From d9b94f28a442b0013caef99de084d7b72e2d4607 Mon Sep 17 00:00:00 2001 From: Jon Loeliger Date: Mon, 25 Jul 2005 14:05:07 -0500 Subject: [PATCH] * Patch by Jon Loeliger, 2005-05-05 Implemented support for MPC8548CDS board. Added DDR II support based on SPD values for MPC85xx boards. This roll-up patch also includes bugfies for the previously published patches: DDRII CPO, pre eTSEC, 8548 LBIU, Andy's TSEC, eTSEC 3&4 I/O --- CHANGELOG | 7 + MAKEALL | 7 +- Makefile | 3 + board/cds/mpc8541cds/mpc8541cds.c | 4 +- board/cds/mpc8548cds/Makefile | 51 ++ board/cds/mpc8548cds/config.mk | 30 + board/cds/mpc8548cds/init.S | 255 +++++++ board/cds/mpc8548cds/mpc8548cds.c | 329 +++++++++ board/cds/mpc8548cds/u-boot.lds | 147 ++++ board/cds/mpc8555cds/mpc8555cds.c | 4 +- board/mpc8540ads/mpc8540ads.c | 4 +- board/mpc8560ads/mpc8560ads.c | 4 +- cpu/mpc85xx/cpu.c | 21 +- cpu/mpc85xx/cpu_init.c | 42 +- cpu/mpc85xx/spd_sdram.c | 1096 +++++++++++++++++++++++------ cpu/mpc85xx/start.S | 6 + cpu/mpc85xx/tsec.c | 48 +- cpu/mpc85xx/tsec.h | 10 +- doc/README.mpc85xxads | 9 +- doc/README.mpc85xxcds | 43 +- include/asm-ppc/immap_85xx.h | 35 +- include/asm-ppc/processor.h | 4 + include/configs/MPC8540ADS.h | 10 +- include/configs/MPC8541CDS.h | 13 +- include/configs/MPC8548CDS.h | 521 ++++++++++++++ include/configs/MPC8555CDS.h | 13 +- include/configs/MPC8560ADS.h | 10 +- include/configs/PM854.h | 10 +- include/configs/SBC8540.h | 12 +- include/configs/SBC8560.h | 12 +- include/configs/TQM8540.h | 6 +- include/configs/TQM8560.h | 3 +- include/configs/sbc8560.h | 12 +- include/configs/stxgp3.h | 4 +- include/spd.h | 126 ++-- net/eth.c | 15 +- 36 files changed, 2573 insertions(+), 353 deletions(-) create mode 100644 board/cds/mpc8548cds/Makefile create mode 100644 board/cds/mpc8548cds/config.mk create mode 100644 board/cds/mpc8548cds/init.S create mode 100644 board/cds/mpc8548cds/mpc8548cds.c create mode 100644 board/cds/mpc8548cds/u-boot.lds create mode 100644 include/configs/MPC8548CDS.h diff --git a/CHANGELOG b/CHANGELOG index 39166f8c7e..2213bf068a 100644 --- a/CHANGELOG +++ b/CHANGELOG @@ -1,6 +1,13 @@ ====================================================================== Changes for U-Boot 1.1.3: ====================================================================== +* Patch by Jon Loeliger, 2005-05-05 + Implemented support for MPC8548CDS board. + Added DDR II support based on SPD values for MPC85xx boards. + This roll-up patch also includes bugfies for the previously + published patches: + DDRII CPO, pre eTSEC, 8548 LBIU, Andy's TSEC, eTSEC 3&4 I/O + * Patch by Jon Loeliger, 2005-Feb-10 Add config option CONFIG_HAS_FEC calling out 8540 FEC features. diff --git a/MAKEALL b/MAKEALL index e9f93076d4..26d0ac9d74 100755 --- a/MAKEALL +++ b/MAKEALL @@ -111,9 +111,10 @@ LIST_8260=" \ ######################################################################### LIST_85xx=" \ - MPC8540ADS MPC8541CDS MPC8555CDS MPC8560ADS \ - PM854 sbc8540 sbc8560 stxgp3 \ - TQM8540 \ + + MPC8540ADS MPC8541CDS MPC8548CDS MPC8555CDS \ + MPC8560ADS PM854 sbc8540 sbc8560 \ + stxgp3 TQM8540 \ " ######################################################################### diff --git a/Makefile b/Makefile index e7b36ab6b9..943cfbf347 100644 --- a/Makefile +++ b/Makefile @@ -1193,6 +1193,9 @@ MPC8560ADS_config: unconfig MPC8541CDS_config: unconfig @./mkconfig $(@:_config=) ppc mpc85xx mpc8541cds cds +MPC8548CDS_config: unconfig + @./mkconfig $(@:_config=) ppc mpc85xx mpc8548cds cds + MPC8555CDS_config: unconfig @./mkconfig $(@:_config=) ppc mpc85xx mpc8555cds cds diff --git a/board/cds/mpc8541cds/mpc8541cds.c b/board/cds/mpc8541cds/mpc8541cds.c index c75a4dfe0f..6b8aa68f54 100644 --- a/board/cds/mpc8541cds/mpc8541cds.c +++ b/board/cds/mpc8541cds/mpc8541cds.c @@ -32,7 +32,7 @@ #include "../common/cadmus.h" #include "../common/eeprom.h" -#if defined(CONFIG_DDR_ECC) +#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER) extern void ddr_enable_ecc(unsigned int dram_size); #endif @@ -271,7 +271,7 @@ initdram(int board_type) #endif dram_size = spd_sdram(); -#if defined(CONFIG_DDR_ECC) +#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER) /* * Initialize