From f5cc52873111dfc6f48a914b2ad1493e2422a68a Mon Sep 17 00:00:00 2001 From: Zoltan HERPAI Date: Tue, 16 Oct 2018 16:25:29 +0200 Subject: [PATCH] riscv64: backport various patches Signed-off-by: Zoltan HERPAI --- target/linux/riscv64/config-4.19 | 63 +- .../0009-RISC-V-Networking-fix-Hack.patch | 39 + ...dded-support-for-the-Vera-board-root.patch | 804 ++++++++++++ .../riscv64/patches/002-clk-sifive-prci.patch | 509 ++++++++ .../riscv64/patches/003-clk-gemgxl.patch | 196 +++ .../riscv64/patches/004-spi-sifive.patch | 509 ++++++++ .../riscv64/patches/005-spi-is25wp256d.patch | 110 ++ .../006-uart-sifive-serial-driver.patch | 1128 +++++++++++++++++ ...o-sifive-support-GPIO-on-SiFive-SoCs.patch | 409 ++++++ 9 files changed, 3717 insertions(+), 50 deletions(-) create mode 100644 target/linux/riscv64/patches/0009-RISC-V-Networking-fix-Hack.patch create mode 100644 target/linux/riscv64/patches/0010-pcie-microsemi-added-support-for-the-Vera-board-root.patch create mode 100644 target/linux/riscv64/patches/002-clk-sifive-prci.patch create mode 100644 target/linux/riscv64/patches/003-clk-gemgxl.patch create mode 100644 target/linux/riscv64/patches/004-spi-sifive.patch create mode 100644 target/linux/riscv64/patches/005-spi-is25wp256d.patch create mode 100644 target/linux/riscv64/patches/006-uart-sifive-serial-driver.patch create mode 100644 target/linux/riscv64/patches/007-gpio-sifive-support-GPIO-on-SiFive-SoCs.patch diff --git a/target/linux/riscv64/config-4.19 b/target/linux/riscv64/config-4.19 index f6a13e8c30..afb2b850c0 100644 --- a/target/linux/riscv64/config-4.19 +++ b/target/linux/riscv64/config-4.19 @@ -4,29 +4,29 @@ CONFIG_ARCH_HAS_PTE_SPECIAL=y # CONFIG_ARCH_RV32I is not set CONFIG_ARCH_RV64I=y CONFIG_ARCH_WANT_FRAME_POINTERS=y -# CONFIG_ASIX_PHY is not set CONFIG_ASN1=y CONFIG_ASSOCIATIVE_ARRAY=y CONFIG_ASYMMETRIC_KEY_TYPE=y CONFIG_ASYMMETRIC_PUBLIC_KEY_SUBTYPE=y CONFIG_ATA=y CONFIG_ATA_VERBOSE_ERROR=y -# CONFIG_ATH5K_PCI is not set -# CONFIG_AUTOFS_FS is not set CONFIG_BLK_DEV_SD=y CONFIG_BLK_MQ_PCI=y CONFIG_BLK_MQ_VIRTIO=y CONFIG_BLK_SCSI_REQUEST=y -# CONFIG_BPFILTER is not set CONFIG_CAVIUM_PTP=y CONFIG_CC_HAS_SANCOV_TRACE_PC=y CONFIG_CC_HAS_STACKPROTECTOR_NONE=y CONFIG_CC_IS_GCC=y +CONFIG_CC_OPTIMIZE_FOR_PERFORMANCE=y +# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_CLANG_VERSION=0 CONFIG_CLKDEV_LOOKUP=y +CONFIG_CLK_GEMGXL_MGMT=y +CONFIG_CLK_U54_PRCI=y CONFIG_CLONE_BACKWARDS=y CONFIG_CLZ_TAB=y -CONFIG_CMDLINE="earlyprintk root=/dev/mmcblk0p2 rootwait" +CONFIG_CMDLINE="earlyprintk root=/dev/mmcblk0p2 rootwait console=ttySI0" CONFIG_CMDLINE_BOOL=y CONFIG_CMODEL_MEDANY=y # CONFIG_CMODEL_MEDLOW is not set @@ -42,15 +42,10 @@ CONFIG_CRC16=y CONFIG_CRC32_SLICEBY8=y CONFIG_CRC7=y CONFIG_CRC_ITU_T=y -CONFIG_CRYPTO_ACOMP2=y CONFIG_CRYPTO_AEAD=y CONFIG_CRYPTO_AEAD2=y -# CONFIG_CRYPTO_AEGIS128 is not set -# CONFIG_CRYPTO_AEGIS128L is not set -# CONFIG_CRYPTO_AEGIS256 is not set CONFIG_CRYPTO_AKCIPHER=y CONFIG_CRYPTO_AKCIPHER2=y -# CONFIG_CRYPTO_CFB is not set CONFIG_CRYPTO_CRC32C=y CONFIG_CRYPTO_DRBG=y CONFIG_CRYPTO_DRBG_HMAC=y @@ -61,11 +56,8 @@ CONFIG_CRYPTO_HASH2=y CONFIG_CRYPTO_HASH_INFO=y CONFIG_CRYPTO_HMAC=y CONFIG_CRYPTO_JITTERENTROPY=y -CONFIG_CRYPTO_KPP2=y CONFIG_CRYPTO_MANAGER=y CONFIG_CRYPTO_MANAGER2=y -# CONFIG_CRYPTO_MORUS1280 is not set -# CONFIG_CRYPTO_MORUS640 is not set CONFIG_CRYPTO_NULL=y CONFIG_CRYPTO_NULL2=y CONFIG_CRYPTO_RNG=y @@ -73,11 +65,7 @@ CONFIG_CRYPTO_RNG2=y CONFIG_CRYPTO_RNG_DEFAULT=y CONFIG_CRYPTO_RSA=y CONFIG_CRYPTO_SHA256=y -# CONFIG_CRYPTO_SM3 is not set -# CONFIG_CRYPTO_SM4 is not set -# CONFIG_CRYPTO_SPECK is not set CONFIG_CRYPTO_WORKQUEUE=y -# CONFIG_CRYPTO_ZSTD is not set CONFIG_DEBUG_BUGVERBOSE=y # CONFIG_DEBUG_FS is not set CONFIG_DEBUG_SECTION_MISMATCH=y @@ -88,14 +76,11 @@ CONFIG_DEVTMPFS=y CONFIG_DEVTMPFS_MOUNT=y CONFIG_DMA_DIRECT_OPS=y CONFIG_DNOTIFY=y -# CONFIG_DP83822_PHY is not set -# CONFIG_DP83TC811_PHY is not set CONFIG_DTC=y CONFIG_E1000E=y CONFIG_EARLY_PRINTK=y CONFIG_ELF_CORE=y CONFIG_ENABLE_MUST_CHECK=y -CONFIG_EXPORTFS=y CONFIG_EXT3_FS=y # CONFIG_EXT3_FS_POSIX_ACL is not set # CONFIG_EXT3_FS_SECURITY is not set @@ -107,8 +92,7 @@ CONFIG_FRAME_POINTER=y CONFIG_FRAME_WARN=2048 CONFIG_FS_IOMAP=y CONFIG_FS_MBCACHE=y -CONFIG_FUTEX_PI=y -CONFIG_GCC_VERSION=80100 +CONFIG_GCC_VERSION=80200 # CONFIG_GEMINI_ETHERNET is not set CONFIG_GENERIC_BUG=y CONFIG_GENERIC_BUG_RELATIVE_POINTERS=y @@ -127,9 +111,7 @@ CONFIG_GPIOLIB=y CONFIG_GPIOLIB_FASTPATH_LIMIT=512 # CONFIG_GPIO_HLWD is not set # CONFIG_GPIO_MAX3191X is not set -# CONFIG_GPIO_MB86S7X is not set -# CONFIG_GPIO_PCIE_IDIO_24 is not set -# CONFIG_GUP_BENCHMARK is not set +CONFIG_GPIO_SIFIVE=y CONFIG_HAS_DMA=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT_MAP=y @@ -178,8 +160,6 @@ CONFIG_KEYS=y # CONFIG_LAN743X is not set # CONFIG_LEDS_CR0014114 is not set # CONFIG_LEDS_LM3692X is not set -# CONFIG_LEDS_MLXREG is not set -# CONFIG_LEDS_TRIGGER_ACTIVITY is not set CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 CONFIG_LIBFDT=y @@ -192,11 +172,8 @@ CONFIG_MAXPHYSMEM_128GB=y # CONFIG_MAXPHYSMEM_2GB is not set CONFIG_MDIO_BUS=y CONFIG_MDIO_DEVICE=y -# CONFIG_MDIO_MSCC_MIIM is not set CONFIG_MEMFD_CREATE=y -# CONFIG_MICROCHIP_T1_PHY is not set CONFIG_MICROSEMI_PHY=y -# CONFIG_MISC_RTSX_PCI is not set # CONFIG_MISC_RTSX_USB is not set CONFIG_MMC=y CONFIG_MMC_BLOCK=y @@ -217,9 +194,8 @@ CONFIG_NEED_DMA_MAP_STATE=y CONFIG_NET_FAILOVER=y CONFIG_NET_FLOW_LIMIT=y CONFIG_NET_NS=y -CONFIG_NET_PACKET_ENGINE=y CONFIG_NET_PTP_CLASSIFY=y -# CONFIG_NET_SCH_CBS is not set +CONFIG_NET_VENDOR_CADENCE=y CONFIG_NET_VENDOR_CORTINA=y CONFIG_NET_VENDOR_MICROSEMI=y CONFIG_NET_VENDOR_NI=y @@ -239,12 +215,12 @@ CONFIG_OF_MDIO=y CONFIG_OF_NET=y CONFIG_OID_REGISTRY=y CONFIG_OVERLAY_FS_REDIRECT_ALWAYS_FOLLOW=y -# CONFIG_OVERLAY_FS_XINO_AUTO is not set CONFIG_PADATA=y CONFIG_PAGE_OFFSET=0xffffffe000000000 CONFIG_PANIC_TIMEOUT=0 CONFIG_PCI=y # CONFIG_PCIE_CADENCE_HOST is not set +CONFIG_PCIE_MICROSEMI=y CONFIG_PCI_DEBUG=y CONFIG_PCI_DOMAINS=y CONFIG_PCI_DOMAINS_GENERIC=y @@ -267,58 +243,49 @@ CONFIG_RCU_NEED_SEGCBLIST=y CONFIG_RCU_STALL_COMMON=y CONFIG_RCU_TRACE=y CONFIG_RD_GZIP=y +CONFIG_REALTEK_PHY=y CONFIG_REGMAP=y CONFIG_REGMAP_I2C=y CONFIG_REGMAP_SPI=y -# CONFIG_RENESAS_PHY is not set -CONFIG_RFKILL_LEDS=y CONFIG_RFS_ACCEL=y CONFIG_RISCV=y -CONFIG_RISCV_INTC=y CONFIG_RISCV_ISA_A=y CONFIG_RISCV_ISA_C=y -CONFIG_RISCV_PLIC=y CONFIG_RISCV_TIMER=y -# CONFIG_RPMSG_VIRTIO is not set CONFIG_RPS=y CONFIG_RTC_CLASS=y # CONFIG_RTC_DRV_ISL12026 is not set -# CONFIG_RTC_DRV_PCF85363 is not set CONFIG_RTC_I2C_AND_SPI=y -# CONFIG_RUNTIME_TESTING_MENU is not set CONFIG_SATA_AHCI=y CONFIG_SATA_MOBILE_LPM_POLICY=0 CONFIG_SATA_PMP=y CONFIG_SATA_SIL24=y CONFIG_SCHED_DEBUG=y CONFIG_SCSI=y -# CONFIG_SECONDARY_TRUSTED_KEYRING is not set CONFIG_SERIAL_8250_DEPRECATED_OPTIONS=y CONFIG_SERIAL_8250_NR_UARTS=4 CONFIG_SERIAL_8250_RUNTIME_UARTS=4 CONFIG_SERIAL_OF_PLATFORM=y +CONFIG_SERIAL_SIFIVE=y +CONFIG_SERIAL_SIFIVE_CONSOLE=y CONFIG_SERIO=y CONFIG_SERIO_SERPORT=y -CONFIG_SGL_ALLOC=y CONFIG_SG_POOL=y CONFIG_SIFIVE_PLIC=y -# CONFIG_SIOX is not set -# CONFIG_SLIMBUS is not set CONFIG_SLUB_DEBUG=y CONFIG_SMP=y -# CONFIG_SOUNDWIRE is not set CONFIG_SPARSE_IRQ=y CONFIG_SPI=y CONFIG_SPI_BITBANG=y CONFIG_SPI_MASTER=y CONFIG_SPI_MEM=y +CONFIG_SPI_SIFIVE=y CONFIG_SRCU=y CONFIG_STACKTRACE=y CONFIG_SWIOTLB=y CONFIG_SWPHY=y CONFIG_SYSCTL_EXCEPTION_TRACE=y CONFIG_SYSFS_SYSCALL=y -# CONFIG_SYSTEM_EXTRA_CERTIFICATE is not set CONFIG_THREAD_INFO_IN_TASK=y CONFIG_TICK_CPU_ACCOUNTING=y CONFIG_TIMER_OF=y @@ -327,9 +294,7 @@ CONFIG_TRACE_CLOCK=y CONFIG_TREE_RCU=y CONFIG_TREE_SRCU=y CONFIG_TUNE_GENERIC=y -# CONFIG_TYPEC is not set CONFIG_UEVENT_HELPER_PATH="" -# CONFIG_UNISYSSPAR is not set CONFIG_USB=y CONFIG_USB_COMMON=y CONFIG_USB_EHCI_HCD=y @@ -359,8 +324,6 @@ CONFIG_VIRTIO_MMIO=y CONFIG_VIRTIO_NET=y CONFIG_VM_EVENT_COUNTERS=y CONFIG_X509_CERTIFICATE_PARSER=y -# CONFIG_XDP_SOCKETS is not set -# CONFIG_XILINX_VCU is not set CONFIG_XPS=y CONFIG_ZLIB_INFLATE=y CONFIG_ZONE_DMA32=y diff --git a/target/linux/riscv64/patches/0009-RISC-V-Networking-fix-Hack.patch b/target/linux/riscv64/patches/0009-RISC-V-Networking-fix-Hack.patch new file mode 100644 index 0000000000..35009a2f8e --- /dev/null +++ b/target/linux/riscv64/patches/0009-RISC-V-Networking-fix-Hack.patch @@ -0,0 +1,39 @@ +From aa230e7dc2ab01db5b630f427e57297ffc25c884 Mon Sep 17 00:00:00 2001 +From: Atish Patra +Date: Fri, 7 Sep 2018 10:22:27 -0700 +Subject: [PATCH 09/11] RISC-V: Networking fix Hack + +It looks like that kernel driver now supports reseting the +signal one additional time. As it had been already reset +twice in FSBL, PHY gets into incorrect state causing below error. + +---------------------------------------------------------------------- +macb 10090000.ethernet (unnamed net_device) (uninitialized): Could not attach to PHY +macb: probe of 10090000.ethernet failed with error -110 +---------------------------------------------------------------------- + +This patch is just a temporary fix until we have a fix a FSBL. +It is just a **HACK** and **NOT TO BE MERGED** into mainline. + +Signed-off-by: Atish Patra +--- + drivers/net/phy/mdio_bus.c | 3 --- + 1 file changed, 3 deletions(-) + +diff --git a/drivers/net/phy/mdio_bus.c b/drivers/net/phy/mdio_bus.c +index 98f4b1f7..02c31f83 100644 +--- a/drivers/net/phy/mdio_bus.c ++++ b/drivers/net/phy/mdio_bus.c +@@ -64,9 +64,6 @@ static int mdiobus_register_gpiod(struct mdio_device *mdiodev) + + mdiodev->reset = gpiod; + +- /* Assert the reset signal again */ +- mdio_device_reset(mdiodev, 1); +- + return 0; + } + +-- +2.7.4 + diff --git a/target/linux/riscv64/patches/0010-pcie-microsemi-added-support-for-the-Vera-board-root.patch b/target/linux/riscv64/patches/0010-pcie-microsemi-added-support-for-the-Vera-board-root.patch new file mode 100644 index 0000000000..47c75ead58 --- /dev/null +++ b/target/linux/riscv64/patches/0010-pcie-microsemi-added-support-for-the-Vera-board-root.patch @@ -0,0 +1,804 @@ +From 1fd6c8fbc07bec3c18771738ce4b2aad3ed228f2 Mon Sep 17 00:00:00 2001 +From: "Wesley W. Terpstra" +Date: Wed, 25 Apr 2018 12:10:15 -0700 +Subject: [PATCH 10/11] pcie-microsemi: added support for the Vera-board root + complex + +--- + drivers/pci/controller/Kconfig | 6 + + drivers/pci/controller/Makefile | 1 + + drivers/pci/controller/pcie-microsemi.c | 754 ++++++++++++++++++++++++++++++++ + 3 files changed, 761 insertions(+) + create mode 100644 drivers/pci/controller/pcie-microsemi.c + +diff --git a/drivers/pci/controller/Kconfig b/drivers/pci/controller/Kconfig +index 028b2874..4458c119 100644 +--- a/drivers/pci/controller/Kconfig ++++ b/drivers/pci/controller/Kconfig +@@ -278,5 +278,11 @@ config VMD + To compile this driver as a module, choose M here: the + module will be called vmd. + ++config PCIE_MICROSEMI ++ bool "Microsemi AXI PCIe host bridge support" ++ depends on OF || COMPILE_TEST ++ help ++ Say 'Y' here if you want kernel to support the Microsemi AXI PCIe ++ Host Bridge driver. + source "drivers/pci/controller/dwc/Kconfig" + endmenu +diff --git a/drivers/pci/controller/Makefile b/drivers/pci/controller/Makefile +index d56a5074..c3b76ff2 100644 +--- a/drivers/pci/controller/Makefile ++++ b/drivers/pci/controller/Makefile +@@ -28,6 +28,7 @@ obj-$(CONFIG_PCIE_ROCKCHIP_HOST) += pcie-rockchip-host.o + obj-$(CONFIG_PCIE_MEDIATEK) += pcie-mediatek.o + obj-$(CONFIG_PCIE_MOBIVEIL) += pcie-mobiveil.o + obj-$(CONFIG_PCIE_TANGO_SMP8759) += pcie-tango.o ++obj-$(CONFIG_PCIE_MICROSEMI) += pcie-microsemi.o + obj-$(CONFIG_VMD) += vmd.o + # pcie-hisi.o quirks are needed even without CONFIG_PCIE_DW + obj-y += dwc/ +diff --git a/drivers/pci/controller/pcie-microsemi.c b/drivers/pci/controller/pcie-microsemi.c +new file mode 100644 +index 00000000..9e2abca2 +--- /dev/null ++++ b/drivers/pci/controller/pcie-microsemi.c +@@ -0,0 +1,754 @@ ++/* ++ * PCIe host controller driver for Microsemi AXI PCIe Bridge ++ * ++ * Copyright (c) 2018 - Microsemi. ++ * Author: Badal Nilawar ++ * ++ * Based on the Xilinx, Altera PCIe driver ++ * ++ * ++ * This program is free software: you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License as published by ++ * the Free Software Foundation, either version 2 of the License, or ++ * (at your option) any later version. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include "../pci.h" ++ ++/* ECAM definitions */ ++#define ECAM_BUS_NUM_SHIFT 20 ++#define ECAM_DEV_NUM_SHIFT 12 ++ ++/* Number of MSI IRQs */ ++#define MICROSEMI_NUM_MSI_IRQS 32 ++ ++/* PCIe Bridge Phy and Controller Phy offsets */ ++#define PCIE0_BRIDGE_PHY_ADDR_OFFSET 0x03004000u ++#define PCIE0_CRTL_PHY_ADDR_OFFSET 0x03006000u ++ ++#define PCIE0_BRIDGE_ADDR 0x03004000u ++#define PCIE0_CRTL_ADDR 0x03006000u ++ ++#define PCIE1_BRIDGE_ADDR 0x00008000u ++#define PCIE1_CRTL_ADDR 0x0000A000u ++ ++/* PCIe LTSSM State reg */ ++#define LTSSM_STATE 0x5c ++ ++/* PCIe LTSSM L0 state */ ++#define LTSSM_L0_STATE 0x10 ++ ++/* PCIe Controller Phy Regs */ ++#define SEC_ERROR_INT 0x28 ++#define SEC_ERROR_INT_MASK 0x2c ++#define DED_ERROR_INT 0x30 ++#define DED_ERROR_INT_MASK 0x34 ++#define ECC_CONTROL 0x38 ++#define PCIE_EVENT_INT 0x14c ++ ++/* PCIe Bridge Phy Regs */ ++#define IMASK_LOCAL 0x180 ++#define ISTATUS_LOCAL 0x184 ++#define IMASK_HOST 0x188 ++#define ISTATUS_HOST 0x18c ++#define ISTATUS_MSI 0x194 ++#define PCIE_PCI_IDS_DW1 0x9c ++ ++/* PCIe AXI slave table init defines */ ++#define ATR0_AXI4_SLV0_SRCADDR_PARAM 0x800u ++#define ATR0_AXI4_SLV0_SRC_ADDR 0x804u ++#define ATR0_AXI4_SLV0_TRSL_ADDR_LSB 0x808u ++#define ATR0_AXI4_SLV0_TRSL_ADDR_UDW 0x80cu ++#define ATR0_AXI4_SLV0_TRSL_PARAM 0x810u ++ ++#define ATR1_AXI4_SLV0_SRCADDR_PARAM 0x820u ++#define ATR1_AXI4_SLV0_SRC_ADDR 0x824u ++#define ATR1_AXI4_SLV0_TRSL_ADDR_LSB 0x828u ++#define ATR1_AXI4_SLV0_TRSL_ADDR_UDW 0x82cu ++#define ATR1_AXI4_SLV0_TRSL_PARAM 0x830u ++ ++/* PCIe Master table init defines */ ++#define ATR0_PCIE_WIN0_SRCADDR_PARAM 0x600u ++ ++/* Translated ID */ ++#define PCIE_TX_RX_INTERFACE 0x00000000u ++#define PCIE_CONFIG_INTERFACE 0x00000001u ++ ++/* PCIe Config space MSI capability structure */ ++#define PCIE_ENABLE_MSI 0x10000000u ++ ++/* MSI definitions */ ++#define MSI_MSG_ADDR 0x190u ++#define MSI_ENABLE (0x01u << 16) ++#define MSI_ENABLE_MULTI (MICROSEMI_NUM_MSI_IRQS << 20) ++ ++/* MSI Capability Structure */ ++#define MSI_CAP_CTRL 0xE0u ++#define MSI_MSG_ADDR_OFFSET 0xE4u ++#define MSI_MSG_UPPER_ADDR_OFFEST 0xE8u ++#define MSI_MSG_DATA 0xF0u ++ ++ ++ ++/******************************************************************************/ ++/*Enable PCIe local*/ ++#define PCIE_LOCAL_INT_ENABLE 0xF000000u ++ ++/******************************************************************************/ ++/* Clear PCIe interrupt events */ ++#define PCIE_EVENT_INT_DATA 0x00070007u ++#define PCIE_ECC_DISABLE 0x0F000000u ++#define PCIE_SEC_ERROR_INT_CLEAR 0x0000FFFFu ++#define PCIE_DED_ERROR_INT_CLEAR 0x0000FFFFu ++#define PCIE_ISTATUS_CLEAR 0xFFFFFFFFu ++#define PCIE_CLEAR 0x00000000u ++#define PCIE_SET 0x00000001u ++ ++#define ROOT_PORT_ENABLE 0x00000001u ++ ++#define NULL_POINTER 0x00000000u ++ ++/*****************************************************************************/ ++/* PCIe Controller 0 */ ++#define PF_PCIE_CTRL_0 0u ++/* PCIe Controller 1 */ ++#define PF_PCIE_CTRL_1 1u ++ ++/* It indicates that the ATR table is enabled */ ++#define PF_PCIE_ATR_TABLE_ENABLE 1u ++/* It indicates that the the ATR table is disabled */ ++#define PF_PCIE_ATR_TABLE_DISABLE 0u ++ ++ ++/** ++ * struct microsemi_pcie_port - PCIe port information ++ * @reg_base: IO Mapped Register Base ++ * @irq: Interrupt number ++ * @root_busno: Root Bus number ++ * @dev: Device pointer ++ * @msi_domain: MSI IRQ domain pointer ++ * @leg_domain: Legacy IRQ domain pointer ++ * @resources: Bus Resources ++ */ ++struct microsemi_pcie_port { ++ struct platform_device *pdev; ++ void __iomem *reg_base; ++ void __iomem *reg_base_apb; ++ void __iomem *reg_bridge_apb; ++ void __iomem *reg_ctrl_apb; ++ u32 irq; ++ u8 root_busno; ++ struct device *dev; ++ struct irq_domain *msi_domain; ++ struct irq_domain *leg_domain; ++ struct list_head resources; ++}; ++ ++static DECLARE_BITMAP(msi_irq_in_use, MICROSEMI_NUM_MSI_IRQS); ++ ++static inline u32 pcie_read(struct microsemi_pcie_port *port, u32 reg) ++{ ++ return readl(port->reg_base + reg); ++} ++ ++static inline void pcie_write(struct microsemi_pcie_port *port, ++ u32 val, u32 reg) ++{ ++ writel(val, port->reg_base + reg); ++} ++ ++static inline bool microsemi_pcie_link_up(struct microsemi_pcie_port *port) ++{ ++ return (readl(port->reg_ctrl_apb + LTSSM_STATE) ++ & LTSSM_L0_STATE) ? 