From f103321349182d5fef5a1b846f017db32005da87 Mon Sep 17 00:00:00 2001 From: Dongming Han Date: Wed, 8 Apr 2020 16:43:51 +0800 Subject: [PATCH] ipq40xx: add support for GL.iNet GL-S1300 Specifications: SOC: Qualcomm IPQ4029 (DAKOTA) ARM Quad-Core RAM: 512 MiB FLASH1: 16 MiB NOR - SPI0 FLASH2: 8 GiB eMMC ETH: Qualcomm QCA8075 WLAN1: Qualcomm Atheros QCA4029 2.4GHz 802.11b/g/n 2x2 WLAN2: Qualcomm Atheros QCA4029 5GHz 802.11n/ac W2 2x2 INPUT: Reset, WPS LED: Power, Mesh, WLAN UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1 UART2: On board with BLE module SPI1: On board socket for Zigbee module Install via tftp - NB: need to flash transition image firstly Firstly install transition image: (IPQ40xx) # tftpboot 0x84000000 s1300-factory-to-openwrt.img (IPQ40xx) # sf probe && imgaddr=0x84000000 && source :script Secondly install openwrt sysupgrade bin: (IPQ40xx) # run lf Revert to factory image: (IPQ40xx) # tftpboot 0x84000000 s1300-openwrt-to-factory.img (IPQ40xx) # sf probe && imgaddr=0x84000000 && source :script The kernel and rootfs of factory firmware are on eMMC, and openwrt firmware is on NOR flash. The transition image includes U-boot and partition table, which decides where to load kernel and rootfs. After you firstly install openwrt image, you can switch between factory and openwrt firmware by flashing transition image. Signed-off-by: Dongming Han --- package/firmware/ipq-wifi/Makefile | 2 + .../ipq-wifi/board-glinet_gl-s1300.qca4019 | Bin 0 -> 24276 bytes .../ipq40xx/base-files/etc/board.d/02_network | 3 +- .../etc/hotplug.d/firmware/11-ath10k-caldata | 2 + .../arm/boot/dts/qcom-ipq4029-gl-s1300.dts | 356 ++++++++++++++++++ target/linux/ipq40xx/image/Makefile | 13 + .../901-arm-boot-add-dts-files.patch | 3 +- .../901-arm-boot-add-dts-files.patch | 3 +- 8 files changed, 379 insertions(+), 3 deletions(-) create mode 100644 package/firmware/ipq-wifi/board-glinet_gl-s1300.qca4019 create mode 100644 target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4029-gl-s1300.dts diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile index c86645e2536..4868b75d166 100644 --- a/package/firmware/ipq-wifi/Makefile +++ b/package/firmware/ipq-wifi/Makefile @@ -34,6 +34,7 @@ ALLWIFIBOARDS:= \ engenius_emd1 \ engenius_emr3500 \ ezviz_cs-w3-wd1200g-eup \ + glinet_gl-s1300 \ linksys_ea8300 \ mobipromo_cm520-79f \ qxwlan_e2600ac @@ -106,6 +107,7 @@ $(eval $(call generate-ipq-wifi-package,engenius_eap2200,EnGenius EAP2200)) $(eval $(call generate-ipq-wifi-package,engenius_emd1,EnGenius EMD1)) $(eval $(call generate-ipq-wifi-package,engenius_emr3500,EnGenius EMR3500)) $(eval $(call generate-ipq-wifi-package,ezviz_cs-w3-wd1200g-eup,EZVIZ CS-W3-WD1200G EUP)) +$(eval $(call generate-ipq-wifi-package,glinet_gl-s1300,GL.iNet GL-S1300)) $(eval $(call generate-ipq-wifi-package,linksys_ea8300,Linksys EA8300)) $(eval $(call generate-ipq-wifi-package,mobipromo_cm520-79f,MobiPromo CM520-79F)) $(eval $(call generate-ipq-wifi-package,qxwlan_e2600ac,Qxwlan E2600AC)) diff --git a/package/firmware/ipq-wifi/board-glinet_gl-s1300.qca4019 b/package/firmware/ipq-wifi/board-glinet_gl-s1300.qca4019 new file mode 100644 index 0000000000000000000000000000000000000000..b84e62f825e714ba579484c702c6d18d9fd33f01 GIT binary patch literal 24276 zcmeHPdr%We8t;T)Tt#6*Km;5@2qAGHKwvdOTmmA?BZA8c669FG7l|S-c^URZOOeHh zh%AB-h%6#6bBL5Du81q@xmQYgRadq57rS+jx+=Znw)F1Ss;k56Niv3zAc@2iVZNlN zzy7+v?yr9{naoW8l212<`-N|d4h)F%i%1Ahj08D3IRHwEKeh$H8>XzH!i|~PS-x30 zQoo(q(mX%uu8jejQdVwe!7i*AxDNV}U|Rxq8CmXscui0%3K)OG@Rjqa;@Dj@O zx|z%Nuc{p2Y_JzDSd6%?