and enable DDR ECC. */ diff --git a/board/cds/mpc8548cds/Makefile b/board/cds/mpc8548cds/Makefile new file mode 100644 index 0000000000..0d4abbd71d --- /dev/null +++ b/board/cds/mpc8548cds/Makefile @@ -0,0 +1,51 @@ +# +# Copyright 2004 Freescale Semiconductor. +# (C) Copyright 2001 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = lib$(BOARD).a + +OBJS := $(BOARD).o \ + ../common/cadmus.o \ + ../common/eeprom.o + +SOBJS := init.o + +$(LIB): $(OBJS) $(SOBJS) + $(AR) crv $@ $(OBJS) + +clean: + rm -f $(OBJS) $(SOBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +.depend: Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c) + $(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@ + +-include .depend + +######################################################################### diff --git a/board/cds/mpc8548cds/config.mk b/board/cds/mpc8548cds/config.mk new file mode 100644 index 0000000000..242a676200 --- /dev/null +++ b/board/cds/mpc8548cds/config.mk @@ -0,0 +1,30 @@ +# +# Copyright 2004 Freescale Semiconductor. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +# +# mpc8548cds board +# +TEXT_BASE = 0xfff80000 + +PLATFORM_CPPFLAGS += -DCONFIG_E500=1 +PLATFORM_CPPFLAGS += -DCONFIG_MPC85xx=1 +PLATFORM_CPPFLAGS += -DCONFIG_MPC8548=1 diff --git a/board/cds/mpc8548cds/init.S b/board/cds/mpc8548cds/init.S new file mode 100644 index 0000000000..53dcd0d762 --- /dev/null +++ b/board/cds/mpc8548cds/init.S @@ -0,0 +1,255 @@ +/* + * Copyright 2004 Freescale Semiconductor. + * Copyright 2002,2003, Motorola Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include +#include + + +/* + * TLB0 and TLB1 Entries + * + * Out of reset, TLB1's Entry 0 maps the highest 4K for CCSRBAR. + * However, CCSRBAR is then relocated to CFG_CCSRBAR right after + * these TLB entries are established. + * + * The TLB entries for DDR are dynamically setup in spd_sdram() + * and use TLB1 Entries 8 through 15 as needed according to the + * size of DDR memory. + * + * MAS0: tlbsel, esel, nv + * MAS1: valid, iprot, tid, ts, tsize + * MAS2: epn, sharen, x0, x1, w, i, m, g, e + * MAS3: rpn, u0-u3, ux, sx, uw, sw, ur, sr + */ + +#define entry_start \ + mflr r1 ; \ + bl 0f ; + +#define entry_end \ +0: mflr r0 ; \ + mtlr r1 ; \ + blr ; + + + .section .bootpg, "ax" + .globl tlb1_entry +tlb1_entry: + entry_start + + /* + * Number of TLB0 and TLB1 entries in the following table + */ + .long 13 + +#if (CFG_CCSRBAR_DEFAULT != CFG_CCSRBAR) + /* + * TLB0 4K Non-cacheable, guarded + * 0xff700000 4K Initial CCSRBAR mapping + * + * This ends up at a TLB0 Index==0 entry, and must not collide + * with other TLB0 Entries. + */ + .long TLB1_MAS0(0, 0, 0) + .long TLB1_MAS1(1, 0, 0, 0, 0) + .long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,1,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,0,1,0,1,0,1) +#else +#error("Update the number of table entries in tlb1_entry") +#endif + + /* + * TLB0 16K Cacheable, non-guarded + * 0xd001_0000 16K Temporary Global data for initialization + * + * Use four 4K TLB0 entries. These entries must be cacheable + * as they provide the bootstrap memory before the memory + * controler and real memory have been configured. + * + * These entries end up at TLB0 Indicies 0x10, 0x14, 0x18 and 0x1c, + * and must not collide with other TLB0 entries. + */ + .long TLB1_MAS0(0, 0, 0) + .long TLB1_MAS1(1, 0, 0, 0, 0) + .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR), + 0,0,0,0,0,0,0,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR), + 0,0,0,0,0,1,0,1,0,1) + + .long TLB1_MAS0(0, 0, 0) + .long TLB1_MAS1(1, 0, 0, 0, 0) + .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 4 * 1024), + 0,0,0,0,0,0,0,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 4 * 1024), + 0,0,0,0,0,1,0,1,0,1) + + .long TLB1_MAS0(0, 0, 0) + .long TLB1_MAS1(1, 0, 0, 0, 0) + .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 8 * 1024), + 0,0,0,0,0,0,0,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 8 * 1024), + 0,0,0,0,0,1,0,1,0,1) + + .long TLB1_MAS0(0, 0, 0) + .long TLB1_MAS1(1, 0, 0, 0, 0) + .