From f574b535ebee1a94bed87746af68c1b60b53a663 Mon Sep 17 00:00:00 2001 From: =?utf8?q?Kristjan=20Kru=C5=A1i=C4=8D?= Date: Sat, 4 Feb 2023 17:00:57 +0100 Subject: [PATCH] ipq806x: add support for Nokia Airscale AC400i MIME-Version: 1.0 Content-Type: text/plain; charset=utf8 Content-Transfer-Encoding: 8bit Hardware -------- SoC: Qualcomm IPQ8065 RAM: 512 MB DDR3 Flash: 256 MB NAND (Macronix MX30UF2G18AC) (split into 2x128MB) 4 MB SPI-NOR (Macronix MX25U3235F) WLAN: Qualcomm Atheros QCA9984 - 2.4Ghz Qualcomm Atheros QCA9984 - 5Ghz ETH: eth0 - POE (100Mbps in U-Boot, 1000Mbps in OpenWrt) eth1 - (1000Mbps in both) Auto-negotiation broken on both. USB: USB 2.0 LED: 5G, 2.4G, ETH1, ETH2, CTRL, PWR (All support green and red) BTN: Reset Other: SD card slot (non-functional) Serial: 115200bps, near the Ethernet transformers, labeled 9X. Connections from the arrow to the 9X text: [NC] - [TXD] - [GND] - [RXD] - [NC] Installation ------------ 0. Connect to the device Plug your computer into LAN2 (1000Mbps connection required). If you use the LAN1/POE port, set your computer to force a 100Mbps link. Connect to the device via TTL (Serial) 115200n8. Locate the header (or solder pads) labeled 9X, near the Ethernet jacks/transformers. There should be an arrow on the other side of the header marking. The connections should go like this: (from the arrow to the 9X text): NC - TXD - GND - RXD - NC 1. Prepare for installation While the AP is powering up, interrupt the startup process. MAKE SURE TO CHECK YOUR CURRENT PARTITION! If you see: "Current Partition is : partB" or "Need to switch partition from partA to partB", you have to force the device into partA mode, before continuing. This can be done by changing the PKRstCnt to 5 and resetting the device. setenv PKRstCnt 5 saveenv reset After you interrupt the startup process again, you should see: Need to switch partition from partB to partA You can now continue to the next step. If you see: "Current Partition is : partA", you can continue to the next step. 2. Prevent partition switching. To prevent the device from switching partitions, we are going to modify the startup command. set bootcmd "setenv PKRstCnt 0; saveenv; bootipq" setenv 3. First boot Now, we have to boot the OpenWrt intifs. The easiest way to do this is by using Tiny PXE. You can also use the normal U-Boot tftp method. Run "bootp" this will get an IP from the DHCP server and possibly the firmware image. If it doesn't download the firmware image, run "tftpboot". Now run "bootm" to run the image. You might see: "ERROR: new format image overwritten - must RESET the board to recover" this means that the image you are trying to load is too big. Use a smaller image for the initial boot. 4. Install OpenWrt from initfs Once you are booted into OpenWrt, transfer the OpenWrt upgrade image and use sysupgrade to install OpenWrt to the device. Signed-off-by: Kristjan Krušič --- package/boot/uboot-envtools/files/ipq806x | 3 + package/firmware/ipq-wifi/Makefile | 2 + .../ipq806x/base-files/etc/board.d/01_leds | 8 + .../ipq806x/base-files/etc/board.d/02_network | 1 + .../etc/hotplug.d/firmware/11-ath10k-caldata | 8 + .../base-files/lib/upgrade/platform.sh | 1 + .../arch/arm/boot/dts/qcom-ipq8065-ac400i.dts | 318 ++++++++++++++++++ target/linux/ipq806x/image/generic.mk | 14 + 8 files changed, 355 insertions(+) create mode 100644 