From e5d4c0966736287c7ade29c5ccaf6f1ad841b7db Mon Sep 17 00:00:00 2001 From: Piotr Dymacz Date: Tue, 12 Nov 2019 22:36:28 +0100 Subject: [PATCH] ath79: add support for YunCore XD4200 and A782 YunCore XD4200 ('XD4200_W6.0' marking on PCB) is Qualcomm/Atheros based (QCA9563, QCA9886, QCA8334) dual-band, Wave-2 AC1200 ceiling AP with PoE (802.3at) support. A782 model ('T750_V5.1' marking on PCB) is a smaller version of the XD4200, with similar specification but lower TX power. Specification: - QCA9563 (775 MHz) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 2x 10/100/1000 Mbps Ethernet (QCA8334), with 802.3at PoE support (WAN) - Wi-Fi 2.4 GHz: - XD4200: 2T2R (QCA9563), with ext. PA (SKY65174-21) and LNA - A782: 2T2R (QCA9563), with ext. FEM (SKY85329-11) - Wi-Fi 5 GHz: - XD4200: 2T2R (QCA9886), with ext. FEM (SKY85728-11) - A782: 2T2R (QCA9886), with ext. FEM (SKY85735-11) - LEDs: - XD4200: 5x (2x driven by SOC, 1x driven by AC radio, 2x Ethernet) - A782: 3x (1x RGB, driven by SOC and radio, 2x Ethernet) - 1x button (reset) - 1x UART (4-pin, 2.54 mm pitch) header on PCB - 1x DC jack (12 V) Flash instructions: If your device comes with generic QSDK based firmware, you can login over telnet (login: root, empty password, default IP: 192.168.188.253), issue first (important!) 'fw_setenv' command and then perform regular upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download image to the device, SSH server is not available): fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000" sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin In case your device runs firmware with YunCore custom GUI, you can use U-Boot recovery mode: 1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with 'tftp' image renamed to 'upgrade.bin' 2. Power the device with reset button pressed and release it after 5-7 seconds, recovery mode should start downloading image from server (unfortunately, there is no visible indication that recovery got enabled - in case of problems check TFTP server logs) Signed-off-by: Piotr Dymacz --- .../linux/ath79/dts/qca9563_yuncore_a782.dts | 32 +++++ .../ath79/dts/qca9563_yuncore_xd4200.dts | 32 +++++ .../ath79/dts/qca9563_yuncore_xd4200.dtsi | 122 ++++++++++++++++++ .../generic/base-files/etc/board.d/02_network | 4 +- .../etc/hotplug.d/firmware/11-ath10k-caldata | 6 + target/linux/ath79/image/generic.mk | 22 ++++ 6 files changed, 217 insertions(+), 1 deletion(-) create mode 100644 target/linux/ath79/dts/qca9563_yuncore_a782.dts create mode 100644 target/linux/ath79/dts/qca9563_yuncore_xd4200.dts create mode 100644 target/linux/ath79/dts/qca9563_yuncore_xd4200.dtsi diff --git a/target/linux/ath79/dts/qca9563_yuncore_a782.dts b/target/linux/ath79/dts/qca9563_yuncore_a782.dts new file mode 100644 index 0000000000..27360bbe9c --- /dev/null +++ b/target/linux/ath79/dts/qca9563_yuncore_a782.dts @@ -0,0 +1,32 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include "qca9563_yuncore_xd4200.dtsi" + +/ { + compatible = "yuncore,a782", "qca,qca9563"; + model = "YunCore A782"; + + aliases { + led-boot = &led_system; + led-failsafe = &led_system; + led-running = &led_system; + led-upgrade = &led_system; + }; + + leds { + compatible = "gpio-leds"; + + led_system: system { + label = "a782:red:system"; + gpios = <&gpio 1 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + + wlan2g { + label = "a782:green:wlan2g"; + gpios = <&gpio 19 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy1tpt"; + }; + }; +}; diff --git a/target/linux/ath79/dts/qca9563_yuncore_xd4200.dts b/target/linux/ath79/dts/qca9563_yuncore_xd4200.dts new file mode 100644 index 0000000000..ab8d855884 --- /dev/null +++ b/target/linux/ath79/dts/qca9563_yuncore_xd4200.dts @@ -0,0 +1,32 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include "qca9563_yuncore_xd4200.dtsi" + +/ { + compatible = "yuncore,xd4200", "qca,qca9563"; + model = "YunCore XD4200"; + + aliases { + led-boot = &led_system; + led-failsafe = &led_system; + led-running = &led_system; + led-upgrade = &led_system; + }; + + leds { + compatible = "gpio-leds"; + + led_system: system { + label = "xd4200:blue:system"; + gpios = <&gpio 1 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + + wlan2g { + label = "xd4200:blue:wlan2g"; + gpios = <&gpio 19 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy1tpt"; + }; + }; +}; diff --git a/target/linux/ath79/dts/qca9563_yuncore_xd4200.dtsi b/target/linux/ath79/dts/qca9563_yuncore_xd4200.dtsi new file mode 100644 index 0000000000..2f7964de90 --- /dev/null +++ b/target/linux/ath79/dts/qca9563_yuncore_xd4200.dtsi @@ -0,0 +1,122 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include +#include + +#include "qca956x.dtsi" + +/ { + aliases { + label-mac-device = ð0; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + keys { + compatible = "gpio-keys"; + + reset { + linux,code = ; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + }; +}; + +ð0 { + status = "okay"; + + pll-data = <0x03000101 0x00000101 0x00001919>; + + mtd-mac-address = <&art 0x0>; + phy-mode = "sgmii"; + phy-handle = <&phy0>; +}; + +&gpio { + status = "okay"; +}; + +&mdio0 { + status = "okay"; + + phy-mask = <0>; + + phy0: ethernet-phy@0 { + reg = <0>; + phy-mode = "sgmii"; + + qca,ar8327-initvals = < + 0x04 0x00080080 /* PORT0 PAD MODE CTRL */ + 0x10 0x81000080 /* POWER_ON_STRIP */ + 0x50 0xcf37cf37 /* LED_CTRL0 */ + 0x54 0xcf37cf37 /* LED_CTRL1 */ + 0x58 0xcf37cf37 /* LED_CTRL2 */ + 0x5c 0x0000c300 /* LED_CTRL3 */ + 0x7c 0x0000007e /* PORT0_STATUS */ + >; + }; +}; + +&pcie { + status = "okay"; + + wifi@0,0 { + compatible = "pci168c,0056"; + reg = <0x0000 0 0 0 0>; + }; +}; + +&spi { + status = "okay"; + + num-cs = <1>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <25000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x000000 0x040000>; + read-only; + }; + + partition@40000 { + label = "u-boot-env"; + reg = <0x040000 0x010000>; + }; + + partition@50000 { + compatible = "denx,uimage"; + label = "firmware"; + reg = <0x050000 0xfa0000>; + }; + + art: partition@ff0000 { + label = "art"; + reg = <0xff0000 0x010000>; + read-only; + }; + }; + }; +}; + +&uart { + status = "okay"; +}; + +&wmac { + status = "okay"; + + mtd-cal-data = <&art 0x1000>; +}; diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network index c685c7e3a9..7090825c2f 100755 --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network @@ -164,7 +164,9 @@ ath79_setup_interfaces() nec,wg1200cr|\ ubnt,nanostation-ac|\ ubnt,unifiac-mesh-pro|\ - ubnt,unifiac-pro) + ubnt,unifiac-pro|\ + yuncore,a782|\ + yuncore,xd4200) ucidef_add_switch "switch0" \ "0@eth0" "2:lan" "3:wan" ;; diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index f128e8759f..0965965931 100644 --- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -154,6 +154,12 @@ case "$FIRMWARE" in ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \ /lib/firmware/ath10k/QCA9888/hw2.0/board.bin ;; + yuncore,a782|\ + yuncore,xd4200) + caldata_extract "art" 0x5000 0x2f20 + ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \ + /lib/firmware/ath10k/QCA9888/hw2.0/board.bin + ;; esac ;; *) diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk index 0c674cfe9a..865126549a 100644 --- a/target/linux/ath79/image/generic.mk +++ b/target/linux/ath79/image/generic.mk @@ -1040,6 +1040,28 @@ define Device/yuncore_a770 endef TARGET_DEVICES += yuncore_a770 +define Device/yuncore_a782 + ATH_SOC := qca9563 + DEVICE_VENDOR := YunCore + DEVICE_MODEL := A782 + DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct + IMAGE_SIZE := 16000k + IMAGES += tftp.bin + IMAGE/tftp.bin := $$(IMAGE/sysupgrade.bin) | yuncore-tftp-header-16m +endef +TARGET_DEVICES += yuncore_a782 + +define Device/yuncore_xd4200 + ATH_SOC := qca9563 + DEVICE_VENDOR := YunCore + DEVICE_MODEL := XD4200 + DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct + IMAGE_SIZE := 16000k + IMAGES += tftp.bin + IMAGE/tftp.bin := $$(IMAGE/sysupgrade.bin) | yuncore-tftp-header-16m +endef +TARGET_DEVICES += yuncore_xd4200 + define Device/zbtlink_zbt-wd323 ATH_SOC := ar9344 DEVICE_VENDOR := ZBT -- 2.30.2