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 12 * 1024), + 0,0,0,0,0,0,0,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 12 * 1024), + 0,0,0,0,0,1,0,1,0,1) + + + /* + * TLB 0: 16M Non-cacheable, guarded + * 0xff000000 16M FLASH + * Out of reset this entry is only 4K. + */ + .long TLB1_MAS0(1, 0, 0) + .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16M) + .long TLB1_MAS2(E500_TLB_EPN(CFG_FLASH_BASE), 0,0,0,0,1,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_FLASH_BASE), 0,0,0,0,0,1,0,1,0,1) + + /* + * TLB 1: 256M Non-cacheable, guarded + * 0x80000000 256M PCI1 MEM First half + */ + .long TLB1_MAS0(1, 1, 0) + .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE), 0,0,0,0,1,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE), 0,0,0,0,0,1,0,1,0,1) + + /* + * TLB 2: 256M Non-cacheable, guarded + * 0x90000000 256M PCI1 MEM Second half + */ + .long TLB1_MAS0(1, 2, 0) + .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE + 0x10000000), + 0,0,0,0,1,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE + 0x10000000), + 0,0,0,0,0,1,0,1,0,1) + + /* + * TLB 3: 256M Non-cacheable, guarded + * 0xa0000000 256M PCI2 MEM First half + */ + .long TLB1_MAS0(1, 3, 0) + .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI2_MEM_BASE), 0,0,0,0,1,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI2_MEM_BASE), 0,0,0,0,0,1,0,1,0,1) + + /* + * TLB 4: 256M Non-cacheable, guarded + * 0xb0000000 256M PCI2 MEM Second half + */ + .long TLB1_MAS0(1, 4, 0) + .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI2_MEM_BASE + 0x10000000), + 0,0,0,0,1,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI2_MEM_BASE + 0x10000000), + 0,0,0,0,0,1,0,1,0,1) + + /* + * TLB 5: 64M Non-cacheable, guarded + * 0xe000_0000 1M CCSRBAR + * 0xe200_0000 16M PCI1 IO + * 0xe300_0000 16M PCI2 IO + */ + .long TLB1_MAS0(1, 5, 0) + .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR), 0,0,0,0,1,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR), 0,0,0,0,0,1,0,1,0,1) + + /* + * TLB 6: 64M Cacheable, non-guarded + * 0xf000_0000 64M LBC SDRAM + */ + .long TLB1_MAS0(1, 6, 0) + .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long TLB1_MAS2(E500_TLB_EPN(CFG_LBC_SDRAM_BASE), 0,0,0,0,0,0,0,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_LBC_SDRAM_BASE), 0,0,0,0,0,1,0,1,0,1) + + /* + * TLB 7: 1M Non-cacheable, guarded + * 0xf8000000 1M CADMUS registers + */ + .long TLB1_MAS0(1, 7, 0) + .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_1M) + .long TLB1_MAS2(E500_TLB_EPN(CADMUS_BASE_ADDR), 0,0,0,0,1,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CADMUS_BASE_ADDR), 0,0,0,0,0,1,0,1,0,1) + + entry_end + +/* + * LAW(Local Access Window) configuration: + * + * 0x0000_0000 0x7fff_ffff DDR 2G + * 0x8000_0000 0x9fff_ffff PCI1 MEM 512M + * 0xa000_0000 0xbfff_ffff PCI2 MEM 512M + * 0xe000_0000 0xe000_ffff CCSR 1M + * 0xe200_0000 0xe2ff_ffff PCI1 IO 16M + * 0xe300_0000 0xe3ff_ffff PCI2 IO 16M + * 0xf000_0000 0xf7ff_ffff SDRAM 128M + * 0xf800_0000 0xf80f_ffff NVRAM/CADMUS (*) 1M + * 0xff00_0000 0xff7f_ffff FLASH (2nd bank) 8M + * 0xff80_0000 0xffff_ffff FLASH (boot bank) 8M + * + * Notes: + * CCSRBAR and L2-as-SRAM don't need a configured Local Access Window. + * If flash is 8M at default position (last 8M), no LAW needed. + * + * The defines below are 1-off of the actual LAWAR0 usage. + * So LAWAR3 define uses the LAWAR4 register in the ECM. + */ + +#define LAWBAR0 0 +#define LAWAR0 ((LAWAR_TRGT_IF_DDR | (LAWAR_SIZE & LAWAR_SIZE_128M)) & ~LAWAR_EN) + +#define LAWBAR1 ((CFG_PCI1_MEM_BASE>>12) & 0xfffff) +#define LAWAR1 (LAWAR_EN | LAWAR_TRGT_IF_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_512M)) + +#define LAWBAR2 ((CFG_PCI2_MEM_BASE>>12) & 0xfffff) +#define LAWAR2 (LAWAR_EN | LAWAR_TRGT_IF_PCI2 | (LAWAR_SIZE & LAWAR_SIZE_512M)) + +#define LAWBAR3 ((CFG_PCI1_IO_BASE>>12) & 0xfffff) +#define LAWAR3 (LAWAR_EN | LAWAR_TRGT_IF_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_16M)) + +#define LAWBAR4 ((CFG_PCI2_IO_BASE>>12) & 0xfffff) +#define LAWAR4 (LAWAR_EN | LAWAR_TRGT_IF_PCI2 | (LAWAR_SIZE & LAWAR_SIZE_16M)) + +/* LBC window - maps 256M 0xf0000000 -> 