From e658eee81387c16d7e1de13e0eb0678014139ad0 Mon Sep 17 00:00:00 2001 From: =?utf8?q?Andreas=20B=C3=B6hler?= Date: Mon, 10 Jul 2023 11:55:30 +0200 Subject: [PATCH] ipq4019: add support for ZTE MF287 Pro aka DreiNeo Pro MIME-Version: 1.0 Content-Type: text/plain; charset=utf8 Content-Transfer-Encoding: 8bit The ZTE MF287 Pro is a LTE router used (exclusively?) by the network operator "3". It is very similar to the MF287+, but the hardware layout and partition layout have changed quite a bit. Specifications ============== SoC: IPQ4018 RAM: 256MiB Flash: 8MiB SPI-NOR + 128MiB SPI-NAND LAN: 4x GBit LAN LTE: ZTE Cat12 WiFi: 802.11a/b/g/n/ac SoC-integrated USB: 1x 2.0 MAC addresses ============= LAN: from config + 2 WiFi 1: from config WiFi 2: from config + 1 Installation ============ Option 1 - TFTP --------------- TFTP installation using UART is preferred. Disassemble the device and connect serial. Put the initramfs image as openwrt.bin to your TFTP server and configure a static IP of 192.168.1.100. Load the initramfs image by typing: setenv serverip 192.168.1.100 setenv ipaddr 192.168.1.1 tftpboot 0x82000000 openwrt.bin bootm 0x82000000 From this intiramfs boot you can take a backup of the currently installed partitions as no vendor firmware is available for download: ubiattach -m17 cat /dev/ubi0_0 > /tmp/ubi0_0 cat /dev/ubi0_1 > /tmp/ubi0_1 Copy the files /tmp/ubi0_0 and /tmp/ubi0_1 somewhere save. Once booted, transfer the sysupgrade image and run sysupgrade. You might have to delete the stock volumes first: ubirmvol /dev/ubi0 -N ubi_rootfs ubirmvol /dev/ubi0 -N kernel Option 2 - From stock firmware ------------------------------ The installation from stock requires an exploit first. The exploit consists of a backup file that forces the firmware to download telnetd via TFTP from 192.168.0.22 and run it. Once exploited, you can connect via telnet and login as admin:admin. The exploit will be available at the device wiki page. Once inside the stock firmware, you can transfer the -factory.bin file to /tmp by using "scp" from the stock frmware or "tftp". ZTE has blocked writing to the NAND. Fortunately, it's easy to allow write access - you need to read from one file in /proc. Once done, you need to erase the UBI partition and flash OpenWrt. Before performing the operation, make sure that mtd13 is the partition labelled "rootfs" by calling "cat /proc/mtd". Complete commands: cd /tmp tftp -g -r factory.bin 192.168.0.22 cat /proc/driver/sensor_id flash_erase /dev/mtd17 0 0 dd if=/tmp/factory.bin of=/dev/mtdblock17 bs=131072 Afterwards, reboot your device and you should have a working OpenWrt installation. Restore Stock ============= Option 1 - via UART ------------------- Boot an OpenWrt initramfs image via TFTP as for the initial installation. Transfer the two backed-up files to your box to /tmp. Then, run the following commands - replace $kernel_length and $rootfs_size by the size of ubi0_0 and ubi0_1 in bytes. ubiattach -m 17 ubirmvol /dev/ubi0 -N kernel ubirmvol /dev/ubi0 -N rootfs ubirmvol /dev/ubi0 -N rootfs_data ubimkvol /dev/ubi0 -N kernel -s $kernel_length ubimkvol /dev/ubi0 -N ubi_rootfs -s $rootfs_size ubiupdatevol /dev/ubi0_0 /tmp/ubi0_0 ubiupdatevol /dev/ubi0_1 /tmp/ubi0_1 Option 2 - from within OpenWrt ------------------------------ This option requires to flash an initramfs version first so that access to the flash is possible. This can be achieved by sysupgrading to the recovery.bin version and rebooting. Once rebooted, you are again in a default OpenWrt installation, but no partition is mounted. Follow the commands from Option 1 to flash back to stock. LTE Modem ========= The LTE modem is similar to other ZTE devices and controls some more LEDs and battery management. Configuring the connection using uqmi works properly, the modem provides three serial ports and a QMI CDC ethernet interface. Other Notes =========== Contrary to the stock firmware, the USB port on the back can be used. There is one GPIO Switch "Power button blocker" which, if enabled, does not trigger a reset of the SoC if the modem reboots. If disabled, the SoC is rebooted along with the modem. The modem can be rebooted via the exported GPIO "modem-reset" in /sys/class/gpio. Signed-off-by: Andreas Böhler (cherry picked from commit edfe91372adfdaf5ee4e294fb0f5860a16adc551) --- .../ipq40xx/base-files/etc/board.d/02_network | 3 +- .../base-files/etc/board.d/03_gpio_switches | 1 + .../base-files/lib/upgrade/platform.sh | 2 + .../arch/arm/boot/dts/qcom-ipq4018-mf287.dtsi | 183 ++++++++++++ .../arm/boot/dts/qcom-ipq4018-mf287plus.dts | 180 +----------- .../arm/boot/dts/qcom-ipq4018-mf287pro.dts | 265 ++++++++++++++++++ target/linux/ipq40xx/image/generic.mk | 21 +- 7 files changed, 476 insertions(+), 179 deletions(-) create mode 100644 target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-mf287.dtsi create mode 100644 target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-mf287pro.dts diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network index c297566dd8..77dc892d07 100644 --- a/target/linux/ipq40xx/base-files/etc/board.d/02_network +++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network @@ -108,7 +108,8 @@ ipq40xx_setup_interfaces() zte,mf286d) ucidef_set_interfaces_lan_wan "lan2 lan3 lan4" "wan" ;; - zte,mf287plus) + zte,mf287plus|\ + zte,mf287pro) ucidef_set_interface_lan "lan1 lan2 lan3 lan4" ucidef_set_interface "wan" device "/dev/cdc-wdm0" protocol "qmi" ;; diff --git a/target/linux/ipq40xx/base-files/etc/board.d/03_gpio_switches b/target/linux/ipq40xx/base-files/etc/board.d/03_gpio_switches index f76fe9402d..2035d84993 100644 --- a/target/linux/ipq40xx/base-files/etc/board.d/03_gpio_switches +++ b/target/linux/ipq40xx/base-files/etc/board.d/03_gpio_switches @@ -36,6 +36,7 @@ wallys,dr40x9) ucidef_add_gpio_switch "sim_card_select" "SIM card select" "423" "0" ;; zte,mf286d|\ +zte,mf287pro|\ zte,mf289f) ucidef_add_gpio_switch "power_btn_block" "Power button blocker" "421" "0" ;; diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh index 8807f844e5..83aac330ca 100644 --- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh @@ -28,6 +28,7 @@ EOF zte,mf18a |\ zte,mf286d |\ zte,mf287plus |\ + zte,mf287pro |\ zte,mf289f) CI_UBIPART="rootfs" local mtdnum="$( find_mtd_index $CI_UBIPART )" @@ -211,6 +212,7 @@ platform_do_upgrade() { zte,mf18a |\ zte,mf286d |\ zte,mf287plus |\ + zte,mf287pro |\ zte,mf289f) CI_UBIPART="rootfs" nand_do_upgrade "$1" diff --git a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-mf287.dtsi b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-mf287.dtsi new file mode 100644 index 0000000000..3cbe2eaa38 --- /dev/null +++ b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-mf287.dtsi @@ -0,0 +1,183 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +// Copyright (c) 2022, Pawel Dembicki . +// Copyright (c) 2022, Giammarco Marzano . +// Copyright (c) 2023, Andreas Böhler + +#include "qcom-ipq4019.dtsi" +#include +#include +#include +#include + +/ { + aliases { + led-boot = &led_status; + led-failsafe = &led_status; + led-running = &led_status; + led-upgrade = &led_status; + }; + + chosen { + /* + * bootargs forced by u-boot bootipq command: + * 'ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait' + */ + bootargs-append = " root=/dev/ubiblock0_1"; + }; + + leds { + compatible = "gpio-leds"; + + led_status: led-0 { + label = "blue:power"; + function = LED_FUNCTION_POWER; + color = ; + }; + }; + + keys { + compatible = "gpio-keys"; + + key_reset: key-reset { + label = "reset"; + linux,code = ; + }; + + key_wps: key-wps { + label = "wps"; + linux,code = ; + }; + }; + + soc { + rng@22000 { + status = "okay"; + }; + + tcsr@1949000 { + compatible = "qcom,tcsr"; + reg = <0x1949000 0x100>; + qcom,wifi_glb_cfg = ; + }; + + tcsr@194b000 { + /* select hostmode */ + compatible = "qcom,tcsr"; + reg = <0x194b000 0x100>; + qcom,usb-hsphy-mode-select = ; + status = "okay"; + }; + + ess_tcsr@1953000 { + compatible = "qcom,tcsr"; + reg = <0x1953000 0x1000>; + qcom,ess-interface-select = ; + }; + + tcsr@1957000 { + compatible = "qcom,tcsr"; + reg = <0x1957000 0x100>; + qcom,wifi_noc_memtype_m0_m2 = ; + }; + }; +}; + +&mdio { + status = "okay"; +}; + +&watchdog { + status = "okay"; +}; + +&blsp_dma { + status = "okay"; +}; + +&usb2 { + status = "okay"; +}; + +&usb3 { + status = "okay"; +}; + +&blsp1_uart1 { + pinctrl-0 = <&serial_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&crypto { + status = "okay"; +}; + +&cryptobam { + status = "okay"; +}; + +&gmac { + status = "okay"; + nvmem-cell-names = "mac-address"; + nvmem-cells = <&macaddr_mac_0>; + mac-address-increment = <2>; +}; + +&switch { + status = "okay"; +}; + +&swport2 { + status = "okay"; + + label = "lan1"; +}; + +&swport3 { + status = "okay"; + + label = "lan2"; +}; + +&swport4 { + status = "okay"; + + label = "lan3"; +}; + +&swport5 { + status = "okay"; + + label = "lan4"; +}; + +&qpic_bam { + status = "okay"; +}; + +&usb2_hs_phy { + status = "okay"; +}; + +&usb3_ss_phy { + status = "okay"; +}; + +&usb3_hs_phy { + status = "okay"; +}; + +&wifi0 { + status = "okay"; + nvmem-cell-names = "pre-calibration", "mac-address"; + nvmem-cells = <&precal_art_1000>, <&macaddr_mac_0>; + qcom,ath10k-calibration-variant = "zte,mf287plus"; +}; + +&wifi1 { + status = "okay"; + nvmem-cell-names = "pre-calibration", "mac-address"; + nvmem-cells = <&precal_art_5000>, <&macaddr_mac_0>; + mac-address-increment = <1>; + qcom,ath10k-calibration-variant = "zte,mf287plus"; +}; diff --git