From e1a55de7a7eafd40a4fab5f29153a1a3c3606818 Mon Sep 17 00:00:00 2001 From: =?utf8?q?Daniel=20Gonz=C3=A1lez=20Cabanelas?= Date: Tue, 13 Jun 2023 22:45:53 +0200 Subject: [PATCH] bmips: add support for Actiontec R1000H MIME-Version: 1.0 Content-Type: text/plain; charset=utf8 Content-Transfer-Encoding: 8bit The Actiontec R1000H is a gigabit wifi router, 2.4 GHz single band with two external antennas. It comes with a coaxial HomePNA port. Hardware: - SoC: Broadcom BCM6368 - CPU: dual core BMIPS4350 V3.1 @400Mhz - RAM: 64 MB DDR - Flash: 32 MB parallel NOR - LAN switch: Broadcom BCM53115, 5x 1Gbit - LAN coaxial : 1x HPNA 3.1, CG3211 + CG3213 - Wifi 2.4 GHz: Broadcom BCM4322 802.11bgn - USB: 1x 2.0 - Buttons: 2x, 1 reset - LEDs: 7x - UART: yes The HPNA hardware probably needs a firmware to make the coaxial port work. In the OEM firmware, it's apparently sent with an utility (inhpna) through the ethernet port. Installation via CFE web UI: 1. Connect the UART serial port. 2. Power on the router and press enter at the console prompt to stop the bootloader. 4. Browse to http://192.168.1.1 and upload the OpenWrt CFE firmware 5. Wait a few minutes for it to finish Signed-off-by: Daniel González Cabanelas --- .../bcm6368/base-files/etc/board.d/01_leds | 4 + .../bcm6368/base-files/etc/board.d/02_network | 1 + .../base-files/etc/uci-defaults/09_fix_crc | 1 + .../bmips/dts/bcm6368-actiontec-r1000h.dts | 220 ++++++++++++++++++ target/linux/bmips/image/bcm6368.mk | 15 ++ 5 files changed, 241 insertions(+) create mode 100644 target/linux/bmips/dts/bcm6368-actiontec-r1000h.dts diff --git a/target/linux/bmips/bcm6368/base-files/etc/board.d/01_leds b/target/linux/bmips/bcm6368/base-files/etc/board.d/01_leds index c7e61fe72f..9af5257c11 100644 --- a/target/linux/bmips/bcm6368/base-files/etc/board.d/01_leds +++ b/target/linux/bmips/bcm6368/base-files/etc/board.d/01_leds @@ -6,6 +6,10 @@ board_config_update case "$(board_name)" in +actiontec,r1000h) + ucidef_set_led_usbport "usb" "USB" "green:usb" "usb1-port1" "usb2-port1" + ucidef_set_led_netdev "wan" "WAN" "green:wan" "wan" + ;; comtrend,wap-5813n) ucidef_set_led_usbport "usb" "USB" "green:usb" "usb1-port1" "usb2-port1" ;; diff --git a/target/linux/bmips/bcm6368/base-files/etc/board.d/02_network b/target/linux/bmips/bcm6368/base-files/etc/board.d/02_network index 58fba05fec..fabc4216cd 100644 --- a/target/linux/bmips/bcm6368/base-files/etc/board.d/02_network +++ b/target/linux/bmips/bcm6368/base-files/etc/board.d/02_network @@ -14,6 +14,7 @@ comtrend,vr-3025un) ucidef_set_bridge_device switch ucidef_set_interface_lan "lan1 lan2 lan3 iptv" ;; +actiontec,r1000h |\ comtrend,wap-5813n |\ netgear,dgnd3700-v1 |\ netgear,dgnd3800b |\ diff --git a/target/linux/bmips/bcm6368/base-files/etc/uci-defaults/09_fix_crc b/target/linux/bmips/bcm6368/base-files/etc/uci-defaults/09_fix_crc index 63d10c9a8e..f3b1eafdfc 100644 --- a/target/linux/bmips/bcm6368/base-files/etc/uci-defaults/09_fix_crc +++ b/target/linux/bmips/bcm6368/base-files/etc/uci-defaults/09_fix_crc @@ -3,6 +3,7 @@ . /lib/functions.sh case "$(board_name)" in +actiontec,r1000h |\ comtrend,vr-3025u |\ comtrend,vr-3025un |\ comtrend,wap-5813n |\ diff --git a/target/linux/bmips/dts/bcm6368-actiontec-r1000h.dts b/target/linux/bmips/dts/bcm6368-actiontec-r1000h.dts new file mode 100644 index 0000000000..ff115afb8f --- /dev/null +++ b/target/linux/bmips/dts/bcm6368-actiontec-r1000h.dts @@ -0,0 +1,220 @@ +// SPDX-License-Identifier: GPL-2.0-or-later + +#include "bcm6368.dtsi" + +/ { + model = "Actiontec