0xffffffff */ +#define LAWBAR5 ((CFG_LBC_SDRAM_BASE>>12) & 0xfffff) +#define LAWAR5 (LAWAR_EN | LAWAR_TRGT_IF_LBC | (LAWAR_SIZE & LAWAR_SIZE_256M)) + + .section .bootpg, "ax" + .globl law_entry + +law_entry: + entry_start + .long 6 + .long LAWBAR0,LAWAR0,LAWBAR1,LAWAR1,LAWBAR2,LAWAR2,LAWBAR3,LAWAR3 + .long LAWBAR4,LAWAR4,LAWBAR5,LAWAR5 + entry_end diff --git a/board/cds/mpc8548cds/mpc8548cds.c b/board/cds/mpc8548cds/mpc8548cds.c new file mode 100644 index 0000000000..5bc08900a4 --- /dev/null +++ b/board/cds/mpc8548cds/mpc8548cds.c @@ -0,0 +1,329 @@ +/* + * Copyright 2004 Freescale Semiconductor. + * + * (C) Copyright 2002 Scott McNutt + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include + +#include "../common/cadmus.h" +#include "../common/eeprom.h" + +#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER) +extern void ddr_enable_ecc(unsigned int dram_size); +#endif + +extern long int spd_sdram(void); + +void local_bus_init(void); +void sdram_init(void); + +int board_early_init_f (void) +{ + return 0; +} + +int checkboard (void) +{ + volatile immap_t *immap = (immap_t *) CFG_CCSRBAR; + volatile ccsr_gur_t *gur = &immap->im_gur; + + /* PCI slot in USER bits CSR[6:7] by convention. */ + uint pci_slot = get_pci_slot (); + + uint pci_dual = get_pci_dual (); /* PCI DUAL in CM_PCI[3] */ + uint pci1_32 = gur->pordevsr & 0x10000; /* PORDEVSR[15] */ + uint pci1_clk_sel = gur->porpllsr & 0x8000; /* PORPLLSR[16] */ + uint pci2_clk_sel = gur->porpllsr & 0x4000; /* PORPLLSR[17] */ + + uint pci1_speed = get_clock_freq (); /* PCI PSPEED in [4:5] */ + + uint cpu_board_rev = get_cpu_board_revision (); + + printf ("Board: CDS Version 0x%02x, PCI Slot %d\n", + get_board_version (), pci_slot); + + printf ("CPU Board Revision %d.%d (0x%04x)\n", + MPC85XX_CPU_BOARD_MAJOR (cpu_board_rev), + MPC85XX_CPU_BOARD_MINOR (cpu_board_rev), cpu_board_rev); + + printf (" PCI1: %d bit, %s MHz, %s\n", + (pci1_32) ? 32 : 64, + (pci1_speed == 33000000) ? "33" : + (pci1_speed == 66000000) ? "66" : "unknown", + pci1_clk_sel ? "sync" : "async"); + + if (pci_dual) { + printf (" PCI2: 32 bit, 66 MHz, %s\n", + pci2_clk_sel ? "sync" : "async"); + } else { + printf (" PCI2: disabled\n"); + } + + /* + * Initialize local bus. + */ + local_bus_init (); + + + /* + * Hack TSEC 3 and 4 IO voltages. + */ + gur->tsec34ioovcr = 0xe7e0; /* 1110 0111 1110 0xxx */ + + return 0; +} + +long int +initdram(int board_type) +{ + long dram_size = 0; + volatile immap_t *immap = (immap_t *)CFG_IMMR; + + puts("Initializing\n"); + +#if defined(CONFIG_DDR_DLL) + { + /* + * Work around to stabilize DDR DLL MSYNC_IN. + * Errata DDR9 seems to have been fixed. + * This is now the workaround for Errata DDR11: + * Override DLL = 1, Course Adj = 1, Tap Select = 0 + */ + + volatile ccsr_gur_t *gur= &immap->im_gur; + + gur->ddrdllcr = 0x81000000; + asm("sync;isync;msync"); + udelay(200); + } +#endif + dram_size = spd_sdram(); + +#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER) + /* + * Initialize and enable DDR ECC. + */ + ddr_enable_ecc(dram_size); +#endif + /* + * SDRAM Initialization + */ + sdram_init(); + + puts(" DDR: "); + return dram_size; +} + +/* + * Initialize Local Bus + */ +void +local_bus_init(void) +{ + volatile immap_t *immap = (immap_t *)CFG_IMMR; + volatile ccsr_gur_t *gur = &immap->im_gur; + volatile ccsr_lbc_t *lbc = &immap->im_lbc; + + uint clkdiv; + uint lbc_hz; + sys_info_t sysinfo; + + get_sys_info(&sysinfo); + clkdiv = (lbc->lcrr & 0x0f) * 2; + lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv; + + gur->lbiuiplldcr1 = 0x00078080; + if (clkdiv == 16) { + gur->lbiuiplldcr0 = 0x7c0f1bf0; + } else if (clkdiv == 8) { + gur->lbiuiplldcr0 = 0x6c0f1bf0; + } else if (clkdiv == 4) { + gur->lbiuiplldcr0 = 0x5c0f1bf0; + } + + lbc->lcrr |= 0x00030000; + + asm("sync;isync;msync"); +} + +/* + * Initialize SDRAM memory on the Local Bus. + */ +void +sdram_init(void) +{ +#if defined(CFG_OR2_PRELIM) && defined(CFG_BR2_PRELIM) + + uint idx; + volatile immap_t *immap = (immap_t *)CFG_IMMR; + volatile ccsr_lbc_t *lbc = &immap->im_lbc; + uint *sdram_addr = (uint *)CFG_LBC_SDRAM_BASE; + uint