From e1780de5ceba07c40b05834f2ca65654fc48da80 Mon Sep 17 00:00:00 2001 From: David Bauer Date: Tue, 21 Dec 2021 21:54:32 +0100 Subject: [PATCH] rockchip: remove Kernel 5.4 As v5.10 is the default kernel version now, the files for v5.4 can be dropped. Signed-off-by: David Bauer --- target/linux/rockchip/armv8/config-5.4 | 628 ------------------ ...Add-support-for-FriendlyARM-NanoPi-R.patch | 404 ----------- ...hip-Add-txpbl-node-for-RK3399-RK3328.patch | 54 -- ...add-compatible-to-NanoPi-R2S-etherne.patch | 25 - ...k3328-fix-NanoPi-R2S-GMAC-clock-name.patch | 27 - ...Add-support-for-FriendlyARM-NanoPi-R.patch | 177 ----- ...kchip-add-EEPROM-node-for-NanoPi-R4S.patch | 31 - ...-rockchip-use-system-LED-for-OpenWrt.patch | 31 - ...usb3-controller-node-for-RK3328-SoCs.patch | 62 -- ...ckchip-enable-LAN-port-on-NanoPi-R2S.patch | 60 -- ...dd-OF-node-for-USB-eth-on-NanoPi-R2S.patch | 28 - ...-host-by-default-on-rk3399-rock-pi-4.patch | 32 - 12 files changed, 1559 deletions(-) delete mode 100644 target/linux/rockchip/armv8/config-5.4 delete mode 100644 target/linux/rockchip/patches-5.4/001-rockchip-rk3328-Add-support-for-FriendlyARM-NanoPi-R.patch delete mode 100644 target/linux/rockchip/patches-5.4/004-arm64-dts-rockchip-Add-txpbl-node-for-RK3399-RK3328.patch delete mode 100644 target/linux/rockchip/patches-5.4/005-rockchip-rk3328-add-compatible-to-NanoPi-R2S-etherne.patch delete mode 100644 target/linux/rockchip/patches-5.4/006-rockchip-rk3328-fix-NanoPi-R2S-GMAC-clock-name.patch delete mode 100644 target/linux/rockchip/patches-5.4/007-v5.13-rockchip-rk3399-Add-support-for-FriendlyARM-NanoPi-R.patch delete mode 100644 target/linux/rockchip/patches-5.4/008-arm64-dts-rockchip-add-EEPROM-node-for-NanoPi-R4S.patch delete mode 100644 target/linux/rockchip/patches-5.4/100-rockchip-use-system-LED-for-OpenWrt.patch delete mode 100644 target/linux/rockchip/patches-5.4/101-dts-rockchip-add-usb3-controller-node-for-RK3328-SoCs.patch delete mode 100644 target/linux/rockchip/patches-5.4/102-rockchip-enable-LAN-port-on-NanoPi-R2S.patch delete mode 100644 target/linux/rockchip/patches-5.4/103-arm64-rockchip-add-OF-node-for-USB-eth-on-NanoPi-R2S.patch delete mode 100644 target/linux/rockchip/patches-5.4/104-rockchip-use-USB-host-by-default-on-rk3399-rock-pi-4.patch diff --git a/target/linux/rockchip/armv8/config-5.4 b/target/linux/rockchip/armv8/config-5.4 deleted file mode 100644 index d97329ccbc..0000000000 --- a/target/linux/rockchip/armv8/config-5.4 +++ /dev/null @@ -1,628 +0,0 @@ -CONFIG_64BIT=y -CONFIG_ARCH_CLOCKSOURCE_DATA=y -CONFIG_ARCH_DMA_ADDR_T_64BIT=y -CONFIG_ARCH_HIBERNATION_POSSIBLE=y -CONFIG_ARCH_KEEP_MEMBLOCK=y -CONFIG_ARCH_MMAP_RND_BITS=18 -CONFIG_ARCH_MMAP_RND_BITS_MAX=33 -CONFIG_ARCH_MMAP_RND_BITS_MIN=18 -CONFIG_ARCH_MMAP_RND_COMPAT_BITS=11 -CONFIG_ARCH_MMAP_RND_COMPAT_BITS_MIN=11 -CONFIG_ARCH_PROC_KCORE_TEXT=y -CONFIG_ARCH_ROCKCHIP=y -CONFIG_ARCH_SELECT_MEMORY_MODEL=y -CONFIG_ARCH_SPARSEMEM_DEFAULT=y -CONFIG_ARCH_SPARSEMEM_ENABLE=y -CONFIG_ARCH_SUSPEND_POSSIBLE=y -CONFIG_ARC_EMAC_CORE=y -CONFIG_ARM64=y -CONFIG_ARM64_4K_PAGES=y -CONFIG_ARM64_CNP=y -CONFIG_ARM64_CONT_SHIFT=4 -CONFIG_ARM64_ERRATUM_819472=y -CONFIG_ARM64_ERRATUM_824069=y -CONFIG_ARM64_ERRATUM_826319=y -CONFIG_ARM64_ERRATUM_827319=y -CONFIG_ARM64_ERRATUM_832075=y -CONFIG_ARM64_ERRATUM_843419=y -CONFIG_ARM64_ERRATUM_845719=y -CONFIG_ARM64_ERRATUM_858921=y -CONFIG_ARM64_HW_AFDBM=y -CONFIG_ARM64_LSE_ATOMICS=y -CONFIG_ARM64_MODULE_PLTS=y -CONFIG_ARM64_PAGE_SHIFT=12 -CONFIG_ARM64_PAN=y -CONFIG_ARM64_PA_BITS=48 -CONFIG_ARM64_PA_BITS_48=y -CONFIG_ARM64_PTR_AUTH=y -CONFIG_ARM64_RAS_EXTN=y -CONFIG_ARM64_SSBD=y -CONFIG_ARM64_SVE=y -# CONFIG_ARM64_SW_TTBR0_PAN is not set -CONFIG_ARM64_TAGGED_ADDR_ABI=y -CONFIG_ARM64_UAO=y -CONFIG_ARM64_VA_BITS=48 -# CONFIG_ARM64_VA_BITS_39 is not set -CONFIG_ARM64_VA_BITS_48=y -CONFIG_ARM64_VHE=y -CONFIG_ARM64_WORKAROUND_CLEAN_CACHE=y -# CONFIG_ARMV8_DEPRECATED is not set -CONFIG_ARM_AMBA=y -CONFIG_ARM_ARCH_TIMER=y -CONFIG_ARM_ARCH_TIMER_EVTSTREAM=y -CONFIG_ARM_ARCH_TIMER_OOL_WORKAROUND=y -CONFIG_ARM_CPUIDLE=y -CONFIG_ARM_GIC=y -CONFIG_ARM_GIC_V2M=y -CONFIG_ARM_GIC_V3=y -CONFIG_ARM_GIC_V3_ITS=y -CONFIG_ARM_GIC_V3_ITS_PCI=y -CONFIG_ARM_MHU=y -CONFIG_ARM_PSCI_CPUIDLE=y -CONFIG_ARM_PSCI_FW=y -# CONFIG_ARM_RK3399_DMC_DEVFREQ is not set -# CONFIG_ARM_SCMI_PROTOCOL is not set -CONFIG_ARM_SCPI_CPUFREQ=y -CONFIG_ARM_SCPI_POWER_DOMAIN=y -CONFIG_ARM_SCPI_PROTOCOL=y -CONFIG_ARM_SMMU=y -CONFIG_ARM_SMMU_DISABLE_BYPASS_BY_DEFAULT=y -CONFIG_ARM_SMMU_V3=y -CONFIG_AUDIT_ARCH_COMPAT_GENERIC=y -CONFIG_BACKLIGHT_CLASS_DEVICE=y -CONFIG_BACKLIGHT_GPIO=y -CONFIG_BACKLIGHT_PWM=y -CONFIG_BLK_DEV_BSG=y -CONFIG_BLK_DEV_BSGLIB=y -# CONFIG_BLK_DEV_INITRD is not set -CONFIG_BLK_DEV_INTEGRITY=y -CONFIG_BLK_DEV_LOOP=y -CONFIG_BLK_DEV_NVME=y -CONFIG_BLK_DEV_PCIESSD_MTIP32XX=y -CONFIG_BLK_DEV_SD=y -CONFIG_BLK_MQ_PCI=y -CONFIG_BLK_PM=y -CONFIG_BLK_SCSI_REQUEST=y -CONFIG_BLOCK_COMPAT=y -CONFIG_BRCMSTB_GISB_ARB=y -CONFIG_BSD_PROCESS_ACCT=y -CONFIG_BSD_PROCESS_ACCT_V3=y -CONFIG_CHARGER_GPIO=y -CONFIG_CLKDEV_LOOKUP=y -CONFIG_CLKSRC_MMIO=y -CONFIG_CLONE_BACKWARDS=y -CONFIG_CMA=y -CONFIG_CMA_ALIGNMENT=8 -CONFIG_CMA_AREAS=7 -# CONFIG_CMA_DEBUG is not set -# CONFIG_CMA_DEBUGFS is not set -CONFIG_CMA_SIZE_MBYTES=5 -# CONFIG_CMA_SIZE_SEL_MAX is not set -CONFIG_CMA_SIZE_SEL_MBYTES=y -# CONFIG_CMA_SIZE_SEL_MIN is not set -# CONFIG_CMA_SIZE_SEL_PERCENTAGE is not set -CONFIG_COMMON_CLK=y -CONFIG_COMMON_CLK_RK808=y -CONFIG_COMMON_CLK_SCPI=y -CONFIG_COMPAT=y -CONFIG_COMPAT_32BIT_TIME=y -CONFIG_COMPAT_BINFMT_ELF=y -CONFIG_COMPAT_NETLINK_MESSAGES=y -CONFIG_COMPAT_OLD_SIGACTION=y -CONFIG_CONFIGFS_FS=y -CONFIG_CONSOLE_TRANSLATIONS=y -CONFIG_CONTIG_ALLOC=y -CONFIG_CPUFREQ_DT=y -CONFIG_CPUFREQ_DT_PLATDEV=y -CONFIG_CPU_FREQ=y -# CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE is not set -CONFIG_CPU_FREQ_DEFAULT_GOV_SCHEDUTIL=y -CONFIG_CPU_FREQ_GOV_ATTR_SET=y -# CONFIG_CPU_FREQ_GOV_CONSERVATIVE