From eaf2e32c12655d7fb58e158086a784393dc6f69a Mon Sep 17 00:00:00 2001 From: Sven Eckelmann Date: Mon, 23 Nov 2020 13:41:34 +0100 Subject: [PATCH] ath79: Add support for OpenMesh A60 Device specifications: ====================== * Qualcomm/Atheros QCA9558 ver 1 rev 0 * 720/600/240 MHz (CPU/DDR/AHB) * 128 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 3T3R 2.4 GHz Wi-Fi (11n) * 3T3R 5 GHz Wi-Fi (11ac) * multi-color LED (controlled via red/green/blue GPIOs) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default)) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x ethernet - eth0 + Label: Ethernet 1 + AR8035 ethernet PHY (RGMII) + 10/100/1000 Mbps Ethernet + 802.3af POE + used as WAN interface - eth1 + Label: Ethernet 2 + AR8031 ethernet PHY (SGMII) + 10/100/1000 Mbps Ethernet + used as LAN interface * 1x USB * internal antennas Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 .bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp .bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/.bin Signed-off-by: Sven Eckelmann --- package/boot/uboot-envtools/files/ath79 | 1 + .../linux/ath79/dts/qca9558_openmesh_a60.dts | 8 + .../linux/ath79/dts/qca9558_openmesh_a60.dtsi | 180 ++++++++++++++++++ .../generic/base-files/etc/board.d/02_network | 1 + .../etc/hotplug.d/firmware/11-ath10k-caldata | 1 + .../base-files/lib/upgrade/platform.sh | 1 + target/linux/ath79/image/generic.mk | 10 + 7 files changed, 202 insertions(+) create mode 100644 target/linux/ath79/dts/qca9558_openmesh_a60.dts create mode 100644 target/linux/ath79/dts/qca9558_openmesh_a60.dtsi diff --git a/package/boot/uboot-envtools/files/ath79 b/package/boot/uboot-envtools/files/ath79 index 7b0692e59f..1fc484df52 100644 --- a/package/boot/uboot-envtools/files/ath79 +++ b/package/boot/uboot-envtools/files/ath79 @@ -48,6 +48,7 @@ netgear,wnr2200-16m|\ netgear,wnr612-v2|\ ocedo,koala|\ ocedo,raccoon|\ +openmesh,a60|\ openmesh,mr600-v1|\ openmesh,mr600-v2|\ openmesh,mr900-v1|\ diff --git a/target/linux/ath79/dts/qca9558_openmesh_a60.dts b/target/linux/ath79/dts/qca9558_openmesh_a60.dts new file mode 100644 index 0000000000..473f055b49 --- /dev/null +++ b/target/linux/ath79/dts/qca9558_openmesh_a60.dts @@ -0,0 +1,8 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qca9558_openmesh_a60.dtsi" + +/ { + compatible = "openmesh,a60", "qca,qca9558"; + model = "OpenMesh A60"; +}; diff --git a/target/linux/ath79/dts/qca9558_openmesh_a60.dtsi b/target/linux/ath79/dts/qca9558_openmesh_a60.dtsi new file mode 100644 index 0000000000..9938e5f4c0 --- /dev/null +++ b/target/linux/ath79/dts/qca9558_openmesh_a60.dtsi @@ -0,0 +1,180 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qca955x.dtsi" + +#include +#include + +/ { + chosen { + /delete-property/ bootargs; + }; + + aliases { + serial0 = &uart; + led-boot = &led_status_green; + led-failsafe = &led_status_green; + led-running = &led_status_green; + led-upgrade = &led_status_green; + label-mac-device = ð0; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + linux,code = ; + gpios = <&gpio 17 GPIO_ACTIVE_LOW>; + }; + }; + + leds { + compatible = "gpio-leds"; + + status_blue { + label = "blue:status"; + gpios = <&gpio 13 GPIO_ACTIVE_HIGH>; + }; + + status_red { + label = "red:status"; + gpios = <&gpio 22 GPIO_ACTIVE_HIGH>; + }; + + led_status_green: status_green { + label = "green:status"; + gpios = <&gpio 23 GPIO_ACTIVE_HIGH>; + }; + }; + + watchdog { + compatible = "linux,wdt-gpio"; + gpios = <&gpio 16 GPIO_ACTIVE_LOW>; + hw_algo = "toggle"; + /* hw_margin_ms is