cpu_board_rev; + uint lsdmr_common; + + puts(" SDRAM: "); + + print_size (CFG_LBC_SDRAM_SIZE * 1024 * 1024, "\n"); + + /* + * Setup SDRAM Base and Option Registers + */ + lbc->or2 = CFG_OR2_PRELIM; + asm("msync"); + + lbc->br2 = CFG_BR2_PRELIM; + asm("msync"); + + lbc->lbcr = CFG_LBC_LBCR; + asm("msync"); + + + lbc->lsrt = CFG_LBC_LSRT; + lbc->mrtpr = CFG_LBC_MRTPR; + asm("msync"); + + /* + * MPC8548 uses "new" 15-16 style addressing. + */ + cpu_board_rev = get_cpu_board_revision(); + lsdmr_common = CFG_LBC_LSDMR_COMMON; + lsdmr_common |= CFG_LBC_LSDMR_BSMA1516; + + /* + * Issue PRECHARGE ALL command. + */ + lbc->lsdmr = lsdmr_common | CFG_LBC_LSDMR_OP_PCHALL; + asm("sync;msync"); + *sdram_addr = 0xff; + ppcDcbf((unsigned long) sdram_addr); + udelay(100); + + /* + * Issue 8 AUTO REFRESH commands. + */ + for (idx = 0; idx < 8; idx++) { + lbc->lsdmr = lsdmr_common | CFG_LBC_LSDMR_OP_ARFRSH; + asm("sync;msync"); + *sdram_addr = 0xff; + ppcDcbf((unsigned long) sdram_addr); + udelay(100); + } + + /* + * Issue 8 MODE-set command. + */ + lbc->lsdmr = lsdmr_common | CFG_LBC_LSDMR_OP_MRW; + asm("sync;msync"); + *sdram_addr = 0xff; + ppcDcbf((unsigned long) sdram_addr); + udelay(100); + + /* + * Issue NORMAL OP command. + */ + lbc->lsdmr = lsdmr_common | CFG_LBC_LSDMR_OP_NORMAL; + asm("sync;msync"); + *sdram_addr = 0xff; + ppcDcbf((unsigned long) sdram_addr); + udelay(200); /* Overkill. Must wait > 200 bus cycles */ + +#endif /* enable SDRAM init */ +} + +#if defined(CFG_DRAM_TEST) +int +testdram(void) +{ + uint *pstart = (uint *) CFG_MEMTEST_START; + uint *pend = (uint *) CFG_MEMTEST_END; + uint *p; + + printf("Testing DRAM from 0x%08x to 0x%08x\n", + CFG_MEMTEST_START, + CFG_MEMTEST_END); + + printf("DRAM test phase 1:\n"); + for (p = pstart; p < pend; p++) + *p = 0xaaaaaaaa; + + for (p = pstart; p < pend; p++) { + if (*p != 0xaaaaaaaa) { + printf ("DRAM test fails at: %08x\n", (uint) p); + return 1; + } + } + + printf("DRAM test phase 2:\n"); + for (p = pstart; p < pend; p++) + *p = 0x55555555; + + for (p = pstart; p < pend; p++) { + if (*p != 0x55555555) { + printf ("DRAM test fails at: %08x\n", (uint) p); + return 1; + } + } + + printf("DRAM test passed.\n"); + return 0; +} +#endif + +#if defined(CONFIG_PCI) + +/* + * Initialize PCI Devices, report devices found. + */ + +#ifndef CONFIG_PCI_PNP +static struct pci_config_table pci_mpc85xxcds_config_table[] = { + { PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, + PCI_IDSEL_NUMBER, PCI_ANY_ID, + pci_cfgfunc_config_device, { PCI_ENET0_IOADDR, + PCI_ENET0_MEMADDR, + PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER + } }, + { } +}; +#endif + +static struct pci_controller hose = { +#ifndef CONFIG_PCI_PNP + config_table: pci_mpc85xxcds_config_table, +#endif +}; + +#endif /* CONFIG_PCI */ + +void +pci_init_board(void) +{ +#ifdef CONFIG_PCI + extern void pci_mpc85xx_init(struct pci_controller *hose); + + pci_mpc85xx_init(&hose); +#endif +} diff --git a/board/cds/mpc8548cds/u-boot.lds b/board/cds/mpc8548cds/u-boot.lds new file mode 100644 index 0000000000..91ea9fdd72 --- /dev/null +++ b/board/cds/mpc8548cds/u-boot.lds @@ -0,0 +1,147 @@ +/* + * Copyright 2004 Freescale Semiconductor. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_ARCH(powerpc) +SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib); +/* Do we need any of these for elf? + __DYNAMIC = 0; */ +SECTIONS +{ + .resetvec 0xFFFFFFFC : + { + *(.resetvec) + } = 0xffff + + .bootpg 0xFFFFF000 : + { + cpu/mpc85xx/start.o (.bootpg) + board/cds/mpc8548cds/init.o (.bootpg) + } = 0xffff + + /* Read-only sections, merged into text segment: */ + . = + SIZEOF_HEADERS; + .interp : { *(.interp) } + .hash : { *(.hash) } + .dynsym : { *(.dynsym) } + .dynstr : { *(.dynstr) } + .rel.text : { *(.rel.text) } + .rela.text : { *(.rela.text) } + .rel.data : { *(.rel.data) } + .rela.data : { *(.rela.data) } + .rel.rodata : { *(.rel.rodata) } + .rela.rodata : { *(.rela.rodata) } + .rel.got : { *(.rel.got) } + .rela.got : { *(.rela.got) } + .rel.ctors : { *(.rel.ctors) } + .rela.ctors : { *(.rela.ctors) } + .rel.dtors : { *(.rel.dtors) } + .rela.dtors : { *(.rela.dtors) } + .rel.bss : { *(.rel.bss) } + .rela.bss : { *(.rela.bss) } + .rel.plt : { *(.rel.plt) } + .rela.plt : { *(.rela.plt) } + .init : { *(.init) } + .plt : { *(.plt) } + .text : + { + cpu/mpc85xx/start.o (.text) + board/cds/mpc8548cds/init.o (.text) + cpu/mpc85xx/traps.o (.text) + cpu/mpc85xx/interrupts.o (.text) + cpu/mpc85xx/cpu_init.o (.text) + cpu/mpc85xx/cpu.o (.text) + cpu/mpc85xx/tsec.o (.text) + cpu/mpc85xx/speed.o (.text) + cpu/mpc85xx/pci.o (.text) + common/dlmalloc.o (.text) + lib_generic/crc32.o (.text) + lib_ppc/extable.o (.text) + lib_generic/zlib.o (.text) + *(.text) + *(.fixup) + *(.got1) + } + _etext = .; + PROVIDE (etext = .); + .rodata : + { + *(.rodata) + *(.rodata1) + *(.rodata.str1.4) + } + .fini : { *(.fini) } =0 + .ctors : { *(.ctors) } + .dtors : { *(.dtors) } + + /* Read-write section, merged into data segment: */ + . = (. + 0x00FF) & 0xFFFFFF00; + _erotext = .; + PROVIDE (erotext = .); + .reloc : + { + *(.got) + _GOT2_TABLE_ = .; + *(.got2) + _FIXUP_TABLE_ = .; + *(.fixup) + } + __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2; + __fixup_entries = (. - _FIXUP_TABLE_) >> 2; + + .data : + { + *(.data) + *(.data1) + *(.sdata) + *(.sdata2) + *(.dynamic) + CONSTRUCTORS + } + _edata = .; + PROVIDE (edata = .); + + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + __start___ex_table = .; + __ex_table : { *(__ex_table) } + __stop___ex_table = .; + + . = ALIGN(256); + __init_begin = .; + .text.init : { *(.text.init) } + .data.init : { *(.data.init) } + . = ALIGN(256); + __init_end = .; + + __bss_start = .; + .bss : + { + *(.sbss) *(.scommon) + *(.dynbss) + *(.bss) + *(COMMON) + } + _end = . ; + PROVIDE (end = .); +} diff --git a/board/cds/mpc8555cds/mpc8555cds.c b/board/cds/mpc8555cds/mpc8555cds.c index a40de2198b..18adf5b9e6 100644 --- a/board/cds/mpc8555cds/mpc8555cds.c +++ b/board/cds/mpc8555cds/mpc8555cds.c @@ -30,7 +30,7 @@ #include "../common/cadmus.h" #include "../common/eeprom.h" -#if defined(CONFIG_DDR_ECC) +#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER) extern void ddr_enable_ecc(unsigned int dram_size); #endif @@ -269,7 +269,7 @@ initdram(int board_type) #endif dram_size = spd_sdram(); -#if defined(CONFIG_DDR_ECC) +#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER) /* * Initialize and enable DDR ECC. */ diff --git a/board/mpc8540ads/mpc8540ads.c b/board/mpc8540ads/mpc8540ads.c index 01b03866e8..d0eb6904ad 100644 --- a/board/mpc8540ads/mpc8540ads.c +++ b/board/mpc8540ads/mpc8540ads.c @@ -31,7 +31,7 @@ #include #include -#if defined(CONFIG_DDR_ECC) +#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER) extern void ddr_enable_ecc(unsigned int dram_size); #endif @@ -96,7 +96,7 @@ initdram(int board_type) dram_size = fixed_sdram (); #endif -#if defined(CONFIG_DDR_ECC) +#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER) /* * Initialize and enable DDR ECC. */ diff --git a/board/mpc8560ads/mpc8560ads.c b/board/mpc8560ads/mpc8560ads.c index 1990e54769..9accc5cd33 100644 --- a/board/mpc8560ads/mpc8560ads.c +++ b/board/mpc8560ads/mpc8560ads.c @@ -33,7 +33,7 @@ #include #include -#if defined(CONFIG_DDR_ECC) +#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER) extern void ddr_enable_ecc(unsigned int dram_size); #endif @@ -293,7 +293,7 @@ initdram(int board_type) dram_size = fixed_sdram (); #endif -#if defined(CONFIG_DDR_ECC) +#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER) /* * Initialize and enable DDR ECC. */ diff --git a/cpu/mpc85xx/cpu.c b/cpu/mpc85xx/cpu.c index 4a1ccb05ba..f7fe22e3e1 100644 --- a/cpu/mpc85xx/cpu.c +++ b/cpu/mpc85xx/cpu.c @@ -38,6 +38,7 @@ int checkcpu (void) uint lcrr; /* local bus clock ratio register */ uint clkdiv; /* clock divider portion of lcrr */ uint pvr, svr; + uint fam; uint ver; uint major, minor; @@ -60,6 +61,12 @@ int checkcpu (void) case SVR_8560: puts("8560"); break; + case SVR_8548: + puts("8548"); + break; + case SVR_8548_E: + puts("8548_E"); + break; default: puts("Unknown"); break; @@ -67,13 +74,14 @@ int checkcpu (void) printf(", Version: %d.