From fde68cb80941a60be93ece75e808b5b407d11cc8 Mon Sep 17 00:00:00 2001 From: Chukun Pan Date: Mon, 18 Oct 2021 12:20:03 +0800 Subject: [PATCH] sunxi: add support for FriendlyARM NanoPi R1S H5 Specification: CPU: Allwinner H5, Quad-core Cortex-A53 DDR3 RAM: 512MB Network: 10/100/1000M Ethernet x 2 USB Host: Type-A x 1 MicroSD Slot x 1 MicroUSB: for power input Debug Serial Port: 3Pin pin-header LED: WAN, LAN, SYS KEY: Reset Power Supply: DC 5V/2A Installation: Write the image to SD Card with dd. Note: 1. OpenWrt currently does not support LED_FUNCTION, change back to the previous practice (Consistent with NanoPi R1). 2. Since the upstream commit https://github.com/torvalds/linux/bbc4d71 ("net: phy: realtek: fix rtl8211e rx/tx delay config"), we need to change the phy-mode from rgmii to rgmii-id. So set phy-mode for 5.4 and 5.10 respectively. Signed-off-by: Chukun Pan --- .../sunxi/base-files/etc/board.d/01_leds | 3 +- .../sunxi/base-files/etc/board.d/02_network | 63 +++-- target/linux/sunxi/cortexa53/config-5.10 | 1 + target/linux/sunxi/cortexa53/config-5.4 | 1 + target/linux/sunxi/image/cortexa53.mk | 9 + ...nxi-h5-add-support-for-nanopi-r1s-h5.patch | 230 ++++++++++++++++++ ...lwinner-nanopi-r1s-h5-add-status-LED.patch | 35 +++ ...nxi-h5-add-support-for-nanopi-r1s-h5.patch | 229 +++++++++++++++++ ...lwinner-nanopi-r1s-h5-add-status-LED.patch | 35 +++ 9 files changed, 587 insertions(+), 19 deletions(-) create mode 100644 target/linux/sunxi/patches-5.10/101-sunxi-h5-add-support-for-nanopi-r1s-h5.patch create mode 100644 target/linux/sunxi/patches-5.10/431-arm64-dts-allwinner-nanopi-r1s-h5-add-status-LED.patch create mode 100644 target/linux/sunxi/patches-5.4/101-sunxi-h5-add-support-for-nanopi-r1s-h5.patch create mode 100644 target/linux/sunxi/patches-5.4/431-arm64-dts-allwinner-nanopi-r1s-h5-add-status-LED.patch diff --git a/target/linux/sunxi/base-files/etc/board.d/01_leds b/target/linux/sunxi/base-files/etc/board.d/01_leds index 45153b44dc..60783363de 100644 --- a/target/linux/sunxi/base-files/etc/board.d/01_leds +++ b/target/linux/sunxi/base-files/etc/board.d/01_leds @@ -7,7 +7,8 @@ boardname="${board##*,}" board_config_update case $board in -friendlyarm,nanopi-r1) +friendlyarm,nanopi-r1|\ +friendlyarm,nanopi-r1s-h5) ucidef_set_led_netdev "wan" "WAN" "nanopi:green:wan" "eth0" ucidef_set_led_netdev "lan" "LAN" "nanopi:green:lan" "eth1" ;; diff --git a/target/linux/sunxi/base-files/etc/board.d/02_network b/target/linux/sunxi/base-files/etc/board.d/02_network index d5c615e7f2..46ace1f67c 100644 --- a/target/linux/sunxi/base-files/etc/board.d/02_network +++ b/target/linux/sunxi/base-files/etc/board.d/02_network @@ -3,27 +3,54 @@ # . /lib/functions/uci-defaults.sh +. /lib/functions/system.sh -board_config_update +sunxi_setup_interfaces() +{ + local board="$1" + + case "$board" in + friendlyarm,nanopi-r1|\ + friendlyarm,nanopi-r1s-h5) + ucidef_set_interfaces_lan_wan "eth1" "eth0" + ;; + lamobo,lamobo-r1) + ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" wan + ;; + olimex,a20-olinuxino-micro) + ucidef_set_interface_lan "wlan0" + ;; + xunlong,orangepi-r1) + ucidef_set_interfaces_lan_wan "eth0" "eth1" + ;; + *) + ucidef_set_interface_lan "eth0" + ;; + esac +} + +sunxi_setup_macs() +{ + local board="$1" + local lan_mac="" + local wan_mac="" + local label_mac="" -case $(board_name) in -friendlyarm,nanopi-r1) - ucidef_set_interfaces_lan_wan "eth1" "eth0" - ;; -lamobo,lamobo-r1) - ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" wan - ;; -olimex,a20-olinuxino-micro) - ucidef_set_interface_lan "wlan0" - ;; -xunlong,orangepi-r1) - ucidef_set_interfaces_lan_wan "eth0" "eth1" - ;; -*) - ucidef_set_interface_lan "eth0" - ;; -esac + case "$board" in + friendlyarm,nanopi-r1s-h5) + lan_mac=$(get_mac_binary "/sys/bus/i2c/devices/0-0051/eeprom" 0xfa) + ;; + esac + [ -n "$lan_mac" ] && ucidef_set_interface_macaddr "lan" $lan_mac + [ -n "$wan_mac" ] && ucidef_set_interface_macaddr "wan" $wan_mac + [ -n "$label_mac" ] && ucidef_set_label_macaddr $label_mac +} + +board_config_update +board=$(board_name) +sunxi_setup_interfaces $board +sunxi_setup_macs $board board_config_flush exit 0 diff --git a/target/linux/sunxi/cortexa53/config-5.10 b/target/linux/sunxi/cortexa53/config-5.10 index f5f0ab066d..f2586949ce 100644 --- a/target/linux/sunxi/cortexa53/config-5.10 +++ b/target/linux/sunxi/cortexa53/config-5.10 @@ -26,6 +26,7 @@ CONFIG_AUDIT_ARCH_COMPAT_GENERIC=y CONFIG_CC_HAVE_STACKPROTECTOR_SYSREG=y CONFIG_DMA_DIRECT_REMAP=y CONFIG_DWMAC_SUN8I=y +CONFIG_EEPROM_AT24=y # CONFIG_FLATMEM_MANUAL is not set CONFIG_FRAME_POINTER=y CONFIG_GENERIC_BUG_RELATIVE_POINTERS=y diff --git a/target/linux/sunxi/cortexa53/config-5.4 b/target/linux/sunxi/cortexa53/config-5.4 index b0f92faf23..aa19a41622 100644 --- a/target/linux/sunxi/cortexa53/config-5.4 +++ b/target/linux/sunxi/cortexa53/config-5.4 @@ -69,6 +69,7 @@ CONFIG_AUDIT_ARCH_COMPAT_GENERIC=y CONFIG_DMA_DIRECT_REMAP=y CONFIG_DRM_RCAR_WRITEBACK=y CONFIG_DWMAC_SUN8I=y +CONFIG_EEPROM_AT24=y CONFIG_EFI_EARLYCON=y # CONFIG_FLATMEM_MANUAL is not set CONFIG_FRAME_POINTER=y diff --git a/target/linux/sunxi/image/cortexa53.mk b/target/linux/sunxi/image/cortexa53.mk index 2d18b0b227..c88aee2d7c 100644 --- a/target/linux/sunxi/image/cortexa53.mk +++ b/target/linux/sunxi/image/cortexa53.mk @@ -40,6 +40,15 @@ define Device/friendlyarm_nanopi-neo2 endef TARGET_DEVICES += friendlyarm_nanopi-neo2 +define Device/friendlyarm_nanopi-r1s-h5 + DEVICE_VENDOR := FriendlyARM + DEVICE_MODEL := Nanopi R1S H5 + DEVICE_PACKAGES := kmod-gpio-button-hotplug kmod-usb-net-rtl8152 + SUPPORTED_DEVICES:=nanopi-r1s-h5 + $(Device/sun50i-h5) +endef +TARGET_DEVICES += friendlyarm_nanopi-r1s-h5 + define Device/libretech_all-h3-cc-h5 DEVICE_VENDOR := Libre Computer DEVICE_MODEL := ALL-H3-CC diff --git a/target/linux/sunxi/patches-5.10/101-sunxi-h5-add-support-for-nanopi-r1s-h5.patch b/target/linux/sunxi/patches-5.10/101-sunxi-h5-add-support-for-nanopi-r1s-h5.patch new file mode 100644 index 0000000000..e0c25bcb53 --- /dev/null +++ b/target/linux/sunxi/patches-5.10/101-sunxi-h5-add-support-for-nanopi-r1s-h5.patch @@ -0,0 +1,230 @@ +From 9962cb9be2db877c232aaf00db40125c0d7bf4bc Mon Sep 17 00:00:00 2001 +From: Chukun Pan +Date: Mon, 17 May 2021 00:35:22 +0800 +Subject: [PATCH] arm64: dts: allwinner: h5: Add NanoPi R1S H5 support + +The NanoPi R1S H5 is a open source board made by FriendlyElec. +It has the following features: + +- Allwinner H5, Quad-core Cortex-A53 +- 512MB DDR3 RAM +- 10/100/1000M Ethernet x 2 +- RTL8189ETV WiFi 802.11b/g/n +- USB 2.0 host port (A) +- MicroSD Slot +- Serial Debug Port +- 5V 2A DC power-supply + +Signed-off-by: Chukun Pan +Signed-off-by: Maxime Ripard +Link: https://lore.kernel.org/r/20210516163523.9484-2-amadeus@jmu.edu.cn +--- + arch/arm64/boot/dts/allwinner/Makefile | 1 + + .../dts/allwinner/sun50i-h5-nanopi-r1s-h5.dts | 195 ++++++++++++++++++ + 2 files changed, 196 insertions(+) + create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-r1s-h5.dts + +--- a/arch/arm64/boot/dts/allwinner/Makefile ++++ b/arch/arm64/boot/dts/allwinner/Makefile +@@ -24,6 +24,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-li + dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-libretech-all-h5-cc.dtb + dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-nanopi-neo2.dtb + dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-nanopi-neo-plus2.dtb ++dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-nanopi-r1s-h5.dtb + dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb + dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-prime.dtb + dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus.dtb +--- /dev/null ++++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-r1s-h5.dts +@@ -0,0 +1,191 @@ ++// SPDX-License-Identifier: (GPL-2.0+ OR MIT) ++/* ++ * Copyright (C) 2021 Chukun Pan ++ * ++ * Based on sun50i-h5-nanopi-neo-plus2.dts, which is: ++ * Copyright (C) 2017 Antony Antony ++ * Copyright (C) 2016 ARM Ltd. ++ */ ++ ++/dts-v1/; ++#include "sun50i-h5.dtsi" ++#include "sun50i-h5-cpu-opp.dtsi" ++ ++#include ++#include ++ ++/ { ++ model = "FriendlyARM NanoPi R1S H5"; ++ compatible = "friendlyarm,nanopi-r1s-h5", "allwinner,sun50i-h5"; ++ ++ aliases { ++ ethernet0 = &emac; ++ ethernet1 = &rtl8189etv; ++ serial0 = &uart0; ++ }; ++ ++ chosen { ++ stdout-path = "serial0:115200n8"; ++ }; ++ ++ leds { ++ compatible = "gpio-leds"; ++ ++ sys { ++ label = "nanopi:red:sys"; ++ gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>; ++ linux,default-trigger = "heartbeat"; ++ }; ++ ++ lan { ++ label = "nanopi:green:lan"; ++ gpios = <&pio 0 9 GPIO_ACTIVE_HIGH>; ++ }; ++ ++ wan { ++ label = "nanopi:green:wan"; ++ gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>; ++ }; ++ }; ++ ++ r-gpio-keys { ++ compatible = "gpio-keys"; ++ ++ reset { ++ label = "reset"; ++ linux,code = ; ++ gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>; ++ }; ++ }; ++ ++ reg_gmac_3v3: gmac-3v3 { ++ compatible = "regulator-fixed"; ++ regulator-name = "gmac-3v3"; ++ regulator-min-microvolt = <3300000>; ++ regulator-max-microvolt = <3300000>; ++ startup-delay-us = <100000>; ++ enable-active-high; ++ gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; ++ }; ++ ++ reg_vcc3v3: vcc3v3 { ++ compatible = "regulator-fixed"; ++ regulator-name = "vcc3v3"; ++ regulator-min-microvolt = <3300000>; ++ regulator-max-microvolt = <3300000>; ++ }; ++ ++ reg_usb0_vbus: usb0-vbus { ++ compatible = "regulator-fixed"; ++ regulator-name = "usb0-vbus"; ++ regulator-min-microvolt = <5000000>; ++ regulator-max-microvolt = <5000000>; ++ enable-active-high; ++ gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */ ++ status = "okay"; ++ }; ++ ++ vdd_cpux: gpio-regulator { ++ compatible = "regulator-gpio"; ++ regulator-name = "vdd-cpux"; ++ regulator-type = "voltage"; ++ regulator-boot-on; ++ regulator-always-on; ++ regulator-min-microvolt = <1100000>; ++ regulator-max-microvolt = <1300000>; ++ regulator-ramp-delay = <50>; /* 4ms */ ++ gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; ++ gpios-states = <0x1>; ++ states = <1100000 0x0>, <1300000 