a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-mf287plus.dts b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-mf287plus.dts index 6c285f4b8a..db8c8c9ad0 100644 --- a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-mf287plus.dts +++ b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-mf287plus.dts @@ -3,31 +3,12 @@ // Copyright (c) 2022, Giammarco Marzano . // Copyright (c) 2023, Andreas Böhler -#include "qcom-ipq4019.dtsi" -#include -#include -#include -#include +#include "qcom-ipq4018-mf287.dtsi" / { model = "ZTE MF287Plus"; compatible = "zte,mf287plus"; - aliases { - led-boot = &led_status; - led-failsafe = &led_status; - led-running = &led_status; - led-upgrade = &led_status; - }; - - chosen { - /* - * bootargs forced by u-boot bootipq command: - * 'ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait' - */ - bootargs-append = " root=/dev/ubiblock0_1"; - }; - /* * This node is used to restart modem module to avoid anomalous * behaviours on initial communication. @@ -36,85 +17,18 @@ compatible = "gpio-restart"; gpios = <&tlmm 5 GPIO_ACTIVE_HIGH>; }; - - leds { - compatible = "gpio-leds"; - - led_status: led-0 { - label = "blue:power"; - function = LED_FUNCTION_POWER; - color = ; - gpios = <&tlmm 0 GPIO_ACTIVE_LOW>; - }; - }; - - keys { - compatible = "gpio-keys"; - - key-reset { - label = "reset"; - linux,code = ; - gpios = <&tlmm 63 GPIO_ACTIVE_LOW>; - }; - - key-wps { - label = "wps"; - linux,code = ; - gpios = <&tlmm 2 GPIO_ACTIVE_LOW>; - }; - }; - - soc { - rng@22000 { - status = "okay"; - }; - - tcsr@1949000 { - compatible = "qcom,tcsr"; - reg = <0x1949000 0x100>; - qcom,wifi_glb_cfg = ; - }; - - tcsr@194b000 { - /* select hostmode */ - compatible = "qcom,tcsr"; - reg = <0x194b000 0x100>; - qcom,usb-hsphy-mode-select = ; - status = "okay"; - }; - - ess_tcsr@1953000 { - compatible = "qcom,tcsr"; - reg = <0x1953000 0x1000>; - qcom,ess-interface-select = ; - }; - - tcsr@1957000 { - compatible = "qcom,tcsr"; - reg = <0x1957000 0x100>; - qcom,wifi_noc_memtype_m0_m2 = ; - }; - }; }; -&mdio { - status = "okay"; +&key_reset { + gpios = <&tlmm 63 GPIO_ACTIVE_LOW>; }; -&watchdog { - status = "okay"; +&key_wps { + gpios = <&tlmm 2 GPIO_ACTIVE_LOW>; }; -&blsp_dma { - status = "okay"; -}; - -&usb2 { - status = "okay"; -}; - -&usb3 { - status = "okay"; +&led_status { + gpios = <&tlmm 0 GPIO_ACTIVE_LOW>; }; &blsp1_spi1 { @@ -276,59 +190,6 @@ }; }; -&blsp1_uart1 { - pinctrl-0 = <&serial_pins>; - pinctrl-names = "default"; - status = "okay"; -}; - -&crypto { - status = "okay"; -}; - -&cryptobam { - status = "okay"; -}; - -&gmac { - status = "okay"; - nvmem-cell-names = "mac-address"; - nvmem-cells = <&macaddr_mac_0>; - mac-address-increment = <2>; -}; - -&switch { - status = "okay"; -}; - -&swport2 { - status = "okay"; - - label = "lan1"; -}; - -&swport3 { - status = "okay"; - - label = "lan2"; -}; - -&swport4 { - status = "okay"; - - label = "lan3"; -}; - -&swport5 { - status = "okay"; - - label = "lan4"; -}; - -&qpic_bam { - status = "okay"; -}; - &tlmm { serial_pins: serial_pinmux { mux { @@ -355,30 +216,3 @@ }; }; }; - -&usb2_hs_phy { - status = "okay"; -}; - -&usb3_ss_phy { - status = "okay"; -}; - -&usb3_hs_phy { - status = "okay"; -}; - -&wifi0 { - status = "okay"; - nvmem-cell-names = "pre-calibration", "mac-address"; - nvmem-cells = <&precal_art_1000>, <&macaddr_mac_0>; - qcom,ath10k-calibration-variant = "zte,mf287plus"; -}; - -&wifi1 { - status = "okay"; - nvmem-cell-names = "pre-calibration", "mac-address"; - nvmem-cells = <&precal_art_5000>, <&macaddr_mac_0>; - mac-address-increment = <1>; - qcom,ath10k-calibration-variant = "zte,mf287plus"; -}; diff --git a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-mf287pro.dts b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-mf287pro.dts new file mode 100644 index 0000000000..dda0f74449 --- /dev/null +++ b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-mf287pro.dts @@ -0,0 +1,265 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +// Copyright (c) 2022, Pawel Dembicki . +// Copyright (c) 2022, Giammarco Marzano . +// Copyright (c) 2023, Andreas Böhler + +#include "qcom-ipq4018-mf287.dtsi" + +/ { + model = "ZTE MF287Pro"; + compatible = "zte,mf287pro"; + + gpio_export { + compatible = "gpio-export"; + #size-cells = <0>; + + modem { + gpio-export,name = "modem-reset"; + gpio-export,output = <0>; + gpios = <&tlmm 8 GPIO_ACTIVE_HIGH>; + }; + }; + + regulator-usb-vbus { + compatible = "regulator-fixed"; + regulator-name = "USB_VBUS"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + gpio = <&tlmm 25 GPIO_ACTIVE_LOW>; + }; +}; + +&key_reset { + gpios = <&tlmm 18 GPIO_ACTIVE_LOW>; +}; + +&key_wps { + gpios = <&tlmm 68 GPIO_ACTIVE_LOW>; +}; + +&led_status { + gpios = <&tlmm 35 GPIO_ACTIVE_LOW>; +}; + +&mdio { + status = "okay"; + pinctrl-0 = <&mdio_pins>; + pinctrl-names = "default"; + reset-gpios = <&tlmm 47 GPIO_ACTIVE_LOW>; + reset-delay-us = <2000>; +}; + +&blsp1_spi1 { + pinctrl-0 = <&spi_0_pins>; + pinctrl-names = "default"; + status = "okay"; + cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>, + <&tlmm 54 GPIO_ACTIVE_HIGH>; + + flash@0 { + compatible = "jedec,spi-nor"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0>; + spi-max-frequency = <24000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "0:SBL1"; + reg = <0x0 0x40000>; + read-only; + }; + + partition@40000 { + label = "0:MIBIB"; + reg = <0x40000 0x20000>; + read-only; + }; + + partition@60000 { + label = "0:QSEE"; + reg = <0x60000 0x60000>; + read-only; + }; + + partition@c0000 { + label = "0:CDT"; + reg = <0xc0000 0x10000>; + read-only; + }; + + partition@d0000 { + label = "0:DDRPARAMS"; + reg = <0xd0000 0x10000>; + read-only; + }; + + partition@e0000 { + label = "0:APPSBLENV"; + reg = <0xe0000 0x10000>; + read-only; + }; + + partition@f0000 { + label = "0:APPSBL"; + reg = <0xf0000 0xc0000>; + read-only; + }; + + partition@1b0000 { + label = "0:reserved1"; + reg = <0x1b0000 0x50000>; + read-only; + }; + }; + }; + + spi-nand@1 { /* flash@1 ? */ + compatible = "spi-nand"; + reg = <1>; + spi-max-frequency = <24000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "fota-flag"; + reg = <0x0 0xa0000>; + read-only; + }; + + partition@a0000 { + label = "ART"; + reg = <0xa0000 0x80000>; + read-only; + compatible = "nvmem-cells"; + #address-cells = <1>; + #size-cells = <1>; + + precal_art_1000: precal@1000 { + reg = <0x1000 