%d, (0x%08x)\n", major, minor, svr); pvr = get_pvr(); + fam = PVR_FAM(pvr); ver = PVR_VER(pvr); major = PVR_MAJ(pvr); minor = PVR_MIN(pvr); printf("Core: "); - switch (ver) { - case PVR_VER(PVR_85xx): + switch (fam) { + case PVR_FAM(PVR_85xx): puts("E500"); break; default: @@ -84,7 +92,7 @@ int checkcpu (void) get_sys_info(&sysinfo); - puts("Clocks Configuration:\n"); + puts("Clock Configuration:\n"); printf(" CPU:%4lu MHz, ", sysinfo.freqProcessor / 1000000); printf("CCB:%4lu MHz,\n", sysinfo.freqSystemBus / 1000000); printf(" DDR:%4lu MHz, ", sysinfo.freqSystemBus / 2000000); @@ -101,6 +109,13 @@ int checkcpu (void) #endif clkdiv = lcrr & 0x0f; if (clkdiv == 2 || clkdiv == 4 || clkdiv == 8) { +#ifdef CONFIG_MPC8548 + /* + * Yes, the entire PQ38 family use the same + * bit-representation for twice the clock divider values. + */ + clkdiv *= 2; +#endif printf("LBC:%4lu MHz\n", sysinfo.freqSystemBus / 1000000 / clkdiv); } else { diff --git a/cpu/mpc85xx/cpu_init.c b/cpu/mpc85xx/cpu_init.c index 79ea91f22a..efde9cc31a 100644 --- a/cpu/mpc85xx/cpu_init.c +++ b/cpu/mpc85xx/cpu_init.c @@ -178,42 +178,58 @@ void cpu_init_f (void) #endif } + /* - * We initialize L2 as cache here. + * Initialize L2 as cache. + * + * The newer 8548, etc, parts have twice as much cache, but + * use the same bit-encoding as the older 8555, etc, parts. + * + * FIXME: Use PVR_VER(pvr) == 1 test here instead of SVR_VER()? */ -int cpu_init_r (void) + +int cpu_init_r(void) { #if defined(CONFIG_L2_CACHE) - volatile immap_t *immap = (immap_t *)CFG_IMMR; + volatile immap_t *immap = (immap_t *)CFG_IMMR; volatile ccsr_l2cache_t *l2cache = &immap->im_l2cache; - volatile uint temp; + volatile uint cache_ctl; + uint svr, ver; + + svr = get_svr(); + ver = SVR_VER(svr); asm("msync;isync"); - temp = l2cache->l2ctl; - temp &= 0x30000000; - switch ( temp ) { + cache_ctl = l2cache->l2ctl; + + switch (cache_ctl & 0x30000000) { case 0x20000000: - printf ("L2 cache 256KB:"); + if (ver == SVR_8548 || ver == SVR_8548_E) { + printf ("L2 cache 512KB:"); + } else { + printf ("L2 cache 256KB:"); + } break; case 0x00000000: case 0x10000000: case 0x30000000: default: - printf ("L2 cache unknown size. Check the silicon!\n"); + printf ("L2 cache unknown size (0x%08x)\n", cache_ctl); return -1; } asm("msync;isync"); l2cache->l2ctl = 0x68000000; /* invalidate */ - temp = l2cache->l2ctl; + cache_ctl = l2cache->l2ctl; asm("msync;isync"); + l2cache->l2ctl = 0xa8000000; /* enable 256KB L2 cache */ - temp = l2cache->l2ctl; + cache_ctl = l2cache->l2ctl; asm("msync;isync"); - printf("enabled\n"); + printf(" enabled\n"); #else - printf("L2: disabled.\n"); + printf("L2 cache: disabled\n"); #endif return 0; diff --git a/cpu/mpc85xx/spd_sdram.c b/cpu/mpc85xx/spd_sdram.c index 5a1dbe2b53..049ba67e45 100644 --- a/cpu/mpc85xx/spd_sdram.c +++ b/cpu/mpc85xx/spd_sdram.c @@ -28,10 +28,11 @@ #include #include -#if defined(CONFIG_DDR_ECC) -extern void dma_init (void); + +#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER) +extern void dma_init(void); extern uint dma_check(void); -extern int dma_xfer (void *dest, uint count, void *src); +extern int dma_xfer(void *dest, uint count, void *src); #endif #ifdef CONFIG_SPD_EEPROM @@ -40,6 +41,9 @@ extern int dma_xfer (void *dest, uint count, void *src); #define CFG_READ_SPD i2c_read #endif +static unsigned int setup_laws_and_tlbs(unsigned int memsize); + + /* * Convert picoseconds into clock cycles (rounding up if needed). */ @@ -57,311 +61,829 @@ picos_to_clk(int picos) return clks; } + +/* + * Calculate the Density of each Physical Rank. + * Returned size is in bytes. + * + * Study these table from Byte 31 of JEDEC SPD Spec. + * + * DDR I DDR II + * Bit Size Size + * --- ----- ------ + * 7 high 512MB 512MB + * 6 256MB 256MB + * 5 128MB 128MB + * 4 64MB 16GB + * 3 32MB 8GB + * 2 16MB 4GB + * 1 2GB 2GB + * 0 low 1GB 1GB + * + * Reorder Table to be linear by stripping the bottom + * 2 or 5 bits off and shifting them up to the top. + */ + +unsigned int +compute_banksize(unsigned int mem_type, unsigned char row_dens) +{ + unsigned int bsize; + + if (mem_type == SPD_MEMTYPE_DDR) { + /* Bottom 2 bits up to the top. */ + bsize = ((row_dens >> 2) | ((row_dens & 