1 : 0; ++} ++ ++/** ++ * microsemi_pcie_valid_device - Check if a valid device is present on bus ++ * @bus: PCI Bus structure ++ * @devfn: device/function ++ * ++ * Return: 'true' on success and 'false' if invalid device is found ++ */ ++static bool microsemi_pcie_valid_device(struct pci_bus *bus, unsigned int devfn) ++{ ++ struct microsemi_pcie_port *port = bus->sysdata; ++ ++ /* Check if link is up when trying to access downstream ports */ ++ if (bus->number != port->root_busno) ++ if (!microsemi_pcie_link_up(port)) ++ return false; ++ ++ /* Only one device down on each root port */ ++ if (bus->number == port->root_busno && devfn > 0) ++ return false; ++ ++ return true; ++} ++ ++/** ++ * microsemi_pcie_map_bus - Get configuration base ++ * @bus: PCI Bus structure ++ * @devfn: Device/function ++ * @where: Offset from base ++ * ++ * Return: Base address of the configuration space needed to be ++ * accessed. ++ */ ++static void __iomem *microsemi_pcie_map_bus(struct pci_bus *bus, ++ unsigned int devfn, int where) ++{ ++ struct microsemi_pcie_port *port = bus->sysdata; ++ int relbus; ++ ++ ++ if (!microsemi_pcie_valid_device(bus, devfn)) ++ return NULL; ++ ++ relbus = (bus->number << ECAM_BUS_NUM_SHIFT) | ++ (devfn << ECAM_DEV_NUM_SHIFT); ++ ++ ++ return port->reg_base + relbus + where; ++} ++ ++/* PCIe operations */ ++static struct pci_ops microsemi_pcie_ops = { ++ .map_bus = microsemi_pcie_map_bus, ++ .read = pci_generic_config_read, ++ .write = pci_generic_config_write, ++}; ++ ++/* MSI functions */ ++ ++/** ++ * microsemi_pcie_destroy_msi - Free MSI number ++ * @irq: IRQ to be freed ++ */ ++static void microsemi_pcie_destroy_msi(unsigned int irq) ++{ ++ struct msi_desc *msi; ++ struct microsemi_pcie_port *port; ++ struct irq_data *d = irq_get_irq_data(irq); ++ irq_hw_number_t hwirq = irqd_to_hwirq(d); ++ ++ if (!test_bit(hwirq, msi_irq_in_use)) { ++ msi = irq_get_msi_desc(irq); ++ port = msi_desc_to_pci_sysdata(msi); ++ dev_err(port->dev, "Trying to free unused MSI#%d\n", irq); ++ } else { ++ clear_bit(hwirq, msi_irq_in_use); ++ } ++} ++ ++/** ++ * microsemi_pcie_assign_msi - Allocate MSI number ++ * ++ * Return: A valid IRQ on success and error value on failure. ++ */ ++static int microsemi_pcie_assign_msi(void) ++{ ++ int pos; ++ ++ pos = find_first_zero_bit(msi_irq_in_use, MICROSEMI_NUM_MSI_IRQS); ++ if (pos < MICROSEMI_NUM_MSI_IRQS) ++ set_bit(pos, msi_irq_in_use); ++ else ++ return -ENOSPC; ++ ++ return pos; ++} ++ ++/** ++ * microsemi_msi_teardown_irq - Destroy the MSI ++ * @chip: MSI Chip descriptor ++ * @irq: MSI IRQ to destroy ++ */ ++static void microsemi_msi_teardown_irq(struct msi_controller *chip, ++ unsigned int irq) ++{ ++ microsemi_pcie_destroy_msi(irq); ++ irq_dispose_mapping(irq); ++} ++ ++/** ++ * microsemi_pcie_msi_setup_irq - Setup MSI request ++ * @chip: MSI chip pointer ++ * @pdev: PCIe device pointer ++ * @desc: MSI descriptor pointer ++ * ++ * Return: '0' on success and error value on failure ++ */ ++static int microsemi_pcie_msi_setup_irq(struct msi_controller *chip, ++ struct pci_dev *pdev, ++ struct msi_desc *desc) ++{ ++ struct microsemi_pcie_port *port = pdev->bus->sysdata; ++ unsigned int irq; ++ int hwirq; ++ struct msi_msg msg; ++ ++ hwirq = microsemi_pcie_assign_msi(); ++ if (hwirq < 0) ++ return hwirq; ++ ++ irq = irq_create_mapping(port->msi_domain, hwirq); ++ if (!irq) ++ return -EINVAL; ++ ++ irq_set_msi_desc(irq, desc); ++ ++ msg.address_hi = 0; ++ msg.address_lo = MSI_MSG_ADDR; ++ msg.data = hwirq; ++ ++ pci_write_msi_msg(irq, &msg); ++ ++ return 0; ++} ++ ++/* MSI Chip Descriptor */ ++static struct msi_controller microsemi_pcie_msi_chip = { ++ .setup_irq = microsemi_pcie_msi_setup_irq, ++ .teardown_irq = microsemi_msi_teardown_irq, ++}; ++ ++/* HW Interrupt Chip Descriptor */ ++static struct irq_chip microsemi_msi_irq_chip = { ++ .name = "Microsemi PCIe MSI", ++ .irq_enable = pci_msi_unmask_irq, ++ .irq_disable = pci_msi_mask_irq, ++ .irq_mask = pci_msi_mask_irq, ++ .irq_unmask = pci_msi_unmask_irq, ++}; ++ ++/** ++ * microsemi_pcie_msi_map - Set the handler for the MSI and mark IRQ as valid ++ * @domain: IRQ domain ++ * @irq: Virtual IRQ number ++ * @hwirq: HW interrupt number ++ * ++ * Return: Always returns 0. ++ */ ++static int microsemi_pcie_msi_map(struct irq_domain *domain, unsigned int irq, ++ irq_hw_number_t hwirq) ++{ ++ irq_set_chip_and_handler(irq, ++ µsemi_msi_irq_chip, handle_simple_irq); ++ irq_set_chip_data(irq, domain->host_data); ++ ++ return 0; ++} ++ ++/* IRQ Domain operations */ ++static const struct irq_domain_ops msi_domain_ops = { ++ .map = microsemi_pcie_msi_map, ++}; ++ ++/** ++ * microsemi_pcie_enable_msi - Enable MSI support ++ * @port: PCIe port information ++ */ ++static void microsemi_pcie_enable_msi(struct microsemi_pcie_port *port) ++{ ++ u32 cap_ctrl; ++ ++ cap_ctrl = pcie_read(port, MSI_CAP_CTRL); ++ ++ pcie_write(port, cap_ctrl | MSI_ENABLE_MULTI | MSI_ENABLE, MSI_CAP_CTRL); ++ pcie_write(port, MSI_MSG_ADDR, MSI_MSG_ADDR_OFFSET); ++} ++ ++/* INTx Functions */ ++ ++/** ++ * microsemi_pcie_intx_map - Set the handler for the INTx and mark IRQ as valid ++ * @domain: IRQ domain ++ * @irq: Virtual IRQ number ++ * @hwirq: HW interrupt number ++ * ++ * Return: Always returns 0. ++ */ ++static int microsemi_pcie_intx_map(struct irq_domain *domain, unsigned int irq, ++ irq_hw_number_t hwirq) ++{ ++ irq_set_chip_and_handler(irq, &dummy_irq_chip, handle_simple_irq); ++ irq_set_chip_data(irq, domain->host_data); ++ ++ return 0; ++} ++ ++/* INTx IRQ Domain operations */ ++static const struct irq_domain_ops intx_domain_ops = { ++ .map = microsemi_pcie_intx_map, ++ .xlate = pci_irqd_intx_xlate, ++}; ++ ++/* PCIe HW Functions */ ++ ++/** ++ * microsemi_pcie_intr_handler - Interrupt Service Handler ++ * @irq: IRQ number ++ * @data: PCIe port information ++ * ++ * Return: IRQ_HANDLED on success and IRQ_NONE on failure ++ */ ++static irqreturn_t microsemi_pcie_intr_handler(int irq, void *data) ++{ ++ struct microsemi_pcie_port *port = (struct microsemi_pcie_port *)data; ++ struct device *dev = port->dev; ++ unsigned long status; ++ unsigned long msi; ++ u32 bit; ++ u32 virq; ++ ++ ++ status = readl(port->reg_bridge_apb + ISTATUS_LOCAL); ++ ++ status = (status >> 24) & 0x0f; ++ for_each_set_bit(bit, &status, PCI_NUM_INTX) { ++ /* clear interrupts */ ++ writel(1 << (bit+24), ++ port->reg_bridge_apb + ISTATUS_LOCAL); ++ ++ virq = irq_find_mapping(port->leg_domain, bit); ++ ++ if (virq) ++ generic_handle_irq(virq); ++ else ++ dev_err(dev, "unexpected IRQ, INT%d\n", bit); ++ } ++ ++ status = readl(port->reg_bridge_apb + ISTATUS_LOCAL); ++ if ((status & 0x10000000) == 0x10000000) { ++ writel((1 << 28), port->reg_bridge_apb + ISTATUS_LOCAL); ++ msi = readl(port->reg_bridge_apb + ISTATUS_MSI); ++ for_each_set_bit(bit, &msi, MICROSEMI_NUM_MSI_IRQS) { ++ /* clear interrupts */ ++ writel((1 << bit), ++ port->reg_bridge_apb + ISTATUS_MSI); ++ virq = irq_find_mapping(port->msi_domain, bit); ++ if (virq) ++ generic_handle_irq(virq); ++ else ++ dev_err(dev, "unexpected IRQ, INT%d\n", bit); ++ } ++ } ++ ++ return IRQ_HANDLED; ++} ++ ++/** ++ * microsemi_pcie_init_irq_domain - Initialize IRQ domain ++ * @port: PCIe port information ++ * ++ * Return: '0' on success and error value on failure ++ */ ++static int microsemi_pcie_init_irq_domain(struct microsemi_pcie_port *port) ++{ ++ struct device *dev = port->dev; ++ struct device_node *node = dev->of_node; ++ struct device_node *pcie_intc_node; ++ ++ /* Setup INTx */ ++ pcie_intc_node = of_get_next_child(node, NULL); ++ if (!pcie_intc_node) { ++ dev_err(dev, "No PCIe Intc node found\n"); ++ return -ENODEV; ++ } ++ dev_info(dev, "Intc node foundi %s\n", pcie_intc_node->name); ++ ++ port->leg_domain = irq_domain_add_linear(pcie_intc_node, PCI_NUM_INTX, ++ &intx_domain_ops, ++ port); ++ if (!port->leg_domain) { ++ dev_err(dev, "Failed to get a INTx IRQ domain\n"); ++ return -ENODEV; ++ } ++ ++ /* Setup MSI */ ++ if (IS_ENABLED(CONFIG_PCI_MSI)) { ++ port->msi_domain = irq_domain_add_linear(node, ++ MICROSEMI_NUM_MSI_IRQS, ++ &msi_domain_ops, ++ µsemi_pcie_msi_chip); ++ if (!port->msi_domain) { ++ dev_err(dev, "Failed to get a MSI IRQ domain\n"); ++ return -ENODEV; ++ } ++ microsemi_pcie_enable_msi(port); ++ } ++ return 0; ++} ++ ++/** ++ * microsemi_pcie_init_port - Parse Device tree, Initialize hardware ++ * @port: PCIe port information ++ * ++ * Return: '0' on success and error value on failure ++ */ ++static int microsemi_pcie_init_port(struct microsemi_pcie_port *port) ++{ ++ struct device *dev = port->dev; ++ struct device_node *node = dev->of_node; ++ struct of_pci_range_parser parser; ++ struct of_pci_range range; ++ struct resource regs; ++ struct resource regs1; ++ resource_size_t size; ++ u32 bit, pf_bridge_id = 1; ++ const char *type; ++ int err; ++ ++ type = of_get_property(node, "device_type", NULL); ++ if (!type || strcmp(type, "pci")) { ++ dev_err(dev, "invalid \"device_type\" %s\n", type); ++ return -EINVAL; ++ } ++ ++ err = of_address_to_resource(node, 0, ®s); ++ if (err) { ++ dev_err(dev, "missing \"reg\" property\n"); ++ return err; ++ } ++ ++ port->reg_base = devm_pci_remap_cfg_resource(dev, ®s); ++ if (IS_ERR(port->reg_base)) ++ return PTR_ERR(port->reg_base); ++ ++ ++ err = of_address_to_resource(node, 1, ®s1); ++ if (err) { ++ dev_err(dev, "missing \"reg\" property\n"); ++ return err; ++ } ++ ++ ++ port->reg_base_apb = devm_ioremap_resource(dev, ®s1); ++ if (IS_ERR(port->reg_base_apb)) ++ return PTR_ERR(port->reg_base_apb); ++ ++ if (pf_bridge_id == 0) { ++ port->reg_bridge_apb = port->reg_base_apb + PCIE0_BRIDGE_ADDR; ++ port->reg_ctrl_apb = port->reg_base_apb + PCIE0_CRTL_ADDR; ++ } else { ++ port->reg_bridge_apb = port->reg_base_apb + PCIE1_BRIDGE_ADDR; ++ port->reg_ctrl_apb = port->reg_base_apb + PCIE1_CRTL_ADDR; ++ } ++ ++ port->irq = irq_of_parse_and_map(node, 0); ++ ++ err = devm_request_irq(dev, port->irq, microsemi_pcie_intr_handler, ++ IRQF_SHARED | IRQF_NO_THREAD, ++ "microsemi-pcie", port); ++ if (err) { ++ dev_err(dev, "unable to request irq %d\n", port->irq); ++ return err; ++ } ++ ++ ++ /* Clear and Disable interrupts */ ++ ++ writel(0x0f000000, port->reg_ctrl_apb + ECC_CONTROL); ++ writel(0x00070007, port->reg_ctrl_apb + PCIE_EVENT_INT); ++ writel(0x0000ffff, port->reg_ctrl_apb + SEC_ERROR_INT); ++ writel(0x0000ffff, port->reg_ctrl_apb + SEC_ERROR_INT_MASK); ++ writel(0x0000ffff, port->reg_ctrl_apb + DED_ERROR_INT); ++ writel(0x0000ffff, port->reg_ctrl_apb + DED_ERROR_INT_MASK); ++ ++ writel(0x00000000, port->reg_bridge_apb + IMASK_LOCAL); ++ writel(0xffffffff, port->reg_bridge_apb + ISTATUS_LOCAL); ++ writel(0x00000000, port->reg_bridge_apb + IMASK_HOST); ++ writel(0xffffffff, port->reg_bridge_apb + ISTATUS_HOST); ++ ++ dev_info(dev, "interrupt disabled\n"); ++ ++ /* Configure Address Translation Table 0 for pcie config space */ ++ ++ writel(PCIE_CONFIG_INTERFACE, ++ port->reg_bridge_apb + ATR0_AXI4_SLV0_TRSL_PARAM); ++ ++ size = resource_size(®s); ++ ++ bit = find_first_bit((const unsigned long *)&size, 64) - 1; ++ ++ writel((u32)regs.start | bit << 1 | 0x01, ++ port->reg_bridge_apb + ATR0_AXI4_SLV0_SRCADDR_PARAM); ++ ++// writel((u32)(regs.start >> 32), ++// port->reg_bridge_apb + ATR0_AXI4_SLV0_SRC_ADDR); ++ ++ writel((u32)regs.start, ++ port->reg_bridge_apb + ATR0_AXI4_SLV0_TRSL_ADDR_LSB); ++ ++// writel((u32)(regs.start >> 32), ++// port->reg_bridge_apb + ATR0_AXI4_SLV0_TRSL_ADDR_UDW); ++ ++ ++ if (of_pci_range_parser_init(&parser, node)) { ++ dev_err(dev, "missing \"ranges\" property\n"); ++ return -EINVAL; ++ } ++ ++ ++ for_each_of_pci_range(&parser, &range) { ++ switch (range.flags & IORESOURCE_TYPE_BITS) { ++ case IORESOURCE_MEM: ++ ++ size = range.size; ++ bit = find_first_bit((const unsigned long *)&size, 64) - 1; ++ ++ /* Configure Address Translation Table 1 for pcie mem space */ ++ ++ writel(PCIE_TX_RX_INTERFACE, ++ port->reg_bridge_apb + ATR1_AXI4_SLV0_TRSL_PARAM); ++ ++ writel((u32)range.cpu_addr | bit << 1 | 0x01, ++ port->reg_bridge_apb + ATR1_AXI4_SLV0_SRCADDR_PARAM); ++ ++// writel((u32)(range.cpu_addr >> 32), ++// port->reg_bridge_apb + ATR1_AXI4_SLV0_SRC_ADDR); ++ ++ writel((u32)range.pci_addr, ++ port->reg_bridge_apb + ATR1_AXI4_SLV0_TRSL_ADDR_LSB); ++ ++// writel((u32)(range.pci_addr >> 32), ++// port->reg_bridge_apb + ATR1_AXI4_SLV0_TRSL_ADDR_UDW); ++ ++ break; ++ } ++ ++ } ++ ++ ++ writel(readl(port->reg_bridge_apb + ATR0_PCIE_WIN0_SRCADDR_PARAM) ++ | 0x3E, ++ port->reg_bridge_apb + ATR0_PCIE_WIN0_SRCADDR_PARAM); ++ ++ writel(0, port->reg_bridge_apb + 0x604); ++ ++ writel((readl(port->reg_bridge_apb + PCIE_PCI_IDS_DW1) & 0xffff) ++ | (PCI_CLASS_BRIDGE_PCI << 16), ++ port->reg_bridge_apb + PCIE_PCI_IDS_DW1); ++ ++ pcie_write(port, 0x00ff0100, 0x18); ++ ++ /* Enable interrupts */ ++ writel(PCIE_ENABLE_MSI | PCIE_LOCAL_INT_ENABLE, ++ port->reg_bridge_apb + IMASK_LOCAL); ++ ++ ++ return 0; ++} ++ ++/** ++ * microsemi_pcie_probe - Probe function ++ * @pdev: Platform device pointer ++ * ++ * Return: '0' on success and error value on failure ++ */ ++static int microsemi_pcie_probe(struct platform_device *pdev) ++{ ++ struct device *dev = &pdev->dev; ++ struct microsemi_pcie_port *port; ++ struct pci_bus *bus, *child; ++ struct pci_host_bridge *bridge; ++ int err; ++ resource_size_t iobase = 0; ++ LIST_HEAD(res); ++ ++ pr_err("%s In \n", __func__); ++ if (!dev->of_node) ++ return -ENODEV; ++ ++ bridge = devm_pci_alloc_host_bridge(dev, sizeof(*port)); ++ if (!bridge) ++ return -ENODEV; ++ ++ port = pci_host_bridge_priv(bridge); ++ ++ port->dev = dev; ++ port->pdev = pdev; ++ ++ err = microsemi_pcie_init_port(port); ++ if (err) { ++ dev_err(dev, "Pcie port initialization failed\n"); ++ return err; ++ } ++ ++ ++ err = microsemi_pcie_init_irq_domain(port); ++ if (err) { ++ dev_err(dev, "Failed creating IRQ Domain\n"); ++ return err; ++ } ++ ++ err = devm_of_pci_get_host_bridge_resources(dev, 0, 0xff, &res, ++ &iobase); ++ if (err) { ++ dev_err(dev, "Getting bridge resources failed\n"); ++ return err; ++ } ++ ++ err = devm_request_pci_bus_resources(dev, &res); ++ if (err) ++ goto error; ++ ++ ++ list_splice_init(&res, &bridge->windows); ++ bridge->dev.parent = dev; ++ bridge->sysdata = port; ++ bridge->busnr = 0; ++ bridge->ops = µsemi_pcie_ops; ++ bridge->map_irq = of_irq_parse_and_map_pci; ++ bridge->swizzle_irq = pci_common_swizzle; ++ ++#ifdef CONFIG_PCI_MSI ++ microsemi_pcie_msi_chip.dev = dev; ++ bridge->msi = µsemi_pcie_msi_chip; ++#endif ++ err = pci_scan_root_bus_bridge(bridge); ++ dev_info(dev, "pci_scan_root_bus_bridge done\n"); ++ if (err < 0) ++ goto error; ++ ++ bus = bridge->bus; ++ ++ pci_assign_unassigned_bus_resources(bus); ++ list_for_each_entry(child, &bus->children, node) ++ pcie_bus_configure_settings(child); ++ pci_bus_add_devices(bus); ++ ++ return 0; ++ ++error: ++ pci_free_resource_list(&res); ++ return err; ++} ++ ++static const struct of_device_id microsemi_pcie_of_match[] = { ++ { .compatible = "ms-pf,axi-pcie-host", }, ++ {} ++}; ++ ++static struct platform_driver microsemi_pcie_driver = { ++ .driver = { ++ .name = "microsemi-pcie", ++ .of_match_table = microsemi_pcie_of_match, ++ .suppress_bind_attrs = true, ++ }, ++ .probe = microsemi_pcie_probe, ++}; ++builtin_platform_driver(microsemi_pcie_driver); +-- +2.7.4 + diff --git a/target/linux/riscv64/patches/002-clk-sifive-prci.patch b/target/linux/riscv64/patches/002-clk-sifive-prci.patch new file mode 100644 index 0000000000..11e27258da --- /dev/null +++ b/target/linux/riscv64/patches/002-clk-sifive-prci.patch @@ -0,0 +1,509 @@ +From 7f45b80bb9675e9ace37bc1c4fd8f0351dfd9de9 Mon Sep 17 00:00:00 2001 +From: "Wesley W. Terpstra" +Date: Tue, 13 Feb 2018 19:39:41 -0800 +Subject: [PATCH 1/5] u54-prci: driver for core U54 clocks + +--- + drivers/clk/sifive/Kconfig | 4 + + drivers/clk/sifive/Makefile | 1 + + drivers/clk/sifive/u54-prci.c | 314 ++++++++++++++++++++++++++++++++++ + 3 files changed, 319 insertions(+) + create mode 100644 drivers/clk/sifive/Kconfig + create mode 100644 drivers/clk/sifive/Makefile + create mode 100644 drivers/clk/sifive/u54-prci.c + +diff --git a/drivers/clk/sifive/Kconfig b/drivers/clk/sifive/Kconfig +new file mode 100644 +index 0000000000000..a562e0c6dc67e +--- /dev/null ++++ b/drivers/clk/sifive/Kconfig +@@ -0,0 +1,4 @@ ++config CLK_U54_PRCI ++ bool "PRCI driver for U54 SoCs" ++ ---help--- ++ Supports Power Reset Clock interface found in U540 SoCs +diff --git a/drivers/clk/sifive/Makefile b/drivers/clk/sifive/Makefile +new file mode 100644 +index 0000000000000..0c2b175b5846d +--- /dev/null ++++ b/drivers/clk/sifive/Makefile +@@ -0,0 +1 @@ ++obj-$(CONFIG_CLK_U54_PRCI) += u54-prci.o +diff --git a/drivers/clk/sifive/u54-prci.c b/drivers/clk/sifive/u54-prci.c +new file mode 100644 +index 0000000000000..edc4b7818e710 +--- /dev/null ++++ b/drivers/clk/sifive/u54-prci.c +@@ -0,0 +1,314 @@ ++/* ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License version 2 as ++ * published by the Free Software Foundation. ++ * ++ * This program is distributed in the hope that it will be useful, ++ * but WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the ++ * GNU General Public License for more details. ++ * ++ * Copyright (C) 2018 SiFive, Inc. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#define CORE_CLOCK 0 ++#define GEMTX_CLOCK 1 ++#define PRCI_CLOCKS 2 ++ ++#define MIN_REF 7000000UL ++#define MAX_REF 200000000UL ++#define MAX_PARENT 600000000UL ++#define MAX_VCO 4800000000UL ++#define MAX_DIV 64 ++#define MAX_R 64UL ++ ++#define PLL_LOCK 0x80000000U ++#define NAME_LEN 40 ++ ++struct sifive_u54_prci_driver; ++ ++struct sifive_u54_prci_pll { ++ struct clk_hw hw; ++ struct sifive_u54_prci_driver *driver; ++ char name[NAME_LEN]; ++ u32 freq; ++ u32 glcm; ++}; ++ ++struct sifive_u54_prci_driver { ++ struct clk_onecell_data table; ++ struct clk *clks[PRCI_CLOCKS]; ++ struct sifive_u54_prci_pll plls[PRCI_CLOCKS]; ++ void __iomem *reg; ++}; ++ ++#define to_sifive_u54_prci_pll(hw) container_of(hw, struct sifive_u54_prci_pll, hw) ++ ++struct sifive_u54_pll_cfg { ++ unsigned long r, f, q, a; ++}; ++ ++static struct sifive_u54_pll_cfg sifive_u54_pll_cfg(u32 reg) ++{ ++ struct sifive_u54_pll_cfg cfg; ++ cfg.r = (reg >> 0) & 0x3f; ++ cfg.f = (reg >> 6) & 0x1ff; ++ cfg.q = (reg >> 15) & 0x7; ++ cfg.a = (reg >> 18) & 0x7; ++ return cfg; ++} ++ ++static u32 sifive_u54_pll_reg(struct sifive_u54_pll_cfg cfg) ++{ ++ u32 reg = 0; ++ reg |= (cfg.r & 0x3f) << 0; ++ reg |= (cfg.f & 0x1ff) << 6; ++ reg |= (cfg.q & 0x7) << 15; ++ reg |= (cfg.a & 0x7) << 18; ++ reg |= 1<<25; // internal feedback ++ return reg; ++} ++ ++static unsigned long sifive_u54_pll_rate(struct sifive_u54_pll_cfg cfg, unsigned long parent) ++{ ++ return (parent*2*(cfg.f+1) / (cfg.r+1)) >> cfg.q; ++} ++ ++static struct sifive_u54_pll_cfg sifive_u54_pll_configure(unsigned long target, unsigned long parent) ++{ ++ struct sifive_u54_pll_cfg cfg; ++ unsigned long scale, ratio, best_delta, filter; ++ u32 max_r, best_r, best_f, r; ++ ++ /* Confirm input frequency is within bounds */ ++ if (WARN_ON(parent > MAX_PARENT)) { parent = MAX_PARENT; } ++ if (WARN_ON(parent < MIN_REF)) { parent = MIN_REF; } ++ ++ /* Calculate the Q shift and target VCO */ ++ scale = MAX_VCO / target; ++ if (scale <= 1) { ++ cfg.q = 1; ++ target = MAX_VCO; ++ } else if (scale > MAX_DIV) { ++ cfg.q = ilog2(MAX_DIV); ++ target = MAX_VCO/2; ++ } else { ++ cfg.q = ilog2(scale); ++ target = target << cfg.q; ++ } ++ ++ /* Precalcualte the target ratio */ ++ ratio = (target << 20) / parent; ++ ++ /* Placeholder values */ ++ best_r = 0; ++ best_f = 0; ++ best_delta = MAX_VCO; ++ ++ /* Consider all values for R which land within [MIN_REF, MAX_REF]; prefer smaller R */ ++ max_r = min(MAX_R, parent / MIN_REF); ++ for (r = DIV_ROUND_UP(parent, MAX_REF); r <= max_r; ++r) { ++ /* What is the best F we can pick in this case? */ ++ u32 f = (ratio*r + (1<<20)) >> 21; ++ unsigned long ref = parent / r; ++ unsigned long vco = ref * f * 2; ++ unsigned long delta; ++ ++ /* Ensure rounding didn't take us out of range */ ++ if (vco > target) --f; ++ if (vco < MAX_VCO/2) ++f; ++ vco = ref * f * 2; ++ ++ delta = abs(target - vco); ++ if (delta < best_delta) { ++ best_delta = delta; ++ best_r = r; ++ best_f = f; ++ } ++ } ++ ++ cfg.r = best_r - 1; ++ cfg.f = best_f - 1; ++ ++ /* Pick the best PLL jitter filter */ ++ filter = parent / best_r; ++ BUG_ON(filter < 7000000); ++ if (filter < 11000000) { ++ cfg.a = 1; ++ } else if (filter < 18000000) { ++ cfg.a = 2; ++ } else if (filter < 30000000) { ++ cfg.a = 3; ++ } else if (filter < 50000000) { ++ cfg.a = 4; ++ } else if (filter < 80000000) { ++ cfg.a = 5; ++ } else if (filter < 130000000) { ++ cfg.a = 6; ++ } else { ++ BUG_ON (filter > 200000000); ++ cfg.a = 7; ++ } ++ ++ return cfg; ++} ++ ++static unsigned long sifive_u54_prci_recalc_rate(struct clk_hw *hw, unsigned long parent_rate) ++{ ++ struct sifive_u54_prci_pll *pll = to_sifive_u54_prci_pll(hw); ++ struct sifive_u54_prci_driver *driver = pll->driver; ++ ++ u32 reg = ioread32(driver->reg + pll->freq); ++ struct sifive_u54_pll_cfg cfg = sifive_u54_pll_cfg(reg); ++ ++ return sifive_u54_pll_rate(cfg, parent_rate); ++} ++ ++static long sifive_u54_prci_round_rate(struct clk_hw *hw, unsigned long rate, unsigned long *parent_rate) ++{ ++ struct sifive_u54_pll_cfg cfg = sifive_u54_pll_configure(rate, *parent_rate); ++ return sifive_u54_pll_rate(cfg, *parent_rate); ++} ++ ++static int sifive_u54_prci_set_rate(struct clk_hw *hw, unsigned long rate, unsigned long parent_rate) ++{ ++ struct sifive_u54_prci_pll *pll = to_sifive_u54_prci_pll(hw); ++ struct sifive_u54_prci_driver *driver = pll->driver; ++ ++ struct sifive_u54_pll_cfg cfg = sifive_u54_pll_configure(rate, parent_rate); ++ u32 reg = sifive_u54_pll_reg(cfg); ++ ++ /* Switch to reg clock and reconfigure PLL */ ++ iowrite32(1, driver->reg + pll->glcm); ++ iowrite32(reg, driver->reg + pll->freq); ++ ++ /* Wait for lock and switch back to PLL */ ++ while (!(ioread32(driver->reg + pll->freq) & PLL_LOCK)); ++ iowrite32(0, driver->reg + pll->glcm); ++ ++ return 0; ++} ++ ++static const struct clk_ops sifive_u54_prci_ops_rw = { ++ .recalc_rate = sifive_u54_prci_recalc_rate, ++ .round_rate = sifive_u54_prci_round_rate, ++ .set_rate = sifive_u54_prci_set_rate, ++}; ++ ++static const struct clk_ops sifive_u54_prci_ops_ro = { ++ .recalc_rate = sifive_u54_prci_recalc_rate, ++}; ++ ++static ssize_t sifive_u54_pll_show(struct device *dev, struct device_attribute *attr, char *buf) ++{ ++ struct sifive_u54_prci_driver *driver = dev_get_drvdata(dev); ++ return sprintf(buf, "%ld", clk_get_rate(driver->clks[0])); ++} ++ ++static ssize_t sifive_u54_pll_rate_store(struct device *dev, struct device_attribute *attr, const char *buf, size_t count) ++{ ++ struct sifive_u54_prci_driver *driver = dev_get_drvdata(dev); ++ unsigned long rate; ++ char *endp; ++ ++ rate = simple_strtoul(buf, &endp, 0); ++ if (*endp != 0 && *endp != '\n') ++ return -EINVAL; ++ ++ clk_set_rate(driver->clks[0], rate); ++ return count; ++} ++ ++static DEVICE_ATTR(rate, 0644, sifive_u54_pll_show, sifive_u54_pll_rate_store); ++ ++static int sifive_u54_prci_probe(struct platform_device *pdev) ++{ ++ struct device *dev = &pdev->dev; ++ struct clk_init_data init; ++ struct sifive_u54_prci_driver *driver; ++ struct resource *res; ++ const char *parent; ++ int i; ++ ++ parent = of_clk_get_parent_name(dev->of_node, 0); ++ if (!parent) { ++ dev_err(dev, "No OF parent clocks found\n"); ++ return -EINVAL; ++ } ++ ++ driver = devm_kzalloc(dev, sizeof(*driver), GFP_KERNEL); ++ if (!driver) { ++ dev_err(dev, "Out of memory\n"); ++ return -ENOMEM; ++ } ++ ++ res = platform_get_resource(pdev, IORESOURCE_MEM, 0); ++ driver->reg = devm_ioremap_resource(dev, res); ++ if (IS_ERR(driver->reg)) ++ return PTR_ERR(driver->reg); ++ ++ /* Link the data structure */ ++ driver->table.clk_num = PRCI_CLOCKS; ++ driver->table.clks = &driver->clks[0]; ++ dev_set_drvdata(dev, driver); ++ ++ /* Describe the clocks */ ++ snprintf(driver->plls[CORE_CLOCK].name, NAME_LEN, "%s.core", dev->of_node->name); ++ driver->plls[CORE_CLOCK].freq = 0x4; ++ driver->plls[CORE_CLOCK].glcm = 0x24; ++ snprintf(driver->plls[GEMTX_CLOCK].name, NAME_LEN, "%s.gemtx", dev->of_node->name); ++ driver->plls[GEMTX_CLOCK].freq = 0x1c; ++ driver->plls[GEMTX_CLOCK].glcm = 0; /* None; cannot be set_rate */ ++ ++ /* Export the clocks */ ++ for (i = 0; i < PRCI_CLOCKS; ++i) { ++ init.name = &driver->plls[i].name[0]; ++ init.ops = driver->plls[i].glcm ? &sifive_u54_prci_ops_rw : &sifive_u54_prci_ops_ro; ++ init.num_parents = 1; ++ init.parent_names = &parent; ++ init.flags = 0; ++ ++ driver->plls[i].driver = driver; ++ driver->plls[i].hw.init = &init; ++ ++ driver->clks[i] = devm_clk_register(dev, &driver->plls[i].hw); ++ if (IS_ERR(driver->clks[i])) { ++ dev_err(dev, "Failed to register clock %d, %ld\n", i, PTR_ERR(driver->clks[i])); ++ return PTR_ERR(driver->clks[i]); ++ } ++ } ++ ++ of_clk_add_provider(dev->of_node, of_clk_src_onecell_get, &driver->table); ++ device_create_file(dev, &dev_attr_rate); ++ dev_info(dev, "Registered U54 core clocks\n"); ++ ++ return 0; ++} ++ ++static const struct of_device_id sifive_u54_prci_of_match[] = { ++ { .compatible = "sifive,aloeprci0", }, ++ {} ++}; ++ ++static struct platform_driver sifive_u54_prci_driver = { ++ .driver = { ++ .name = "sifive-u54-prci", ++ .of_match_table = sifive_u54_prci_of_match, ++ }, ++ .probe = sifive_u54_prci_probe, ++}; ++ ++static int __init sifive_u54_prci_init(void) ++{ ++ return platform_driver_register(&sifive_u54_prci_driver); ++} ++core_initcall(sifive_u54_prci_init); + +From 9b47a41c087008233d3024cc3f5005984a6c504c Mon Sep 17 00:00:00 2001 +From: Palmer Dabbelt +Date: Wed, 21 Feb 2018 10:06:48 -0800 +Subject: [PATCH 2/5] Fix some overflow warnings + +--- + drivers/clk/sifive/u54-prci.c | 18 +++++++++--------- + 1 file changed, 9 insertions(+), 9 deletions(-) + +diff --git a/drivers/clk/sifive/u54-prci.c b/drivers/clk/sifive/u54-prci.c +index edc4b7818e710..b8a93d1ebc2db 100644 +--- a/drivers/clk/sifive/u54-prci.c ++++ b/drivers/clk/sifive/u54-prci.c +@@ -24,15 +24,15 @@ + #define GEMTX_CLOCK 1 + #define PRCI_CLOCKS 2 + +-#define MIN_REF 7000000UL +-#define MAX_REF 200000000UL +-#define MAX_PARENT 600000000UL +-#define MAX_VCO 4800000000UL +-#define MAX_DIV 64 +-#define MAX_R 64UL +- +-#define PLL_LOCK 0x80000000U +-#define NAME_LEN 40 ++#define MIN_REF 7000000ULL ++#define MAX_REF 200000000ULL ++#define MAX_PARENT 600000000ULL ++#define MAX_VCO 4800000000ULL ++#define MAX_DIV 64ULL ++#define MAX_R 64ULL ++ ++#define PLL_LOCK 0x80000000ULL ++#define NAME_LEN 40ULL + + struct sifive_u54_prci_driver; + + +From 031060d77cfbd86d39dfb8863e4fa4f95b435b1b Mon Sep 17 00:00:00 2001 +From: Palmer Dabbelt +Date: Wed, 21 Feb 2018 13:00:16 -0800 +Subject: [PATCH 3/5] Include the sifive kconfig + +--- + drivers/clk/Kconfig | 1 + + 1 file changed, 1 insertion(+) + +diff --git a/drivers/clk/Kconfig b/drivers/clk/Kconfig +index 721572a8c4296..5b4bb0a23ffd3 100644 +--- a/drivers/clk/Kconfig ++++ b/drivers/clk/Kconfig +@@ -288,6 +288,7 @@ source "drivers/clk/mvebu/Kconfig" + source "drivers/clk/qcom/Kconfig" + source "drivers/clk/renesas/Kconfig" + source "drivers/clk/samsung/Kconfig" ++source "drivers/clk/sifive/Kconfig" + source "drivers/clk/sprd/Kconfig" + source "drivers/clk/sunxi-ng/Kconfig" + source "drivers/clk/tegra/Kconfig" + +From 9f8ca54f7c62aeb3245d8a70150d15e25ffb4f15 Mon Sep 17 00:00:00 2001 +From: Palmer Dabbelt +Date: Wed, 21 Feb 2018 13:40:10 -0800 +Subject: [PATCH 4/5] Only show the U64 clock driver on RISC-V + +This will probably only be on a RISC-V system, and it doesn't build on +32-bit systems without 64-bit divides which is a headache. + +Signed-off-by: Palmer Dabbelt +--- + drivers/clk/sifive/Kconfig | 1 + + 1 file changed, 1 insertion(+) + +diff --git a/drivers/clk/sifive/Kconfig b/drivers/clk/sifive/Kconfig +index