target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8065-ac400i.dts diff --git a/package/boot/uboot-envtools/files/ipq806x b/package/boot/uboot-envtools/files/ipq806x index 77dfefbcd819..01a86c7b19fc 100644 --- a/package/boot/uboot-envtools/files/ipq806x +++ b/package/boot/uboot-envtools/files/ipq806x @@ -45,6 +45,9 @@ linksys,ea8500) netgear,r7800) ubootenv_add_uci_config "/dev/mtd2" "0x0" "0x040000" "0x20000" ;; +nokia,ac400i) + ubootenv_add_uci_config "/dev/mtd20" "0x0" "0x040000" "0x20000" + ;; qcom,ipq8064-ap148|\ qcom,ipq8064-db149) ubootenv_add_uci_config $(ubootenv_mtdinfo) diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile index 992ecba839a4..b3fbc36d33db 100644 --- a/package/firmware/ipq-wifi/Makefile +++ b/package/firmware/ipq-wifi/Makefile @@ -44,6 +44,7 @@ ALLWIFIBOARDS:= \ glinet_gl-s1300 \ linksys_ea8300 \ linksys_whw03v2 \ + nokia_ac400i \ p2w_r619ac \ pakedge_wr-1 \ qnap_301w \ @@ -146,6 +147,7 @@ $(eval $(call generate-ipq-wifi-package,glinet_gl-ap1300,GL.iNet GL-AP1300)) $(eval $(call generate-ipq-wifi-package,glinet_gl-s1300,GL.iNet GL-S1300)) $(eval $(call generate-ipq-wifi-package,linksys_ea8300,Linksys EA8300)) $(eval $(call generate-ipq-wifi-package,linksys_whw03v2,Linksys WHW03 V2)) +$(eval $(call generate-ipq-wifi-package,nokia_ac400i,Nokia AC400i)) $(eval $(call generate-ipq-wifi-package,p2w_r619ac,P&W R619AC)) $(eval $(call generate-ipq-wifi-package,pakedge_wr-1,Pakedge WR-1)) $(eval $(call generate-ipq-wifi-package,qnap_301w,QNAP 301w)) diff --git a/target/linux/ipq806x/base-files/etc/board.d/01_leds b/target/linux/ipq806x/base-files/etc/board.d/01_leds index 2b259b903614..82ca270dd6b1 100644 --- a/target/linux/ipq806x/base-files/etc/board.d/01_leds +++ b/target/linux/ipq806x/base-files/etc/board.d/01_leds @@ -43,6 +43,14 @@ netgear,xr500) ucidef_set_led_switch "wan" "WAN" "white:wan" "switch0" "0x20" ucidef_set_led_ide "esata" "eSATA" "white:esata" ;; +nokia,ac400i) + ucidef_set_led_wlan "wlan5g" "5G" "green:wlan5g" "wlan0" + ucidef_set_led_wlan "wlan2g" "2.4G" "green:wlan2g" "wlan1" + ucidef_set_led_netdev "eth1" "ETH1" "green:eth1" "eth0" + ucidef_set_led_netdev "eth2" "ETH2" "green:eth2" "eth1" + ucidef_set_led_default "ctrl" "CTRL" "green:ctrl" "0" + ucidef_set_led_default "pwr" "PWR" "green:power" "1" + ;; tplink,ad7200) ucidef_set_led_usbport "usb1" "USB 1" "blue:usb1" "usb1-port1" "usb2-port1" ucidef_set_led_usbport "usb2" "USB 2" "blue:usb3" "usb3-port1" "usb4-port1" diff --git a/target/linux/ipq806x/base-files/etc/board.d/02_network b/target/linux/ipq806x/base-files/etc/board.d/02_network index f38876b69f08..8dd52452b173 100644 --- a/target/linux/ipq806x/base-files/etc/board.d/02_network +++ b/target/linux/ipq806x/base-files/etc/board.d/02_network @@ -85,6 +85,7 @@ tplink,onhub) ucidef_add_switch "switch0" \ "1:lan" "6@eth1" "2:wan" "0@eth0" ;; +nokia,ac400i |\ ubnt,unifi-ac-hd) ucidef_set_interface_lan "eth0 eth1" ;; diff --git a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index a0e2e9d1237b..4c5019cf5bd2 100644 --- a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -52,6 +52,10 @@ case "$FIRMWARE" in CI_UBIPART=art caldata_extract_ubi "ART" 0x1000 0x2f20 ;; + nokia,ac400i) + caldata_extract "0:art" 0x1000 0x2f20 + ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii 0:appsblenv ethaddr) +2) + ;; zyxel,nbg6817) caldata_extract "0:art" 0x1000 0x2f20 ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii 0:appsblenv ethaddr) 1) @@ -84,6 +88,10 @@ case "$FIRMWARE" in CI_UBIPART=art caldata_extract_ubi "ART" 0x5000 0x2f20 ;; + nokia,ac400i) + caldata_extract "0:art" 0x5000 0x2f20 + ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii 0:appsblenv ethaddr) +3) + ;; zyxel,nbg6817) caldata_extract "0:art" 0x5000 0x2f20 ath10k_patch_mac $(mtd_get_mac_ascii 0:appsblenv ethaddr) diff --git a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh index 67ceaab24fb5..5ec4f513bd33 100644 --- a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh @@ -18,6 +18,7 @@ platform_do_upgrade() { netgear,r7500v2 |\ netgear,r7800 |\ netgear,xr500 |\ + nokia,ac400i |\ qcom,ipq8064-ap148 |\ qcom,ipq8064-ap161) nand_do_upgrade "$1" diff --git a/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8065-ac400i.dts b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8065-ac400i.dts new file mode 100644 index 000000000000..7151f8de525b --- /dev/null +++ b/target/linux/ipq806x/files-5.15/arch/arm/boot/dts/qcom-ipq8065-ac400i.dts @@ -0,0 +1,318 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qcom-ipq8065-smb208.dtsi" +#include + +/ { + model = "Nokia AC400i"; + compatible = "nokia,ac400i", "qcom,ipq8065", "qcom,ipq8064"; + + aliases { + mdio-gpio0 = &mdio0; + ethernet0 = &gmac0; + ethernet1 = &gmac1; + + led-boot = &pwr_red; + led-failsafe = &pwr_red; + led-running = &pwr_green; + led-upgrade = &pwr_green; + }; + + chosen { + bootargs-override = " console=ttyMSM0,115200n8 ubi.mtd=ubi root=/dev/ubiblock0_2"; + }; + + keys { + compatible = "gpio-keys"; + pinctrl-0 = <&button_pins>; + pinctrl-names = "default"; + + reset { + label = "reset"; + gpios = <&qcom_pinmux 15 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-0 = <&led_pins>; + pinctrl-names = "default"; + + 5g_red { + label = "red:5g"; + gpios = <&qcom_pinmux 65 GPIO_ACTIVE_HIGH>; + }; + + 5g_green { + label = "green:5g"; + gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>; + }; + + 2g_red { + label = "red:2g"; + gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; + }; + + 2g_green { + label = "green:2g"; + gpios = <&qcom_pinmux 54 GPIO_ACTIVE_HIGH>; + }; + + eth1_red { + label = "red:eth1"; + gpios = <&qcom_pinmux 68 GPIO_ACTIVE_HIGH>; + }; + + eth1_green { + label = "green:eth1"; + gpios = <&qcom_pinmux 22 GPIO_ACTIVE_LOW>; + }; + + eth2_red { + label = "red:eth2"; + gpios = <&qcom_pinmux 67 GPIO_ACTIVE_HIGH>; + }; + + eth2_green { + label = "green:eth2"; + gpios = <&qcom_pinmux 23 GPIO_ACTIVE_LOW>; + }; + + ctrl_red { + label = "red:ctrl"; + gpios = <&qcom_pinmux 55 GPIO_ACTIVE_HIGH>; + }; + + ctrl_green { + label = "green:ctrl"; + gpios = <&qcom_pinmux 56 GPIO_ACTIVE_HIGH>; + }; + + pwr_red: pwr_red { + label = "red:pwr"; + gpios = <&qcom_pinmux 2 GPIO_ACTIVE_LOW>; + }; + + pwr_green: pwr_green { + label = "green:pwr"; + gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&qcom_pinmux { + spi_pins: spi_pins { + mux { + pins = "gpio18", "gpio19"; + function = "gsbi5"; + drive-strength = <10>; + bias-pull-down; + }; + + clk { + pins = "gpio21"; + function = "gsbi5"; + drive-strength = <12>; + bias-pull-down; + }; + + cs { + pins = "gpio20"; + function = "gpio"; + drive-strength = <10>; + bias-pull-up; + }; + }; + + led_pins: led_pins { + mux { + pins = "gpio65", "gpio64", + "gpio53", "gpio54", + "gpio68", "gpio22", + "gpio67", "gpio23", + "gpio55", "gpio56", + "gpio2", "gpio26"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + button_pins: button_pins { + mux { + pins = "gpio15"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + +}; + +&gsbi5 { + qcom,mode = ; + status = "okay"; + + spi4: spi@1a280000 { + status = "okay"; + spi-max-frequency = <50000000>; + + pinctrl-0 = <&spi_pins>; + pinctrl-names = "default"; + + cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>; + + m25p80@0 { + compatible = "jedec,spi-nor"; + #address-cells = <1>; + #size-cells = <1>; + spi-max-frequency = <50000000>; + reg = <0>; + + partitions { + compatible = "qcom,smem-part"; + }; + }; + }; +}; + +&usb3_0 { + status = "okay"; +}; + +&usb3_1 { + status = "okay"; +}; + +&pcie0 { + status = "okay"; + + /delete-property/ pinctrl-0; + /delete-property/ pinctrl-names; + /delete-property/ perst-gpios; + + bridge@0,0 { + reg = <0x00000000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + ranges; + + wifi@1,0 { + compatible = "qcom,ath10k"; + status = "okay"; + reg = <0x00010000 0 0 0 0>; + qcom,ath10k-calibration-variant = "Nokia-AC400i"; + }; + }; +}; + +&pcie1 { + status = "okay"; + + /delete-property/ pinctrl-0; + /delete-property/ pinctrl-names; + /delete-property/ perst-gpios; + + bridge@0,0 { + reg = <0x00000000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + ranges; + + wifi@1,0 { + compatible = "qcom,ath10k"; + status = "okay"; + reg = <0x00010000 0 0 0 0>; + qcom,ath10k-calibration-variant = "Nokia-AC400i"; + }; + }; +}; + +&mdio0 { + status = "okay"; + pinctrl-0 = <&mdio0_pins>; + pinctrl-names = "default"; + + phy0: ethernet-phy@0 { + reg = <0>; + }; + + phy1: ethernet-phy@1 { + reg = <1>; + }; + +}; + +//POE +&gmac0 { + status = "okay"; + qcom,id = <0>; + + pinctrl-0 = <&rgmii2_pins>; + pinctrl-names = "default"; + + mdiobus = <&mdio0>; + phy-handle = <&phy0>; + phy-mode = "rgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +//LAN1 +&gmac1 { + status = "okay"; + qcom,id = <1>; + + mdiobus = <&mdio0>; + phy-handle = <&phy1>; + phy-mode = "rgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&nand { + status = "okay"; + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + + nand@0 { + reg = <0>; + compatible = "qcom,nandcs"; + + nand-ecc-strength = <4>; + nand-bus-width = <8>; + nand-ecc-step-size = <512>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + rootfs@0 { + label = "rootfs"; + reg = <0x0000000 0x4000000>; + }; + + rootfs_1@4000000 { + label = "rootfs_1"; + reg = <0x4000000 0x4000000>; + }; + + cfg@8000000 { + label = "cfg"; + reg = <0x8000000 0x8000000>; + }; + }; + }; +}; + +&adm_dma { + status = "okay"; +}; diff --git a/target/linux/ipq806x/image/generic.mk b/target/linux/ipq806x/image/generic.mk index 91739bc85870..3e9b366c3962 100644 --- a/target/linux/ipq806x/image/generic.mk +++ b/target/linux/ipq806x/image/generic.mk @@ -335,6 +335,20 @@ define Device/netgear_xr500 endef TARGET_DEVICES += netgear_xr500 +define Device/nokia_ac400i + $(call Device/FitImage) + $(call Device/UbiFit) + DEVICE_VENDOR := Nokia + DEVICE_MODEL := AC400i + SOC := qcom-ipq8065 + DEVICE_DTS := qcom-ipq8065-ac400i + BLOCKSIZE := 128k + PAGESIZE := 2048 + BOARD_NAME := ac400i + DEVICE_PACKAGES := ath10k-firmware-qca9984-ct ipq-wifi-nokia-ac400i +endef +TARGET_DEVICES += nokia_ac400i + define Device/qcom_ipq8064-ap148 $(call Device/FitImage) $(call Device/UbiFit) -- 2.30.2