0x2f20>; + }; + + precal_art_5000: precal@5000 { + reg = <0x5000 0x2f20>; + }; + }; + + partition@120000 { + label = "mac"; + reg = <0x120000 0x80000>; + read-only; + compatible = "nvmem-cells"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_mac_0: macaddr@0 { + reg = <0x0 0x6>; + }; + }; + + partition@1a0000 { + label = "reserved2"; + reg = <0x1a0000 0xc0000>; + }; + + partition@260000 { + label = "cfg-param"; + reg = <0x260000 0x400000>; + read-only; + }; + + partition@660000 { + label = "log"; + reg = <0x660000 0x400000>; + }; + + partition@a60000 { + label = "oops"; + reg = <0xa60000 0xa0000>; + }; + + partition@b00000 { + label = "reserved3"; + reg = <0xb00000 0x500000>; + }; + + partition@1000000 { + label = "web"; + reg = <0x1000000 0x800000>; + }; + + partition@1800000 { + label = "rootfs"; + reg = <0x1800000 0x1d00000>; + }; + + partition@3500000 { + label = "data"; + reg = <0x3500000 0x1900000>; + }; + + partition@4e00000 { + label = "fota"; + reg = <0x4e00000 0x3200000>; + }; + }; + }; +}; + +&tlmm { + i2c_0_pins: i2c_0_pinmux { + mux { + pins = "gpio20", "gpio21"; + function = "blsp_i2c0"; + bias-disable; + }; + }; + + mdio_pins: mdio_pinmux { + mux_1 { + pins = "gpio6"; + function = "mdio"; + bias-pull-up; + }; + + mux_2 { + pins = "gpio7"; + function = "mdc"; + bias-pull-up; + }; + }; + + serial_pins: serial_pinmux { + mux { + pins = "gpio16", "gpio17"; + function = "blsp_uart0"; + bias-disable; + }; + }; + + spi_0_pins: spi_0_pinmux { + pinmux { + function = "blsp_spi0"; + pins = "gpio12", "gpio13", "gpio14", "gpio15"; + drive-strength = <12>; + bias-disable; + }; + + pinmux_cs { + function = "gpio"; + pins = "gpio12", "gpio54"; + drive-strength = <2>; + bias-disable; + output-high; + }; + }; +}; diff --git a/target/linux/ipq40xx/image/generic.mk b/target/linux/ipq40xx/image/generic.mk index 907558302c..7f4806b63d 100644 --- a/target/linux/ipq40xx/image/generic.mk +++ b/target/linux/ipq40xx/image/generic.mk @@ -1162,12 +1162,8 @@ define Device/zte_mf286d endef TARGET_DEVICES += zte_mf286d -define Device/zte_mf287plus +define Device/zte_mf287_common $(call Device/zte_mf28x_common) - DEVICE_DTS_CONFIG := config@ap.dk01.1-c2 - DEVICE_MODEL := MF287Plus - DEVICE_ALT0_VENDOR := ZTE - DEVICE_ALT0_MODEL := MF287 DEVICE_PACKAGES += ipq-wifi-zte_mf287plus SOC := qcom-ipq4018 # The recovery image is used to return back to stock (an initramfs-based image @@ -1178,8 +1174,23 @@ define Device/zte_mf287plus IMAGE/factory.bin := append-ubi IMAGE/recovery.bin := append-squashfs4-fakeroot | sysupgrade-tar kernel=$$$$(BIN_DIR)/openwrt-$$(BOARD)$$(if $$(SUBTARGET),-$$(SUBTARGET))-$$(DEVICE_NAME)-initramfs-zImage.itb rootfs=$$$$@ | append-metadata endef + +define Device/zte_mf287plus + $(call Device/zte_mf287_common) + DEVICE_DTS_CONFIG := config@ap.dk01.1-c2 + DEVICE_MODEL := MF287Plus + DEVICE_ALT0_VENDOR := ZTE + DEVICE_ALT0_MODEL := MF287 +endef TARGET_DEVICES += zte_mf287plus +define Device/zte_mf287pro + $(call Device/zte_mf287_common) + DEVICE_DTS_CONFIG := config@ap.dk04.1-c1 + DEVICE_MODEL := MF287Pro +endef +TARGET_DEVICES += zte_mf287pro + define Device/zte_mf289f $(call Device/zte_mf28x_common) DEVICE_MODEL := MF289F -- 2.30.2