a562e0c6dc67e..c324161700271 100644 +--- a/drivers/clk/sifive/Kconfig ++++ b/drivers/clk/sifive/Kconfig +@@ -1,4 +1,5 @@ + config CLK_U54_PRCI + bool "PRCI driver for U54 SoCs" ++ depends on RISCV + ---help--- + Supports Power Reset Clock interface found in U540 SoCs + +From d79106eca2349e212c4737c5646002bd864b1593 Mon Sep 17 00:00:00 2001 +From: "Wesley W. Terpstra" +Date: Tue, 13 Feb 2018 19:39:41 -0800 +Subject: [PATCH 5/5] u54-prci: driver for core U54 clocks + +--- + .../bindings/clock/sifive,u54-prci.txt | 44 +++++++++++++++++++ + 1 file changed, 44 insertions(+) + create mode 100644 Documentation/devicetree/bindings/clock/sifive,u54-prci.txt + +diff --git a/Documentation/devicetree/bindings/clock/sifive,u54-prci.txt b/Documentation/devicetree/bindings/clock/sifive,u54-prci.txt +new file mode 100644 +index 0000000000000..88682c5eaebc6 +--- /dev/null ++++ b/Documentation/devicetree/bindings/clock/sifive,u54-prci.txt +@@ -0,0 +1,44 @@ ++SiFive U54 SoC clocks ++ ++This binding uses the common clock binding: ++ Documentation/devicetree/bindings/clock/clock-bindings.txt ++ ++The U54 PRCI controller generates clocks for the U54 SoC. There is ++a core PLL that sets the processor frequency and PLLs for ethernet ++and DDR. It takes an input clock from the board, typically an oscillator ++or crystal. ++ ++Required properties: ++- compatible: Should be "sifive,aloeprci0" ++- #clock-cells: Should be <1> ++- reg: Specifies base physical address and size of the registers ++- clocks: phandles to the parent clock used as input ++ ++Example: ++ ++ refclk: refclk { ++ #clock-cells = <0>; ++ compatible = "fixed-clock"; ++ clock-frequency = <33333333>; ++ clock-output-names = "xtal"; ++ }; ++ ++ u54: prci@10000000 { ++ compatible = "sifive,aloeprci0"; ++ reg = <0x0 0x10000000 0x0 0x1000>; ++ clocks = <&refclk>; ++ #clock-cells = <1>; ++ }; ++ ++ tlclk: tlclk { ++ compatible = "fixed-factor-clock"; ++ clocks = <&u54 0>; /* Core frequency */ ++ #clock-cells = <0>; ++ clock-div = <2>; ++ clock-mult = <1>; ++ }; ++ ++ ethernet@10090000 { ++ ... ++ clocks = <&prci 1>; /* TX clock */ ++ }; +diff --git a/drivers/clk/Makefile b/drivers/clk/Makefile +index ae40cbe770f05..017d8d12551b6 100644 +--- a/drivers/clk/Makefile ++++ b/drivers/clk/Makefile +@@ -89,6 +89,7 @@ obj-$(CONFIG_COMMON_CLK_QCOM) += qcom/ + obj-y += renesas/ + obj-$(CONFIG_ARCH_ROCKCHIP) += rockchip/ + obj-$(CONFIG_COMMON_CLK_SAMSUNG) += samsung/ ++obj-y += sifive/ + obj-$(CONFIG_ARCH_SIRF) += sirf/ + obj-$(CONFIG_ARCH_SOCFPGA) += socfpga/ + obj-$(CONFIG_PLAT_SPEAR) += spear/ diff --git a/target/linux/riscv64/patches/003-clk-gemgxl.patch b/target/linux/riscv64/patches/003-clk-gemgxl.patch new file mode 100644 index 0000000000..c44befcafc --- /dev/null +++ b/target/linux/riscv64/patches/003-clk-gemgxl.patch @@ -0,0 +1,196 @@ +From 13317fd60728d24988fb8f5682bfaafe401b3a15 Mon Sep 17 00:00:00 2001 +From: "Wesley W. Terpstra" +Date: Tue, 6 Feb 2018 11:03:07 -0800 +Subject: [PATCH] gemgxl-mgmt: implement clock switch for GEM tx_clk + +Signed-off-by: Palmer Dabbelt +--- + +diff --git a/Documentation/devicetree/bindings/clock/sifive,gemgxl-mgmt.txt b/Documentation/devicetree/bindings/clock/sifive,gemgxl-mgmt.txt +new file mode 100644 +index 0000000000000..349489e33edaa +--- /dev/null ++++ b/Documentation/devicetree/bindings/clock/sifive,gemgxl-mgmt.txt +@@ -0,0 +1,26 @@ ++TX clock switch for GEMGXL in U540 SoCs ++ ++This binding uses the common clock binding: ++ Documentation/devicetree/bindings/clock/clock-bindings.txt ++ ++The U54 includes a clock mux to control the ethernet TX frequenecy. It ++switches between the local TX clock (125MHz) and PHY TX clocks. This is ++necessary to toggle between 1Gb and 100/10Mb speeds. ++ ++Required properties: ++- compatible: Should be "sifive,cadencegemgxlmgmt0" ++- #clock-cells: Should be <0> ++- reg: Specifies base physical address and size of the registers ++ ++Example: ++ ++ mgmt: cadence-gemgxl-mgmt@100a00000 { ++ compatible = "sifive,cadencegemgxlmgmt0"; ++ #clock-cells = <0>; ++ reg = <0x0 0x100a0000 0x0 0x1000>; ++ }; ++ ++ ethernet@10090000 { ++ ... ++ clocks = <&mgmt>; /* TX clock */ ++ }; +diff --git a/drivers/clk/sifive/Kconfig b/drivers/clk/sifive/Kconfig +index 0000000000000..284bffb121ebd +--- a/drivers/clk/sifive/Kconfig ++++ b/drivers/clk/sifive/Kconfig +@@ -0,0 +1,9 @@ ++config CLK_U54_PRCI ++ bool "PRCI driver for U54 SoCs" ++ ---help--- ++ Supports Power Reset Clock interface found in U540 SoCs ++ ++config CLK_GEMGXL_MGMT ++ bool "TX clock switch for GEMGXL in U540 SoCs" ++ ---help--- ++ Supports clock muxing between 10/100Mbit and 1Gbit TX clock on U540 SoCs +diff --git a/drivers/clk/sifive/Makefile b/drivers/clk/sifive/Makefile +index 0000000000000..7784d2ee0f446 +--- a/drivers/clk/sifive/Makefile ++++ b/drivers/clk/sifive/Makefile +@@ -0,0 +1,2 @@ ++obj-$(CONFIG_CLK_U54_PRCI) += u54-prci.o ++obj-$(CONFIG_CLK_GEMGXL_MGMT) += gemgxl-mgmt.o +diff --git a/drivers/clk/sifive/gemgxl-mgmt.c b/drivers/clk/sifive/gemgxl-mgmt.c +new file mode 100644 +index 0000000000000..00b07580fe3ce +--- /dev/null ++++ b/drivers/clk/sifive/gemgxl-mgmt.c +@@ -0,0 +1,129 @@ ++/* ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License version 2 as ++ * published by the Free Software Foundation. ++ * ++ * This program is distributed in the hope that it will be useful, ++ * but WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the ++ * GNU General Public License for more details. ++ * ++ * Copyright (C) 2018 SiFive, Inc. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++ ++struct sifive_gemgxl_mgmt { ++ void __iomem *reg; ++ unsigned long rate; ++ struct clk_hw hw; ++}; ++ ++#define to_sifive_gemgxl_mgmt(mgmt) container_of(mgmt, struct sifive_gemgxl_mgmt, hw) ++ ++static unsigned long sifive_gemgxl_mgmt_recalc_rate(struct clk_hw *hw, ++ unsigned long parent_rate) ++{ ++ struct sifive_gemgxl_mgmt *mgmt = to_sifive_gemgxl_mgmt(hw); ++ return mgmt->rate; ++} ++ ++static long sifive_gemgxl_mgmt_round_rate(struct clk_hw *hw, unsigned long rate, ++ unsigned long *parent_rate) ++{ ++ if (WARN_ON(rate < 2500000)) { ++ return 2500000; ++ } else if (rate == 2500000) { ++ return 2500000; ++ } else if (WARN_ON(rate < 13750000)) { ++ return 2500000; ++ } else if (WARN_ON(rate < 25000000)) { ++ return 25000000; ++ } else if (rate == 25000000) { ++ return 25000000; ++ } else if (WARN_ON(rate < 75000000)) { ++ return 25000000; ++ } else if (WARN_ON(rate < 125000000)) { ++ return 125000000; ++ } else if (rate == 125000000) { ++ return 125000000; ++ } else { ++ WARN_ON(rate > 125000000); ++ return 125000000; ++ } ++} ++ ++static int sifive_gemgxl_mgmt_set_rate(struct clk_hw *hw, unsigned long rate, ++ unsigned long parent_rate) ++{ ++ struct sifive_gemgxl_mgmt *mgmt = to_sifive_gemgxl_mgmt(hw); ++ rate = sifive_gemgxl_mgmt_round_rate(hw, rate, &parent_rate); ++ iowrite32(rate != 125000000, mgmt->reg); ++ mgmt->rate = rate; ++ return 0; ++} ++ ++static const struct clk_ops sifive_gemgxl_mgmt_ops = { ++ .recalc_rate = sifive_gemgxl_mgmt_recalc_rate, ++ .round_rate = sifive_gemgxl_mgmt_round_rate, ++ .set_rate = sifive_gemgxl_mgmt_set_rate, ++}; ++ ++static int sifive_gemgxl_mgmt_probe(struct platform_device *pdev) ++{ ++ struct clk_init_data init; ++ struct sifive_gemgxl_mgmt *mgmt; ++ struct resource *res; ++ struct clk *clk; ++ ++ mgmt = devm_kzalloc(&pdev->dev, sizeof(*mgmt), GFP_KERNEL); ++ if (!mgmt) ++ return -ENOMEM; ++ ++ res = platform_get_resource(pdev, IORESOURCE_MEM, 0); ++ mgmt->reg = devm_ioremap_resource(&pdev->dev, res); ++ if (IS_ERR(mgmt->reg)) ++ return PTR_ERR(mgmt->reg); ++ ++ init.name = pdev->dev.of_node->name; ++ init.ops = &sifive_gemgxl_mgmt_ops; ++ init.flags = 0; ++ init.num_parents = 0; ++ ++ mgmt->rate = 0; ++ mgmt->hw.init = &init; ++ ++ clk = clk_register(NULL, &mgmt->hw); ++ if (IS_ERR(clk)) ++ return PTR_ERR(clk); ++ ++ of_clk_add_provider(pdev->dev.of_node, of_clk_src_simple_get, clk); ++ ++ dev_info(&pdev->dev, "Registered clock switch '%s'\n", init.name); ++ ++ return 0; ++} ++ ++static const struct of_device_id sifive_gemgxl_mgmt_of_match[] = { ++ { .compatible = "sifive,cadencegemgxlmgmt0", }, ++ {} ++}; ++ ++static struct platform_driver sifive_gemgxl_mgmt_driver = { ++ .driver = { ++ .name = "sifive-gemgxl-mgmt", ++ .of_match_table = sifive_gemgxl_mgmt_of_match, ++ }, ++ .probe = sifive_gemgxl_mgmt_probe, ++}; ++ ++static int __init sifive_gemgxl_mgmt_init(void) ++{ ++ return platform_driver_register(&sifive_gemgxl_mgmt_driver); ++} ++core_initcall(sifive_gemgxl_mgmt_init); diff --git a/target/linux/riscv64/patches/004-spi-sifive.patch b/target/linux/riscv64/patches/004-spi-sifive.patch new file mode 100644 index 0000000000..78f6c3176e --- /dev/null +++ b/target/linux/riscv64/patches/004-spi-sifive.patch @@ -0,0 +1,509 @@ +From 1e23d75040e34fa26cacf715acb23a4344825bc2 Mon Sep 17 00:00:00 2001 +From: "Wesley W. Terpstra" +Date: Mon, 5 Feb 2018 17:42:32 -0800 +Subject: [PATCH] spi-sifive: support SiFive SPI controller in Quad-Mode + +Signed-off-by: Palmer Dabbelt +--- + .../devicetree/bindings/spi/spi-sifive.txt | 29 ++ + drivers/spi/Kconfig | 7 + + drivers/spi/Makefile | 1 + + drivers/spi/spi-sifive.c | 423 ++++++++++++++++++ + 4 files changed, 460 insertions(+) + create mode 100644 Documentation/devicetree/bindings/spi/spi-sifive.txt + create mode 100644 drivers/spi/spi-sifive.c + +diff --git a/Documentation/devicetree/bindings/spi/spi-sifive.txt b/Documentation/devicetree/bindings/spi/spi-sifive.txt +new file mode 100644 +index 0000000000000..945543244601b +--- /dev/null ++++ b/Documentation/devicetree/bindings/spi/spi-sifive.txt +@@ -0,0 +1,29 @@ ++SiFive SPI controller Device Tree Bindings ++------------------------------------------------- ++ ++Required properties: ++- compatible : Should be "sifive,spi0" ++- reg : Physical base address and size of SPI registers map ++ A second (optional) range can indicate memory mapped flash ++- interrupts : Must contain one entry ++- interrupt-parent : Must be core interrupt controller ++- clocks : Must reference the frequency given to the controller ++- #address-cells : Must be '1', indicating which CS to use ++- #size-cells : Must be '0' ++ ++Optional properties: ++- sifive,buffer-size : Depth of hardware queues; defaults to 8 ++- sifive,bits-per-word : Maximum bits per word; defaults to 8 ++ ++Example: ++ spi: spi@10040000 { ++ compatible = "sifive,spi0"; ++ reg = <0x0 0x10040000 0x0 0x1000 0x0 0x20000000 0x0 0x10000000>; ++ interrupt-parent = <&plic>; ++ interrupts = <51>; ++ clocks = <&tlclk>; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ sifive,buffer-size = <8>; ++ sifive,bits-per-word = <8>; ++ }; +diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig +index ad5d68e1dab7c..f77cd28a84392 100644 +--- a/drivers/spi/Kconfig ++++ b/drivers/spi/Kconfig +@@ -736,6 +736,13 @@ config SPI_ZYNQMP_GQSPI + help + Enables Xilinx GQSPI controller driver for Zynq UltraScale+ MPSoC. + ++config SPI_SIFIVE ++ tristate "SiFive SPI controller" ++ depends on HAS_IOMEM ++ select SPI_BITBANG ++ help ++ This exposes the SPI controller IP from SiFive. ++ + # + # Add new SPI master controllers in alphabetical order above this line + # +diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile +index cb1f4378b87c0..5c8e8866b16f8 100644 +--- a/drivers/spi/Makefile ++++ b/drivers/spi/Makefile +@@ -106,6 +106,7 @@ obj-$(CONFIG_SPI_XILINX) += spi-xilinx.o + obj-$(CONFIG_SPI_XLP) += spi-xlp.o + obj-$(CONFIG_SPI_XTENSA_XTFPGA) += spi-xtensa-xtfpga.o + obj-$(CONFIG_SPI_ZYNQMP_GQSPI) += spi-zynqmp-gqspi.o ++obj-$(CONFIG_SPI_SIFIVE) += spi-sifive.o + + # SPI slave protocol handlers + obj-$(CONFIG_SPI_SLAVE_TIME) += spi-slave-time.o +diff --git a/drivers/spi/spi-sifive.c b/drivers/spi/spi-sifive.c +new file mode 100644 +index 0000000000000..208566a9888d7 +--- /dev/null ++++ b/drivers/spi/spi-sifive.c +@@ -0,0 +1,423 @@ ++/* ++ * SiFive SPI controller driver (master mode only) ++ * ++ * Author: SiFive, Inc. ++ * sifive@sifive.com ++ * ++ * 2018 (c) SiFive Software, Inc. ++ ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License version 2 as ++ * published by the Free Software Foundation. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#define SIFIVE_SPI_MAX_CS 32 ++ ++#define SIFIVE_SPI_NAME "sifive_spi" ++ ++#define SIFIVE_SPI_DEFAULT_DEPTH 8 ++#define SIFIVE_SPI_DEFAULT_BITS 8 ++ ++#define XSPI_SCDR_OFFSET 0x000 /* Serial Clock Divisor Register */ ++#define XSPI_SCD_SCALE_MASK 0xFFF ++ ++#define XSPI_SCMR_OFFSET 0x004 /* Serial Clock Mode Register */ ++#define XSPI_SCM_CPHA 1 ++#define XSPI_SCM_CPOL 2 ++#define XSPI_SCM_MODE_MASK (XSPI_SCM_CPHA | XSPI_SCM_CPOL) ++ ++#define XSPI_CSIDR_OFFSET 0x010 ++#define XSPI_CSDR_OFFSET 0x014 ++#define XSPI_CSMR_OFFSET 0x018 ++#define XSPI_CSM_MODE_AUTO 0 ++#define XSPI_CSM_MODE_HOLD 2 ++#define XSPI_CSM_MODE_OFF 3 ++ ++#define XSPI_DC0R_OFFSET 0x028 ++#define XSPI_CS_TO_SCK_MASK 0xFF ++#define XSPI_SCK_TO_CS_MASK (0xFF << 16) ++#define XSPI_DC1R_OFFSET 0x02C ++#define XSPI_MIN_CS_IATIME_MASK 0xFF ++#define XSPI_MAX_IF_DELAY_MASK (0xFF << 16) ++ ++#define XSPI_FFR_OFFSET 0x040 ++#define XSPI_FF_SINGLE 0 ++#define XSPI_FF_DUAL 1 ++#define XSPI_FF_QUAD 2 ++#define XSPI_FF_SPI_MASK 0x3 ++#define XSPI_FF_LSB_FIRST 4 ++#define XSPI_FF_TX_DIR 8 ++#define XSPI_FF_BPF_MASK (0xFF << 16) ++ ++#define XSPI_TXDR_OFFSET 0x048 /* Data Transmit Register */ ++#define XSPI_TXD_FIFO_FULL (8U << 28) ++#define XSPI_RXDR_OFFSET 0x04C /* Data Receive Register */ ++#define XSPI_RXD_FIFO_EMPTY (8U << 28) ++#define XSPI_DATA_MASK 0xFF ++#define XSPI_DATA_SHIFT 8 ++ ++#define XSPI_TXWMR_OFFSET 0x050 /* TX FIFO Watermark Register */ ++#define XSPI_RXWMR_OFFSET 0x054 /* RX FIFO Watermark Register */ ++ ++#define XSPI_FCTRL_OFFSET 0x60 ++ ++#define XSPI_IPR_OFFSET 0x074 /* Interrupt Pendings Register */ ++#define XSPI_IER_OFFSET 0x070 /* Interrupt Enable Register */ ++#define XSPI_TXWM_INTR 0x1 ++#define XSPI_RXWM_INTR 0x2 ++ ++struct sifive_spi { ++ void __iomem *regs; /* virt. address of the control registers */ ++ struct clk *clk; /* bus clock */ ++ int irq; /* watermark irq */ ++ int buffer_size; /* buffer size in words */ ++ u32 cs_inactive; /* Level of the CS pins when inactive*/ ++ struct completion done; /* Wake-up from interrupt */ ++}; ++ ++static void sifive_spi_write(struct sifive_spi *spi, int offset, u32 value) ++{ ++ iowrite32(value, spi->regs + offset); ++} ++ ++static u32 sifive_spi_read(struct sifive_spi *spi, int offset) ++{ ++ return ioread32(spi->regs + offset); ++} ++ ++static void sifive_spi_init(struct sifive_spi *spi) ++{ ++ /* Watermark interrupts are disabled by default */ ++ sifive_spi_write(spi, XSPI_IER_OFFSET, 0); ++ ++ /* Default watermark FIFO threshold values */ ++ sifive_spi_write(spi, XSPI_TXWMR_OFFSET, 1); ++ sifive_spi_write(spi, XSPI_RXWMR_OFFSET, 0); ++ ++ /* Set CS/SCK Delays and Inactive Time to defaults */ ++ ++ /* Exit specialized memory-mapped SPI flash mode */ ++ sifive_spi_write(spi, XSPI_FCTRL_OFFSET, 0); ++} ++ ++static void sifive_spi_prep_device(struct sifive_spi *spi, struct spi_device *device) ++{ ++ u32 cr; ++ ++ /* Update the chip select polarity */ ++ if (device->mode & SPI_CS_HIGH) ++ spi->cs_inactive &= ~BIT(device->chip_select); ++ else ++ spi->cs_inactive |= BIT(device->chip_select); ++ sifive_spi_write(spi, XSPI_CSDR_OFFSET, spi->cs_inactive); ++ ++ /* Select the correct device */ ++ sifive_spi_write(spi, XSPI_CSIDR_OFFSET, device->chip_select); ++ ++ /* Switch clock mode bits */ ++ cr = sifive_spi_read(spi, XSPI_SCMR_OFFSET) & ~XSPI_SCM_MODE_MASK; ++ if (device->mode & SPI_CPHA) ++ cr |= XSPI_SCM_CPHA; ++ if (device->mode & SPI_CPOL) ++ cr |= XSPI_SCM_CPOL; ++ sifive_spi_write(spi, XSPI_SCMR_OFFSET, cr); ++} ++ ++static int sifive_spi_prep_transfer(struct sifive_spi *spi, struct spi_device *device, struct spi_transfer *t) ++{ ++ u32 hz, scale, cr; ++ int mode; ++ ++ /* Calculate and program the clock rate */ ++ hz = t->speed_hz ? t->speed_hz : device->max_speed_hz; ++ scale = (DIV_ROUND_UP(clk_get_rate(spi->clk) >> 1, hz) - 1) & XSPI_SCD_SCALE_MASK; ++ sifive_spi_write(spi, XSPI_SCDR_OFFSET, scale); ++ ++ /* Modify the SPI protocol mode */ ++ cr = sifive_spi_read(spi, XSPI_FFR_OFFSET); ++ ++ /* LSB first? */ ++ cr &= ~XSPI_FF_LSB_FIRST; ++ if (device->mode & SPI_LSB_FIRST) ++ cr |= XSPI_FF_LSB_FIRST; ++ ++ /* SINGLE/DUAL/QUAD? */ ++ mode = max((int)t->rx_nbits, (int)t->tx_nbits); ++ cr &= ~XSPI_FF_SPI_MASK; ++ switch (mode) { ++ case SPI_NBITS_QUAD: cr |= XSPI_FF_QUAD; break; ++ case SPI_NBITS_DUAL: cr |= XSPI_FF_DUAL; break; ++ default: cr |= XSPI_FF_SINGLE; break; ++ } ++ ++ /* SPI direction */ ++ cr &= ~XSPI_FF_TX_DIR; ++ if (!t->rx_buf) ++ cr |= XSPI_FF_TX_DIR; ++ ++ sifive_spi_write(spi, XSPI_FFR_OFFSET, cr); ++ ++ /* We will want to poll if the time we need to wait is less than the context switching time. ++ * Let's call that threshold 5us. The operation will take: ++ * (8/mode) * buffer_size / hz <= 5 * 10^-6 ++ * 1600000 * buffer_size <= hz * mode ++ */ ++ return 1600000 * spi->buffer_size <= hz * mode; ++} ++ ++static void sifive_spi_tx(struct sifive_spi *spi, const u8* tx_ptr) ++{ ++ BUG_ON((sifive_spi_read(spi, XSPI_TXDR_OFFSET) & XSPI_TXD_FIFO_FULL) != 0); ++ sifive_spi_write(spi, XSPI_TXDR_OFFSET, *tx_ptr & XSPI_DATA_MASK); ++} ++ ++static void sifive_spi_rx(struct sifive_spi *spi, u8* rx_ptr) ++{ ++ u32 data = sifive_spi_read(spi, XSPI_RXDR_OFFSET); ++ BUG_ON((data & XSPI_RXD_FIFO_EMPTY) != 0); ++ *rx_ptr = data & XSPI_DATA_MASK; ++} ++ ++static void sifive_spi_wait(struct sifive_spi *spi, int bit, int poll) ++{ ++ if (poll) { ++ u32 cr; ++ do cr = sifive_spi_read(spi, XSPI_IPR_OFFSET); ++ while (!(cr & bit)); ++ } else { ++ reinit_completion(&spi->done); ++ sifive_spi_write(spi, XSPI_IER_OFFSET, bit); ++ wait_for_completion(&spi->done); ++ } ++} ++ ++static void sifive_spi_execute(struct sifive_spi *spi, struct spi_transfer *t, int poll) ++{ ++ int remaining_words = t->len; ++ const u8* tx_ptr = t->tx_buf; ++ u8* rx_ptr = t->rx_buf; ++ ++ while (remaining_words) { ++ int n_words, tx_words, rx_words; ++ n_words = min(remaining_words, spi->buffer_size); ++ ++ /* Enqueue n_words for transmission */ ++ for (tx_words = 0; tx_words < n_words; ++tx_words) ++ sifive_spi_tx(spi, tx_ptr++); ++ ++ if (rx_ptr) { ++ /* Wait for transmission + reception to complete */ ++ sifive_spi_write(spi, XSPI_RXWMR_OFFSET, n_words-1); ++ sifive_spi_wait(spi, XSPI_RXWM_INTR, poll); ++ ++ /* Read out all the data from the RX FIFO */ ++ for (rx_words = 0; rx_words < n_words; ++rx_words) ++ sifive_spi_rx(spi, rx_ptr++); ++ } else { ++ /* Wait for transmission to complete */ ++ sifive_spi_wait(spi, XSPI_TXWM_INTR, poll); ++ } ++ ++ remaining_words -= n_words; ++ } ++} ++ ++static int sifive_spi_transfer_one(struct spi_master *master, struct spi_device *device, struct spi_transfer *t) ++{ ++ struct sifive_spi *spi = spi_master_get_devdata(master); ++ int poll; ++ ++ sifive_spi_prep_device(spi, device); ++ poll = sifive_spi_prep_transfer(spi, device, t); ++ sifive_spi_execute(spi, t, poll); ++ ++ return 0; ++} ++ ++static void sifive_spi_set_cs(struct spi_device *device, bool is_high) ++{ ++ struct sifive_spi *spi = spi_master_get_devdata(device->master); ++ ++ /* Reverse polarity is handled by SCMR/CPOL. Not inverted CS. */ ++ if (device->mode & SPI_CS_HIGH) ++ is_high = !is_high; ++ ++ sifive_spi_write(spi, XSPI_CSMR_OFFSET, is_high ? XSPI_CSM_MODE_AUTO : XSPI_CSM_MODE_HOLD); ++} ++ ++static irqreturn_t sifive_spi_irq(int irq, void *dev_id) ++{ ++ struct sifive_spi *spi = dev_id; ++ u32 ip; ++ ++ ip = sifive_spi_read(spi, XSPI_IPR_OFFSET) & (XSPI_TXWM_INTR | XSPI_RXWM_INTR); ++ if (ip != 0) { ++ /* Disable interrupts until next transfer */ ++ sifive_spi_write(spi, XSPI_IER_OFFSET, 0); ++ complete(&spi->done); ++ return IRQ_HANDLED; ++ } ++ ++ return IRQ_NONE; ++} ++ ++static int sifive_spi_probe(struct platform_device *pdev) ++{ ++ struct sifive_spi *spi; ++ struct resource *res; ++ int ret, num_cs; ++ u32 cs_bits, buffer_size, bits_per_word; ++ struct spi_master *master; ++ ++ master = spi_alloc_master(&pdev->dev, sizeof(struct sifive_spi)); ++ if (!master) { ++ dev_err(&pdev->dev, "out of memory\n"); ++ return -ENOMEM; ++ } ++ ++ spi = spi_master_get_devdata(master); ++ init_completion(&spi->done); ++ platform_set_drvdata(pdev, master); ++ ++ res = platform_get_resource(pdev, IORESOURCE_MEM, 0); ++ spi->regs = devm_ioremap_resource(&pdev->dev, res); ++ if (IS_ERR(spi->regs)) { ++ dev_err(&pdev->dev, "Unable to map IO resources\n"); ++ ret = PTR_ERR(spi->regs); ++ goto put_master; ++ } ++ ++ spi->clk = devm_clk_get(&pdev->dev, NULL); ++ if (IS_ERR(spi->clk)) { ++ dev_err(&pdev->dev, "Unable to find bus clock\n"); ++ ret = PTR_ERR(spi->clk); ++ goto put_master; ++ } ++ ++ spi->irq = platform_get_irq(pdev, 0); ++ if (spi->irq < 0) { ++ dev_err(&pdev->dev, "Unable to find interrupt\n"); ++ ret = spi->irq; ++ goto put_master; ++ } ++ ++ /* Optional parameters */ ++ ret = of_property_read_u32(pdev->dev.of_node, "sifive,buffer-size", &buffer_size); ++ if (ret < 0) ++ spi->buffer_size = SIFIVE_SPI_DEFAULT_DEPTH; ++ else ++ spi->buffer_size = buffer_size; ++ ++ ret = of_property_read_u32(pdev->dev.of_node, "sifive,bits-per-word", &bits_per_word); ++ if (ret < 0) ++ bits_per_word = SIFIVE_SPI_DEFAULT_BITS; ++ ++ /* Spin up the bus clock before hitting registers */ ++ ret = clk_prepare_enable(spi->clk); ++ if (ret) { ++ dev_err(&pdev->dev, "Unable to enable bus clock\n"); ++ goto put_master; ++ } ++ ++ /* probe the number of CS lines */ ++ spi->cs_inactive = sifive_spi_read(spi, XSPI_CSDR_OFFSET); ++ sifive_spi_write(spi, XSPI_CSDR_OFFSET, 0xffffffffU); ++ cs_bits = sifive_spi_read(spi, XSPI_CSDR_OFFSET); ++ sifive_spi_write(spi, XSPI_CSDR_OFFSET, spi->cs_inactive); ++ if (!cs_bits) { ++ dev_err(&pdev->dev, "Could not auto probe CS lines\n"); ++ ret = -EINVAL; ++ goto put_master; ++ } ++ ++ num_cs = ilog2(cs_bits) + 1; ++ if (num_cs > SIFIVE_SPI_MAX_CS) { ++ dev_err(&pdev->dev, "Invalid number of spi slaves\n"); ++ ret = -EINVAL; ++ goto put_master; ++ } ++ ++ /* Define our master */ ++ master->bus_num = pdev->id; ++ master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_LSB_FIRST | SPI_CS_HIGH | ++ SPI_TX_DUAL | SPI_TX_QUAD | SPI_RX_DUAL | SPI_RX_QUAD; ++ master->flags = SPI_CONTROLLER_MUST_TX | SPI_MASTER_GPIO_SS; ++ master->dev.of_node = pdev->dev.of_node; ++ master->bits_per_word_mask = SPI_BPW_MASK(bits_per_word); ++ master->num_chipselect = num_cs; ++ master->transfer_one = sifive_spi_transfer_one; ++ master->set_cs = sifive_spi_set_cs; ++ ++ /* If mmc_spi sees a dma_mask, it starts using dma mapped buffers. ++ * Probably it should rely on the SPI core auto mapping instead. ++ */ ++ pdev->dev.dma_mask = 0; ++ ++ /* Configure the SPI master hardware */ ++ sifive_spi_init(spi); ++ ++ /* Register for SPI Interrupt */ ++ ret = devm_request_irq(&pdev->dev, spi->irq, sifive_spi_irq, 0, ++ dev_name(&pdev->dev), spi); ++ if (ret) { ++ dev_err(&pdev->dev, "Unable to bind to interrupt\n"); ++ goto put_master; ++ } ++ ++ dev_info(&pdev->dev, "mapped; irq=%d, cs=%d\n", ++ spi->irq, master->num_chipselect); ++ ++ ret = devm_spi_register_master(&pdev->dev, master); ++ if (ret < 0) { ++ dev_err(&pdev->dev, "spi_register_master failed\n"); ++ goto put_master; ++ } ++ ++ return 0; ++ ++put_master: ++ spi_master_put(master); ++ ++ return ret; ++} ++ ++static int sifive_spi_remove(struct platform_device *pdev) ++{ ++ struct spi_master *master = platform_get_drvdata(pdev); ++ struct sifive_spi *spi = spi_master_get_devdata(master); ++ ++ /* Disable all the interrupts just in case */ ++ sifive_spi_write(spi, XSPI_IER_OFFSET, 0); ++ spi_master_put(master); ++ ++ return 0; ++} ++ ++static const struct of_device_id sifive_spi_of_match[] = { ++ { .compatible = "sifive,spi0", }, ++ {} ++}; ++MODULE_DEVICE_TABLE(of, sifive_spi_of_match); ++ ++static struct platform_driver sifive_spi_driver = { ++ .probe = sifive_spi_probe, ++ .remove = sifive_spi_remove, ++ .driver = { ++ .name = SIFIVE_SPI_NAME, ++ .of_match_table = sifive_spi_of_match, ++ }, ++}; ++module_platform_driver(sifive_spi_driver); ++ ++MODULE_AUTHOR("SiFive, Inc. "); ++MODULE_DESCRIPTION("SiFive SPI driver"); ++MODULE_LICENSE("GPL"); diff --git a/target/linux/riscv64/patches/005-spi-is25wp256d.patch b/target/linux/riscv64/patches/005-spi-is25wp256d.patch new file mode 100644 index 0000000000..68851b41e2 --- /dev/null +++ b/target/linux/riscv64/patches/005-spi-is25wp256d.patch @@ -0,0 +1,110 @@ +From c6e4a154bd008655dd69a850275d5cb082a7304b Mon Sep 17 00:00:00 2001 +From: "Wesley W. Terpstra" +Date: Mon, 5 Feb 2018 17:44:19 -0800 +Subject: [PATCH] spi-nor: add support for is25wp{32,64,128,256} + +Signed-off-by: Palmer Dabbelt +--- + drivers/mtd/spi-nor/spi-nor.c | 47 ++++++++++++++++++++++++++++++++++- + include/linux/mtd/spi-nor.h | 2 ++ + 2 files changed, 48 insertions(+), 1 deletion(-) + +diff --git a/drivers/mtd/spi-nor/spi-nor.c b/drivers/mtd/spi-nor/spi-nor.c +index d9c368c441948..e9a3557a3c237 100644 +--- a/drivers/mtd/spi-nor/spi-nor.c ++++ b/drivers/mtd/spi-nor/spi-nor.c +@@ -1072,6 +1072,9 @@ static const struct flash_info spi_nor_ids[] = { + SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) }, + { "is25wp128", INFO(0x9d7018, 0, 64 * 1024, 256, + SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) }, ++ { "is25wp256d", INFO(0x9d7019, 0, 32 * 1024, 1024, ++ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) ++ }, + + /* Macronix */ + { "mx25l512e", INFO(0xc22010, 0, 64 * 1024, 1, SECT_4K) }, +@@ -1515,6 +1518,45 @@ static int macronix_quad_enable(struct spi_nor *nor) + return 0; + } + ++/** ++ * issi_unlock() - clear BP[0123] write-protection. ++ * @nor: pointer to a 'struct spi_nor' ++ * ++ * Bits [2345] of the Status Register are BP[0123]. ++ * ISSI chips use a different block protection scheme than other chips. ++ * Just disable the write-protect unilaterally. ++ * ++ * Return: 0 on success, -errno otherwise. ++ */ ++static int issi_unlock(struct spi_nor *nor) ++{ ++ int ret, val; ++ u8 mask = SR_BP0 | SR_BP1 | SR_BP2 | SR_BP3; ++ ++ val = read_sr(nor); ++ if (val < 0) ++ return val; ++ if (!(val & mask)) ++ return 0; ++ ++ write_enable(nor); ++ ++ write_sr(nor, val & ~mask); ++ ++ ret = spi_nor_wait_till_ready(nor); ++ if (ret) ++ return ret; ++ ++ ret = read_sr(nor); ++ if (ret > 0 && !(ret & mask)) { ++ dev_info(nor->dev, "ISSI Block Protection Bits cleared\n"); ++ return 0; ++ } else { ++ dev_err(nor->dev, "ISSI Block Protection Bits not cleared\n"); ++ return -EINVAL; ++ } ++} ++ + /* + * Write status Register and configuration register with 2 bytes + * The first byte will be written to the status register, while the +@@ -2747,6 +2789,9 @@ static int spi_nor_init(struct spi_nor *nor) + spi_nor_wait_till_ready(nor); + } + ++ if (JEDEC_MFR(nor->info) == SNOR_MFR_ISSI) ++ issi_unlock(nor); ++ + if (nor->quad_enable) { + err = nor->quad_enable(nor); + if (err) { +@@ -2926,7 +2971,7 @@ int spi_nor_scan(struct spi_nor *nor, const char *name, + if (ret) + return ret; + +- if (nor->addr_width) { ++ if (nor->addr_width && JEDEC_MFR(info) != SNOR_MFR_ISSI) { + /* already configured from SFDP */ + } else if (info->addr_width) { + nor->addr_width = info->addr_width; +diff --git a/include/linux/mtd/spi-nor.h b/include/linux/mtd/spi-nor.h +index e60da0d34cc14..da422a37d3837 100644 +--- a/include/linux/mtd/spi-nor.h ++++ b/include/linux/mtd/spi-nor.h +@@ -23,6 +23,7 @@ + #define SNOR_MFR_ATMEL CFI_MFR_ATMEL + #define SNOR_MFR_GIGADEVICE 0xc8 + #define SNOR_MFR_INTEL CFI_MFR_INTEL ++#define SNOR_MFR_ISSI 0x9d + #define SNOR_MFR_MICRON CFI_MFR_ST /* ST Micro <--> Micron */ + #define SNOR_MFR_MACRONIX CFI_MFR_MACRONIX + #define SNOR_MFR_SPANSION CFI_MFR_AMD +@@ -121,6 +122,7 @@ + #define SR_BP0 BIT(2) /* Block protect 0 */ + #define SR_BP1 BIT(3) /* Block protect 1 */ + #define SR_BP2 BIT(4) /* Block protect 2 */ ++#define SR_BP3 BIT(5) /* Block protect 3 (on ISSI chips) */ + #define SR_TB BIT(5) /* Top/Bottom protect */ + #define SR_SRWD BIT(7) /* SR write protect */ + /* Spansion/Cypress specific status bits */ diff --git a/target/linux/riscv64/patches/006-uart-sifive-serial-driver.patch b/target/linux/riscv64/patches/006-uart-sifive-serial-driver.patch new file mode 100644 index 0000000000..9779f9f92b --- /dev/null +++ b/target/linux/riscv64/patches/006-uart-sifive-serial-driver.patch @@ -0,0 +1,1128 @@ +From 6f1c41357974f377c4707a9b77125dd9cc9c2873 Mon Sep 17 00:00:00 2001 +From: "Wesley W. Terpstra" +Date: Fri, 16 Mar 2018 11:34:26 -0700 +Subject: [PATCH] serial/sifive: initial driver from Paul Walmsley + +--- + drivers/tty/serial/Kconfig | 23 + + drivers/tty/serial/Makefile | 1 + + drivers/tty/serial/sifive.c | 1051 ++++++++++++++++++++++++++++++ + include/uapi/linux/serial_core.h | 3 + + 4 files changed, 1078 insertions(+) + create mode 100644 drivers/tty/serial/sifive.c + +diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig +index df8bd0c7b97db..94a6de4b7dec4 100644 +--- a/drivers/tty/serial/Kconfig ++++ b/drivers/tty/serial/Kconfig +@@ -1060,6 +1060,29 @@ config SERIAL_OMAP_CONSOLE + your boot loader about how to pass options to the kernel at + boot time.) + ++config SERIAL_SIFIVE ++ tristate "SiFive UART support" ++ depends on OF ++ select SERIAL_CORE ++ help ++ If you have a SiFive Freedom U500 or similar SoC, enable this to ++ support the SiFive UART. ++ ++config SERIAL_SIFIVE_CONSOLE ++ bool "Console on SiFive UART" ++ depends on SERIAL_SIFIVE=y ++ select SERIAL_CORE_CONSOLE ++ help ++ Select this option if you would like to use a SiFive UART as the ++ system console. ++ ++ Even if you say Y here, the currently visible virtual console ++ (/dev/tty0) will still be used as the system console by default, but ++ you can