0x1>; ++ }; ++ ++ wifi_pwrseq: wifi_pwrseq { ++ compatible = "mmc-pwrseq-simple"; ++ reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */ ++ post-power-on-delay-ms = <200>; ++ }; ++}; ++ ++&cpu0 { ++ cpu-supply = <&vdd_cpux>; ++}; ++ ++&ehci1 { ++ status = "okay"; ++}; ++ ++&ehci2 { ++ status = "okay"; ++}; ++ ++&emac { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&emac_rgmii_pins>; ++ phy-supply = <®_gmac_3v3>; ++ phy-handle = <&ext_rgmii_phy>; ++ phy-mode = "rgmii-id"; ++ status = "okay"; ++}; ++ ++&external_mdio { ++ ext_rgmii_phy: ethernet-phy@7 { ++ compatible = "ethernet-phy-ieee802.3-c22"; ++ reg = <7>; ++ }; ++}; ++ ++&i2c0 { ++ status = "okay"; ++ ++ eeprom@51 { ++ compatible = "microchip,24c02"; ++ reg = <0x51>; ++ pagesize = <16>; ++ }; ++}; ++ ++&mmc0 { ++ vmmc-supply = <®_vcc3v3>; ++ bus-width = <4>; ++ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ ++ status = "okay"; ++}; ++ ++&mmc1 { ++ vmmc-supply = <®_vcc3v3>; ++ vqmmc-supply = <®_vcc3v3>; ++ mmc-pwrseq = <&wifi_pwrseq>; ++ bus-width = <4>; ++ non-removable; ++ status = "okay"; ++ ++ rtl8189etv: sdio_wifi@1 { ++ reg = <1>; ++ }; ++}; ++ ++&ohci1 { ++ status = "okay"; ++}; ++ ++&ohci2 { ++ status = "okay"; ++}; ++ ++&uart0 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&uart0_pa_pins>; ++ status = "okay"; ++}; ++ ++&usb_otg { ++ dr_mode = "peripheral"; ++ status = "okay"; ++}; ++ ++&usbphy { ++ /* USB Type-A port's VBUS is always on */ ++ usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */ ++ usb0_vbus-supply = <®_usb0_vbus>; ++ status = "okay"; ++}; diff --git a/target/linux/sunxi/patches-5.10/431-arm64-dts-allwinner-nanopi-r1s-h5-add-status-LED.patch b/target/linux/sunxi/patches-5.10/431-arm64-dts-allwinner-nanopi-r1s-h5-add-status-LED.patch new file mode 100644 index 0000000000..4a429c746e --- /dev/null +++ b/target/linux/sunxi/patches-5.10/431-arm64-dts-allwinner-nanopi-r1s-h5-add-status-LED.patch @@ -0,0 +1,35 @@ +From 1845163a052efac124f00656eb72f38947630a42 Mon Sep 17 00:00:00 2001 +From: Chukun Pan +Date: Sun, 10 Oct 2021 21:50:18 +0800 +Subject: [PATCH] arm64: dts: allwinner: NanoPi R1S H5: add status LED aliases + +Use the SYS LED on the casing for showing system status. + +Signed-off-by: Chukun Pan +--- + arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-r1s-h5.dts | 7 ++++++- + 1 file changed, 6 insertions(+), 1 deletion(-) + +--- a/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-r1s-h5.dts ++++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-r1s-h5.dts +@@ -22,6 +22,11 @@ + ethernet0 = &emac; + ethernet1 = &rtl8189etv; + serial0 = &uart0; ++ ++ led-boot = &led_sys; ++ led-failsafe = &led_sys; ++ led-running = &led_sys; ++ led-upgrade = &led_sys; + }; + + chosen { +@@ -31,7 +36,7 @@ + leds { + compatible = "gpio-leds"; + +- sys { ++ led_sys: sys { + label = "nanopi:red:sys"; + gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; diff --git a/target/linux/sunxi/patches-5.4/101-sunxi-h5-add-support-for-nanopi-r1s-h5.patch b/target/linux/sunxi/patches-5.4/101-sunxi-h5-add-support-for-nanopi-r1s-h5.patch new file mode 100644 index 0000000000..339eadcd23 --- /dev/null +++ b/target/linux/sunxi/patches-5.4/101-sunxi-h5-add-support-for-nanopi-r1s-h5.patch @@ -0,0 +1,229 @@ +From 9962cb9be2db877c232aaf00db40125c0d7bf4bc Mon Sep 17 00:00:00 2001 +From: Chukun Pan +Date: Mon, 17 May 2021 