From f87a780f07b22b6dc4642dbaf44af65112076cb8 Mon Sep 17 00:00:00 2001 From: Chris Wilson Date: Fri, 11 Dec 2015 11:32:58 +0000 Subject: [PATCH] drm/i915: Limit the busy wait on requests to 5us not 10ms! When waiting for high frequency requests, the finite amount of time required to set up the irq and wait upon it limits the response rate. By busywaiting on the request completion for a short while we can service the high frequency waits as quick as possible. However, if it is a slow request, we want to sleep as quickly as possible. The tradeoff between waiting and sleeping is roughly the time it takes to sleep on a request, on the order of a microsecond. Based on measurements of synchronous workloads from across big core and little atom, I have set the limit for busywaiting as 10 microseconds. In most of the synchronous cases, we can reduce the limit down to as little as 2 miscroseconds, but that leaves quite a few test cases regressing by factors of 3 and more. The code currently uses the jiffie clock, but that is far too coarse (on the order of 10 milliseconds) and results in poor interactivity as the CPU ends up being hogged by slow requests. To get microsecond resolution we need to use a high resolution timer. The cheapest of which is polling local_clock(), but that is only valid on the same CPU. If we switch CPUs because the task was preempted, we can also use that as an indicator that the system is too busy to waste cycles on spinning and we should sleep instead. __i915_spin_request was introduced in commit 2def4ad99befa25775dd2f714fdd4d92faec6e34 [v4.2] Author: Chris Wilson Date: Tue Apr 7 16:20:41 2015 +0100 drm/i915: Optimistically spin for the request completion v2: Drop full u64 for unsigned long - the timer is 32bit wraparound safe, so we can use native register sizes on smaller architectures. Mention the approximate microseconds units for elapsed time and add some extra comments describing the reason for busywaiting. v3: Raise the limit to 10us v4: Now 5us. Reported-by: Jens Axboe Link: https://lkml.org/lkml/2015/11/12/621 Reviewed-by: Tvrtko Ursulin Cc: "Rogozhkin, Dmitry V" Cc: Daniel Vetter Cc: Tvrtko Ursulin Cc: Eero Tamminen Cc: "Rantala, Valtteri" Cc: stable@vger.kernel.org Signed-off-by: Daniel Vetter Link: http://patchwork.freedesktop.org/patch/msgid/1449833608-22125-3-git-send-email-chris@chris-wilson.co.uk (cherry picked from commit ca5b721e238226af1d767103ac852aeb8e4c0764) Signed-off-by: Jani Nikula --- drivers/gpu/drm/i915/i915_gem.c | 47 +++++++++++++++++++++++++++++++-- 1 file changed, 45 insertions(+), 2 deletions(-) diff --git a/drivers/gpu/drm/i915/i915_gem.c b/drivers/gpu/drm/i915/i915_gem.c index 06631e130efc..8719fa2ae7e7 100644 --- a/drivers/gpu/drm/i915/i915_gem.c +++ b/drivers/gpu/drm/i915/i915_gem.c @@ -1146,14 +1146,57 @@ static bool missed_irq(struct drm_i915_private *dev_priv, return test_bit(ring->id, &dev_priv->gpu_error.missed_irq_rings); } +static unsigned long local_clock_us(unsigned *cpu) +{ + unsigned long t; + + /* Cheaply and approximately convert from nanoseconds to microseconds. + * The result and subsequent calculations are also defined in the same + * approximate microseconds units. The principal source of timing + * error here is from the simple truncation. + * + * Note that local_clock() is only defined wrt to the current CPU; + * the comparisons are no longer valid if we switch CPUs. Instead of + * blocking preemption for the entire busywait, we can detect the CPU + * switch and use that as indicator of system load and a reason to + * stop busywaiting, see busywait_stop(). + */ + *cpu = get_cpu(); + t = local_clock() >> 10; + put_cpu(); + + return t; +} + +static bool busywait_stop(unsigned long timeout, unsigned cpu) +{ + unsigned this_cpu; + + if (time_after(local_clock_us(&this_cpu), timeout)) + return true; + + return this_cpu != cpu; +} + static int __i915_spin_request(struct drm_i915_gem_request *req, int state) { unsigned long timeout; + unsigned cpu; + + /* When waiting for high frequency requests, e.g. during synchronous + * rendering split between the CPU and GPU, the finite amount of time + * required to set up the irq and wait upon it limits the response + * rate. By busywaiting on the request completion for a short while we + * can service the high frequency waits as quick as possible. However, + * if it is a slow request, we want to sleep as quickly as possible. + * The tradeoff between waiting and sleeping is roughly the time it + * takes to sleep on a request, on the order of a microsecond. + */ if (i915_gem_request_get_ring(req)->irq_refcount) return -EBUSY; - timeout = jiffies + 1; + timeout = local_clock_us(&cpu) + 5; while (!need_resched()) { if (i915_gem_request_completed(req, true)) return 0; @@ -1161,7 +1204,7 @@ static int __i915_spin_request(struct drm_i915_gem_request *req, int state) if (signal_pending_state(state, current)) break; - if (time_after_eq(jiffies, timeout)) + if (busywait_stop(timeout, cpu)) break; cpu_relax_lowlatency(); -- 2.30.2