is not set -# CONFIG_CPU_FREQ_GOV_ONDEMAND is not set -CONFIG_CPU_FREQ_GOV_PERFORMANCE=y -CONFIG_CPU_FREQ_GOV_POWERSAVE=y -CONFIG_CPU_FREQ_GOV_SCHEDUTIL=y -# CONFIG_CPU_FREQ_GOV_USERSPACE is not set -CONFIG_CPU_FREQ_STAT=y -CONFIG_CPU_IDLE=y -CONFIG_CPU_IDLE_GOV_MENU=y -CONFIG_CPU_IDLE_MULTIPLE_DRIVERS=y -CONFIG_CPU_ISOLATION=y -CONFIG_CPU_PM=y -CONFIG_CPU_RMAP=y -CONFIG_CPU_THERMAL=y -CONFIG_CRASH_CORE=y -CONFIG_CRASH_DUMP=y -CONFIG_CRC16=y -# CONFIG_CRC32_SARWATE is not set -CONFIG_CRC32_SLICEBY8=y -CONFIG_CRC_T10DIF=y -CONFIG_CROSS_MEMORY_ATTACH=y -CONFIG_CRYPTO_AEAD=y -CONFIG_CRYPTO_AEAD2=y -CONFIG_CRYPTO_CRC32=y -CONFIG_CRYPTO_CRC32C=y -CONFIG_CRYPTO_CRCT10DIF=y -# CONFIG_CRYPTO_DEV_ROCKCHIP is not set -CONFIG_CRYPTO_HASH=y -CONFIG_CRYPTO_HASH2=y -CONFIG_CRYPTO_MANAGER=y -CONFIG_CRYPTO_MANAGER2=y -CONFIG_CRYPTO_NULL2=y -CONFIG_CRYPTO_RNG2=y -CONFIG_DCACHE_WORD_ACCESS=y -CONFIG_DEBUG_BUGVERBOSE=y -# CONFIG_DEVFREQ_GOV_PASSIVE is not set -CONFIG_DEVFREQ_GOV_PERFORMANCE=y -CONFIG_DEVFREQ_GOV_POWERSAVE=y -CONFIG_DEVFREQ_GOV_SIMPLE_ONDEMAND=y -CONFIG_DEVFREQ_GOV_USERSPACE=y -# CONFIG_DEVFREQ_THERMAL is not set -CONFIG_DEVMEM=y -# CONFIG_DEVPORT is not set -CONFIG_DEVTMPFS=y -CONFIG_DEVTMPFS_MOUNT=y -CONFIG_DMADEVICES=y -CONFIG_DMA_CMA=y -CONFIG_DMA_DIRECT_REMAP=y -CONFIG_DMA_ENGINE=y -CONFIG_DMA_OF=y -CONFIG_DMA_REMAP=y -CONFIG_DMA_SHARED_BUFFER=y -CONFIG_DNOTIFY=y -CONFIG_DRM_RCAR_WRITEBACK=y -# CONFIG_DRM_ROCKCHIP is not set -CONFIG_DTC=y -CONFIG_DT_IDLE_STATES=y -CONFIG_DUMMY_CONSOLE=y -CONFIG_DWMAC_DWC_QOS_ETH=y -CONFIG_DWMAC_GENERIC=y -CONFIG_DWMAC_ROCKCHIP=y -CONFIG_EDAC_SUPPORT=y -CONFIG_EEPROM_AT24=y -CONFIG_EMAC_ROCKCHIP=y -CONFIG_ENABLE_MUST_CHECK=y -CONFIG_ENERGY_MODEL=y -CONFIG_EXT4_FS=y -CONFIG_EXT4_FS_POSIX_ACL=y -CONFIG_EXTCON=y -CONFIG_F2FS_FS=y -CONFIG_FANOTIFY=y -CONFIG_FHANDLE=y -CONFIG_FIXED_PHY=y -CONFIG_FIX_EARLYCON_MEM=y -# CONFIG_FLATMEM_MANUAL is not set -# CONFIG_FORTIFY_SOURCE is not set -CONFIG_FRAME_POINTER=y -CONFIG_FRAME_WARN=2048 -CONFIG_FS_IOMAP=y -CONFIG_FS_MBCACHE=y -CONFIG_FS_POSIX_ACL=y -CONFIG_FW_LOADER_PAGED_BUF=y -CONFIG_GENERIC_ALLOCATOR=y -CONFIG_GENERIC_ARCH_TOPOLOGY=y -CONFIG_GENERIC_BUG=y -CONFIG_GENERIC_BUG_RELATIVE_POINTERS=y -CONFIG_GENERIC_CLOCKEVENTS=y -CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y -CONFIG_GENERIC_CPU_AUTOPROBE=y -CONFIG_GENERIC_CPU_VULNERABILITIES=y -CONFIG_GENERIC_CSUM=y -CONFIG_GENERIC_EARLY_IOREMAP=y -CONFIG_GENERIC_GETTIMEOFDAY=y -CONFIG_GENERIC_IDLE_POLL_SETUP=y -CONFIG_GENERIC_IRQ_CHIP=y -CONFIG_GENERIC_IRQ_EFFECTIVE_AFF_MASK=y -CONFIG_GENERIC_IRQ_MIGRATION=y -CONFIG_GENERIC_IRQ_MULTI_HANDLER=y -CONFIG_GENERIC_IRQ_SHOW=y -CONFIG_GENERIC_IRQ_SHOW_LEVEL=y -CONFIG_GENERIC_MSI_IRQ=y -CONFIG_GENERIC_MSI_IRQ_DOMAIN=y -CONFIG_GENERIC_PCI_IOMAP=y -CONFIG_GENERIC_PHY=y -CONFIG_GENERIC_PINCONF=y -CONFIG_GENERIC_SCHED_CLOCK=y -CONFIG_GENERIC_SMP_IDLE_THREAD=y -CONFIG_GENERIC_STRNCPY_FROM_USER=y -CONFIG_GENERIC_STRNLEN_USER=y -CONFIG_GENERIC_TIME_VSYSCALL=y -CONFIG_GPIOLIB=y -CONFIG_GPIO_DWAPB=y -CONFIG_GPIO_GENERIC=y -CONFIG_GPIO_GENERIC_PLATFORM=y -CONFIG_HANDLE_DOMAIN_IRQ=y -# CONFIG_HARDENED_USERCOPY is not set -CONFIG_HARDEN_BRANCH_PREDICTOR=y -CONFIG_HARDIRQS_SW_RESEND=y -CONFIG_HAS_DMA=y -CONFIG_HAS_IOMEM=y -CONFIG_HAS_IOPORT_MAP=y -CONFIG_HID=y -CONFIG_HID_GENERIC=y -CONFIG_HOLES_IN_ZONE=y -CONFIG_HOTPLUG_CPU=y -CONFIG_HOTPLUG_PCI=y -# CONFIG_HOTPLUG_PCI_CPCI is not set -# CONFIG_HOTPLUG_PCI_PCIE is not set -# CONFIG_HOTPLUG_PCI_SHPC is not set -CONFIG_HUGETLBFS=y -CONFIG_HUGETLB_PAGE=y -CONFIG_HWMON=y -CONFIG_HWSPINLOCK=y -CONFIG_HW_CONSOLE=y -CONFIG_I2C=y -CONFIG_I2C_BOARDINFO=y -CONFIG_I2C_CHARDEV=y -CONFIG_I2C_COMPAT=y -CONFIG_I2C_HELPER_AUTO=y -CONFIG_I2C_RK3X=y -CONFIG_ILLEGAL_POINTER_VALUE=0xdead000000000000 -CONFIG_INDIRECT_PIO=y -CONFIG_INPUT=y -CONFIG_INPUT_EVDEV=y -CONFIG_INPUT_FF_MEMLESS=y -CONFIG_INPUT_KEYBOARD=y -CONFIG_INPUT_LEDS=y -CONFIG_INPUT_MATRIXKMAP=y -# CONFIG_INPUT_MISC is not set -# CONFIG_INPUT_RK805_PWRKEY is not set -CONFIG_IOMMU_API=y -# CONFIG_IOMMU_DEBUGFS is not set -# CONFIG_IOMMU_DEFAULT_PASSTHROUGH is not set -CONFIG_IOMMU_DMA=y -CONFIG_IOMMU_IOVA=y -CONFIG_IOMMU_IO_PGTABLE=y -# CONFIG_IOMMU_IO_PGTABLE_ARMV7S is not set -CONFIG_IOMMU_IO_PGTABLE_LPAE=y -# CONFIG_IOMMU_IO_PGTABLE_LPAE_SELFTEST is not set -CONFIG_IOMMU_SUPPORT=y -# CONFIG_IO_STRICT_DEVMEM is not set -CONFIG_IO_URING=y -CONFIG_IRQCHIP=y -CONFIG_IRQ_DOMAIN=y -CONFIG_IRQ_DOMAIN_HIERARCHY=y -CONFIG_IRQ_FORCED_THREADING=y -CONFIG_IRQ_MSI_IOMMU=y -CONFIG_IRQ_TIME_ACCOUNTING=y -CONFIG_IRQ_WORK=y -CONFIG_JBD2=y -CONFIG_JFFS2_ZLIB=y -CONFIG_JUMP_LABEL=y -CONFIG_KALLSYMS=y -CONFIG_KEXEC_CORE=y -CONFIG_KEXEC_FILE=y -# CONFIG_KEXEC_SIG is not set -CONFIG_KSM=y -# CONFIG_LEDS_BRIGHTNESS_HW_CHANGED is not set -CONFIG_LEDS_GPIO=y -CONFIG_LEDS_PWM=y -CONFIG_LEDS_SYSCON=y -CONFIG_LEDS_TRIGGER_CPU=y -CONFIG_LEDS_TRIGGER_PANIC=y -CONFIG_LEGACY_PTYS=y -CONFIG_LEGACY_PTY_COUNT=16 -CONFIG_LIBCRC32C=y -CONFIG_LIBFDT=y -CONFIG_LOCALVERSION_AUTO=y -CONFIG_LOCK_DEBUGGING_SUPPORT=y -CONFIG_LOCK_SPIN_ON_OWNER=y -CONFIG_LOG_BUF_SHIFT=19 -CONFIG_MAGIC_SYSRQ=y -CONFIG_MAGIC_SYSRQ_SERIAL=y -CONFIG_MAILBOX=y -# CONFIG_MAILBOX_TEST is not set -CONFIG_MANDATORY_FILE_LOCKING=y -CONFIG_MDIO_BUS=y -CONFIG_MDIO_BUS_MUX=y -CONFIG_MDIO_BUS_MUX_GPIO=y -CONFIG_MDIO_BUS_MUX_MMIOREG=y -CONFIG_MDIO_DEVICE=y -CONFIG_MEMFD_CREATE=y -CONFIG_MEMORY_ISOLATION=y -CONFIG_MFD_CORE=y -CONFIG_MFD_RK808=y -CONFIG_MFD_SYSCON=y -CONFIG_MIGRATION=y -CONFIG_MMC=y -CONFIG_MMC_BLOCK=y -CONFIG_MMC_BLOCK_MINORS=32 -CONFIG_MMC_CQHCI=y -CONFIG_MMC_DW=y -# CONFIG_MMC_DW_BLUEFIELD is not set -# CONFIG_MMC_DW_EXYNOS is not set -# CONFIG_MMC_DW_HI3798CV200 is not set -# CONFIG_MMC_DW_K3 is not set -# CONFIG_MMC_DW_PCI is not set -CONFIG_MMC_DW_PLTFM=y -CONFIG_MMC_DW_ROCKCHIP=y -CONFIG_MMC_SDHCI=y -CONFIG_MMC_SDHCI_OF_ARASAN=y -CONFIG_MMC_SDHCI_OF_DWCMSHC=y -# CONFIG_MMC_SDHCI_PCI is not set -CONFIG_MMC_SDHCI_PLTFM=y -CONFIG_MODULES_USE_ELF_RELA=y -CONFIG_MQ_IOSCHED_DEADLINE=y -# CONFIG_MTD_CFI is not set -CONFIG_MTD_CMDLINE_PARTS=y -# CONFIG_MTD_COMPLEX_MAPPINGS is not set -CONFIG_MTD_SPI_NOR=y -CONFIG_MTD_SPI_NOR_USE_4K_SECTORS=y -CONFIG_MTD_SPLIT_FIRMWARE=y -CONFIG_MUTEX_SPIN_ON_OWNER=y -CONFIG_NEED_DMA_MAP_STATE=y -CONFIG_NEED_SG_DMA_LENGTH=y -CONFIG_NET_FLOW_LIMIT=y -CONFIG_NLS=y -CONFIG_NLS_ISO8859_1=y -CONFIG_NOP_USB_XCEIV=y -CONFIG_NO_HZ_COMMON=y -CONFIG_NO_HZ_IDLE=y -CONFIG_NR_CPUS=256 -CONFIG_NVMEM=y -CONFIG_NVMEM_SYSFS=y -CONFIG_NVME_CORE=y -# CONFIG_NVME_MULTIPATH is not set -# CONFIG_NVME_TCP is not set -CONFIG_OF=y -CONFIG_OF_ADDRESS=y -CONFIG_OF_DYNAMIC=y -CONFIG_OF_EARLY_FLATTREE=y -CONFIG_OF_FLATTREE=y -CONFIG_OF_GPIO=y -CONFIG_OF_IOMMU=y -CONFIG_OF_IRQ=y -CONFIG_OF_KOBJ=y -CONFIG_OF_MDIO=y -CONFIG_OF_NET=y -CONFIG_OF_OVERLAY=y -CONFIG_OF_RESOLVE=y -CONFIG_OLD_SIGSUSPEND3=y -# CONFIG_OVERLAY_FS_XINO_AUTO is not set -CONFIG_PADATA=y -CONFIG_PAGE_POOL=y -# CONFIG_PANIC_ON_OOPS is not set -CONFIG_PANIC_ON_OOPS_VALUE=0 -CONFIG_PANIC_TIMEOUT=0 -# CONFIG_PARTITION_ADVANCED is not set -CONFIG_PARTITION_PERCPU=y -CONFIG_PCI=y -CONFIG_PCIEAER=y -CONFIG_PCIEASPM=y -# CONFIG_PCIEASPM_DEBUG is not set -CONFIG_PCIEASPM_DEFAULT=y -# CONFIG_PCIEASPM_PERFORMANCE is not set -# CONFIG_PCIEASPM_POWERSAVE is not set -# CONFIG_PCIEASPM_POWER_SUPERSAVE is not set -CONFIG_PCIEPORTBUS=y -CONFIG_PCIE_PME=y -CONFIG_PCIE_ROCKCHIP=y -CONFIG_PCIE_ROCKCHIP_HOST=y -CONFIG_PCI_DOMAINS=y -CONFIG_PCI_DOMAINS_GENERIC=y -CONFIG_PCI_MSI=y -CONFIG_PCI_MSI_IRQ_DOMAIN=y -CONFIG_PCI_STUB=y -CONFIG_PGTABLE_LEVELS=4 -CONFIG_PHYLIB=y -CONFIG_PHYLINK=y -CONFIG_PHYS_ADDR_T_64BIT=y -CONFIG_PHY_ROCKCHIP_DP=y -CONFIG_PHY_ROCKCHIP_EMMC=y -# CONFIG_PHY_ROCKCHIP_INNO_HDMI is not set -CONFIG_PHY_ROCKCHIP_INNO_USB2=y -CONFIG_PHY_ROCKCHIP_PCIE=y -CONFIG_PHY_ROCKCHIP_TYPEC=y -CONFIG_PHY_ROCKCHIP_USB=y -CONFIG_PINCTRL=y -# CONFIG_PINCTRL_RK805 is not set -CONFIG_PINCTRL_ROCKCHIP=y -# CONFIG_PINCTRL_SINGLE is not set -CONFIG_PL330_DMA=y -CONFIG_PLATFORM_MHU=y -CONFIG_PM=y -CONFIG_PM_CLK=y -CONFIG_PM_DEVFREQ=y -# CONFIG_PM_DEVFREQ_EVENT is not set -CONFIG_PM_GENERIC_DOMAINS=y -CONFIG_PM_GENERIC_DOMAINS_OF=y -CONFIG_PM_OPP=y -CONFIG_POWER_AVS=y -CONFIG_POWER_RESET=y -CONFIG_POWER_SUPPLY=y -CONFIG_POWER_SUPPLY_HWMON=y -CONFIG_PREEMPT=y -CONFIG_PREEMPTION=y -CONFIG_PREEMPT_COUNT=y -# CONFIG_PREEMPT_NONE is not set -CONFIG_PREEMPT_RCU=y -CONFIG_PRINTK_TIME=y -# CONFIG_PRINT_QUOTA_WARNING is not set -CONFIG_PROC_PAGE_MONITOR=y -CONFIG_PROC_VMCORE=y -CONFIG_PWM=y -CONFIG_PWM_ROCKCHIP=y -CONFIG_PWM_SYSFS=y -# CONFIG_QFMT_V1 is not set -# CONFIG_QFMT_V2 is not set -CONFIG_QUEUED_RWLOCKS=y -CONFIG_QUEUED_SPINLOCKS=y -CONFIG_QUOTA=y -CONFIG_QUOTACTL=y -# CONFIG_QUOTA_NETLINK_INTERFACE is not set -CONFIG_RAID_ATTRS=y -CONFIG_RANDOMIZE_BASE=y -CONFIG_RANDOMIZE_MODULE_REGION_FULL=y -CONFIG_RAS=y -CONFIG_RATIONAL=y -# CONFIG_RAVE_SP_CORE is not set -CONFIG_RCU_TRACE=y -CONFIG_REALTEK_PHY=y -CONFIG_REFCOUNT_FULL=y -CONFIG_REGMAP=y -CONFIG_REGMAP_I2C=y -CONFIG_REGMAP_IRQ=y -CONFIG_REGMAP_MMIO=y -CONFIG_REGULATOR=y -CONFIG_REGULATOR_FAN53555=y -CONFIG_REGULATOR_FIXED_VOLTAGE=y -CONFIG_REGULATOR_GPIO=y -CONFIG_REGULATOR_PWM=y -CONFIG_REGULATOR_RK808=y -CONFIG_RELOCATABLE=y -CONFIG_RESET_CONTROLLER=y -CONFIG_RFS_ACCEL=y -CONFIG_ROCKCHIP_EFUSE=y -CONFIG_ROCKCHIP_GRF=y -CONFIG_ROCKCHIP_IODOMAIN=y -CONFIG_ROCKCHIP_IOMMU=y -CONFIG_ROCKCHIP_MBOX=y -CONFIG_ROCKCHIP_PHY=y -CONFIG_ROCKCHIP_PM_DOMAINS=y -# CONFIG_ROCKCHIP_SARADC is not set -CONFIG_ROCKCHIP_THERMAL=y -CONFIG_ROCKCHIP_TIMER=y -CONFIG_RODATA_FULL_DEFAULT_ENABLED=y -CONFIG_RPS=y -CONFIG_RSEQ=y -CONFIG_RTC_CLASS=y -CONFIG_RTC_DRV_RK808=y -CONFIG_RTC_I2C_AND_SPI=y -CONFIG_RTC_NVMEM=y -# CONFIG_RUNTIME_TESTING_MENU is not set -CONFIG_RWSEM_SPIN_ON_OWNER=y -CONFIG_SCHED_MC=y -CONFIG_SCSI=y -# CONFIG_SCSI_LOWLEVEL is not set -# CONFIG_SCSI_PROC_FS is not set -CONFIG_SCSI_SAS_ATTRS=y -CONFIG_SCSI_SAS_HOST_SMP=y -CONFIG_SCSI_SAS_LIBSAS=y -# CONFIG_SECURITY_DMESG_RESTRICT is not set -CONFIG_SENSORS_ARM_SCPI=y -CONFIG_SERIAL_8250_DEPRECATED_OPTIONS=y -CONFIG_SERIAL_8250_DW=y -CONFIG_SERIAL_8250_DWLIB=y -CONFIG_SERIAL_8250_EXAR=y -CONFIG_SERIAL_8250_EXTENDED=y -CONFIG_SERIAL_8250_FSL=y -CONFIG_SERIAL_8250_NR_UARTS=4 -CONFIG_SERIAL_8250_PCI=y -CONFIG_SERIAL_8250_RUNTIME_UARTS=4 -CONFIG_SERIAL_8250_SHARE_IRQ=y -CONFIG_SERIAL_AMBA_PL011=y -CONFIG_SERIAL_AMBA_PL011_CONSOLE=y -CONFIG_SERIAL_DEV_BUS=y -CONFIG_SERIAL_DEV_CTRL_TTYPORT=y -CONFIG_SERIAL_MCTRL_GPIO=y -CONFIG_SERIAL_OF_PLATFORM=y -CONFIG_SERIO=y -CONFIG_SERIO_AMBAKMI=y -CONFIG_SERIO_LIBPS2=y -CONFIG_SG_POOL=y -CONFIG_SIMPLE_PM_BUS=y -CONFIG_SLUB_DEBUG=y -CONFIG_SMP=y -# CONFIG_SND_SOC_ROCKCHIP is not set -CONFIG_SPARSEMEM=y -CONFIG_SPARSEMEM_EXTREME=y -CONFIG_SPARSEMEM_MANUAL=y -CONFIG_SPARSEMEM_VMEMMAP=y -CONFIG_SPARSEMEM_VMEMMAP_ENABLE=y -CONFIG_SPARSE_IRQ=y -CONFIG_SPI=y -CONFIG_SPI_BITBANG=y -CONFIG_SPI_DYNAMIC=y -CONFIG_SPI_MASTER=y -CONFIG_SPI_MEM=y -CONFIG_SPI_ROCKCHIP=y -CONFIG_SPI_SPIDEV=y -# CONFIG_SQUASHFS_DECOMP_MULTI_PERCPU is not set -CONFIG_SQUASHFS_DECOMP_SINGLE=y -# CONFIG_SQUASHFS_EMBEDDED is not set -CONFIG_SQUASHFS_FILE_CACHE=y -# CONFIG_SQUASHFS_FILE_DIRECT is not set -CONFIG_SRAM=y -CONFIG_SRCU=y -CONFIG_STACKPROTECTOR=y -CONFIG_STACKPROTECTOR_STRONG=y -CONFIG_STMMAC_ETH=y -CONFIG_STMMAC_PLATFORM=y -# CONFIG_STMMAC_SELFTESTS is not set -CONFIG_STRICT_DEVMEM=y -# CONFIG_STRIP_ASM_SYMS is not set -# CONFIG_SWAP is not set -CONFIG_SWIOTLB=y -CONFIG_SWPHY=y -CONFIG_SYNC_FILE=y -CONFIG_SYSCTL_EXCEPTION_TRACE=y -CONFIG_SYSFS_SYSCALL=y -CONFIG_SYSVIPC_COMPAT=y -CONFIG_SYS_SUPPORTS_HUGETLBFS=y -# CONFIG_TEXTSEARCH is not set -CONFIG_THERMAL=y -CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y -CONFIG_THERMAL_EMERGENCY_POWEROFF_DELAY_MS=0 -CONFIG_THERMAL_EMULATION=y -CONFIG_THERMAL_GOV_POWER_ALLOCATOR=y -CONFIG_THERMAL_GOV_STEP_WISE=y -CONFIG_THERMAL_HWMON=y -CONFIG_THERMAL_OF=y -CONFIG_THREAD_INFO_IN_TASK=y -CONFIG_TICK_CPU_ACCOUNTING=y -CONFIG_TIMER_OF=y -CONFIG_TIMER_PROBE=y -CONFIG_TRACE_CLOCK=y -CONFIG_TRANSPARENT_HUGEPAGE=y -CONFIG_TRANSPARENT_HUGEPAGE_ALWAYS=y -# CONFIG_TRANSPARENT_HUGEPAGE_MADVISE is not set -CONFIG_TRANSPARENT_HUGE_PAGECACHE=y -CONFIG_TREE_SRCU=y -CONFIG_TYPEC=y -# CONFIG_TYPEC_DP_ALTMODE is not set -CONFIG_TYPEC_FUSB302=y -# CONFIG_TYPEC_MUX_PI3USB30532 is not set -# CONFIG_TYPEC_TCPCI is not set -CONFIG_TYPEC_TCPM=y -# CONFIG_TYPEC_TPS6598X is not set -# CONFIG_UCLAMP_TASK is not set -# CONFIG_UEVENT_HELPER is not set -CONFIG_UNINLINE_SPIN_UNLOCK=y -CONFIG_UNMAP_KERNEL_AT_EL0=y -CONFIG_USB=y -CONFIG_USB_COMMON=y -CONFIG_USB_DWC3=y -CONFIG_USB_DWC3_HOST=y -CONFIG_USB_DWC3_OF_SIMPLE=y -CONFIG_USB_EHCI_HCD=y -CONFIG_USB_EHCI_HCD_PLATFORM=y -# CONFIG_USB_EHCI_ROOT_HUB_TT is not set -CONFIG_USB_HID=y -CONFIG_USB_OHCI_HCD=y -CONFIG_USB_OHCI_HCD_PLATFORM=y -CONFIG_USB_PHY=y -CONFIG_USB_ROLE_SWITCH=y -CONFIG_USB_STORAGE=y -CONFIG_USB_SUPPORT=y -CONFIG_USB_ULPI=y -CONFIG_USB_ULPI_BUS=y -CONFIG_USB_ULPI_VIEWPORT=y -CONFIG_USB_XHCI_HCD=y -CONFIG_USB_XHCI_PLATFORM=y -# CONFIG_VIRTIO_MENU is not set -CONFIG_VMAP_STACK=y -CONFIG_VM_EVENT_COUNTERS=y -CONFIG_VT=y -CONFIG_VT_CONSOLE=y -CONFIG_VT_HW_CONSOLE_BINDING=y -# CONFIG_WATCHDOG is not set -CONFIG_XARRAY_MULTI=y -CONFIG_XPS=y -CONFIG_XXHASH=y -CONFIG_XZ_DEC_ARM=y -CONFIG_XZ_DEC_ARMTHUMB=y -CONFIG_XZ_DEC_BCJ=y -CONFIG_ZLIB_DEFLATE=y -CONFIG_ZLIB_INFLATE=y -CONFIG_ZONE_DMA32=y diff --git a/target/linux/rockchip/patches-5.4/001-rockchip-rk3328-Add-support-for-FriendlyARM-NanoPi-R.patch b/target/linux/rockchip/patches-5.4/001-rockchip-rk3328-Add-support-for-FriendlyARM-NanoPi-R.patch deleted file mode 100644 index 69ee8a7c3a..0000000000 --- a/target/linux/rockchip/patches-5.4/001-rockchip-rk3328-Add-support-for-FriendlyARM-NanoPi-R.patch +++ /dev/null @@ -1,404 +0,0 @@ -From 0720be5371c806c1b89936984a321248fa739bea Mon Sep 17 00:00:00 2001 -From: David Bauer -Date: Fri, 10 Jul 2020 15:57:46 +0200 -Subject: [PATCH] rockchip: rk3328: Add support for FriendlyARM NanoPi R2S - -This adds support for the NanoPi R2S from FriendlyARM. - -Rockchip RK3328 SoC -1GB DDR4 RAM -Gigabit Ethernet (WAN) -Gigabit Ethernet (USB3) (LAN) -USB 2.0 Host Port -MicroSD slot -Reset button -WAN - LAN - SYS LED - -Signed-off-by: David Bauer ---- - arch/arm64/boot/dts/rockchip/Makefile | 1 + - .../boot/dts/rockchip/rk3328-nanopi-r2s.dts | 368 ++++++++++++++++++ - 2 files changed, 369 insertions(+) - create mode 100644 arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts - ---- a/arch/arm64/boot/dts/rockchip/Makefile -+++ b/arch/arm64/boot/dts/rockchip/Makefile -@@ -1,6 +1,7 @@ - # SPDX-License-Identifier: GPL-2.0 - dtb-$(CONFIG_ARCH_ROCKCHIP) += px30-evb.dtb - dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-evb.dtb -+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-nanopi-r2s.dtb - dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-rock64.dtb - dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-roc-cc.dtb - dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-evb-act8846.dtb ---- /dev/null -+++ b/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts -@@ -0,0 +1,368 @@ -+// SPDX-License-Identifier: (GPL-2.0+ OR MIT) -+/* -+ * Copyright (c) 2020 David Bauer -+ */ -+ -+/dts-v1/; -+ -+#include -+#include -+#include "rk3328.dtsi" -+ -+/ { -+ model = "FriendlyElec NanoPi R2S"; -+ compatible = "friendlyarm,nanopi-r2s", "rockchip,rk3328"; -+ -+ chosen { -+ stdout-path = "serial2:1500000n8"; -+ }; -+ -+ gmac_clk: gmac-clock { -+ compatible = "fixed-clock"; -+ clock-frequency = <125000000>; -+ clock-output-names = "gmac_clk"; -+ #clock-cells = <0>; -+ }; -+ -+ keys { -+ compatible = "gpio-keys"; -+ pinctrl-0 = <&reset_button_pin>; -+ pinctrl-names = "default"; -+ -+ reset { -+ label = "reset"; -+ gpios = <&gpio0 RK_PA0 GPIO_ACTIVE_LOW>; -+ linux,code = ; -+ debounce-interval = <50>; -+ }; -+ }; -+ -+ leds { -+ compatible = "gpio-leds"; -+ pinctrl-0 = <&lan_led_pin>, <&sys_led_pin>, <&wan_led_pin>; -+ pinctrl-names = "default"; -+ -+ lan_led: led-0 { -+ gpios = <&gpio2 RK_PB7 GPIO_ACTIVE_HIGH>; -+ label = "nanopi-r2s:green:lan"; -+ }; -+ -+ sys_led: led-1 { -+ gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_HIGH>; -+ label = "nanopi-r2s:red:sys"; -+ }; -+ -+ wan_led: led-2 { -+ gpios = <&gpio2 RK_PC2 GPIO_ACTIVE_HIGH>; -+ label = "nanopi-r2s:green:wan"; -+ }; -+ }; -+ -+ vcc_io_sdio: sdmmcio-regulator { -+ compatible = "regulator-gpio"; -+ enable-active-high; -+ gpios = <&gpio1 RK_PD4 GPIO_ACTIVE_HIGH>; -+ pinctrl-0 = <&sdio_vcc_pin>; -+ pinctrl-names = "default"; -+ regulator-name = "vcc_io_sdio"; -+ regulator-always-on; -+ regulator-min-microvolt = <1800000>; -+ regulator-max-microvolt = <3300000>; -+ regulator-settling-time-us = <5000>; -+ regulator-type = "voltage"; -+ startup-delay-us = <2000>; -+ states = <1800000 0x1 -+ 3300000 0x0>; -+ vin-supply = <&vcc_io_33>; -+ }; -+ -+ vcc_sd: sdmmc-regulator { -+ compatible = "regulator-fixed"; -+ gpio = <&gpio0 RK_PD6 GPIO_ACTIVE_LOW>; -+ pinctrl-0 = <&sdmmc0m1_gpio>; -+ pinctrl-names = "default"; -+ regulator-name = "vcc_sd"; -+ regulator-boot-on; -+ regulator-min-microvolt = <3300000>; -+ regulator-max-microvolt = <3300000>; -+ vin-supply = <&vcc_io_33>; -+ }; -+ -+ vdd_5v: vdd-5v { -+ compatible = "regulator-fixed"; -+ regulator-name = "vdd_5v"; -+ regulator-always-on; -+ regulator-boot-on; -+ regulator-min-microvolt = <5000000>; -+ regulator-max-microvolt = <5000000>; -+ }; -+}; -+ -+&cpu0 { -+ cpu-supply = <&vdd_arm>; -+}; -+ -+&cpu1 { -+ cpu-supply = <&vdd_arm>; -+}; -+ -+&cpu2 { -+ cpu-supply = <&vdd_arm>; -+}; -+ -+&cpu3 { -+ cpu-supply = <&vdd_arm>; -+}; -+ -+&gmac2io { -+ assigned-clocks = <&cru SCLK_MAC2IO>, <&cru SCLK_MAC2IO_EXT>; -+ assigned-clock-parents = <&gmac_clk>, <&gmac_clk>; -+ clock_in_out = "input"; -+ phy-handle = <&rtl8211e>; -+ phy-mode = "rgmii"; -+ phy-supply = <&vcc_io_33>; -+ pinctrl-0 = <&rgmiim1_pins>; -+ pinctrl-names = "default"; -+ rx_delay = <0x18>; -+ snps,aal; -+ tx_delay = <0x24>; -+ status = "okay"; -+ -+ mdio { -+ compatible = "snps,dwmac-mdio"; -+ #address-cells = <1>; -+ #size-cells = <0>; -+ -+ rtl8211e: ethernet-phy@1 { -+ reg = <1>; -+ pinctrl-0 = <ð_phy_reset_pin>; -+ pinctrl-names = "default"; -+ reset-assert-us = <10000>; -+ reset-deassert-us = <50000>; -+ reset-gpios = <&gpio1 RK_PC2 GPIO_ACTIVE_LOW>; -+ }; -+ }; -+}; -+ -+&i2c1 { -+ status = "okay"; -+ -+ rk805: pmic@18 { -+ compatible = "rockchip,rk805"; -+ reg = <0x18>; -+ interrupt-parent = <&gpio1>; -+ interrupts = <24 IRQ_TYPE_LEVEL_LOW>; -+ #clock-cells = <1>; -+ clock-output-names = "xin32k", "rk805-clkout2"; -+ gpio-controller; -+ #gpio-cells = <2>; -+ pinctrl-0 = <&pmic_int_l>; -+ pinctrl-names = "default"; -+ rockchip,system-power-controller; -+ wakeup-source; -+ -+ vcc1-supply = <&vdd_5v>; -+ vcc2-supply = <&vdd_5v>; -+ vcc3-supply = <&vdd_5v>; -+ vcc4-supply = <&vdd_5v>; -+ vcc5-supply = <&vcc_io_33>; -+ vcc6-supply = <&vdd_5v>; -+ -+ regulators { -+ vdd_log: DCDC_REG1 { -+ regulator-name = "vdd_log"; -+ regulator-always-on; -+ regulator-boot-on; -+ regulator-min-microvolt = <712500>; -+ regulator-max-microvolt = <1450000>; -+ regulator-ramp-delay = <12500>; -+ -+ regulator-state-mem { -+ regulator-on-in-suspend; -+ regulator-suspend-microvolt = <1000000>; -+ }; -+ }; -+ -+ vdd_arm: DCDC_REG2 { -+ regulator-name = "vdd_arm"; -+ regulator-always-on; -+ regulator-boot-on; -+ regulator-min-microvolt = <712500>; -+ regulator-max-microvolt = <1450000>; -+ regulator-ramp-delay = <12500>; -+ -+ regulator-state-mem { -+ regulator-on-in-suspend; -+ regulator-suspend-microvolt = <950000>; -+ }; -+ }; -+ -+ vcc_ddr: DCDC_REG3 { -+ regulator-name = "vcc_ddr"; -+ regulator-always-on; -+ regulator-boot-on; -+ -+ regulator-state-mem { -+ regulator-on-in-suspend; -+ }; -+ }; -+ -+ vcc_io_33: DCDC_REG4 { -+ regulator-name = "vcc_io_33"; -+ regulator-always-on; -+ regulator-boot-on; -+ regulator-min-microvolt = <3300000>; -+ regulator-max-microvolt = <3300000>; -+ -+ regulator-state-mem { -+ regulator-on-in-suspend; -+ regulator-suspend-microvolt = <3300000>; -+ }; -+ }; -+ -+ vcc_18: LDO_REG1 { -+ regulator-name = "vcc_18"; -+ regulator-always-on; -+ regulator-boot-on; -+ regulator-min-microvolt = <1800000>; -+ regulator-max-microvolt = <1800000>; -+ -+ regulator-state-mem { -+ regulator-on-in-suspend; -+ regulator-suspend-microvolt = <1800000>; -+ }; -+ }; -+ -+ vcc18_emmc: LDO_REG2 { -+ regulator-name = "vcc18_emmc"; -+ regulator-always-on; -+ regulator-boot-on; -+ regulator-min-microvolt = <1800000>; -+ regulator-max-microvolt = <1800000>; -+ -+ regulator-state-mem { -+ regulator-on-in-suspend; -+ regulator-suspend-microvolt = <1800000>; -+ }; -+ }; -+ -+ vdd_10: LDO_REG3 { -+ regulator-name = "vdd_10"; -+ regulator-always-on; -+ regulator-boot-on; -+ regulator-min-microvolt = <1000000>; -+ regulator-max-microvolt = <1000000>; -+ -+ regulator-state-mem { -+ regulator-on-in-suspend; -+ regulator-suspend-microvolt = <1000000>; -+ }; -+ }; -+ }; -+ }; -+}; -+ -+&io_domains { -+ pmuio-supply = <&vcc_io_33>; -+ vccio1-supply = <&vcc_io_33>; -+ vccio2-supply = <&vcc18_emmc>; -+ vccio3-supply = <&vcc_io_sdio>; -+ vccio4-supply = <&vcc_18>; -+ vccio5-supply = <&vcc_io_33>; -+ vccio6-supply = <&vcc_io_33>; -+ status = "okay"; -+}; -+ -+&pinctrl { -+ button { -+ reset_button_pin: reset-button-pin { -+ rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>; -+ }; -+ }; -+ -+ ethernet-phy { -+ eth_phy_reset_pin: eth-phy-reset-pin { -+ rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_down>; -+ }; -+ }; -+ -+ leds { -+ lan_led_pin: lan-led-pin { -+ rockchip,pins = <2 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>; -+ }; -+ -+ sys_led_pin: sys-led-pin { -+ rockchip,pins = <0 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>; -+ }; -+ -+ wan_led_pin: wan-led-pin { -+ rockchip,pins = <2 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>; -+ }; -+ }; -+ -+ pmic { -+ pmic_int_l: pmic-int-l { -+ rockchip,pins = <1 RK_PD0 RK_FUNC_GPIO &pcfg_pull_up>; -+ }; -+ }; -+ -+ sd { -+ sdio_vcc_pin: sdio-vcc-pin { -+ rockchip,pins = <1 RK_PD4 RK_FUNC_GPIO &pcfg_pull_up>; -+ }; -+ }; -+}; -+ -+&pwm2 { -+ status = "okay"; -+}; -+ -+&sdmmc { -+ bus-width = <4>; -+ cap-sd-highspeed; -+ disable-wp; -+ pinctrl-0 = <&sdmmc0_clk>, <&sdmmc0_cmd>, <&sdmmc0_dectn>, <&sdmmc0_bus4>; -+ pinctrl-names = "default"; -+ sd-uhs-sdr12; -+ sd-uhs-sdr25; -+ sd-uhs-sdr50; -+ sd-uhs-sdr104; -+ vmmc-supply = <&vcc_sd>; -+ vqmmc-supply = <&vcc_io_sdio>; -+ status = "okay"; -+}; -+ -+&tsadc { -+ rockchip,hw-tshut-mode = <0>; -+ rockchip,hw-tshut-polarity = <0>; -+ status = "okay"; -+}; -+ -+&u2phy { -+ status = "okay"; -+}; -+ -+&u2phy_host { -+ status = "okay"; -+}; -+ -+&u2phy_otg { -+ status = "okay"; -+}; -+ -+&uart2 { -+ status = "okay"; -+}; -+ -+&usb20_otg { -+ status = "okay"; -+ dr_mode = "host"; -+}; -+ -+&usb_host0_ehci { -+ status = "okay"; -+}; -+ -+&usb_host0_ohci { -+ status = "okay"; -+}; diff --git a/target/linux/rockchip/patches-5.4/004-arm64-dts-rockchip-Add-txpbl-node-for-RK3399-RK3328.patch b/target/linux/rockchip/patches-5.4/004-arm64-dts-rockchip-Add-txpbl-node-for-RK3399-RK3328.patch deleted file mode 100644 index 83ce8f1efb..0000000000 --- a/target/linux/rockchip/patches-5.4/004-arm64-dts-rockchip-Add-txpbl-node-for-RK3399-RK3328.patch +++ /dev/null @@ -1,54 +0,0 @@ -From 8a469ee35606ba65448d54e5a2a23302f7e79e3c Mon Sep 17 00:00:00 2001 -From: Carlos de Paula -Date: Tue, 18 Feb 2020 17:10:37 -0500 -Subject: [PATCH] arm64: dts: rockchip: Add txpbl node for RK3399/RK3328 - -Some rockchip SoCs like the RK3399 and RK3328 exhibit an issue -where tx checksumming does not work with packets larger than 1498. - -The default Programmable Buffer Length for TX in these GMAC's