alter that using a kernel command line option such as ++ "console=ttySIx". (Try "man bootparam" or see the documentation of ++ your boot loader about how to pass options to the kernel at ++ boot time.) ++ + config SERIAL_LANTIQ + bool "Lantiq serial driver" + depends on LANTIQ +diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile +index daac675612dff..7e906d3c04558 100644 +--- a/drivers/tty/serial/Makefile ++++ b/drivers/tty/serial/Makefile +@@ -89,6 +89,7 @@ obj-$(CONFIG_SERIAL_MVEBU_UART) += mvebu-uart.o + obj-$(CONFIG_SERIAL_PIC32) += pic32_uart.o + obj-$(CONFIG_SERIAL_MPS2_UART) += mps2-uart.o + obj-$(CONFIG_SERIAL_OWL) += owl-uart.o ++obj-$(CONFIG_SERIAL_SIFIVE) += sifive.o + + # GPIOLIB helpers for modem control lines + obj-$(CONFIG_SERIAL_MCTRL_GPIO) += serial_mctrl_gpio.o +diff --git a/drivers/tty/serial/sifive.c b/drivers/tty/serial/sifive.c +new file mode 100644 +index 0000000000000..588fb31cc94d0 +--- /dev/null ++++ b/drivers/tty/serial/sifive.c +@@ -0,0 +1,1051 @@ ++// SPDX-License-Identifier: GPL-2.0+ ++/* ++ * SiFive UART driver ++ * Copyright (C) 2018 Paul Walmsley ++ * ++ * Based partially on drivers/tty/serial/pxa.c, drivers/pwm/pwm-sifive.c, ++ * and drivers/tty/serial/omap-serial.c ++ * ++ * See Chapter 19 "Universal Asynchronous Receiver/Transmitter (UART)" of ++ * SiFive FE310-G000 v2p3. ++ * ++ * The SiFive UART design is not 8250-compatible. The following common ++ * features are not supported: ++ * - Word lengths other than 8 bits ++ * - Break handling ++ * - Parity ++ * - Flow control ++ * - Modem signals (DSR, RI, etc.) ++ * On the other hand, the design is free from the baggage of the classical 8250 ++ * programming model. ++ * ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License as published by ++ * the Free Software Foundation; either version 2 of the License, or ++ * (at your option) any later version. ++ * ++ * This program is distributed in the hope that it will be useful, ++ * but WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the ++ * GNU General Public License for more details. ++ */ ++ ++/* XXX Magic SYSRQ support - is it possible to implement? */ ++/* XXX ignore_status_mask */ ++/* XXX Ensure operations are spinlocked that need to be spinlocked */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++/* ++ * Register offsets ++ */ ++ ++/* TXDATA */ ++#define SIFIVE_SERIAL_TXDATA_OFFS 0x0 ++#define SIFIVE_SERIAL_TXDATA_FULL_SHIFT 31 ++#define SIFIVE_SERIAL_TXDATA_FULL_MASK (1 << SIFIVE_SERIAL_TXDATA_FULL_SHIFT) ++#define SIFIVE_SERIAL_TXDATA_DATA_SHIFT 0 ++#define SIFIVE_SERIAL_TXDATA_DATA_MASK (0xff << SIFIVE_SERIAL_TXDATA_DATA_SHIFT) ++ ++/* RXDATA */ ++#define SIFIVE_SERIAL_RXDATA_OFFS 0x4 ++#define SIFIVE_SERIAL_RXDATA_EMPTY_SHIFT 31 ++#define SIFIVE_SERIAL_RXDATA_EMPTY_MASK (1 << SIFIVE_SERIAL_RXDATA_EMPTY_SHIFT) ++#define SIFIVE_SERIAL_RXDATA_DATA_SHIFT 0 ++#define SIFIVE_SERIAL_RXDATA_DATA_MASK (0xff << SIFIVE_SERIAL_RXDATA_DATA_SHIFT) ++ ++/* TXCTRL */ ++#define SIFIVE_SERIAL_TXCTRL_OFFS 0x8 ++#define SIFIVE_SERIAL_TXCTRL_TXCNT_SHIFT 16 ++#define SIFIVE_SERIAL_TXCTRL_TXCNT_MASK (0x7 << SIFIVE_SERIAL_TXCTRL_TXCNT_SHIFT) ++#define SIFIVE_SERIAL_TXCTRL_NSTOP_SHIFT 1 ++#define SIFIVE_SERIAL_TXCTRL_NSTOP_MASK (1 << SIFIVE_SERIAL_TXCTRL_NSTOP_SHIFT) ++#define SIFIVE_SERIAL_TXCTRL_TXEN_SHIFT 0 ++#define SIFIVE_SERIAL_TXCTRL_TXEN_MASK (1 << SIFIVE_SERIAL_TXCTRL_TXEN_SHIFT) ++ ++/* RXCTRL */ ++#define SIFIVE_SERIAL_RXCTRL_OFFS 0xC ++#define SIFIVE_SERIAL_RXCTRL_RXCNT_SHIFT 16 ++#define SIFIVE_SERIAL_RXCTRL_RXCNT_MASK (0x7 << SIFIVE_SERIAL_TXCTRL_TXCNT_SHIFT) ++#define SIFIVE_SERIAL_RXCTRL_RXEN_SHIFT 0 ++#define SIFIVE_SERIAL_RXCTRL_RXEN_MASK (1 << SIFIVE_SERIAL_RXCTRL_RXEN_SHIFT) ++ ++/* IE */ ++#define SIFIVE_SERIAL_IE_OFFS 0x10 ++#define SIFIVE_SERIAL_IE_RXWM_SHIFT 1 ++#define SIFIVE_SERIAL_IE_RXWM_MASK (1 << SIFIVE_SERIAL_IE_RXWM_SHIFT) ++#define SIFIVE_SERIAL_IE_TXWM_SHIFT 0 ++#define SIFIVE_SERIAL_IE_TXWM_MASK (1 << SIFIVE_SERIAL_IE_TXWM_SHIFT) ++ ++/* IP */ ++#define SIFIVE_SERIAL_IP_OFFS 0x14 ++#define SIFIVE_SERIAL_IP_RXWM_SHIFT 1 ++#define SIFIVE_SERIAL_IP_RXWM_MASK (1 << SIFIVE_SERIAL_IP_RXWM_SHIFT) ++#define SIFIVE_SERIAL_IP_TXWM_SHIFT 0 ++#define SIFIVE_SERIAL_IP_TXWM_MASK (1 << SIFIVE_SERIAL_IP_TXWM_SHIFT) ++ ++/* DIV */ ++#define SIFIVE_SERIAL_DIV_OFFS 0x18 ++#define SIFIVE_SERIAL_DIV_DIV_SHIFT 0 ++#define SIFIVE_SERIAL_DIV_DIV_MASK (0xffff << SIFIVE_SERIAL_IP_DIV_SHIFT) ++ ++/* ++ * Config macros ++ */ ++ ++/* SIFIVE_SERIAL_MAX_PORTS: maximum number of UARTs possible on a device */ ++/* XXX Move to Kconfig? */ ++#define SIFIVE_SERIAL_MAX_PORTS 10 ++ ++/* SIFIVE_SERIAL_NAME: our driver's name that we pass to the operating system */ ++#define SIFIVE_SERIAL_NAME "sifive-serial" ++ ++/* SIFIVE_TTY_PREFIX: tty name prefix for SiFive serial ports */ ++#define SIFIVE_TTY_PREFIX "ttySI" ++ ++/* ++ * ++ */ ++ ++/** ++ * sifive_serial_port - driver-specific data extension to struct uart_port ++ * @port: struct uart_port embedded in this struct ++ * @dev: struct device * ++ * @ier: shadowed copy of the interrupt enable register ++ * @clkin_rate: input clock to the UART IP block. ++ * @bit_rate: UART serial line rate (e.g., 115200 bps) ++ * @clk_notifier: clock rate change notifier for upstream clock changes ++ */ ++struct sifive_serial_port { ++ struct uart_port port; ++ struct device *dev; ++ unsigned char ier; ++ unsigned long clkin_rate; ++ unsigned long bit_rate; ++ struct clk *clk; ++ struct notifier_block clk_notifier; ++}; ++ ++/* ++ * Structure container-of macros ++ */ ++ ++#define port_to_sifive_serial_port(p) (container_of((p), \ ++ struct sifive_serial_port, \ ++ port)) ++ ++#define notifier_to_sifive_serial_port(nb) (container_of((nb), \ ++ struct sifive_serial_port, \ ++ clk_notifier)) ++ ++/* ++ * Forward declarations ++ */ ++static void sifive_serial_stop_tx(struct uart_port *port); ++ ++/* ++ * Internal functions ++ */ ++ ++/** ++ * sifive_serial_early_write() - write to a UART register (early) ++ * @port: pointer to a struct uart_port record ++ * @offs: register address offset from the IP block base address ++ * @v: value to write to the register ++ * ++ * Given a pointer @port to a struct uart_port record, write the value @v to the ++ * IP block register address offset @offs. This function is intended for early ++ * console use. ++ */ ++static void sifive_serial_early_write(struct uart_port *port, u16 offs, u32 v) ++{ ++ writel(v, port->membase + offs); ++} ++ ++/** ++ * sifive_serial_early_read() - read from a UART register (early) ++ * @port: pointer to a struct uart_port record ++ * @offs: register address offset from the IP block base address ++ * ++ * Given a pointer @port to a struct uart_port record, read the contents of the ++ * IP block register located at offset @offs from the IP block base and return ++ * it. This function is intended for early console use. ++ * ++ * Returns: the register value read from the UART. ++ */ ++static u32 sifive_serial_early_read(struct uart_port *port, u16 offs) ++{ ++ return readl(port->membase + offs); ++} ++ ++/** ++ * sifive_serial_write() - write to a UART register ++ * @ssp: pointer to a struct sifive_serial_port record ++ * @offs: register address offset from the IP block base address ++ * @v: value to write to the register ++ * ++ * Write the value @v to the IP block register located at offset @offs from the ++ * IP block base, given a pointer @ssp to a struct sifive_serial_port record. ++ */ ++static void sifive_serial_write(struct sifive_serial_port *ssp, u16 offs, u32 v) ++{ ++ sifive_serial_early_write(&ssp->port, offs, v); ++} ++ ++/** ++ * sifive_serial_read() - read from a UART register ++ * @ssp: pointer to a struct sifive_serial_port record ++ * @offs: register address offset from the IP block base address ++ * ++ * Read the contents of the IP block register located at offset @offs from the ++ * IP block base, given a pointer @ssp to a struct sifive_serial_port record. ++ * ++ * Returns: the value of the UART register ++ */ ++static u32 sifive_serial_read(struct sifive_serial_port *ssp, u16 offs) ++{ ++ return sifive_serial_early_read(&ssp->port, offs); ++} ++ ++/** ++ * sifive_serial_is_txfifo_full() - is the TXFIFO full? ++ * @ssp: pointer to a struct sifive_serial_port ++ * ++ * Read the transmit FIFO "full" bit, returning a non-zero value if the ++ * TX FIFO is full, or zero if space remains. Intended to be used to prevent ++ * writes to the TX FIFO when it's full. ++ * ++ * Returns: SIFIVE_SERIAL_TXDATA_FULL_MASK (non-zero) if the transmit FIFO ++ * is full, or 0 if space remains. ++ */ ++static int sifive_serial_is_txfifo_full(struct sifive_serial_port *ssp) ++{ ++ return sifive_serial_read(ssp, SIFIVE_SERIAL_TXDATA_OFFS) & ++ SIFIVE_SERIAL_TXDATA_FULL_MASK; ++} ++ ++/** ++ * sifive_serial_transmit_char() - enqueue a byte to transmit onto the TX FIFO ++ * @ssp: pointer to a struct sifive_serial_port ++ * @ch: character to transmit ++ * ++ * Enqueue a byte @ch onto the transmit FIFO, given a pointer @ssp to the ++ * struct sifive_serial_port * to transmit on. Caller should first check to ++ * ensure that the TXFIFO has space; see sifive_serial_is_txfifo_full(). ++ */ ++static void sifive_serial_transmit_char(struct sifive_serial_port *ssp, int ch) ++{ ++ sifive_serial_write(ssp, SIFIVE_SERIAL_TXDATA_OFFS, ch); ++} ++ ++/** ++ * sifive_serial_transmit_chars() - enqueue multiple bytes onto the TX FIFO ++ * @ssp: pointer to a struct sifive_serial_port ++ * ++ * Transfer up to a TX FIFO size's worth of characters from the Linux serial ++ * transmit buffer to the SiFive UART TX FIFO. ++ */ ++static void sifive_serial_transmit_chars(struct sifive_serial_port *ssp) ++{ ++ struct circ_buf *xmit = &ssp->port.state->xmit; ++ int count; ++ ++ if (ssp->port.x_char) { ++ sifive_serial_transmit_char(ssp, ssp->port.x_char); ++ ssp->port.icount.tx++; ++ ssp->port.x_char = 0; ++ return; ++ } ++ if (uart_circ_empty(xmit) || uart_tx_stopped(&ssp->port)) { ++ sifive_serial_stop_tx(&ssp->port); ++ return; ++ } ++ count = ssp->port.fifosize; ++ do { ++ sifive_serial_transmit_char(ssp, xmit->buf[xmit->tail]); ++ xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); ++ ssp->port.icount.tx++; ++ if (uart_circ_empty(xmit)) ++ break; ++ } while (--count > 0); ++ ++ if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) ++ uart_write_wakeup(&ssp->port); ++ ++ if (uart_circ_empty(xmit)) ++ sifive_serial_stop_tx(&ssp->port); ++} ++ ++/** ++ * sifive_serial_enable_txwm() - enable transmit watermark interrupts ++ * @ssp: pointer to a struct sifive_serial_port ++ * ++ * Enable interrupt generation when the transmit FIFO watermark is reached ++ * on the UART referred to by @ssp. ++ */ ++static void sifive_serial_enable_txwm(struct sifive_serial_port *ssp) ++{ ++ if (ssp->ier & SIFIVE_SERIAL_IE_TXWM_MASK) ++ return; ++ ++ ssp->ier |= SIFIVE_SERIAL_IE_TXWM_MASK; ++ sifive_serial_write(ssp, SIFIVE_SERIAL_IE_OFFS, ssp->ier); ++} ++ ++/** ++ * sifive_serial_enable_rxwm() - enable receive watermark interrupts ++ * @ssp: pointer to a struct sifive_serial_port ++ * ++ * Enable interrupt generation when the receive FIFO watermark is reached ++ * on the UART referred to by @ssp. ++ */ ++static void sifive_serial_enable_rxwm(struct sifive_serial_port *ssp) ++{ ++ if (ssp->ier & SIFIVE_SERIAL_IE_RXWM_MASK) ++ return; ++ ++ ssp->ier |= SIFIVE_SERIAL_IE_RXWM_MASK; ++ sifive_serial_write(ssp, SIFIVE_SERIAL_IE_OFFS, ssp->ier); ++} ++ ++/** ++ * sifive_serial_disable_txwm() - disable transmit watermark interrupts ++ * @ssp: pointer to a struct sifive_serial_port ++ * ++ * Disable interrupt generation when the transmit FIFO watermark is reached ++ * on the UART referred to by @ssp. ++ */ ++static void sifive_serial_disable_txwm(struct sifive_serial_port *ssp) ++{ ++ if (!(ssp->ier & SIFIVE_SERIAL_IE_TXWM_MASK)) ++ return; ++ ++ ssp->ier &= ~SIFIVE_SERIAL_IE_TXWM_MASK; ++ sifive_serial_write(ssp, SIFIVE_SERIAL_IE_OFFS, ssp->ier); ++} ++ ++/** ++ * sifive_serial_disable_rxwm() - disable receive watermark interrupts ++ * @ssp: pointer to a struct sifive_serial_port ++ * ++ * Disable interrupt generation when the receive FIFO watermark is reached ++ * on the UART referred to by @ssp. ++ */ ++static void sifive_serial_disable_rxwm(struct sifive_serial_port *ssp) ++{ ++ if (!(ssp->ier & SIFIVE_SERIAL_IE_RXWM_MASK)) ++ return; ++ ++ ssp->ier &= ~SIFIVE_SERIAL_IE_RXWM_MASK; ++ sifive_serial_write(ssp, SIFIVE_SERIAL_IE_OFFS, ssp->ier); ++} ++ ++/** ++ * sifive_serial_receive_char() - receive a byte from the UART ++ * @ssp: pointer to a struct sifive_serial_port ++ * @is_empty: char pointer to return whether the RX FIFO is empty ++ * ++ * Try to read a byte from the SiFive UART RX FIFO, referenced by ++ * @ssp, and to return it. Also returns the RX FIFO empty bit in ++ * the char pointed to by @ch. The caller must pass the byte back to the ++ * Linux serial layer if needed. ++ * ++ * Returns: the byte read from the UART RX FIFO. ++ */ ++static char sifive_serial_receive_char(struct sifive_serial_port *ssp, ++ char *is_empty) ++{ ++ u32 v; ++ u8 ch; ++ ++ v = sifive_serial_read(ssp, SIFIVE_SERIAL_RXDATA_OFFS); ++ ++ if (!is_empty) ++ WARN_ON(1); ++ else ++ *is_empty = (v & SIFIVE_SERIAL_RXDATA_EMPTY_MASK) >> ++ SIFIVE_SERIAL_RXDATA_EMPTY_SHIFT; ++ ++ ch = (v & SIFIVE_SERIAL_RXDATA_DATA_MASK) >> ++ SIFIVE_SERIAL_RXDATA_DATA_SHIFT; ++ ++ return ch; ++} ++ ++/** ++ * sifive_serial_receive_chars() - receive multiple bytes from the UART ++ * @ssp: pointer to a struct sifive_serial_port ++ * ++ * Receive up to an RX FIFO's worth of bytes from the SiFive UART referred ++ * to by @ssp and pass them up to the Linux serial layer. ++ */ ++static void sifive_serial_receive_chars(struct sifive_serial_port *ssp) ++{ ++ unsigned char ch; ++ char is_empty; ++ int c; ++ ++ for (c = ssp->port.fifosize; c > 0; --c) { ++ ch = sifive_serial_receive_char(ssp, &is_empty); ++ if (is_empty) break; ++ ++ ssp->port.icount.rx++; ++ uart_insert_char(&ssp->port, 0, 0, ch, TTY_NORMAL); ++ } ++} ++ ++/** ++ * sifive_serial_update_div() - calculate the divisor setting by the line rate ++ * @ssp: pointer to a struct sifive_serial_port ++ * ++ * Calculate the appropriate value of the clock divisor for the UART ++ * referred to by @ssp and the target line rate referred to by @bps, and ++ * return it. ++ */ ++static void sifive_serial_update_div(struct sifive_serial_port *ssp) ++{ ++ u16 div = DIV_ROUND_UP(ssp->clkin_rate, ssp->bit_rate) - 1; ++ /* XXX check for div out of spec */ ++ sifive_serial_write(ssp, SIFIVE_SERIAL_DIV_OFFS, div); ++} ++ ++/** ++ * sifive_serial_update_bit_rate() - set the UART "baud rate" ++ * @ssp: pointer to a struct sifive_serial_port ++ * @rate: new target bit rate ++ * ++ * Calculate the UART divisor value for the target bit rate @rate for the ++ * SiFive UART described by @ssp and program it into the