From dc79b51533cfe9a7806353f6c6fd6b22cd80d536 Mon Sep 17 00:00:00 2001 From: Alexey Bartenev <41exey@proton.me> Date: Fri, 10 Mar 2023 10:35:30 -0500 Subject: [PATCH] ramips: add support for Keenetic Lite III rev. A MIME-Version: 1.0 Content-Type: text/plain; charset=utf8 Content-Transfer-Encoding: 8bit General specification: SoC Type: MediaTek MT7620N (580MHz) ROM: 8 MB SPI-NOR (W25Q64FV) RAM: 64 MB DDR (EM6AB160TSD-5G) Switch: MediaTek MT7530 Ethernet: 5 ports - 5×100MbE (WAN, LAN1-4) Wireless: 2.4 GHz (MediaTek RT5390): b/g/n Buttons: 3 button (POWER, RESET, WPS) Slide switch: 4 position (BASE, ADAPTER, BOOSTER, ACCESS POINT) Bootloader: U-Boot 1.1.3 Power: 9 VDC, 0.6 A MAC in stock: |- + | | LAN | RF-EEPROM + 0x04 | | WLAN | RF-EEPROM + 0x04 | | WAN | RF-EEPROM + 0x28 | OEM easy installation 1. Use a PC to browse to http://my.keenetic.net. 2. Go to the System section and open the Files tab. 3. Under the Files tab, there will be a list of system files. Click on the Firmware file. 4. When a modal window appears, click on the Choose File button and upload the firmware image. 5. Wait for the router to flash and reboot. OEM installation using the TFTP method 1. Download the latest firmware image and rename it to klite3_recovery.bin. 2. Set up a Tftp server on a PC (e.g. Tftpd32) and place the firmware image to the root directory of the server. 3. Power off the router and use a twisted pair cable to connect the PC to any of the router's LAN ports. 4. Configure the network adapter of the PC to use IP address 192.168.1.2 and subnet mask 255.255.255.0. 5. Power up the router while holding the reset button pressed. 6. Wait approximately for 5 seconds and then release the reset button. 7. The router should download the firmware via TFTP and complete flashing in a few minutes. After flashing is complete, use the PC to browse to http://192.168.1.1 or ssh to proceed with the configuration. Signed-off-by: Alexey Bartenev <41exey@proton.me> --- package/boot/uboot-envtools/files/ramips | 3 +- .../dts/mt7620n_zyxel_keenetic-lite-iii-a.dts | 144 ++++++++++++++++++ target/linux/ramips/image/mt7620.mk | 12 ++ .../mt7620/base-files/etc/board.d/01_leds | 1 + .../mt7620/base-files/etc/board.d/02_network | 6 + 5 files changed, 165 insertions(+), 1 deletion(-) create mode 100644 target/linux/ramips/dts/mt7620n_zyxel_keenetic-lite-iii-a.dts diff --git a/package/boot/uboot-envtools/files/ramips b/package/boot/uboot-envtools/files/ramips index 6a0256c568..bc56210036 100644 --- a/package/boot/uboot-envtools/files/ramips +++ b/package/boot/uboot-envtools/files/ramips @@ -19,7 +19,8 @@ alfa-network,r36m-e4g|\ alfa-network,tube-e4g|\ engenius,epg600|\ engenius,esr600h|\ -sitecom,wlr-4100-v1-002) +sitecom,wlr-4100-v1-002|\ +zyxel,keenetic-lite-iii-a) ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x1000" "0x1000" ;; arcadyan,we420223-99) diff --git a/target/linux/ramips/dts/mt7620n_zyxel_keenetic-lite-iii-a.dts b/target/linux/ramips/dts/mt7620n_zyxel_keenetic-lite-iii-a.dts new file mode 100644 index 0000000000..0d1c4696d7 --- /dev/null +++ b/target/linux/ramips/dts/mt7620n_zyxel_keenetic-lite-iii-a.dts @@ -0,0 +1,144 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "mt7620n.dtsi" + +#include +#include +#include + +/ { + compatible = "zyxel,keenetic-lite-iii-a", "ralink,mt7620n-soc"; + model = "ZyXEL Keenetic Lite III (rev. A)"; + + aliases { + led-boot = &led_wan; + led-failsafe = &led_wan; + led-running = &led_wan; + led-upgrade = &led_wan; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&gpio0 1 GPIO_ACTIVE_LOW>; // #GPIO1 + linux,code = ; + }; + + wps { + label = "wps"; + gpios = <&gpio0 2 