeRLqD_RueK-eeWC>pCQz2P$0x6Uzl*}No5|)OUsZq_V z7J-hDBbQ^^gBv_5E^2p5CtTIkZu7apc(L__mM+ z5BbP&kviq<>%Z|hdZs6{IqWzKb4>f9|8Q$;ov&v5ZvHi@mj&aaOKCb%>gwViXUCGcs6ZW0I4wZZ)#3f}jUx#aa} zq}_>USaKx4f3RFFJjpI~l8knjH7C>r$y_rYe45e}RK2OlXLaF;Yqsv+6CLIpF0Lgw_mqlW0-)SYN8M@iNGAX{WBvoOUWJ!ZD$n5 zYOB7CZ%;g92LFwkO=%Pc|NnJB^6dQ}i>4P+hd2%}K^9CbIDB>~+0r mM)B=m6*pJ+8D3jzj85S3pID+VNxf)UhC)x=qn z6hu*pVibldri{aMtZm0Sj1_0p=|dl!=}RB_?1Ob2UrKs6Vfj-usnGhfXLI+Sd+zzp zx%b-*>~hH8log+)lqX6R@v?1M1)IVC{rdqFCV@QzPzqZ`lQylsvL;Sft*NSONK0H# zR>oCT>uM^i)1=aM>*KUd71|bUWA*;{aSth!Db@*JXw{WB)Rb!))3#FaGJ=pw1u%X% z%oU#S=Pv>Qy0)m>61;co}D5`;0|G zrw9as1)Kmd^eeq_&X2&(G_r%bSc@y(%(tB^-zrKYuYc763JujWw?DUMyU=@NZ~a3?E)0zRZR9 z@ez*W_v|Sta@j&c{QX@q=ki=XSZ^AH0qYN&2HD2Oj+-K}v3N9wv4(d~dle4|h9Fs3 z7Ltf1BK1uN4}WDeb#}k3fYfpM(IW-LPzm|~MMAI;NeJbK`60_O877m+9>|bvEL)OI zWn!6#93wD7LOdXlWGq>dOi3{*LShq(u-aa&POK?4bz)V#`qK4rhZ29x|A{{miiJu- zsZH3XCz}ujrjRJ8BrNGk5|V06|0y6Uj6d=aMfccj0WC8dF zeII>B)dB&r%yqh5RYxjtDPz-{>7#NbDRTmF7GR@Ks5E2_PB2$#GlVLauYnq)(vo@j zI_q`)N&1j{`#2y*j05X{-lS5?Rd^iJPa7eW!V_T-Bg_DU*oPPsU8ho#NfS%5_A+L= zo;6v&(HrPyxq?iFK@9Xk`8G1me#zRdSJNeOi4zbbjs;d5(@7s-0n8=6iEfkUkm>fT z3`1*Fg(PwNvh^6#NGs*IYY$>Eun#g8IGIOEVFn}JBF`o_+WVN}bPa2JG-&^tsikvN zgbNUh1A9MQQUi>ZXuYCuhZ%Col-o9|QC~~%mXnYA>_&#B6)LF{5R1pW=`u~5=U-Q* z(J{+_XK5B*)9xX?TG%hR75 z@Y>*=pJbowDK*OUE6M{3u3gl25<09B&A)y|(IVL!R_L?wO3%J_NnO}3KgBJZ#{AjQ z@M@9rl8rv4I1!}@+Sz56>k{^cDSeWM&K+WswNVuTd0iJuPG%emt3`|FAj;>UT zRQ+9A;|5LSu0U$Uw$m727q%P8869e|=9&^(eU&}ERpyj7aXqTM*R3^B%@I2S6sOLq z3~2|U-?owKx$O!1P&Ha|-d5h3d^q|5qC8~EZ(FrHFvlnT?D;AtQ@=(NQ270gmdgpp zutvWM>xF7dYO7d-<}t>dEqG~Aw(rIhUB$=ACcMT!?}x!JtkPDj7Ts~DztWt3B&Go^ zywYCRCM{o)i=+&n)fsd3L@m12+_le`bug9=R=tK=eu`&+XW$)YVA0|w%Y1wh|A3(2 z(CP1GuF=~rf5=cq`i-{c5!mY0QSh@WG9r9cL_}mn5%6Lwqv5!e%#`O9m#OQUj~Fc7 zy#qrxe;yqj<<|1H`Q5<>5kbgGbStqH*@kW)HXs?O7bl>gqQiD$Wa^oF_4llQImZ%C z<}8Ohd*yw223Q83KY#x0*|Wc<$P8ZG`g=9R%(dT)WqfQys#MJkKLh~w%}np`!#|}cLng@-_Ag}1cmds3FU2UT%7sp zsbcuUwRiabY`r*ob=3daT$MXltZ{VzhQmBEeggR@Wl+3_YL7nwaiZE~$P|r!674hM-``+9JAJ#(MsTt=M z?b>5HeWBm}-R*m`=^qv=le-a(iI6ZXOcF+kz~-^d2!&A+irNg;j;%#fu~bPawRX +#include +#include + +/ { + model = "GL.iNet GL-B2200"; + compatible = "glinet,gl-b2200", "qcom,ipq4019"; + + memory { + device_type = "memory"; + reg = <0x80000000 0x10000000>; + }; + + chosen { + bootargs-append = " root=/dev/mmcblk0p2 rw rootwait clk_ignore_unused"; + }; + + soc { + rng@22000 { + status = "okay"; + }; + + mdio@90000 { + status = "okay"; + }; + + ess-psgmii@98000 { + status = "okay"; + }; + + tcsr@1949000 { + compatible = "qcom,tcsr"; + reg = <0x1949000 0x100>; + qcom,wifi_glb_cfg = ; + }; + + tcsr@194b000 { + /* select hostmode */ + compatible = "qcom,tcsr"; + reg = <0x194b000 0x100>; + qcom,usb-hsphy-mode-select = ; + status = "okay"; + }; + + ess_tcsr@1953000 { + compatible = "qcom,tcsr"; + reg = <0x1953000 0x1000>; + qcom,ess-interface-select = ; + }; + + tcsr@1957000 { + compatible = "qcom,tcsr"; + reg = <0x1957000 0x100>; + qcom,wifi_noc_memtype_m0_m2 = ; + }; + + crypto@8e3a000 { + status = "okay"; + }; + + ess-switch@c000000 { + status = "okay"; + switch_lan_bmp = <0x2e>; + switch_wan_bmp = <0x10>; + }; + + edma@c080000 { + status = "okay"; + }; + }; + + keys { + compatible = "gpio-keys"; + + wps { + label = "wps"; + gpios = <&tlmm 18 GPIO_ACTIVE_LOW>; + linux,code = ; + linux,input-type = <1>; + }; + + reset { + label = "reset"; + gpios = <&tlmm 43 GPIO_ACTIVE_LOW>; + linux,code = ; + linux,input-type = <1>; + }; + }; + + leds { + compatible = "gpio-leds"; + + power_blue { + label = "blue:power"; + gpios = <&tlmm 57 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + internet_blue { + label = "blue:internet"; + gpios = <&tlmm 60 GPIO_ACTIVE_HIGH>; + }; + power_white { + label = "white:power"; + gpios = <&tlmm 61 GPIO_ACTIVE_LOW>; + }; + internet_white { + label = "white:internet"; + gpios = <&tlmm 66 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&gmac1 { + qcom,phy_mdio_addr = <3>; + qcom,poll_required = <1>; + qcom,forced_speed = <1000>; + qcom,forced_duplex = <1>; + vlan_tag = <2 0x10>; +}; + +&gmac0 { + vlan_tag = <1 0x2e>; +}; + +&vqmmc { + status = "okay"; +}; + +&sdhci { + status = "okay"; + pinctrl-0 = <&sd_pins>; + pinctrl-names = "default"; + cd-gpios = <&tlmm 3 GPIO_ACTIVE_LOW>; + vqmmc-supply = <&vqmmc>; +}; + +&blsp_dma { + status = "okay"; +}; + +&cryptobam { + status = "okay"; +}; + +&blsp1_spi1 { + pinctrl-0 = <&spi_0_pins>; + pinctrl-names = "default"; + status = "okay"; + cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <24000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "SBL1"; + reg = <0x0 0x40000>; + read-only; + }; + + partition@40000 { + label = "MIBIB"; + reg = <0x40000 0x20000>; + read-only; + }; + + partition@60000 { + label = "QSEE"; + reg = <0x60000 0x60000>; + read-only; + }; + + partition@c0000 { + label = "CDT"; + reg = <0xc0000 0x10000>; + read-only; + }; + + partition@d0000 { + label = "DDRPARAMS"; + reg = <0xd0000 0x10000>; + read-only; + }; + + partition@e0000 { + label = "APPSBLENV"; + reg = <0xe0000 0x10000>; + read-only; + }; + + partition@f0000 { + label = "APPSBL"; + reg = <0xf0000 0x80000>; + read-only; + }; + + partition@170000 { + label = "ART"; + reg = <0x170000 0x10000>; + read-only; + }; + }; + }; +}; + +&blsp1_spi2 { + pinctrl-0 = <&spi_1_pins>; + pinctrl-names = "default"; + status = "okay"; + + spidev1: spi@0 { + compatible = "siliconlabs,si3210"; + reg = <0>; + spi-max-frequency = <24000000>; + }; +}; + +&blsp1_uart1 { + pinctrl-0 = <&serial_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&blsp1_uart2 { + pinctrl-0 = <&serial_1_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&tlmm { + serial_pins: serial_pinmux { + mux { + pins = "gpio16", "gpio17"; + function = "blsp_uart0"; + bias-disable; + }; + }; + + serial_1_pins: serial1_pinmux { + mux { + pins = "gpio8", "gpio9", + "gpio10", "gpio11"; + function = "blsp_uart1"; + bias-disable; + }; + }; + + spi_0_pins: spi_0_pinmux { + pinmux { + function = "blsp_spi0"; + pins = "gpio13", "gpio14", "gpio15"; + }; + pinmux_cs { + function = "gpio"; + pins = "gpio12"; + }; + pinconf { + pins = "gpio13", "gpio14", "gpio15"; + drive-strength = <12>; + bias-disable; + }; + pinconf_cs { + pins = "gpio12"; + drive-strength = <2>; + bias-disable; + output-high; + }; + }; + + spi_1_pins: spi_1_pinmux { + mux { + pins = "gpio44", "gpio46", "gpio47"; + function = "blsp_spi1"; + bias-disable; + }; + cs { + pins = "gpio45"; + function = "gpio"; + bias-pull-up; + }; + reset { + pins = "gpio43"; + function = "gpio"; + output-high; + }; + mux_2 { + pins = "gpio35"; + function = "gpio"; + output-high; + }; + host_int { + pins = "gpio2"; + function = "gpio"; + input; + }; + wake { + pins = "gpio48"; + function = "gpio"; + output-high; + }; + }; + + sd_pins: sd_pins { + pinmux { + function = "sdio"; + pins = "gpio23", "gpio24", "gpio25", "gpio26", + "gpio29", "gpio30", "gpio31", "gpio32"; + drive-strength = <10>; + }; + + pinmux_sd_clk { + function = "sdio"; + pins = "gpio27"; + drive-strength = <16>; + }; + + pinmux_sd7 { + function = "sdio"; + pins = "gpio28"; + drive-strength = <10>; + bias-disable; + }; + }; + +}; + +&pcie0 { + status = "okay"; + perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>; + wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>; + + bridge@0,0 { + reg = <0x00000000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + ranges; + + wifi2: wifi@1,0 { + status = "okay"; + compatible = "qcom,ath10k"; + reg = <0x00010000 0 0 0 0>; + qcom,ath10k-calibration-variant = "GL-B2200"; + }; + }; +}; + +&wifi0 { + status = "okay"; + qcom,ath10k-calibration-variant = "GL-B2200"; +}; + +&wifi1 { + status = "okay"; + qcom,ath10k-calibration-variant = "GL-B2200"; +}; diff --git a/target/linux/ipq40xx/generic/target.mk b/target/linux/ipq40xx/generic/target.mk index f5cb1fb19b94..e158b1c98b10 100644 --- a/target/linux/ipq40xx/generic/target.mk +++ b/target/linux/ipq40xx/generic/target.mk @@ -1 +1,2 @@ BOARDNAME:=Generic +FEATURES+=emmc diff --git a/target/linux/ipq40xx/image/generic.mk b/target/linux/ipq40xx/image/generic.mk index 0d7d7a30d223..872c4f957f32 100644 --- a/target/linux/ipq40xx/image/generic.mk +++ b/target/linux/ipq40xx/image/generic.mk @@ -92,6 +92,16 @@ define Build/qsdk-ipq-factory-nand-askey @mv $@.new $@ endef +define Build/qsdk-ipq-app-gpt + cp $@ $@.tmp 2>/dev/null || true + ptgen -g -o $@.tmp -a 1 -l 1024 \ + -t 0x2e -N 0:HLOS -r -p 32M \ + -t 0x83 -N rootfs -r -p 128M \ + -N rootfs_data -p 512M + cat $@.tmp >> $@ + rm $@.tmp +endef + define Build/SenaoFW -$(STAGING_DIR_HOST)/bin/mksenaofw \ -n $(BOARD_NAME) -r $(VENDOR_ID) -p $(1) \ @@ -520,6 +530,24 @@ define Device/glinet_gl-b1300 endef TARGET_DEVICES += glinet_gl-b1300 +define Device/glinet_gl-b2200 + $(call Device/FitzImage) + DEVICE_VENDOR := GL.iNet + DEVICE_MODEL := GL-B2200 + SOC := qcom-ipq4019 + DEVICE_DTS_CONFIG := config@ap.dk04.1-c3 + KERNEL_INITRAMFS_SUFFIX := -recovery.itb + IMAGES := emmc.img.gz sysupgrade.bin + IMAGE/emmc.img.gz := qsdk-ipq-app-gpt |\ + pad-to 1024k | append-kernel |\ + pad-to 33792k | append-rootfs |\ + append-metadata | gzip + IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata + DEVICE_PACKAGES := ath10k-firmware-qca9888-ct ipq-wifi-glinet_gl-b2200 \ + kmod-fs-ext4 kmod-mmc kmod-spi-dev mkf2fs e2fsprogs kmod-fs-f2fs +endef +TARGET_DEVICES += glinet_gl-b2200 + define Device/glinet_gl-s1300 $(call Device/FitzImage) DEVICE_VENDOR := GL.iNet diff --git a/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch index 3bd13bf93219..b641251423fa 100644 --- a/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -902,11 +902,70 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -902,11 +902,71 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ @@ -76,6 +76,7 @@ Signed-off-by: John Crispin + qcom-ipq4029-ap-303h.dtb \ + qcom-ipq4029-ap-365.dtb \ + qcom-ipq4029-gl-b1300.dtb \ ++ qcom-ipq4019-gl-b2200.dtb \ + qcom-ipq4029-gl-s1300.dtb \ + qcom-ipq4029-mr33.dtb \ qcom-ipq8064-ap148.dtb \ diff --git a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch index 734d08387a42..4270418d6c2b 100644 --- a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -837,11 +837,68 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -837,11 +837,69 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ @@ -74,6 +74,7 @@ Signed-off-by: John Crispin + qcom-ipq4029-ap-303h.dtb \ + qcom-ipq4029-ap-365.dtb \ + qcom-ipq4029-gl-b1300.dtb \ ++ qcom-ipq4019-gl-b2200.dtb \ + qcom-ipq4029-gl-s1300.dtb \ + qcom-ipq4029-mr33.dtb \ qcom-ipq8064-ap148.dtb \ -- 2.30.2