is -not suitable for MTUs higher than 1498. The workaround is to disable -TX offloading with 'ethtool -K eth0 tx off rx off' causing performance -impacts as it disables hardware checksumming. - -This patch sets snps,txpbl to 0x4 which is a safe number tested ok for -the most popular MTU value of 1500. - -For reference, see https://lkml.org/lkml/2019/4/1/1382. - -Signed-off-by: Carlos de Paula -Link: https://lore.kernel.org/r/20200218221040.10955-1-me@carlosedp.com -Signed-off-by: Heiko Stuebner ---- - arch/arm64/boot/dts/rockchip/rk3328.dtsi | 2 ++ - arch/arm64/boot/dts/rockchip/rk3399.dtsi | 1 + - 2 files changed, 3 insertions(+) - ---- a/arch/arm64/boot/dts/rockchip/rk3328.dtsi -+++ b/arch/arm64/boot/dts/rockchip/rk3328.dtsi -@@ -857,6 +857,7 @@ - resets = <&cru SRST_GMAC2IO_A>; - reset-names = "stmmaceth"; - rockchip,grf = <&grf>; -+ snps,txpbl = <0x4>; - status = "disabled"; - }; - -@@ -878,6 +879,7 @@ - reset-names = "stmmaceth", "mac-phy"; - phy-mode = "rmii"; - phy-handle = <&phy>; -+ snps,txpbl = <0x4>; - status = "disabled"; - - mdio { ---- a/arch/arm64/boot/dts/rockchip/rk3399.dtsi -+++ b/arch/arm64/boot/dts/rockchip/rk3399.dtsi -@@ -291,6 +291,7 @@ - resets = <&cru SRST_A_GMAC>; - reset-names = "stmmaceth"; - rockchip,grf = <&grf>; -+ snps,txpbl = <0x4>; - status = "disabled"; - }; - diff --git a/target/linux/rockchip/patches-5.4/005-rockchip-rk3328-add-compatible-to-NanoPi-R2S-etherne.patch b/target/linux/rockchip/patches-5.4/005-rockchip-rk3328-add-compatible-to-NanoPi-R2S-etherne.patch deleted file mode 100644 index 897a42fea2..0000000000 --- a/target/linux/rockchip/patches-5.4/005-rockchip-rk3328-add-compatible-to-NanoPi-R2S-etherne.patch +++ /dev/null @@ -1,25 +0,0 @@ -From bc6c96d850419e71dbc9b0094ccc9b668ba9be43 Mon Sep 17 00:00:00 2001 -From: David Bauer -Date: Mon, 28 Sep 2020 22:54:52 +0200 -Subject: [PATCH] rockchip: rk3328: add compatible to NanoPi R2S ethernet PHY - -This adds the compatible property to the NanoPi R2S ethernet PHY node. -Otherwise, the PHY might not be probed, as the PHY ID reads all 0xff -when it is still in reset. - -Signed-off-by: David Bauer ---- - arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts | 2 ++ - 1 file changed, 2 insertions(+) - ---- a/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts -+++ b/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts -@@ -134,6 +134,8 @@ - #size-cells = <0>; - - rtl8211e: ethernet-phy@1 { -+ compatible = "ethernet-phy-id001c.c915", -+ "ethernet-phy-ieee802.3-c22"; - reg = <1>; - pinctrl-0 = <ð_phy_reset_pin>; - pinctrl-names = "default"; diff --git a/target/linux/rockchip/patches-5.4/006-rockchip-rk3328-fix-NanoPi-R2S-GMAC-clock-name.patch b/target/linux/rockchip/patches-5.4/006-rockchip-rk3328-fix-NanoPi-R2S-GMAC-clock-name.patch deleted file mode 100644 index 15c8ad71a6..0000000000 --- a/target/linux/rockchip/patches-5.4/006-rockchip-rk3328-fix-NanoPi-R2S-GMAC-clock-name.patch +++ /dev/null @@ -1,27 +0,0 @@ -From f2962ed3805c5b74948d00e4e6fbb33388261ba8 Mon Sep 17 00:00:00 2001 -From: David Bauer -Date: Sun, 4 Oct 2020 16:43:29 +0200 -Subject: [PATCH] rockchip: rk3328: fix NanoPi R2S GMAC clock name - -This commit fixes the name for the GMAC clock to gmac_clkin, as this is -the name of the clock provided by the rk3328-clk driver. - -Without this commit, the GMAC will not work in TX direction. - -Suggested-by: Tobias Waldvogel -Signed-off-by: David Bauer ---- - arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts | 2 +- - 1 file changed, 1 insertion(+), 1 deletion(-) - ---- a/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts -+++ b/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts -@@ -20,7 +20,7 @@ - gmac_clk: gmac-clock { - compatible = "fixed-clock"; - clock-frequency = <125000000>; -- clock-output-names = "gmac_clk"; -+ clock-output-names = "gmac_clkin"; - #clock-cells = <0>; - }; - diff --git a/target/linux/rockchip/patches-5.4/007-v5.13-rockchip-rk3399-Add-support-for-FriendlyARM-NanoPi-R.patch b/target/linux/rockchip/patches-5.4/007-v5.13-rockchip-rk3399-Add-support-for-FriendlyARM-NanoPi-R.patch deleted file mode 100644 index c508d71317..0000000000 --- a/target/linux/rockchip/patches-5.4/007-v5.13-rockchip-rk3399-Add-support-for-FriendlyARM-NanoPi-R.patch +++ /dev/null @@ -1,177 +0,0 @@ -From db792e9adbf85ffc9d6b0b060ac3c8e3148c8992 Mon Sep 17 00:00:00 2001 -From: Tianling Shen -Date: Fri, 19 Mar 2021 13:16:27 +0800 -Subject: [PATCH] rockchip: rk3399: Add support for FriendlyARM NanoPi R4S - -This adds support for the NanoPi R4S from FriendlyArm. - -Rockchip RK3399 SoC -1GB DDR3 or 4GB LPDDR4 RAM -Gigabit Ethernet (WAN) -Gigabit Ethernet (PCIe) (LAN) -USB 3.0 Port x 2 -MicroSD slot -Reset button -WAN - LAN - SYS LED - -Co-developed-by: Jensen Huang -Signed-off-by: Jensen Huang -[minor adjustments] -Co-developed-by: Marty Jones -Signed-off-by: Marty Jones -[further adjustments, fixed format issues] -Signed-off-by: Tianling Shen -Link: https://lore.kernel.org/r/20210319051627.814-2-cnsztl@gmail.com -Signed-off-by: Heiko Stuebner ---- - arch/arm64/boot/dts/rockchip/Makefile | 1 + - .../boot/dts/rockchip/rk3399-nanopi-r4s.dts | 133 +++++++++++++++++++++ - 2 files changed, 134 insertions(+) - create mode 100644 arch/arm64/boot/dts/rockchip/rk3399-nanopi-r4s.dts - ---- a/arch/arm64/boot/dts/rockchip/Makefile -+++ b/arch/arm64/boot/dts/rockchip/Makefile -@@ -25,6 +25,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-le - dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopc-t4.dtb - dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopi-m4.dtb - dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopi-neo4.dtb -+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopi-r4s.dtb - dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-orangepi.dtb - dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-puma-haikou.dtb - dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-roc-pc.dtb ---- /dev/null -+++ b/arch/arm64/boot/dts/rockchip/rk3399-nanopi-r4s.dts -@@ -0,0 +1,133 @@ -+// SPDX-License-Identifier: (GPL-2.0+ OR MIT) -+/* -+ * FriendlyElec NanoPC-T4 board device tree source -+ * -+ * Copyright (c) 2020 FriendlyElec Computer Tech. Co., Ltd. -+ * (http://www.friendlyarm.com) -+ * -+ * Copyright (c) 2018 Collabora Ltd. -+ * -+ * Copyright (c) 2020 Jensen Huang -+ * Copyright (c) 2020 Marty Jones -+ * Copyright (c) 2021 Tianling Shen -+ */ -+ -+/dts-v1/; -+#include "rk3399-nanopi4.dtsi" -+ -+/ { -+ model = "FriendlyElec NanoPi R4S"; -+ compatible = "friendlyarm,nanopi-r4s", "rockchip,rk3399"; -+ -+ /delete-node/ display-subsystem; -+ -+ gpio-leds { -+ pinctrl-0 = <&lan_led_pin>, <&sys_led_pin>, <&wan_led_pin>; -+ -+ /delete-node/ status; -+ -+ lan_led: led-lan { -+ gpios = <&gpio1 RK_PA1 GPIO_ACTIVE_HIGH>; -+ label = "green:lan"; -+ }; -+ -+ sys_led: led-sys { -+ gpios = <&gpio0 RK_PB5 GPIO_ACTIVE_HIGH>; -+ label = "red:sys"; -+ default-state = "on"; -+ }; -+ -+ wan_led: led-wan { -+ gpios = <&gpio1 RK_PA0 GPIO_ACTIVE_HIGH>; -+ label = "green:wan"; -+ }; -+ }; -+ -+ gpio-keys { -+ pinctrl-0 = <&reset_button_pin>; -+ -+ /delete-node/ power; -+ -+ reset { -+ debounce-interval = <50>; -+ gpios = <&gpio1 RK_PC6 GPIO_ACTIVE_LOW>; -+ label = "reset"; -+ linux,code = ; -+ }; -+ }; -+ -+ vdd_5v: vdd-5v { -+ compatible = "regulator-fixed"; -+ regulator-name = "vdd_5v"; -+ regulator-always-on; -+ regulator-boot-on; -+ }; -+}; -+ -+&emmc_phy { -+ status = "disabled"; -+}; -+ -+&i2c4 { -+ status = "disabled"; -+}; -+ -+&pcie0 { -+ max-link-speed = <1>; -+ num-lanes = <1>; -+ vpcie3v3-supply = <&vcc3v3_sys>; -+}; -+ -+&pinctrl { -+ gpio-leds { -+ /delete-node/ leds-gpio; -+ -+ lan_led_pin: lan-led-pin { -+ rockchip,pins = <1 RK_PA1 RK_FUNC_GPIO &pcfg_pull_none>; -+ }; -+ -+ sys_led_pin: sys-led-pin { -+ rockchip,pins = <0 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>; -+ }; -+ -+ wan_led_pin: wan-led-pin { -+ rockchip,pins = <1 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>; -+ }; -+ }; -+ -+ rockchip-key { -+ /delete-node/ power-key; -+ -+ reset_button_pin: reset-button-pin { -+ rockchip,pins = <1 RK_PC6 RK_FUNC_GPIO &pcfg_pull_up>; -+ }; -+ }; -+}; -+ -+&sdhci { -+ status = "disabled"; -+}; -+ -+&sdio0 { -+ status = "disabled"; -+}; -+ -+&u2phy0_host { -+ phy-supply = <&vdd_5v>; -+}; -+ -+&u2phy1_host { -+ status = "disabled"; -+}; -+ -+&uart0 { -+ status = "disabled"; -+}; -+ -+&usbdrd_dwc3_0 { -+ dr_mode = "host"; -+}; -+ -+&vcc3v3_sys { -+ vin-supply = <&vcc5v0_sys>; -+}; diff --git a/target/linux/rockchip/patches-5.4/008-arm64-dts-rockchip-add-EEPROM-node-for-NanoPi-R4S.patch b/target/linux/rockchip/patches-5.4/008-arm64-dts-rockchip-add-EEPROM-node-for-NanoPi-R4S.patch deleted file mode 100644 index 792028b292..0000000000 --- a/target/linux/rockchip/patches-5.4/008-arm64-dts-rockchip-add-EEPROM-node-for-NanoPi-R4S.patch +++ /dev/null @@ -1,31 +0,0 @@ -From af20b3384e8723077cc6484160b0cf4e9be321de Mon Sep 17 00:00:00 2001 -From: Tianling Shen -Date: Mon, 7 Jun 2021 15:45:37 +0800 -Subject: [PATCH] arm64: dts: rockchip: add EEPROM node for NanoPi R4S - -NanoPi R4S has a EEPROM attached to the 2nd I2C bus (U92), which -stores the MAC address. - -Signed-off-by: Tianling Shen ---- - arch/arm64/boot/dts/rockchip/rk3399-nanopi-r4s.dts | 9 +++++++++ - 1 file changed, 9 insertions(+) - ---- a/arch/arm64/boot/dts/rockchip/rk3399-nanopi-r4s.dts -+++ b/arch/arm64/boot/dts/rockchip/rk3399-nanopi-r4s.dts -@@ -68,6 +68,15 @@ - status = "disabled"; - }; - -+&i2c2 { -+ eeprom@51 { -+ compatible = "microchip,24c02", "atmel,24c02"; -+ reg = <0x51>; -+ pagesize = <16>; -+ read-only; /* This holds our MAC */ -+ }; -+}; -+ - &i2c4 { - status = "disabled"; - }; diff --git a/target/linux/rockchip/patches-5.4/100-rockchip-use-system-LED-for-OpenWrt.patch b/target/linux/rockchip/patches-5.4/100-rockchip-use-system-LED-for-OpenWrt.patch deleted file mode 100644 index 7b3b50ffd8..0000000000 --- a/target/linux/rockchip/patches-5.4/100-rockchip-use-system-LED-for-OpenWrt.patch +++ /dev/null @@ -1,31 +0,0 @@ -From 6731d2c9039fbe1ecf21915eab3acee0a999508a Mon Sep 17 00:00:00 2001 -From: David Bauer -Date: Fri, 10 Jul 2020 21:38:20 +0200 -Subject: [PATCH] rockchip: use system LED for OpenWrt - -Use the SYS LED on the casing for showing system status. - -This patch is kept separate from the NanoPi R2S support patch, as i plan -on submitting the device support upstream. - -Signed-off-by: David Bauer ---- - arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts | 9 ++++++++- - 1 file changed, 8 insertions(+), 1 deletion(-) - ---- a/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts -+++ b/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts -@@ -13,6 +13,13 @@ - model = "FriendlyElec NanoPi R2S"; - compatible = "friendlyarm,nanopi-r2s", "rockchip,rk3328"; - -+ aliases { -+ led-boot = &sys_led; -+ led-failsafe = &sys_led; -+ led-running = &sys_led; -+ led-upgrade = &sys_led; -+ }; -+ - chosen { - stdout-path = "serial2:1500000n8"; - }; diff --git a/target/linux/rockchip/patches-5.4/101-dts-rockchip-add-usb3-controller-node-for-RK3328-SoCs.patch b/target/linux/rockchip/patches-5.4/101-dts-rockchip-add-usb3-controller-node-for-RK3328-SoCs.patch deleted file mode 100644 index 2635c7a676..0000000000 --- a/target/linux/rockchip/patches-5.4/101-dts-rockchip-add-usb3-controller-node-for-RK3328-SoCs.patch +++ /dev/null @@ -1,62 +0,0 @@ -From: William Wu - -RK3328 has one USB 3.0 OTG controller which uses DWC_USB3 -core's general architecture. It can act as static xHCI host -controller, static device controller, USB 3.0/2.0 OTG basing -on ID of USB3.0 PHY. - -Signed-off-by: William Wu -Signed-off-by: Leonidas P. Papadakos - ---- - -NOTE: This binding still has issues. From the original thread: - -the rk3328 usb3-phy has an issue with detecting any plugin events -after a previous device got removed - see the inno-usb3-phy