GPIO_ACTIVE_LOW>; // #GPIO2 + linux,code = ; + }; + + sw0 { + label = "sw0"; + gpios = <&gpio0 17 GPIO_ACTIVE_LOW>; // #GPIO17 + linux,code = ; + }; + + sw1 { + label = "sw1"; + gpios = <&gpio0 20 GPIO_ACTIVE_LOW>; // #GPIO20 + linux,code = ; + }; + + sw2 { + label = "sw2"; + gpios = <&gpio0 21 GPIO_ACTIVE_LOW>; // #GPIO21 + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_wan: wan { + label = "green:wan"; + color = ; + function = LED_FUNCTION_STATUS; + gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; // #GPIO38 + }; + + wifi { + label = "green:wifi"; + color = ; + function = LED_FUNCTION_WLAN; + gpios = <&gpio3 0 GPIO_ACTIVE_HIGH>; // #GPIO72 + }; + }; + +}; + +&gpio0 { + status = "okay"; +}; + +&gpio1 { + status = "okay"; +}; + +&gpio3 { + status = "okay"; +}; + +&spi0 { + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <48000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "U-Boot"; + reg = <0x0 0x30000>; + read-only; + }; + + partition@30000 { + label = "U-Config"; + reg = <0x30000 0x10000>; + }; + + factory: partition@40000 { + label = "RF-EEPROM"; + reg = <0x40000 0x10000>; + read-only; + }; + + partition@50000 { + compatible = "denx,uimage"; + label = "firmware"; + reg = <0x50000 0x7a0000>; + }; + + partition@7f0000 { + label = "Config"; + reg = <0x7f0000 0x10000>; + }; + + partition@0_1 { + label = "Full"; + reg = <0x0 0x800000>; + }; + }; + }; +}; + +&state_default { + gpio { + groups = "i2c"; + function = "gpio"; + }; +}; + +&wmac { + ralink,mtd-eeprom = <&factory 0x0>; +}; diff --git a/target/linux/ramips/image/mt7620.mk b/target/linux/ramips/image/mt7620.mk index 6e528a930b..de84b232c1 100644 --- a/target/linux/ramips/image/mt7620.mk +++ b/target/linux/ramips/image/mt7620.mk @@ -1471,6 +1471,18 @@ define Device/zte_q7 endef TARGET_DEVICES += zte_q7 +define Device/zyxel_keenetic-lite-iii-a + SOC := mt7620n + IMAGE_SIZE := 7872k + DEVICE_VENDOR := ZyXEL + DEVICE_MODEL := Keenetic Lite III + DEVICE_VARIANT := A + IMAGES += factory.bin + IMAGE/factory.bin := $$(sysupgrade_bin) | pad-to 64k | check-size | \ + zyimage -d 2102018 -v "ZyXEL Keenetic Lite III" +endef +TARGET_DEVICES += zyxel_keenetic-lite-iii-a + define Device/zyxel_keenetic-omni SOC := mt7620n IMAGE_SIZE := 7872k diff --git a/target/linux/ramips/mt7620/base-files/etc/board.d/01_leds b/target/linux/ramips/mt7620/base-files/etc/board.d/01_leds index 36e3045a38..2deda0861a 100644 --- a/target/linux/ramips/mt7620/base-files/etc/board.d/01_leds +++ b/target/linux/ramips/mt7620/base-files/etc/board.d/01_leds @@ -55,6 +55,7 @@ planex,mzk-ex300np|\ zbtlink,zbt-we826-16m|\ zbtlink,zbt-we826-32m|\ zbtlink,zbt-wr8305rt|\ +zyxel,keenetic-lite-iii-a|\ zyxel,keenetic-omni|\ zyxel,keenetic-omni-ii|\ zyxel,keenetic-viva) diff --git a/target/linux/ramips/mt7620/base-files/etc/board.d/02_network b/target/linux/ramips/mt7620/base-files/etc/board.d/02_network index 992d8a9c40..787e123e31 100644 --- a/target/linux/ramips/mt7620/base-files/etc/board.d/02_network +++ b/target/linux/ramips/mt7620/base-files/etc/board.d/02_network @@ -28,6 +28,7 @@ ramips_setup_interfaces() zbtlink,zbt-we826-32m|\ zbtlink,zbt-we826-e|\ zbtlink,zbt-wr8305rt|\ + zyxel,keenetic-lite-iii-a|\ zyxel,keenetic-omni) ucidef_add_switch "switch0" \ "0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "6@eth0" @@ -404,6 +405,11 @@ ramips_setup_macs() zbtlink,zbt-we1026-5g-16m) label_mac=$(mtd_get_mac_binary factory 0x4) ;; + zyxel,keenetic-lite-iii-a) + lan_mac=$(mtd_get_mac_binary RF-EEPROM 0x4) + wan_mac=$(mtd_get_mac_binary RF-EEPROM 0x28) + label_mac=$wan_mac + ;; zyxel,keenetic-omni|\ zyxel,keenetic-omni-ii|\ zyxel,keenetic-viva) -- 2.30.2