&%;bce9eLpwS6tqWTOx507LiEkD=A*w5b-;;|^OeE;h5N z$q|;Z9FSn=8w*Q^hgDTisZ* z)R-6nbU0aE0&SsM2cNZIqT_OTSxRb1j4yOOR<<)W5;p5>u7<900?w_=&2?pYsfmIB zor8~Ie6y6wpv=<5u$pi%#KUxHA)sV>X788vu4>;Gv9f^e&S8D6g;nc!c_+EX4fo_X zMV;UjxMVc-?r7R@f>G$0In*L8kK5<9#aT4eo?983&6T)`?{}A-OE|$RT(k2=Z%NaZ zlYS-cd+xU8l}GJn#yEzIcH|z5&1EM!M_%fbHbz%}SmKsFbh)_A|FB1%W5)Z15)mzq zfGzcdK;Bs|eKA78h^ZCXNz-<;#~W(GDfxdV4XM z9;r3W6d?I2w)wqJc*f^_tPT$tFs=^znRHjv<=~~|))JuakrDZm8L>(s_5jWJ0=O*5S zZkpJH#G!G#IB^gfG!cY^qM^J{F?MV;wrlqarYqYUE?&F{!+h=59FXAdn^mx5H}6Yj z-_+ziN6~+?nAS{vUf$HU5UxpyIheEe36uzwWAG-d$Cz`Q6?GC+VR5C{+m5C{+m z5C{+mEMf#!@mC=pv`_e-APKbf{Pjo}Z7D7wF{`e9V07wM|Mb8T&3KFtaIxALi+C3j zQ(q_un7cw?ZoBsk7jas)V(<|FFfUc81|Ln&;X`oj={K9r#5L9{ZQj_hXXx6f=A#Ay zWV2ab*m449E63I;$yLrBh0YIS+NF6S&ofDi~NB7lJ3j&dsi2n1dT zAbJmRGlhgOqG_-cA zuZ{d>CY|BSV=#1|`MK!UIsmM-d+3vN#2t0#xr^x_axxMTqhg*|90`IagApMr*{6;OdW04p(m{Y=7@Ftspg`Sm1g@$2Du zSEr9TjbCr(?y(0)7~vp1lA__(o8s4_@cLLUVRR~$YD-;WV@t8Y1%PWWP15f5ZbsU& zSL4peuQ%{9&966TGFyR8rvohE0`Ct1mT9+= z&)^BV$b}3p{hp*rl`yaTkpxOvWYE(`2E9L#!K3RoU_wX%_QMnqw$Tx4k` zLLfjOu;>s-NlA>?a_N8m`Po0Fa_KRC{ePbP`NtoA_yg4R{Q8%F|LY&0KK%={*~1@1 z=>4BRpLnYE7Yc&|w0%xa{_7{L&6>ax{Cb>+Zp@rEqSv<){CZ=QUSpYZV{1)%eZy?@ z`WADZl`K4dy*LGXs6G71@D4*?n(e$XJ}^?RES4ur{Ktnznw919bctZ(nzBKjFNqR( zj|`|g6mpqF;Ew$!?B;DB4uB44l|}L-32&@leMXThOOy!IgG!Z5CW#mLj{I6#C(n^Y z2pE{d@Eso?plK$PC(Dz^Zm3%nMY7K%>(w_D4YGphNC6)@oR#m#9d6z6;exT7>Q+TD z?DwOQe)ZRia+yRTRF5c{We1}-b6hkd?33-#hBR^qhBP*$ZdM*q=b zpns1t_RNRBbjv-hO0Ee!#E{v?-|yaEC#vwyS)H!vPihmK z@hGRss=Cu#_?2i8E$ez$euL;Jw}6&3+9N$1R^heZCB3{isnxH_wRmM_Pk+hRq8d*5 zs%%Ab{PDnpPTN;(9_r4j3pvc#=d|PQkh~|M+2@FJj`~VbduTPYnD%*fQ$l5Mv5Ukm z`fBgzUkQ$S)=eskT!cTe@($ecY zrRRl}UWJZnr)su;5iDcwpos>03R~h&aY|fvFWLi#m^gvJ0zkmv-!}9&Wv?{s^8a-L z*8=ro0+0Tx41vRgFShbgZ*LZS!++XfczJp8UyyWO-f7F&_v*S~dc{=DJR;|%|)T>trhyaxg{WJ0kai>3qqH7CmsCdh&jK|cJl z4sHdOV(;klj3o#llPSy6VD8`mNRg0tzjgyFfBw&th;TXr82_CD`R^%>UH9Gw|9$#+ z)-KP)tH +#include +#include + +/ { + model = "GL.iNet GL-S1300"; + compatible = "glinet,gl-s1300"; + + aliases { + led-boot = &led_power; + led-failsafe = &led_power; + led-running = &led_power; + led-upgrade = &led_power; + }; + + memory { + device_type = "memory"; + reg = <0x80000000 0x10000000>; + }; + + soc { + rng@22000 { + status = "okay"; + }; + + mdio@90000 { + status = "okay"; + }; + + ess-psgmii@98000 { + status = "okay"; + }; + + tcsr@1949000 { + compatible = "qcom,tcsr"; + reg = <0x1949000 0x100>; + qcom,wifi_glb_cfg = ; + }; + + tcsr@194b000 { + /* select hostmode */ + compatible = "qcom,tcsr"; + reg = <0x194b000 0x100>; + qcom,usb-hsphy-mode-select = ; + status = "okay"; + }; + + ess_tcsr@1953000 { + compatible = "qcom,tcsr"; + reg = <0x1953000 0x1000>; + qcom,ess-interface-select = ; + }; + + tcsr@1957000 { + compatible = "qcom,tcsr"; + reg = <0x1957000 0x100>; + qcom,wifi_noc_memtype_m0_m2 = ; + }; + + usb2@60f8800 { + status = "okay"; + }; + + usb3@8af8800 { + status = "okay"; + }; + + crypto@8e3a000 { + status = "okay"; + }; + + watchdog@b017000 { + status = "okay"; + }; + + ess-switch@c000000 { + status = "okay"; + switch_lan_bmp = <0x18>; + switch_wan_bmp = <0x20>; + }; + + edma@c080000 { + status = "okay"; + }; + }; + + keys { + compatible = "gpio-keys"; + + wps { + label = "wps"; + gpios = <&tlmm 53 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + reset { + label = "reset"; + gpios = <&tlmm 18 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_power: power { + label = "gl-s1300:green:power"; + gpios = <&tlmm 57 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + + mesh { + label = "gl-s1300:green:mesh"; + gpios = <&tlmm 59 GPIO_ACTIVE_HIGH>; + }; + + wlan { + label = "gl-s1300:green:wlan"; + gpios = <&tlmm 60 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "phy0tpt"; + }; + }; +}; + +&vqmmc { + status = "okay"; +}; + +&sdhci { + status = "okay"; + pinctrl-0 = <&sd_pins>; + pinctrl-names = "default"; + cd-gpios = <&tlmm 22 GPIO_ACTIVE_LOW>; + vqmmc-supply = <&vqmmc>; +}; + +&blsp_dma { + status = "okay"; +}; + +&cryptobam { + status = "okay"; +}; + +&blsp1_spi1 { + pinctrl-0 = <&spi_0_pins>; + pinctrl-names = "default"; + status = "okay"; + cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <24000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + SBL1@0 { + label = "SBL1"; + reg = <0x0 0x40000>; + read-only; + }; + + MIBIB@40000 { + label = "MIBIB"; + reg = <0x40000 0x20000>; + read-only; + }; + + QSEE@60000 { + label = "QSEE"; + reg = <0x60000 0x60000>; + read-only; + }; + + CDT@c0000 { + label = "CDT"; + reg = <0xc0000 0x10000>; + read-only; + }; + + DDRPARAMS@d0000 { + label = "DDRPARAMS"; + reg = <0xd0000 0x10000>; + read-only; + }; + + APPSBLENV@e0000 { + label = "APPSBLENV"; + reg = <0xe0000 0x10000>; + read-only; + }; + + APPSBL@f0000 { + label = "APPSBL"; + reg = <0xf0000 0x80000>; + read-only; + }; + + ART@170000 { + label = "ART"; + reg = <0x170000 0x10000>; + read-only; + }; + + firmware@180000 { + compatible = "denx,fit"; + label = "firmware"; + reg = <0x180000 0xe80000>; + }; + }; + }; +}; + +&blsp1_spi2 { + pinctrl-0 = <&spi_1_pins>; + pinctrl-names = "default"; + status = "okay"; + + spidev1: spi@1 { + compatible = "siliconlabs,si3210"; + reg = <0>; + spi-max-frequency = <24000000>; + }; +}; + +&blsp1_uart1 { + pinctrl-0 = <&serial_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&blsp1_uart2 { + pinctrl-0 = <&serial_1_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&tlmm { + serial_pins: serial_pinmux { + mux { + pins = "gpio16", "gpio17"; + function = "blsp_uart0"; + bias-disable; + }; + }; + + serial_1_pins: serial1_pinmux { + mux { + pins = "gpio8", "gpio9", + "gpio10", "gpio11"; + function = "blsp_uart1"; + bias-disable; + }; + }; + + spi_0_pins: spi_0_pinmux { + pinmux { + function = "blsp_spi0"; + pins = "gpio13", "gpio14", "gpio15"; + }; + pinmux_cs { + function = "gpio"; + pins = "gpio12"; + }; + pinconf { + pins = "gpio13", "gpio14", "gpio15"; + drive-strength = <12>; + bias-disable; + }; + pinconf_cs { + pins = "gpio12"; + drive-strength = <2>; + bias-disable; + output-high; + }; + }; + + spi_1_pins: spi_1_pinmux { + mux { + pins = "gpio44", "gpio46", "gpio47"; + function = "blsp_spi1"; + bias-disable; + }; + host_int { + pins = "gpio42"; + function = "gpio"; + input; + }; + cs { + pins = "gpio45"; + function = "gpio"; + bias-pull-up; + }; + wake { + pins = "gpio40"; + function = "gpio"; + output-high; + }; + reset { + pins = "gpio49"; + function = "gpio"; + output-high; + }; + }; + + sd_pins: sd_pins { + pinmux { + function = "sdio"; + pins = "gpio23", "gpio24", "gpio25", "gpio26", + "gpio28", "gpio29", "gpio30", "gpio31"; + drive-strength = <10>; + }; + + pinmux_sd_clk { + function = "sdio"; + pins = "gpio27"; + drive-strength = <16>; + }; + + pinmux_sd7 { + function = "sdio"; + pins = "gpio32"; + drive-strength = <10>; + bias-disable; + }; + }; +}; + +&usb2_hs_phy { + status = "okay"; +}; + +&usb3_hs_phy { + status = "okay"; +}; + +&usb3_ss_phy { + status = "okay"; +}; + +&wifi0 { + status = "okay"; + qcom,ath10k-calibration-variant = "GL-S1300"; +}; + +&wifi1 { + status = "okay"; + qcom,ath10k-calibration-variant = "GL-S1300"; +}; diff --git a/target/linux/ipq40xx/image/Makefile b/target/linux/ipq40xx/image/Makefile index a374c7da473..5336649c3dd 100644 --- a/target/linux/ipq40xx/image/Makefile +++ b/target/linux/ipq40xx/image/Makefile @@ -437,6 +437,19 @@ define Device/glinet_gl-b1300 endef TARGET_DEVICES += glinet_gl-b1300 +define Device/glinet_gl-s1300 + $(call Device/FitImage) + DEVICE_VENDOR := GL.iNet + DEVICE_MODEL := GL-S1300 + SOC := qcom-ipq4029 + KERNEL_SIZE := 4096k + IMAGE_SIZE := 26624k + IMAGES := sysupgrade.bin + IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata + DEVICE_PACKAGES := ipq-wifi-glinet_gl-s1300 kmod-fs-ext4 kmod-mmc kmod-spi-dev +endef +TARGET_DEVICES += glinet_gl-s1300 + define Device/linksys_ea6350v3 # The Linksys EA6350v3 has a uboot bootloader that does not # support either booting lzma kernel images nor booting UBI diff --git a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch index 2ec10071914..fb358ed184d 100644 --- a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -785,11 +785,47 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -785,11 +785,48 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ @@ -54,6 +54,7 @@ Signed-off-by: John Crispin + qcom-ipq4029-ap-303h.dtb \ + qcom-ipq4029-ap-365.dtb \ + qcom-ipq4029-gl-b1300.dtb \ ++ qcom-ipq4029-gl-s1300.dtb \ + qcom-ipq4029-mr33.dtb \ qcom-ipq8064-ap148.dtb \ qcom-msm8660-surf.dtb \ diff --git a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch index 371faa3a093..2db36aa5971 100644 --- a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -837,11 +837,48 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -837,11 +837,49 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ @@ -55,6 +55,7 @@ Signed-off-by: John Crispin + qcom-ipq4029-ap-303h.dtb \ + qcom-ipq4029-ap-365.dtb \ + qcom-ipq4029-gl-b1300.dtb \ ++ qcom-ipq4029-gl-s1300.dtb \ + qcom-ipq4029-mr33.dtb \ qcom-ipq8064-ap148.dtb \ qcom-msm8660-surf.dtb \ -- 2.30.2