From f7f8099aa3ae551df14b3b2bac332a80e861a690 Mon Sep 17 00:00:00 2001 From: Tomasz Maciej Nowak Date: Wed, 17 Apr 2024 17:01:55 +0200 Subject: [PATCH] ath79: add support for Dell SonicPoint ACe APL26-0AE Dell/SonicWall APL26-0AE (marketed as SonicPoint ACe) is a dual band wireless access point. End of life as of 2022-07-31. Specification SoC: QualcommAtheros QCA9550 RAM: 256 MB DDR2 Flash: 32 MB SPI NOR WIFI: 2.4 GHz 3T3R integrated 5 GHz 3T3R QCA9890 oversized Mini PCIe card Ethernet: 2x 10/100/1000 Mbps QCA8334 port labeled lan1 is PoE capable (802.3at) USB: 1x 2.0 LEDs: LEDs: 6x which 5 are GPIO controlled and two of them are dual color Buttons: 2x GPIO controlled Serial: RJ-45 port, SonicWall pinout baud: 115200, parity: none, flow control: none Before flashing, be sure to have a copy of factory firmware, in case You wish to revert to original firmware. All described procedures were done in following environment: ROM Version: SonicROM (U-Boot) 8.0.0.0-11o SafeMode Firmware Version: SonicOS 8.0.0.0-14o Firmware Version: SonicOS 9.0.1.0 In case of other versions, following installation instructions might be ineffective. Installation 1. Prepare TFTP server with OpenWrt sysupgrade image and rename that image to "sp_fw.bin". 2. Connect to one of LAN ports. 3. Connect to serial port. 4. Hold the reset button (small through hole on side of the unit), power on the device and when prompted to stop autoboot, hit any key. The held button can now be released. 5. Alter U-Boot environment with following commands: setenv bootcmd bootm 0x9F110000 saveenv 6. Adjust "ipaddr" (access point, default is 192.168.1.1) and "serverip" (TFTP server, default is 192.168.1.10) addresses in U-Boot environment, then run following commands: tftp 0x80060000 sp_fw.bin erase 0x9F110000 +0x1EF0000 cp.b 0x80060000 0x9F110000 $filesize 7. After successful flashing, execute: boot 8. The access point will boot to OpenWrt. Wait few minutes, until the wrench LED will stop blinking, then it's ready for configuration. Known issues Initramfs image can't be bigger than specified kernel size, otherwise bootloader will throw LZMA decompressing error. Switching to lzma-loader should workaround that. This device has Winbond 25Q256FVFG and doesn't have reliable reset, which causes hang on reboot, thus broken-flash-reset needs to be added. This property addition causes dispaly of "scary" warning on each boot, take this warnig into consideration. Signed-off-by: Tomasz Maciej Nowak --- package/boot/uboot-envtools/files/ath79 | 3 + .../ath79/dts/qca9550_dell_apl26-0ae.dts | 228 ++++++++++++++++++ .../generic/base-files/etc/board.d/01_leds | 4 + .../generic/base-files/etc/board.d/02_network | 4 + target/linux/ath79/image/generic.mk | 16 ++ 5 files changed, 255 insertions(+) create mode 100644 target/linux/ath79/dts/qca9550_dell_apl26-0ae.dts diff --git a/package/boot/uboot-envtools/files/ath79 b/package/boot/uboot-envtools/files/ath79 index 4a6e7e4d0a..099aebcfa2 100644 --- a/package/boot/uboot-envtools/files/ath79 +++ b/package/boot/uboot-envtools/files/ath79 @@ -109,6 +109,9 @@ buffalo,wzr-hp-g300nh-s|\ linksys,ea4500-v3) ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x20000" "0x20000" ;; +dell,apl26-0ae) + ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x40000" "0x10000" + ;; domywifi,dw33d) ubootenv_add_uci_config "/dev/mtd4" "0x0" "0x10000" "0x10000" ;; diff --git a/target/linux/ath79/dts/qca9550_dell_apl26-0ae.dts b/target/linux/ath79/dts/qca9550_dell_apl26-0ae.dts new file mode 100644 index 0000000000..6ef2eb846d --- /dev/null +++ b/target/linux/ath79/dts/qca9550_dell_apl26-0ae.dts @@ -0,0 +1,228 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include +#include +#include + +#include "qca955x.dtsi" + +/ { + model = "Dell SonicPoint ACe (APL26-0AE)"; + compatible = "dell,apl26-0ae", "qca,qca9550", "qca,qca9558"; + + aliases { + label-mac-device = ð0; + led-boot = &led_wrench; + led-failsafe = &led_wrench; + led-upgrade = &led_wrench; + }; + + keys { + compatible = "gpio-keys"; + + button-reset { + label = "reset"; + gpios = <&gpio 21 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + /* Accessible only after disassembling the casing */ + button-service { + label = "service"; + gpios = <&gpio 22 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&jtag_disable_pins>; + + led-lan1-amber { + color = ; + function = LED_FUNCTION_LAN; + function-enumerator = <1>; + gpios = <&gpio 13 GPIO_ACTIVE_LOW>; + }; + + led-lan1-green { + color = ; + function = LED_FUNCTION_LAN; + function-enumerator = <1>; + gpios = <&gpio 3 GPIO_ACTIVE_LOW>; + }; + + led-lan2-amber { + color = ; + function = LED_FUNCTION_LAN; + function-enumerator = <2>; + gpios = <&gpio 17 GPIO_ACTIVE_LOW>; + }; + + led-lan2-green { + color = ; + function = LED_FUNCTION_LAN; + function-enumerator = <2>; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + }; + + led-wlan2g { + color = ; + function = LED_FUNCTION_WLAN_2GHZ; + linux,default-trigger = "phy1tpt"; + gpios = <&gpio 1 GPIO_ACTIVE_LOW>; + }; + + led-wlan5g { + color = ; + function = LED_FUNCTION_WLAN_5GHZ; + linux,default-trigger = "phy0tpt"; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + }; + + led_wrench: led-wrench { + color = ; + function = LED_FUNCTION_STATUS; + gpios = <&gpio 0 GPIO_ACTIVE_LOW>; + }; + }; +}; + +ð0 { + status = "okay"; + + nvmem-cells = <&macaddr_sysinfo_50 0>; + nvmem-cell-names = "mac-address"; + phy-handle = <&phy0>; + pll-data = <0xa6000000 0x00000101 0x00001616>; +}; + +ð1 { + status = "okay"; + + nvmem-cells = <&macaddr_sysinfo_50 1>; + nvmem-cell-names = "mac-address"; + pll-data = <0x03000101 0x00000101 0x00001616>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&mdio0 { + status = "okay"; + + phy0: ethernet-phy@0 { + reg = <0>; + + qca,ar8327-initvals = < + 0x04 0x07680000 /* PORT0 PAD MODE CTRL */ + 0x0c 0x00000080 /* PORT6 PAD MODE CTRL */ + 0x10 0x40000000 /* POWER_ON_STRAP */ + 0x50 0xffb7c405 /* LED0 CTRL */ + 0x54 0xffb7c305 /* LED1 CTRL */ + 0x58 0xffb7c033 /* LED2 CTRL */ + 0x5c 0x03ffff00 /* LED3 CTRL */ + 0x7c 0x0000007e /* PORT0_STATUS */ + 0x94 0x0000007e /* PORT6_STATUS */ + >; + }; +}; + +&pcie0 { + status = "okay"; + + wifi@0,0 { + compatible = "qcom,ath10k"; + reg = <0x0000 0 0 0 0>; + + /* OEM overwrites EEPROM stored adress and so do we */ + nvmem-cells = <&macaddr_sysinfo_50 2>; + nvmem-cell-names = "mac-address"; + }; +}; + +&spi { + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <25000000>; + broken-flash-reset; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0000000 0x0080000>; + read-only; + }; + + partition@80000 { + label = "u-boot-env"; + reg = <0x0080000 0x0040000>; + }; + + partition@c0000 { + label = "sysinfo"; + reg = <0x00c0000 0x0040000>; + read-only; + + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_sysinfo_50: macaddr@50 { + compatible = "mac-base"; + reg = <0x50 0x6>; + #nvmem-cell-cells = <1>; + }; + }; + }; + + partition@100000 { + label = "art"; + reg = <0x0100000 0x0010000>; + read-only; + + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + cal_art_1000: calibration@1000 { + reg = <0x1000 0x440>; + }; + }; + }; + + partition@110000 { + label = "firmware"; + reg = <0x0110000 0x1ef0000>; + compatible = "denx,uimage"; + }; + }; + }; +}; + +&usb_phy0 { + status = "okay"; +}; + +&usb0 { + status = "okay"; +}; + +&wmac { + status = "okay"; + + nvmem-cells = <&macaddr_sysinfo_50 10>, <&cal_art_1000>; + nvmem-cell-names = "mac-address", "calibration"; +}; diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds index 98d1b0a7ba..143309a8b2 100644 --- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds +++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds @@ -232,6 +232,10 @@ compex,wpj531-16m) ucidef_set_led_rssi "sig3" "SIG3" "green:sig3" "wlan0" "65" "100" ucidef_set_led_rssi "sig4" "SIG4" "green:sig4" "wlan0" "50" "100" ;; +dell,apl26-0ae) + ucidef_set_led_switch "lan1" "LAN1" "amber:lan-1" "switch0" "0x04" + ucidef_set_led_switch "lan2" "LAN2" "amber:lan-2" "switch0" "0x08" + ;; devolo,dlan-pro-1200plus-ac|\ devolo,magic-2-wifi) ucidef_set_led_netdev "plcw" "dLAN" "white:dlan" "eth0.1" "rx" diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network index 8af618d267..7905d6e496 100644 --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network @@ -288,6 +288,10 @@ ath79_setup_interfaces() ucidef_add_switch "switch0" \ "1:wan" "5:lan" "6@eth0" ;; + dell,apl26-0ae) + ucidef_add_switch "switch0" \ + "0@eth0" "2:lan:1" "3:lan:2" "6@eth1" + ;; devolo,dlan-pro-1200plus-ac|\ devolo,magic-2-wifi) ucidef_add_switch "switch0" \ diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk index ca72c8c6d8..0da5a0ef8d 100644 --- a/target/linux/ath79/image/generic.mk +++ b/target/linux/ath79/image/generic.mk @@ -944,6 +944,22 @@ define Device/compex_wpj563 endef TARGET_DEVICES += compex_wpj563 +define Device/dell_apl26-0ae + SOC := qca9550 + DEVICE_VENDOR := Dell + DEVICE_MODEL := SonicPoint + DEVICE_VARIANT := ACe (APL26-0AE) + DEVICE_ALT0_VENDOR := SonicWall + DEVICE_ALT0_MODEL := SonicPoint + DEVICE_ALT0_VARIANT := ACe (APL26-0AE) + DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct kmod-usb2 + KERNEL_SIZE := 5952k + IMAGE_SIZE := 31680k + IMAGE/sysupgrade.bin = append-kernel | pad-to $$$$(BLOCKSIZE) | \ + append-rootfs | pad-rootfs | check-size | append-metadata +endef +TARGET_DEVICES += dell_apl26-0ae + define Device/devolo_dlan-pro-1200plus-ac SOC := ar9344 DEVICE_VENDOR := devolo -- 2.30.2