UART. There may ++ * be some error between the target bit rate and the actual bit rate implemented ++ * by the UART due to clock ratio granularity. ++ */ ++static void sifive_serial_update_bit_rate(struct sifive_serial_port *ssp, ++ unsigned int rate) ++{ ++ if (ssp->bit_rate == rate) ++ return; ++ ++ ssp->bit_rate = rate; ++ sifive_serial_update_div(ssp); ++} ++ ++/** ++ * sifive_serial_set_stop_bits() - set the number of stop bits ++ * @ssp: pointer to a struct sifive_serial_port ++ * @nstop: 1 or 2 (stop bits) ++ * ++ * Program the SiFive UART referred to by @ssp to use @nstop stop bits. ++ */ ++static void sifive_serial_set_stop_bits(struct sifive_serial_port *ssp, ++ char nstop) ++{ ++ u32 v; ++ ++ if (nstop < 1 || nstop > 2) { ++ WARN_ON(1); ++ return; ++ } ++ ++ v = sifive_serial_read(ssp, SIFIVE_SERIAL_TXCTRL_OFFS); ++ v &= ~SIFIVE_SERIAL_TXCTRL_NSTOP_MASK; ++ v |= (nstop-1) << SIFIVE_SERIAL_TXCTRL_NSTOP_SHIFT; ++ sifive_serial_write(ssp, SIFIVE_SERIAL_TXCTRL_OFFS, v); ++} ++ ++/** ++ * sifive_serial_wait_for_xmitr() - wait for an empty slot on the TX FIFO ++ * @ssp: pointer to a struct sifive_serial_port ++ * ++ * Delay while the UART TX FIFO referred to by @ssp is marked as full. ++ * ++ * XXX Probably should use a timeout/bailout. ++ */ ++static inline void sifive_serial_wait_for_xmitr(struct sifive_serial_port *ssp) ++{ ++ while (sifive_serial_is_txfifo_full(ssp)) ++ udelay(1); /* XXX Should vary by bps rate */ ++} ++ ++/* ++ * Linux serial API functions ++ */ ++ ++static void sifive_serial_stop_tx(struct uart_port *port) ++{ ++ struct sifive_serial_port *ssp = port_to_sifive_serial_port(port); ++ ++ sifive_serial_disable_txwm(ssp); ++} ++ ++static void sifive_serial_stop_rx(struct uart_port *port) ++{ ++ struct sifive_serial_port *ssp = port_to_sifive_serial_port(port); ++ ++ sifive_serial_disable_rxwm(ssp); ++} ++ ++static void sifive_serial_start_tx(struct uart_port *port) ++{ ++ struct sifive_serial_port *ssp = port_to_sifive_serial_port(port); ++ ++ sifive_serial_enable_txwm(ssp); ++} ++ ++static irqreturn_t sifive_serial_irq(int irq, void *dev_id) ++{ ++ struct sifive_serial_port *ssp = dev_id; ++ irqreturn_t r = IRQ_NONE; ++ int c = ssp->port.fifosize; ++ u32 ip; ++ ++ spin_lock(&ssp->port.lock); ++ ++ do { ++ ip = sifive_serial_read(ssp, SIFIVE_SERIAL_IP_OFFS); ++ if (!ip) ++ break; ++ ++ r = IRQ_HANDLED; ++ ++ if (ip & SIFIVE_SERIAL_IP_RXWM_MASK) ++ sifive_serial_receive_chars(ssp); ++ if (ip & SIFIVE_SERIAL_IP_TXWM_MASK) ++ sifive_serial_transmit_chars(ssp); ++ } while (c--); ++ ++ spin_unlock(&ssp->port.lock); ++ ++ tty_flip_buffer_push(&ssp->port.state->port); ++ ++ return r; ++} ++ ++static unsigned int sifive_serial_tx_empty(struct uart_port *port) ++{ ++ struct sifive_serial_port *ssp = port_to_sifive_serial_port(port); ++ ++ return !sifive_serial_is_txfifo_full(ssp); ++} ++ ++static unsigned int sifive_serial_get_mctrl(struct uart_port *port) ++{ ++ return 0; /* XXX -EINVAL? */ ++} ++ ++static void sifive_serial_set_mctrl(struct uart_port *port, unsigned int mctrl) ++{ ++ // dev_err(port->dev, "set_mctrl not supported\n"); ++} ++ ++static void sifive_serial_break_ctl(struct uart_port *port, int break_state) ++{ ++ dev_err(port->dev, "sending break not supported\n"); ++} ++ ++static int sifive_serial_startup(struct uart_port *port) ++{ ++ struct sifive_serial_port *ssp = port_to_sifive_serial_port(port); ++ ++ sifive_serial_enable_rxwm(ssp); ++ ++ return 0; ++} ++ ++static void sifive_serial_shutdown(struct uart_port *port) ++{ ++ struct sifive_serial_port *ssp = port_to_sifive_serial_port(port); ++ ++ sifive_serial_disable_rxwm(ssp); ++ sifive_serial_disable_txwm(ssp); ++} ++ ++/** ++ * sifive_serial_clk_notifier() - clock post-rate-change notifier ++ * @nb: pointer to the struct notifier_block, from the notifier code ++ * @event: event mask from the notifier code ++ * @data: pointer to the struct clk_notifier_data from the notifier code ++ * ++ * On the H5U SoC, the UART IP block is derived from the CPU clock source ++ * after a synchronous divide-by-two divider, so any CPU clock rate change ++ * requires the UART baud rate to be updated. This presumably could corrupt any ++ * serial word currently being transmitted or received. It would probably ++ * be better to stop receives and transmits, then complete the baud rate ++ * change, then re-enable them. ++ */ ++static int sifive_serial_clk_notifier(struct notifier_block *nb, ++ unsigned long event, void *data) ++{ ++ struct clk_notifier_data *cnd = data; ++ struct sifive_serial_port *ssp = notifier_to_sifive_serial_port(nb); ++ ++ if (event == POST_RATE_CHANGE && ssp->clkin_rate != cnd->new_rate) { ++ ssp->clkin_rate = cnd->new_rate; ++ sifive_serial_update_div(ssp); ++ } ++ ++ return NOTIFY_OK; ++} ++ ++static void sifive_serial_set_termios(struct uart_port *port, ++ struct ktermios *termios, ++ struct ktermios *old) ++{ ++ struct sifive_serial_port *ssp = port_to_sifive_serial_port(port); ++ int rate; ++ char nstop; ++ ++ if ((termios->c_cflag & CSIZE) != CS8) { ++ dev_err(ssp->port.dev, "only 8-bit words supported\n"); ++ return; ++ } ++ ++ /* Set number of stop bits */ ++ nstop = (termios->c_cflag & CSTOPB) ? 2 : 1; ++ sifive_serial_set_stop_bits(ssp, nstop); ++ ++ /* Set line rate */ ++ rate = uart_get_baud_rate(port, termios, old, 0, ssp->clkin_rate / 16); ++ sifive_serial_update_bit_rate(ssp, rate); ++ ++ /* XXX Enable FIFOs with watermark 1 */ ++ ++#if 0 ++ spin_lock_irqsave(&ssp->port.lock, flags); ++#endif ++ ++ /* ++ * Update the per-port timeout. ++ */ ++ uart_update_timeout(port, termios->c_cflag, rate); ++ ++ /* XXX */ ++ ssp->port.read_status_mask = 0; ++ if (termios->c_iflag & INPCK) { ++ dev_err(ssp->port.dev, "INPCK flag not supported\n"); ++ return; ++ } ++ if (termios->c_iflag & (BRKINT | PARMRK)) { ++ dev_err(ssp->port.dev, "BRKINT/PARMRK flag not supported\n"); ++ return; ++ } ++ ++#if 0 ++ /* ++ * ignore all characters if CREAD is not set ++ */ ++ if ((termios->c_cflag & CREAD) == 0) ++ ssp->port.ignore_status_mask |= UART_LSR_DR; ++#endif ++ ++ /* XXX enable interrupts */ ++} ++ ++static void sifive_serial_release_port(struct uart_port *port) ++{ ++} ++ ++static int sifive_serial_request_port(struct uart_port *port) ++{ ++ return 0; ++} ++ ++static void sifive_serial_config_port(struct uart_port *port, int flags) ++{ ++ struct sifive_serial_port *ssp = port_to_sifive_serial_port(port); ++ ++ ssp->port.type = PORT_SIFIVE_H5U; ++} ++ ++static int sifive_serial_verify_port(struct uart_port *port, ++ struct serial_struct *ser) ++{ ++ return -EINVAL; ++} ++ ++static const char *sifive_serial_type(struct uart_port *port) ++{ ++ return port->type == PORT_SIFIVE_H5U ? SIFIVE_SERIAL_NAME : NULL; ++} ++ ++/* ++ * Polling support ++ */ ++ ++#ifdef CONFIG_CONSOLE_POLL ++ ++static void sifive_serial_poll_put_char(struct uart_port *port, ++ unsigned char ch) ++{ ++ struct sifive_serial_port *ssp = port_to_sifive_serial_port(port); ++ ++ sifive_serial_wait_for_xmitr(ssp); ++ sifive_serial_write(ssp, SIFIVE_SERIAL_TXDATA_OFFS, ch); ++} ++ ++static int sifive_serial_poll_get_char(struct uart_port *port) ++{ ++ struct sifive_serial_port *ssp = port_to_sifive_serial_port(port); ++ char is_empty, ch; ++ ++ ch = sifive_serial_receive_char(ssp, &is_empty); ++ if (is_empty) ++ return NO_POLL_CHAR; ++ ++ return ch; ++} ++ ++#endif /* CONFIG_CONSOLE_POLL */ ++ ++/* ++ * Earlyconsole support ++ */ ++ ++#ifdef CONFIG_SERIAL_EARLYCON ++static void early_sifive_serial_putc(struct uart_port *port, int c) ++{ ++ while (sifive_serial_early_read(port, SIFIVE_SERIAL_TXDATA_OFFS) & ++ SIFIVE_SERIAL_TXDATA_FULL_MASK) ++ cpu_relax(); ++ ++ sifive_serial_early_write(port, SIFIVE_SERIAL_TXDATA_OFFS, c); ++} ++ ++void early_sifive_serial_write(struct console *console, const char *s, ++ unsigned int count) ++{ ++ struct earlycon_device *device = console->data; ++ struct uart_port *port = &device->port; ++ ++ uart_console_write(port, s, count, early_sifive_serial_putc); ++} ++ ++static int __init early_sifive_serial_setup(struct earlycon_device *device, ++ const char *options) ++{ ++ struct uart_port *port = &device->port; ++ ++ if (!(port->membase || port->iobase)) ++ return -ENODEV; ++ ++ device->con->write = early_sifive_serial_write; ++ return 0; ++} ++ ++OF_EARLYCON_DECLARE(sifive, "sifive,freedom-uart", early_sifive_serial_setup); ++#endif /* CONFIG_SERIAL_EARLYCON */ ++ ++/* ++ * Linux console interface ++ */ ++ ++#ifdef CONFIG_SERIAL_SIFIVE_CONSOLE ++ ++static struct sifive_serial_port *sifive_serial_console_ports[SIFIVE_SERIAL_MAX_PORTS]; ++ ++static void sifive_serial_console_putchar(struct uart_port *port, int ch) ++{ ++ struct sifive_serial_port *ssp = port_to_sifive_serial_port(port); ++ ++ sifive_serial_wait_for_xmitr(ssp); ++ sifive_serial_transmit_char(ssp, ch); ++} ++ ++static void sifive_serial_console_write(struct console *co, const char *s, ++ unsigned int count) ++{ ++ struct sifive_serial_port *ssp = sifive_serial_console_ports[co->index]; ++ unsigned long flags; ++ unsigned int ier; ++ int locked = 1; ++ ++ if (!ssp) return; ++ ++ local_irq_save(flags); ++ if (ssp->port.sysrq) ++ locked = 0; ++ else if (oops_in_progress) ++ locked = spin_trylock(&ssp->port.lock); ++ else ++ spin_lock(&ssp->port.lock); ++ ++ ier = sifive_serial_read(ssp, SIFIVE_SERIAL_IE_OFFS); ++ sifive_serial_write(ssp, SIFIVE_SERIAL_IE_OFFS, 0); ++ ++ uart_console_write(&ssp->port, s, count, sifive_serial_console_putchar); ++ ++ sifive_serial_write(ssp, SIFIVE_SERIAL_IE_OFFS, ier); ++ ++ if (locked) ++ spin_unlock(&ssp->port.lock); ++ local_irq_restore(flags); ++} ++ ++static int __init sifive_serial_console_setup(struct console *co, char *options) ++{ ++ struct sifive_serial_port *ssp; ++ int baud = 115200; ++ int bits = 8; ++ int parity = 'n'; ++ int flow = 'n'; ++ ++ ssp = sifive_serial_console_ports[co->index]; ++ if (!ssp) ++ return -ENODEV; ++ ++ if (options) ++ uart_parse_options(options, &baud, &parity, &bits, &flow); ++ ++ return uart_set_options(&ssp->port, co, baud, parity, bits, flow); ++} ++ ++static struct uart_driver sifive_serial_uart_driver; ++ ++static struct console sifive_serial_console = { ++ .name = SIFIVE_TTY_PREFIX, ++ .write = sifive_serial_console_write, ++ .device = uart_console_device, ++ .setup = sifive_serial_console_setup, ++ .flags = CON_PRINTBUFFER, ++ .index = -1, ++ .data = &sifive_serial_uart_driver, ++}; ++ ++static void sifive_serial_add_console_port(struct sifive_serial_port *ssp) ++{ ++ sifive_serial_console_ports[ssp->port.line] = ssp; ++} ++ ++static void sifive_serial_remove_console_port(struct sifive_serial_port *ssp) ++{ ++ sifive_serial_console_ports[ssp->port.line] = 0; ++} ++ ++#define SIFIVE_SERIAL_CONSOLE (&sifive_serial_console) ++ ++#else ++ ++#define SIFIVE_SERIAL_CONSOLE NULL ++ ++static inline void sifive_serial_add_console_port(struct sifive_serial_port *ssp) ++{} ++static void sifive_serial_remove_console_port(struct sifive_serial_port *ssp) ++{} ++ ++#endif ++ ++static const struct uart_ops sifive_serial_uops = { ++ .tx_empty = sifive_serial_tx_empty, ++ .set_mctrl = sifive_serial_set_mctrl, ++ .get_mctrl = sifive_serial_get_mctrl, ++ .stop_tx = sifive_serial_stop_tx, ++ .start_tx = sifive_serial_start_tx, ++ .stop_rx = sifive_serial_stop_rx, ++ .break_ctl = sifive_serial_break_ctl, ++ .startup = sifive_serial_startup, ++ .shutdown = sifive_serial_shutdown, ++ .set_termios = sifive_serial_set_termios, ++ .type = sifive_serial_type, ++ .release_port = sifive_serial_release_port, ++ .request_port = sifive_serial_request_port, ++ .config_port = sifive_serial_config_port, ++ .verify_port = sifive_serial_verify_port, ++#ifdef CONFIG_CONSOLE_POLL ++ .poll_put_char = sifive_serial_poll_put_char, ++ .poll_get_char = sifive_serial_poll_get_char, ++#endif ++}; ++ ++static struct uart_driver sifive_serial_uart_driver = { ++ .owner = THIS_MODULE, ++ .driver_name = SIFIVE_SERIAL_NAME, ++ .dev_name = "ttySI", ++ .nr = SIFIVE_SERIAL_MAX_PORTS, ++ .cons = SIFIVE_SERIAL_CONSOLE, ++}; ++ ++static int sifive_serial_probe(struct platform_device *pdev) ++{ ++ struct sifive_serial_port *ssp; ++ struct resource *mem; ++ struct clk *clk; ++ void __iomem *base; ++ int irq, id, r; ++ ++ irq = platform_get_irq(pdev, 0); ++ if (irq < 0) { ++ dev_err(&pdev->dev, "could not acquire interrupt\n"); ++ return -EPROBE_DEFER; ++ } ++ ++ mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); ++ base = devm_ioremap_resource(&pdev->dev, mem); ++ if (IS_ERR(base)) { ++ dev_err(&pdev->dev, "could not acquire device memory\n"); ++ return PTR_ERR(base); ++ } ++ ++ clk = devm_clk_get(&pdev->dev, NULL); ++ if (IS_ERR(clk)) { ++ dev_err(&pdev->dev, "unable to find controller clock\n"); ++ return PTR_ERR(clk); ++ } ++ ++ id = of_alias_get_id(pdev->dev.of_node, "serial"); ++ if (id < 0) { ++ dev_err(&pdev->dev, "missing aliases entry\n"); ++ return id; ++ } ++ ++#ifdef CONFIG_SERIAL_SIFIVE_CONSOLE ++ if (id > SIFIVE_SERIAL_MAX_PORTS) { ++ dev_err(&pdev->dev, "too many UARTs (%d)\n", id); ++ return -EINVAL; ++ } ++#endif ++ ++ ssp = devm_kzalloc(&pdev->dev, sizeof(*ssp), GFP_KERNEL); ++ if (!ssp) ++ return -ENOMEM; ++ ++ ssp->port.dev = &pdev->dev; ++ ssp->port.type = PORT_SIFIVE_H5U; ++ ssp->port.iotype = UPIO_MEM; ++ ssp->port.irq = irq; ++ ssp->port.fifosize = 8; ++ ssp->port.ops = &sifive_serial_uops; ++ ssp->port.line = id; ++ ssp->port.mapbase = mem->start; ++ ssp->port.membase = base; ++ ssp->dev = &pdev->dev; ++ ssp->clk = clk; ++ ssp->clk_notifier.notifier_call = sifive_serial_clk_notifier; ++ ++ r = clk_notifier_register(ssp->clk, &ssp->clk_notifier); ++ if (r) { ++ dev_err(&pdev->dev, "could not register clock notifier: %d\n", ++ r); ++ goto probe_out1; ++ } ++ ++ /* Setup clock divider */ ++ ssp->clkin_rate = clk_get_rate(ssp->clk); ++ ssp->bit_rate = 115200; ++ sifive_serial_update_div(ssp); ++ ++ platform_set_drvdata(pdev, ssp); ++ ++ /* Enable transmits and set the watermark level to 1 */ ++ sifive_serial_write(ssp, SIFIVE_SERIAL_TXCTRL_OFFS, ++ (1 << SIFIVE_SERIAL_TXCTRL_TXCNT_SHIFT) | ++ SIFIVE_SERIAL_TXCTRL_TXEN_MASK); ++ ++ /* Enable receives and set the watermark level to 0 */ ++ sifive_serial_write(ssp, SIFIVE_SERIAL_RXCTRL_OFFS, ++ (0 << SIFIVE_SERIAL_RXCTRL_RXCNT_SHIFT) | ++ SIFIVE_SERIAL_RXCTRL_RXEN_MASK); ++ ++ r = request_irq(ssp->port.irq, sifive_serial_irq, ssp->port.irqflags, ++ dev_name(&pdev->dev), ssp); ++ if (r) { ++ dev_err(&pdev->dev, "could not attach interrupt: %d\n", r); ++ goto probe_out2; ++ } ++ ++ r = uart_add_one_port(&sifive_serial_uart_driver, &ssp->port); ++ if (r != 0) { ++ dev_err(&pdev->dev, "could not add uart: %d\n", r); ++ goto probe_out3; ++ } ++ ++ sifive_serial_add_console_port(ssp); ++ ++ return 0; ++ ++probe_out3: ++ free_irq(ssp->port.irq, ssp); ++probe_out2: ++ clk_notifier_unregister(ssp->clk, &ssp->clk_notifier); ++probe_out1: ++ return r; ++} ++ ++static int