00:35:22 +0800 +Subject: [PATCH] arm64: dts: allwinner: h5: Add NanoPi R1S H5 support + +The NanoPi R1S H5 is a open source board made by FriendlyElec. +It has the following features: + +- Allwinner H5, Quad-core Cortex-A53 +- 512MB DDR3 RAM +- 10/100/1000M Ethernet x 2 +- RTL8189ETV WiFi 802.11b/g/n +- USB 2.0 host port (A) +- MicroSD Slot +- Serial Debug Port +- 5V 2A DC power-supply + +Signed-off-by: Chukun Pan +Signed-off-by: Maxime Ripard +Link: https://lore.kernel.org/r/20210516163523.9484-2-amadeus@jmu.edu.cn +--- + arch/arm64/boot/dts/allwinner/Makefile | 1 + + .../dts/allwinner/sun50i-h5-nanopi-r1s-h5.dts | 195 ++++++++++++++++++ + 2 files changed, 196 insertions(+) + create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-r1s-h5.dts + +--- a/arch/arm64/boot/dts/allwinner/Makefile ++++ b/arch/arm64/boot/dts/allwinner/Makefile +@@ -17,6 +17,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-em + dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-libretech-all-h3-cc.dtb + dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-nanopi-neo2.dtb + dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-nanopi-neo-plus2.dtb ++dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-nanopi-r1s-h5.dtb + dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb + dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-prime.dtb + dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus.dtb +--- /dev/null ++++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-r1s-h5.dts +@@ -0,0 +1,190 @@ ++// SPDX-License-Identifier: (GPL-2.0+ OR MIT) ++/* ++ * Copyright (C) 2021 Chukun Pan ++ * ++ * Based on sun50i-h5-nanopi-neo-plus2.dts, which is: ++ * Copyright (C) 2017 Antony Antony ++ * Copyright (C) 2016 ARM Ltd. ++ */ ++ ++/dts-v1/; ++#include "sun50i-h5.dtsi" ++ ++#include ++#include ++ ++/ { ++ model = "FriendlyARM NanoPi R1S H5"; ++ compatible = "friendlyarm,nanopi-r1s-h5", "allwinner,sun50i-h5"; ++ ++ aliases { ++ ethernet0 = &emac; ++ ethernet1 = &rtl8189etv; ++ serial0 = &uart0; ++ }; ++ ++ chosen { ++ stdout-path = "serial0:115200n8"; ++ }; ++ ++ leds { ++ compatible = "gpio-leds"; ++ ++ sys { ++ label = "nanopi:red:sys"; ++ gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>; ++ linux,default-trigger = "heartbeat"; ++ }; ++ ++ lan { ++ label = "nanopi:green:lan"; ++ gpios = <&pio 0 9 GPIO_ACTIVE_HIGH>; ++ }; ++ ++ wan { ++ label = "nanopi:green:wan"; ++ gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>; ++ }; ++ }; ++ ++ r-gpio-keys { ++ compatible = "gpio-keys"; ++ ++ reset { ++ label = "reset"; ++ linux,code = ; ++ gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>; ++ }; ++ }; ++ ++ reg_gmac_3v3: gmac-3v3 { ++ compatible = "regulator-fixed"; ++ regulator-name = "gmac-3v3"; ++ regulator-min-microvolt = <3300000>; ++ regulator-max-microvolt = <3300000>; ++ startup-delay-us = <100000>; ++ enable-active-high; ++ gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; ++ }; ++ ++ reg_vcc3v3: vcc3v3 { ++ compatible = "regulator-fixed"; ++ regulator-name = "vcc3v3"; ++ regulator-min-microvolt = <3300000>; ++ regulator-max-microvolt = <3300000>; ++ }; ++ ++ reg_usb0_vbus: usb0-vbus { ++ compatible = "regulator-fixed"; ++ regulator-name = "usb0-vbus"; ++ regulator-min-microvolt = <5000000>; ++ regulator-max-microvolt = <5000000>; ++ enable-active-high; ++ gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */ ++ status = "okay"; ++ }; ++ ++ vdd_cpux: gpio-regulator { ++ compatible = "regulator-gpio"; ++ regulator-name = "vdd-cpux"; ++ regulator-type = "voltage"; ++ regulator-boot-on; ++ regulator-always-on; ++ regulator-min-microvolt = <1100000>; ++ regulator-max-microvolt = <1300000>; ++ regulator-ramp-delay = <50>; /* 4ms */ ++ gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; ++ gpios-states = <0x1>; ++ states = <1100000 0x0>, <1300000 0x1>; ++ }; ++ ++ wifi_pwrseq: wifi_pwrseq { ++ compatible = "mmc-pwrseq-simple"; ++ reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */ ++ post-power-on-delay-ms = <200>; ++ }; ++}; ++ ++&cpu0 { ++ cpu-supply = <&vdd_cpux>; ++}; ++ ++&ehci1 { ++ status = "okay"; ++}; ++ ++&ehci2 { ++ status = "okay"; ++}; ++ ++&emac { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&emac_rgmii_pins>; ++ phy-supply = <®_gmac_3v3>; ++ phy-handle = <&ext_rgmii_phy>; ++ phy-mode = "rgmii"; ++ status = "okay"; ++}; ++ ++&external_mdio { ++ ext_rgmii_phy: ethernet-phy@7 { ++ compatible = "ethernet-phy-ieee802.3-c22"; ++ reg = <7>; ++ }; ++}; ++ ++&i2c0 { ++ status = "okay"; ++ ++ eeprom@51 { ++ compatible = "microchip,24c02"; ++ reg = <0x51>; ++ pagesize = <16>; ++ }; ++}; ++ ++&mmc0 { ++ vmmc-supply = <®_vcc3v3>; ++ bus-width = <4>; ++ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ ++ status = "okay"; ++}; ++ ++&mmc1 { ++ vmmc-supply = <®_vcc3v3>; ++ vqmmc-supply = <®_vcc3v3>; ++ mmc-pwrseq = <&wifi_pwrseq>; ++ bus-width = <4>; ++ non-removable; ++ status = "okay"; ++ ++ rtl8189etv: sdio_wifi@1 { ++ reg = <1>; ++ }; ++}; ++ ++&ohci1 { ++ status = "okay"; ++}; ++ ++&ohci2 { ++ status = "okay"; ++}; ++ ++&uart0 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&uart0_pa_pins>; ++ status = "okay"; ++}; ++ ++&usb_otg { ++ dr_mode = "peripheral"; ++ status = "okay"; ++}; ++ ++&usbphy { ++ /* USB Type-A port's VBUS is always on */ ++ usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */ ++ usb0_vbus-supply = <®_usb0_vbus>; ++ status = "okay"; ++}; diff --git a/target/linux/sunxi/patches-5.4/431-arm64-dts-allwinner-nanopi-r1s-h5-add-status-LED.patch b/target/linux/sunxi/patches-5.4/431-arm64-dts-allwinner-nanopi-r1s-h5-add-status-LED.patch new file mode 100644 index 0000000000..8281f78e06 --- /dev/null +++ b/target/linux/sunxi/patches-5.4/431-arm64-dts-allwinner-nanopi-r1s-h5-add-status-LED.patch @@ -0,0 +1,35 @@ +From 1845163a052efac124f00656eb72f38947630a42 Mon Sep 17 00:00:00 2001 +From: Chukun Pan +Date: Sun, 10 Oct 2021 21:50:18 +0800 +Subject: [PATCH] arm64: dts: allwinner: NanoPi R1S H5: add status LED aliases + +Use the SYS LED on the casing for showing system status. + +Signed-off-by: Chukun Pan +--- + arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-r1s-h5.dts | 7 ++++++- + 1 file changed, 6 insertions(+), 1 deletion(-) + +--- a/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-r1s-h5.dts ++++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-r1s-h5.dts +@@ -21,6 +21,11 @@ + ethernet0 = &emac; + ethernet1 = &rtl8189etv; + serial0 = &uart0; ++ ++ led-boot = &led_sys; ++ led-failsafe = &led_sys; ++ led-running = &led_sys; ++ led-upgrade = &led_sys; + }; + + chosen { +@@ -30,7 +35,7 @@ + leds { + compatible = "gpio-leds"; + +- sys { ++ led_sys: sys { + label = "nanopi:red:sys"; + gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; -- 2.30.2