driver -in the vendor kernel. - -The current state is good-enough for enabling the USB3 attached LAN -port of the NanoPi R2S. However, it might explode depending on your -use-case. You've been warned. - ---- - arch/arm64/boot/dts/rockchip/rk3328.dtsi | 27 ++++++++++++++++++++++++ - 1 file changed, 27 insertions(+) - ---- a/arch/arm64/boot/dts/rockchip/rk3328.dtsi -+++ b/arch/arm64/boot/dts/rockchip/rk3328.dtsi -@@ -938,6 +938,33 @@ - status = "disabled"; - }; - -+ usbdrd3: usb@ff600000 { -+ compatible = "rockchip,rk3328-dwc3", "rockchip,rk3399-dwc3"; -+ clocks = <&cru SCLK_USB3OTG_REF>, <&cru SCLK_USB3OTG_SUSPEND>, -+ <&cru ACLK_USB3OTG>; -+ clock-names = "ref_clk", "suspend_clk", -+ "bus_clk"; -+ #address-cells = <2>; -+ #size-cells = <2>; -+ ranges; -+ status = "disabled"; -+ -+ usbdrd_dwc3: dwc3@ff600000 { -+ compatible = "snps,dwc3"; -+ reg = <0x0 0xff600000 0x0 0x100000>; -+ interrupts = ; -+ dr_mode = "otg"; -+ phy_type = "utmi_wide"; -+ snps,dis_enblslpm_quirk; -+ snps,dis-u2-freeclk-exists-quirk; -+ snps,dis_u2_susphy_quirk; -+ snps,dis_u3_susphy_quirk; -+ snps,dis-del-phy-power-chg-quirk; -+ snps,dis-tx-ipgap-linecheck-quirk; -+ status = "disabled"; -+ }; -+ }; -+ - gic: interrupt-controller@ff811000 { - compatible = "arm,gic-400"; - #interrupt-cells = <3>; diff --git a/target/linux/rockchip/patches-5.4/102-rockchip-enable-LAN-port-on-NanoPi-R2S.patch b/target/linux/rockchip/patches-5.4/102-rockchip-enable-LAN-port-on-NanoPi-R2S.patch deleted file mode 100644 index 243c1ac78d..0000000000 --- a/target/linux/rockchip/patches-5.4/102-rockchip-enable-LAN-port-on-NanoPi-R2S.patch +++ /dev/null @@ -1,60 +0,0 @@ -From 0fc3b9b7619c4878f73a6a7989863f0d1a3fd392 Mon Sep 17 00:00:00 2001 -From: David Bauer -Date: Fri, 10 Jul 2020 21:12:16 +0200 -Subject: [PATCH] rockchip: enabled LAN port on NanoPi R2S - -Enable the USB3 port on the FriendlyARM NanoPi R2S. -This is required for the USB3 attached LAN port to work. - -Signed-off-by: David Bauer ---- - .../boot/dts/rockchip/rk3328-nanopi-r2s.dts | 27 +++++++++++++++++++ - 1 file changed, 27 insertions(+) - ---- a/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts -+++ b/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts -@@ -44,6 +44,18 @@ - }; - }; - -+ vcc_rtl8153: vcc-rtl8153-regulator { -+ compatible = "regulator-fixed"; -+ gpio = <&gpio2 RK_PC6 GPIO_ACTIVE_HIGH>; -+ pinctrl-names = "default"; -+ pinctrl-0 = <&rtl8153_en_drv>; -+ regulator-always-on; -+ regulator-name = "vcc_rtl8153"; -+ regulator-min-microvolt = <5000000>; -+ regulator-max-microvolt = <5000000>; -+ enable-active-high; -+ }; -+ - leds { - compatible = "gpio-leds"; - pinctrl-0 = <&lan_led_pin>, <&sys_led_pin>, <&wan_led_pin>; -@@ -269,6 +281,12 @@ - }; - }; - }; -+ -+ usb { -+ rtl8153_en_drv: rtl8153-en-drv { -+ rockchip,pins = <2 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>; -+ }; -+ }; - }; - - &io_domains { -@@ -375,3 +393,12 @@ - &usb_host0_ohci { - status = "okay"; - }; -+ -+&usbdrd3 { -+ status = "okay"; -+}; -+ -+&usbdrd_dwc3 { -+ dr_mode = "host"; -+ status = "okay"; -+}; diff --git a/target/linux/rockchip/patches-5.4/103-arm64-rockchip-add-OF-node-for-USB-eth-on-NanoPi-R2S.patch b/target/linux/rockchip/patches-5.4/103-arm64-rockchip-add-OF-node-for-USB-eth-on-NanoPi-R2S.patch deleted file mode 100644 index e318f3136f..0000000000 --- a/target/linux/rockchip/patches-5.4/103-arm64-rockchip-add-OF-node-for-USB-eth-on-NanoPi-R2S.patch +++ /dev/null @@ -1,28 +0,0 @@ -From 2795c8b31a686bdb8338f9404d18ef7a154f0d75 Mon Sep 17 00:00:00 2001 -From: David Bauer -Date: Sun, 26 Jul 2020 13:32:59 +0200 -Subject: [PATCH] arm64: rockchip: add OF node for USB eth on NanoPi R2S - -This adds the OF node for the USB3 ethernet adapter on the FriendlyARM -NanoPi R2S. Add the correct value for the RTL8153 LED configuration -register to match the blink behavior of the other port on the device. - -Signed-off-by: David Bauer ---- - arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts | 7 +++++++ - 1 file changed, 7 insertions(+) - ---- a/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts -+++ b/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts -@@ -401,4 +401,11 @@ - &usbdrd_dwc3 { - dr_mode = "host"; - status = "okay"; -+ -+ usb-eth@2 { -+ compatible = "realtek,rtl8153"; -+ reg = <2>; -+ -+ realtek,led-data = <0x87>; -+ }; - }; diff --git a/target/linux/rockchip/patches-5.4/104-rockchip-use-USB-host-by-default-on-rk3399-rock-pi-4.patch b/target/linux/rockchip/patches-5.4/104-rockchip-use-USB-host-by-default-on-rk3399-rock-pi-4.patch deleted file mode 100644 index 1abab5e2eb..0000000000 --- a/target/linux/rockchip/patches-5.4/104-rockchip-use-USB-host-by-default-on-rk3399-rock-pi-4.patch +++ /dev/null @@ -1,32 +0,0 @@ -From e12f67fe83446432ef16704c22ec23bd1dbcd094 Mon Sep 17 00:00:00 2001 -From: Vicente Bergas -Date: Tue, 1 Dec 2020 16:41:32 +0100 -Subject: arm64: dts: rockchip: use USB host by default on rk3399-rock-pi-4 - -Based on the board schematics at -https://dl.radxa.com/rockpi4/docs/hw/rockpi4/rockpi_4c_v12_sch_20200620.pdf -on page 19 there is an USB Type-A receptacle being used as an USB-OTG port. - -But the Type-A connector is not valid for OTG operation, for this reason -there is a switch to select host or device role. -This is non-compliant and error prone because switching is manual. -So, use host mode as it corresponds for a Type-A receptacle. - -Signed-off-by: Vicente Bergas -Link: https://lore.kernel.org/r/20201201154132.1286-4-vicencb@gmail.com -Signed-off-by: Heiko Stuebner ---- - arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4.dts | 2 +- - 1 file changed, 1 insertion(+), 1 deletion(-) - ---- a/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4.dts -+++ b/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4.dts -@@ -684,7 +684,7 @@ - - &usbdrd_dwc3_0 { - status = "okay"; -- dr_mode = "otg"; -+ dr_mode = "host"; - }; - - &usbdrd3_1 { -- 2.30.2