sifive_serial_remove(struct platform_device *dev) ++{ ++ struct sifive_serial_port *ssp = platform_get_drvdata(dev); ++ ++ sifive_serial_remove_console_port(ssp); ++ uart_remove_one_port(&sifive_serial_uart_driver, &ssp->port); ++ free_irq(ssp->port.irq, ssp); ++ clk_notifier_unregister(ssp->clk, &ssp->clk_notifier); ++ ++ return 0; ++} ++ ++static const struct of_device_id sifive_serial_of_match[] = { ++ { .compatible = "sifive,uart0" }, ++ {}, ++}; ++MODULE_DEVICE_TABLE(of, sifive_serial_match); ++ ++static struct platform_driver sifive_serial_platform_driver = { ++ .probe = sifive_serial_probe, ++ .remove = sifive_serial_remove, ++ .driver = { ++ .name = SIFIVE_SERIAL_NAME, ++ .of_match_table = of_match_ptr(sifive_serial_of_match), ++ }, ++}; ++ ++static int __init sifive_serial_init(void) ++{ ++ struct tty_driver *tty_drv; ++ int r; ++ ++ r = uart_register_driver(&sifive_serial_uart_driver); ++ if (r) goto init_out1; ++ ++ tty_drv = sifive_serial_uart_driver.tty_driver; ++ if (!tty_drv) goto init_out2; ++ ++ /* change default terminal settings for SiFive uarts */ ++ tty_drv->init_termios.c_cflag = B115200 | CS8 | CREAD | HUPCL | CLOCAL; ++ tty_drv->init_termios.c_ispeed = 115200; ++ tty_drv->init_termios.c_ospeed = 115200; ++ ++ r = platform_driver_register(&sifive_serial_platform_driver); ++ if (r) goto init_out2; ++ ++ return 0; ++ ++init_out2: ++ uart_unregister_driver(&sifive_serial_uart_driver); ++init_out1: ++ return r; ++} ++ ++static void __exit sifive_serial_exit(void) ++{ ++ platform_driver_unregister(&sifive_serial_platform_driver); ++ uart_unregister_driver(&sifive_serial_uart_driver); ++} ++ ++module_init(sifive_serial_init); ++module_exit(sifive_serial_exit); ++ ++MODULE_DESCRIPTION("SiFive UART serial driver"); ++MODULE_LICENSE("GPL"); ++MODULE_AUTHOR("Paul Walmsley "); +diff --git a/include/uapi/linux/serial_core.h b/include/uapi/linux/serial_core.h +index dce5f9dae1210..86973c3854145 100644 +--- a/include/uapi/linux/serial_core.h ++++ b/include/uapi/linux/serial_core.h +@@ -281,4 +281,7 @@ + /* MediaTek BTIF */ + #define PORT_MTK_BTIF 117 + ++/* SiFive UART */ ++#define PORT_SIFIVE_H5U 118 ++ + #endif /* _UAPILINUX_SERIAL_CORE_H */ diff --git a/target/linux/riscv64/patches/007-gpio-sifive-support-GPIO-on-SiFive-SoCs.patch b/target/linux/riscv64/patches/007-gpio-sifive-support-GPIO-on-SiFive-SoCs.patch new file mode 100644 index 0000000000..ce41ece86f --- /dev/null +++ b/target/linux/riscv64/patches/007-gpio-sifive-support-GPIO-on-SiFive-SoCs.patch @@ -0,0 +1,409 @@ +From 28447771a2dddf9c083e1eefa5848d03e83496c7 Mon Sep 17 00:00:00 2001 +From: "Wesley W. Terpstra" +Date: Wed, 21 Feb 2018 15:43:02 -0800 +Subject: [PATCH 07/11] gpio-sifive: support GPIO on SiFive SoCs + +--- + .../devicetree/bindings/gpio/gpio-sifive.txt | 28 ++ + drivers/gpio/Kconfig | 7 + + drivers/gpio/Makefile | 1 + + drivers/gpio/gpio-sifive.c | 322 +++++++++++++++++++++ + 4 files changed, 358 insertions(+) + create mode 100644 Documentation/devicetree/bindings/gpio/gpio-sifive.txt + create mode 100644 drivers/gpio/gpio-sifive.c + +diff --git a/Documentation/devicetree/bindings/gpio/gpio-sifive.txt b/Documentation/devicetree/bindings/gpio/gpio-sifive.txt +new file mode 100644 +index 00000000..bf41eed8 +--- /dev/null ++++ b/Documentation/devicetree/bindings/gpio/gpio-sifive.txt +@@ -0,0 +1,28 @@ ++SiFive GPIO controller bindings ++ ++Required properties: ++- compatible: ++ - "sifive,gpio0" ++- reg: Physical base address and length of the controller's registers. ++- #gpio-cells : Should be 2 ++ - The first cell is the gpio offset number. ++ - The second cell indicates the polarity of the GPIO ++- gpio-controller : Marks the device node as a GPIO controller. ++- interrupt-controller: Mark the device node as an interrupt controller ++- #interrupt-cells : Should be 2. ++ - The first cell is the GPIO offset number within the GPIO controller. ++ - The second cell is the edge/level to use for interrupt generation. ++- interrupts: Specify the interrupts, one per GPIO ++ ++Example: ++ ++gpio: gpio@10060000 { ++ compatible = "sifive,gpio0"; ++ interrupt-parent = <&plic>; ++ interrupts = <7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22>; ++ reg = <0x0 0x10060000 0x0 0x1000>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ interrupt-controller; ++ #interrupt-cells = <2>; ++}; +diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig +index 4f52c3a8..7755f49e 100644 +--- a/drivers/gpio/Kconfig ++++ b/drivers/gpio/Kconfig +@@ -439,6 +439,13 @@ config GPIO_REG + A 32-bit single register GPIO fixed in/out implementation. This + can be used to represent any register as a set of GPIO signals. + ++config GPIO_SIFIVE ++ bool "SiFive GPIO support" ++ depends on OF_GPIO ++ select GPIOLIB_IRQCHIP ++ help ++ Say yes here to support the GPIO device on SiFive SoCs. ++ + config GPIO_SPEAR_SPICS + bool "ST SPEAr13xx SPI Chip Select as GPIO support" + depends on PLAT_SPEAR +diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile +index c256aff6..244a3696 100644 +--- a/drivers/gpio/Makefile ++++ b/drivers/gpio/Makefile +@@ -111,6 +111,7 @@ obj-$(CONFIG_GPIO_REG) += gpio-reg.o + obj-$(CONFIG_ARCH_SA1100) += gpio-sa1100.o + obj-$(CONFIG_GPIO_SCH) += gpio-sch.o + obj-$(CONFIG_GPIO_SCH311X) += gpio-sch311x.o ++obj-$(CONFIG_GPIO_SIFIVE) += gpio-sifive.o + obj-$(CONFIG_GPIO_SODAVILLE) += gpio-sodaville.o + obj-$(CONFIG_GPIO_SPEAR_SPICS) += gpio-spear-spics.o + obj-$(CONFIG_GPIO_SPRD) += gpio-sprd.o +diff --git a/drivers/gpio/gpio-sifive.c b/drivers/gpio/gpio-sifive.c +new file mode 100644 +index 00000000..6482ebbc +--- /dev/null ++++ b/drivers/gpio/gpio-sifive.c +@@ -0,0 +1,322 @@ ++/* ++ * SiFive GPIO driver ++ * ++ * Copyright (C) 2018 SiFive, Inc. ++ * ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License version 2 as ++ * published by the Free Software Foundation. ++ */ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#define GPIO_INPUT_VAL 0x00 ++#define GPIO_INPUT_EN 0x04 ++#define GPIO_OUTPUT_EN 0x08 ++#define GPIO_OUTPUT_VAL 0x0C ++#define GPIO_RISE_IE 0x18 ++#define GPIO_RISE_IP 0x1C ++#define GPIO_FALL_IE 0x20 ++#define GPIO_FALL_IP 0x24 ++#define GPIO_HIGH_IE 0x28 ++#define GPIO_HIGH_IP 0x2C ++#define GPIO_LOW_IE 0x30 ++#define GPIO_LOW_IP 0x34 ++#define GPIO_OUTPUT_XOR 0x40 ++ ++#define MAX_GPIO 32 ++ ++struct sifive_gpio { ++ raw_spinlock_t lock; ++ void __iomem *base; ++ struct gpio_chip gc; ++ unsigned long enabled; ++ unsigned trigger[MAX_GPIO]; ++ unsigned int irq_parent[MAX_GPIO]; ++ struct sifive_gpio *self_ptr[MAX_GPIO]; ++}; ++ ++static void sifive_assign_bit(void __iomem *ptr, int offset, int value) ++{ ++ // It's frustrating that we are not allowed to use the device atomics ++ // which are GUARANTEED to be supported by this device on RISC-V ++ u32 bit = BIT(offset), old = ioread32(ptr); ++ if (value) ++ iowrite32(old | bit, ptr); ++ else ++ iowrite32(old & ~bit, ptr); ++} ++ ++static int sifive_direction_input(struct gpio_chip *gc, unsigned offset) ++{ ++ struct sifive_gpio *chip = gpiochip_get_data(gc); ++ unsigned long flags; ++ ++ if (offset >= gc->ngpio) ++ return -EINVAL; ++ ++ raw_spin_lock_irqsave(&chip->lock, flags); ++ sifive_assign_bit(chip->base + GPIO_OUTPUT_EN, offset, 0); ++ sifive_assign_bit(chip->base + GPIO_INPUT_EN, offset, 1); ++ raw_spin_unlock_irqrestore(&chip->lock, flags); ++ ++ return 0; ++} ++ ++static int sifive_direction_output(struct gpio_chip *gc, unsigned offset, int value) ++{ ++ struct sifive_gpio *chip = gpiochip_get_data(gc); ++ unsigned long flags; ++ ++ if (offset >= gc->ngpio) ++ return -EINVAL; ++ ++ raw_spin_lock_irqsave(&chip->lock, flags); ++ sifive_assign_bit(chip->base + GPIO_INPUT_EN, offset, 0); ++ sifive_assign_bit(chip->base + GPIO_OUTPUT_VAL, offset, value); ++ sifive_assign_bit(chip->base + GPIO_OUTPUT_EN, offset, 1); ++ raw_spin_unlock_irqrestore(&chip->lock, flags); ++ ++ return 0; ++} ++ ++static int sifive_get_direction(struct gpio_chip *gc, unsigned offset) ++{ ++ struct sifive_gpio *chip = gpiochip_get_data(gc); ++ ++ if (offset >= gc->ngpio) ++ return -EINVAL; ++ ++ return !(ioread32(chip->base + GPIO_OUTPUT_EN) & BIT(offset)); ++} ++ ++static int sifive_get_value(struct gpio_chip *gc, unsigned offset) ++{ ++ struct sifive_gpio *chip = gpiochip_get_data(gc); ++ ++ if (offset >= gc->ngpio) ++ return -EINVAL; ++ ++ return !!(ioread32(chip->base + GPIO_INPUT_VAL) & BIT(offset)); ++} ++ ++static void sifive_set_value(struct gpio_chip *gc, unsigned offset, int value) ++{ ++ struct sifive_gpio *chip = gpiochip_get_data(gc); ++ unsigned long flags; ++ ++ if (offset >= gc->ngpio) ++ return; ++ ++ raw_spin_lock_irqsave(&chip->lock, flags); ++ sifive_assign_bit(chip->base + GPIO_OUTPUT_VAL, offset, value); ++ raw_spin_unlock_irqrestore(&chip->lock, flags); ++} ++ ++static void sifive_set_ie(struct sifive_gpio *chip, int offset) ++{ ++ unsigned long flags; ++ unsigned trigger; ++ ++ raw_spin_lock_irqsave(&chip->lock, flags); ++ trigger = (chip->enabled & BIT(offset)) ? chip->trigger[offset] : 0; ++ sifive_assign_bit(chip->base + GPIO_RISE_IE, offset, trigger & IRQ_TYPE_EDGE_RISING); ++ sifive_assign_bit(chip->base + GPIO_FALL_IE, offset, trigger & IRQ_TYPE_EDGE_FALLING); ++ sifive_assign_bit(chip->base + GPIO_HIGH_IE, offset, trigger & IRQ_TYPE_LEVEL_HIGH); ++ sifive_assign_bit(chip->base + GPIO_LOW_IE, offset, trigger & IRQ_TYPE_LEVEL_LOW); ++ raw_spin_unlock_irqrestore(&chip->lock, flags); ++} ++ ++static int sifive_irq_set_type(struct irq_data *d, unsigned trigger) ++{ ++ struct gpio_chip *gc = irq_data_get_irq_chip_data(d); ++ struct sifive_gpio *chip = gpiochip_get_data(gc); ++ int offset = irqd_to_hwirq(d); ++ ++ if (offset < 0 || offset >= gc->ngpio) ++ return -EINVAL; ++ ++ chip->trigger[offset] = trigger; ++ sifive_set_ie(chip, offset); ++ return 0; ++} ++ ++/* chained_irq_{enter,exit} already mask the parent */ ++static void sifive_irq_mask(struct irq_data *d) { } ++static void sifive_irq_unmask(struct irq_data *d) { } ++ ++static void sifive_irq_enable(struct irq_data *d) ++{ ++ struct gpio_chip *gc = irq_data_get_irq_chip_data(d); ++ struct sifive_gpio *chip = gpiochip_get_data(gc); ++ int offset = irqd_to_hwirq(d) % MAX_GPIO; // must not fail ++ u32 bit = BIT(offset); ++ ++ /* Switch to input */ ++ sifive_direction_input(gc, offset); ++ ++ /* Clear any sticky pending interrupts */ ++ iowrite32(bit, chip->base + GPIO_RISE_IP); ++ iowrite32(bit, chip->base + GPIO_FALL_IP); ++ iowrite32(bit, chip->base + GPIO_HIGH_IP); ++ iowrite32(bit, chip->base + GPIO_LOW_IP); ++ ++ /* Enable interrupts */ ++ assign_bit(offset, &chip->enabled, 1); ++ sifive_set_ie(chip, offset); ++} ++ ++static void sifive_irq_disable(struct irq_data *d) ++{ ++ struct gpio_chip *gc = irq_data_get_irq_chip_data(d); ++ struct sifive_gpio *chip = gpiochip_get_data(gc); ++ int offset = irqd_to_hwirq(d) % MAX_GPIO; // must not fail ++ ++ assign_bit(offset, &chip->enabled, 0); ++ sifive_set_ie(chip, offset); ++} ++ ++static struct irq_chip sifive_irqchip = { ++ .name = "sifive-gpio", ++ .irq_set_type = sifive_irq_set_type, ++ .irq_mask = sifive_irq_mask, ++ .irq_unmask = sifive_irq_unmask, ++ .irq_enable = sifive_irq_enable, ++ .irq_disable = sifive_irq_disable, ++}; ++ ++static void sifive_irq_handler(struct irq_desc *desc) ++{ ++ struct irq_chip *irqchip = irq_desc_get_chip(desc); ++ struct sifive_gpio **self_ptr = irq_desc_get_handler_data(desc); ++ struct sifive_gpio *chip = *self_ptr; ++ int offset = self_ptr - &chip->self_ptr[0]; ++ u32 bit = BIT(offset); ++ ++ chained_irq_enter(irqchip, desc); ++ ++ /* Re-arm the edge triggers so don't miss the next one */ ++ iowrite32(bit, chip->base + GPIO_RISE_IP); ++ iowrite32(bit, chip->base + GPIO_FALL_IP); ++ ++ generic_handle_irq(irq_find_mapping(chip->gc.irq.domain, offset)); ++ ++ /* Re-arm the level triggers after handling to prevent spurious refire */ ++ iowrite32(bit, chip->base + GPIO_HIGH_IP); ++ iowrite32(bit, chip->base + GPIO_LOW_IP); ++ ++ chained_irq_exit(irqchip, desc); ++} ++ ++static int sifive_gpio_probe(struct platform_device *pdev) ++{ ++ struct device *dev = &pdev->dev; ++ struct device_node *node = pdev->dev.of_node; ++ struct sifive_gpio *chip; ++ struct resource *res; ++ int gpio, irq, ret, ngpio; ++ ++ chip = devm_kzalloc(dev, sizeof(*chip), GFP_KERNEL); ++ if (!chip) { ++ dev_err(dev, "out of memory\n"); ++ return -ENOMEM; ++ } ++ ++ res = platform_get_resource(pdev, IORESOURCE_MEM, 0); ++ chip->base = devm_ioremap_resource(dev, res); ++ if (IS_ERR(chip->base)) { ++ dev_err(dev, "failed to allocate device memory\n"); ++ return PTR_ERR(chip->base); ++ } ++ ++ ngpio = of_irq_count(node); ++ if (ngpio >= MAX_GPIO) { ++ dev_err(dev, "too many interrupts\n"); ++ return -EINVAL; ++ } ++ ++ raw_spin_lock_init(&chip->lock); ++ chip->gc.direction_input = sifive_direction_input; ++ chip->gc.direction_output = sifive_direction_output; ++ chip->gc.get_direction = sifive_get_direction; ++ chip->gc.get = sifive_get_value; ++ chip->gc.set = sifive_set_value; ++ chip->gc.base = -1; ++ chip->gc.ngpio = ngpio; ++ chip->gc.label = dev_name(dev); ++ chip->gc.parent = dev; ++ chip->gc.owner = THIS_MODULE; ++ ++ ret = gpiochip_add_data(&chip->gc, chip); ++ if (ret) ++ return ret; ++ ++ /* Disable all GPIO interrupts before enabling parent interrupts */ ++ iowrite32(0, chip->base + GPIO_RISE_IE); ++ iowrite32(0, chip->base + GPIO_FALL_IE); ++ iowrite32(0, chip->base + GPIO_HIGH_IE); ++ iowrite32(0, chip->base + GPIO_LOW_IE); ++ chip->enabled = 0; ++ ++ ret = gpiochip_irqchip_add(&chip->gc, &sifive_irqchip, 0, handle_simple_irq, IRQ_TYPE_NONE); ++ if (ret) { ++ dev_err(dev, "could not add irqchip\n"); ++ gpiochip_remove(&chip->gc); ++ return ret; ++ } ++ ++ chip->gc.irq.num_parents = ngpio; ++ chip->gc.irq.parents = &chip->irq_parent[0]; ++ chip->gc.irq.map = &chip->irq_parent[0]; ++ ++ for (gpio = 0; gpio < ngpio; ++gpio) { ++ irq = platform_get_irq(pdev, gpio); ++ if (irq < 0) { ++ dev_err(dev, "invalid IRQ\n"); ++ gpiochip_remove(&chip->gc); ++ return -ENODEV; ++ } ++ ++ chip->irq_parent[gpio] = irq; ++ chip->self_ptr[gpio] = chip; ++ chip->trigger[gpio] = IRQ_TYPE_LEVEL_HIGH; ++ } ++ ++ for (gpio = 0; gpio < ngpio; ++gpio) { ++ irq = chip->irq_parent[gpio]; ++ irq_set_chained_handler_and_data(irq, sifive_irq_handler, &chip->self_ptr[gpio]); ++ irq_set_parent(irq_find_mapping(chip->gc.irq.domain, gpio), irq); ++ } ++ ++ platform_set_drvdata(pdev, chip); ++ dev_info(dev, "SiFive GPIO chip registered %d GPIOs\n", ngpio); ++ ++ return 0; ++} ++ ++static const struct of_device_id sifive_gpio_match[] = { ++ { ++ .compatible = "sifive,gpio0", ++ }, ++ { }, ++}; ++ ++static struct platform_driver sifive_gpio_driver = { ++ .probe = sifive_gpio_probe, ++ .driver = { ++ .name = "sifive_gpio", ++ .of_match_table = of_match_ptr(sifive_gpio_match), ++ }, ++}; ++builtin_platform_driver(sifive_gpio_driver) +-- +2.7.4 + -- 2.30.2