actually 300s but driver limits it to 60s */ + hw_margin_ms = <60000>; + always-running; + }; +}; + +&usb_phy1 { + status = "okay"; +}; + +&usb1 { + status = "okay"; +}; + +&spi { + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <40000000>; + + /* partitions are passed via bootloader */ + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x000000 0x040000>; + read-only; + }; + + partition@40000 { + label = "u-boot-env"; + reg = <0x040000 0x010000>; + }; + + partition@50000 { + label = "custom"; + reg = <0x050000 0x060000>; + read-only; + }; + + partition@b0000 { + label = "inactive"; + reg = <0x0b0000 0x7a0000>; + }; + + partition@850000 { + label = "inactive2"; + reg = <0x850000 0x7a0000>; + }; + + art: partition@ff0000 { + label = "ART"; + reg = <0xff0000 0x010000>; + read-only; + }; + }; + }; +}; + +&mdio0 { + status = "okay"; + + phy-mask = <0x6>; + + phy1: ethernet-phy@1 { + reg = <1>; + eee-broken-100tx; + eee-broken-1000t; + }; + + phy2: ethernet-phy@2 { + reg = <2>; + eee-broken-100tx; + eee-broken-1000t; + at803x-override-sgmii-link-check; + }; +}; + +ð0 { + status = "okay"; + + pll-data = <0x82000101 0x80000101 0x80001313>; + + mtd-mac-address = <&art 0x0>; + + phy-mode = "rgmii-id"; + phy-handle = <&phy1>; + + gmac-config { + device = <&gmac>; + rgmii-enabled = <1>; + rxd-delay = <3>; + rxdv-delay = <3>; + txd-delay = <0>; + txen-delay = <0>; + }; +}; + +ð1 { + status = "okay"; + + pll-data = <0x03000101 0x80000101 0x80001313>; + + mtd-mac-address = <&art 0x6>; + + qca955x-sgmii-fixup; + + phy-handle = <&phy2>; +}; + +&wmac { + status = "okay"; + + mtd-cal-data = <&art 0x1000>; + mtd-mac-address = <&art 0x0>; + mtd-mac-address-increment = <2>; +}; + +&pcie0 { + status = "okay"; +}; diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network index 4133b9d7d3..d2b55f0ba6 100644 --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network @@ -170,6 +170,7 @@ ath79_setup_interfaces() comfast,cf-e120a-v3|\ comfast,cf-e314n-v2|\ compex,wpj531-16m|\ + openmesh,a60|\ openmesh,om2p-v4|\ openmesh,om2p-hs-v4|\ plasmacloud,pa300|\ diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 9e4b4496e5..1402c5529a 100644 --- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -98,6 +98,7 @@ case "$FIRMWARE" in caldata_extract "art" 0x5000 0x844 ath10k_patch_mac $(mtd_get_mac_binary art 0xc) ;; + openmesh,a60|\ openmesh,mr1750-v1|\ openmesh,mr1750-v2) caldata_extract "ART" 0x5000 0x844 diff --git a/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh b/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh index f8b1c13677..9b6a0cf9bc 100644 --- a/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh +++ b/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh @@ -65,6 +65,7 @@ platform_do_upgrade() { jjplus,ja76pf2) redboot_fis_do_upgrade "$1" linux ;; + openmesh,a60|\ openmesh,mr600-v1|\ openmesh,mr600-v2|\ openmesh,mr900-v1|\ diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk index 2e23e4e72c..7c26f5dc1f 100644 --- a/target/linux/ath79/image/generic.mk +++ b/target/linux/ath79/image/generic.mk @@ -1628,6 +1628,16 @@ define Device/openmesh_common_256k openmesh-image ce_type=$$$$(OPENMESH_CE_TYPE) | append-metadata endef +define Device/openmesh_a60 + $(Device/openmesh_common_64k) + SOC := qca9558 + DEVICE_MODEL := A60 + DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct kmod-usb2 + OPENMESH_CE_TYPE := A60 + SUPPORTED_DEVICES += a60 +endef +TARGET_DEVICES += openmesh_a60 + define Device/openmesh_mr600-v1 $(Device/openmesh_common_64k) SOC := ar9344 -- 2.30.2