R1000H"; + compatible = "actiontec,r1000h", "brcm,bcm6368"; + + aliases { + led-boot = &led_power_green; + led-failsafe = &led_power_red; + led-running = &led_power_green; + led-upgrade = &led_power_green; + }; + + keys { + compatible = "gpio-keys-polled"; + poll-interval = <100>; + + reset { + label = "reset"; + gpios = <&gpio 34 GPIO_ACTIVE_LOW>; + linux,code = ; + debounce-interval = <60>; + }; + + wps { + label = "wps"; + gpios = <&gpio 35 GPIO_ACTIVE_LOW>; + linux,code = ; + debounce-interval = <60>; + }; + }; + + leds { + compatible = "gpio-leds"; + + led@5 { + label = "green:wan"; + gpios = <&gpio 5 GPIO_ACTIVE_HIGH>; + }; + + led@21 { + label = "green:usb"; + gpios = <&gpio 21 GPIO_ACTIVE_LOW>; + }; + + led_power_green: led@22 { + label = "green:power"; + gpios = <&gpio 22 GPIO_ACTIVE_HIGH>; + }; + + led@23 { + label = "green:wps"; + gpios = <&gpio 23 GPIO_ACTIVE_LOW>; + }; + + led_power_red: led@24 { + label = "red:power"; + gpios = <&gpio 24 GPIO_ACTIVE_HIGH>; + panic-indicator; + }; + + led@30 { + label = "red:wps"; + gpios = <&gpio 30 GPIO_ACTIVE_LOW>; + }; + + led@31 { + label = "red:wan"; + gpios = <&gpio 31 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&ehci { + status = "okay"; +}; + +ðernet { + status = "okay"; + + nvmem-cells = <&macaddr_cfe_6a0>; + nvmem-cell-names = "mac-address"; +}; + +&mdio_ext { + switch@1e { + compatible = "brcm,bcm53115"; + reg = <30>; + + dsa,member = <1 0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + + port@1 { + reg = <1>; + label = "lan2"; + }; + + port@2 { + reg = <2>; + label = "lan3"; + }; + + port@3 { + reg = <3>; + label = "lan4"; + }; + + port@4 { + reg = <4>; + label = "wan"; + }; + + port@5 { + /* HPNA coaxial port */ + reg = <5>; + label = "coax"; + + phy-mode = "mii"; + + fixed-link { + speed = <100>; + full-duplex; + }; + }; + + port@8 { + reg = <8>; + + phy-mode = "rgmii"; + ethernet = <&switch0port5>; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; +}; + +&switch0 { + dsa,member = <0 0>; + + ports { + switch0port5: port@5 { + reg = <5>; + label = "extsw"; + + phy-mode = "rgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; +}; + +&pflash { + status = "okay"; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + cfe: partition@0 { + label = "CFE"; + reg = <0x000000 0x020000>; + read-only; + }; + + partition@20000 { + label = "firmware"; + reg = <0x020000 0x1fc0000>; + compatible = "brcm,bcm963xx-imagetag"; + }; + + partition@fe0000 { + label = "nvram"; + reg = <0x1fe0000 0x020000>; + }; + }; +}; + +&ohci { + status = "okay"; +}; + +&pci { + status = "okay"; +}; + +&uart0 { + status = "okay"; +}; + +&usbh { + status = "okay"; +}; + +&cfe { + compatible = "nvmem-cells"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_cfe_6a0: macaddr@6a0 { + reg = <0x6a0 0x6>; + }; +}; diff --git a/target/linux/bmips/image/bcm6368.mk b/target/linux/bmips/image/bcm6368.mk index 83cd096959..39fcb02318 100644 --- a/target/linux/bmips/image/bcm6368.mk +++ b/target/linux/bmips/image/bcm6368.mk @@ -1,5 +1,20 @@ # SPDX-License-Identifier: GPL-2.0-or-later +define Device/actiontec_r1000h + $(Device/bcm63xx-cfe) + DEVICE_VENDOR := Actiontec + DEVICE_MODEL := R1000H + CHIP_ID := 6368 + CFE_BOARD_ID := 96368VVW + BLOCKSIZE := 0x20000 + FLASH_MB := 32 + CFE_EXTRAS += --signature "$$(DEVICE_VENDOR)" + DEVICE_PACKAGES += $(USB2_PACKAGES) \ + $(B43_PACKAGES) \ + kmod-leds-gpio +endef +TARGET_DEVICES += actiontec_r1000h + define Device/comtrend_vr-3025u $(Device/bcm63xx-cfe) DEVICE_VENDOR := Comtrend -- 2.30.2