3) << 6)) << 24; + debug("DDR: DDR I rank density = 0x%08x\n", bsize); + } else { + /* Bottom 5 bits up to the top. */ + bsize = ((row_dens >> 5) | ((row_dens & 31) << 3)) << 27; + debug("DDR: DDR II rank density = 0x%08x\n", bsize); + } + return bsize; +} + + +/* + * Convert a two-nibble BCD value into a cycle time. + * While the spec calls for nano-seconds, picos are returned. + * + * This implements the tables for bytes 9, 23 and 25 for both + * DDR I and II. No allowance for distinguishing the invalid + * fields absent for DDR I yet present in DDR II is made. + * (That is, cycle times of .25, .33, .66 and .75 ns are + * allowed for both DDR II and I.) + */ + unsigned int -banksize(unsigned char row_dens) +convert_bcd_tenths_to_cycle_time_ps(unsigned int spd_val) { - return ((row_dens >> 2) | ((row_dens & 3) << 6)) << 24; + /* + * Table look up the lower nibble, allow DDR I & II. + */ + unsigned int tenths_ps[16] = { + 0, + 100, + 200, + 300, + 400, + 500, + 600, + 700, + 800, + 900, + 250, + 330, /* FIXME: Is 333 better/valid? */ + 660, /* FIXME: Is 667 better/valid? */ + 750, + 0, /* undefined */ + 0 /* undefined */ + }; + + unsigned int whole_ns = (spd_val & 0xF0) >> 4; + unsigned int tenth_ns = spd_val & 0x0F; + unsigned int ps = whole_ns * 1000 + tenths_ps[tenth_ns]; + + return ps; } + long int spd_sdram(void) { volatile immap_t *immap = (immap_t *)CFG_IMMR; volatile ccsr_ddr_t *ddr = &immap->im_ddr; - volatile ccsr_local_ecm_t *ecm = &immap->im_local_ecm; + volatile ccsr_gur_t *gur = &immap->im_gur; spd_eeprom_t spd; - unsigned tmp, tmp1; + unsigned int n_ranks; + unsigned int rank_density; + unsigned int odt_rd_cfg, odt_wr_cfg; + unsigned int odt_cfg, mode_odt_enable; + unsigned int dqs_cfg; + unsigned char twr_clk, twtr_clk, twr_auto_clk; + unsigned int tCKmin_ps, tCKmax_ps; + unsigned int max_data_rate, effective_data_rate; + unsigned int busfreq; + unsigned sdram_cfg; unsigned int memsize; - unsigned int tlb_size; - unsigned int law_size; - unsigned char caslat; - unsigned int ram_tlb_index; - unsigned int ram_tlb_address; + unsigned char caslat, caslat_ctrl; + unsigned int trfc, trfc_clk, trfc_low, trfc_high; + unsigned int trcd_clk; + unsigned int trtp_clk; + unsigned char cke_min_clk; + unsigned char add_lat; + unsigned char wr_lat; + unsigned char wr_data_delay; + unsigned char four_act; + unsigned char cpo; + unsigned char burst_len; + unsigned int mode_caslat; + unsigned char sdram_type; + unsigned char d_init; - CFG_READ_SPD(SPD_EEPROM_ADDRESS, 0, 1, (uchar *) & spd, sizeof (spd)); + /* + * Read SPD information. + */ + CFG_READ_SPD(SPD_EEPROM_ADDRESS, 0, 1, (uchar *) &spd, sizeof(spd)); - if (spd.nrows > 2) { - puts("DDR:Only two chip selects are supported on ADS.\n"); + /* + * Check for supported memory module types. + */ + if (spd.mem_type != SPD_MEMTYPE_DDR && + spd.mem_type != SPD_MEMTYPE_DDR2) { + printf("Unable to locate DDR I or DDR II module.\n" + " Fundamental memory type is 0x%0x\n", + spd.mem_type); return 0; } - if (spd.nrow_addr < 12 - || spd.nrow_addr > 14 - || spd.ncol_addr < 8 - || spd.ncol_addr > 11) { - puts("DDR:Row or Col number unsupported.\n"); + /* + * These test gloss over DDR I and II differences in interpretation + * of bytes 3 and 4, but irrelevantly. Multiple asymmetric banks + * are not supported on DDR I; and not encoded on DDR II. + * + * Also note that the 8548 controller can support: + * 12 <= nrow <= 16 + * and + * 8 <= ncol <= 11 (still, for DDR) + * 6 <= ncol <= 9 (for FCRAM) + */ + if (spd.nrow_addr < 12 || spd.nrow_addr > 14) { + printf("DDR: Unsupported number of Row Addr lines: %d.\n", + spd.nrow_addr); + return 0; + } + if (spd.ncol_addr < 8 || spd.ncol_addr > 11) { + printf("DDR: Unsupported number of Column Addr lines: %d.\n", + spd.ncol_addr); return 0; } - ddr->cs0_bnds = (banksize(spd.row_dens) >> 24) - 1; - ddr->cs0_config = ( 1 << 31 - | (spd.nrow_addr - 12) << 8 - | (spd.ncol_addr - 8) ); - debug("\n"); - debug("cs0_bnds = 0x%08x\n",ddr->cs0_bnds); - debug("cs0_config = 0x%08x\n",ddr->cs0_config); - - if (spd.nrows == 2) { - ddr->cs1_bnds = ( (banksize(spd.row_dens) >> 8) - | ((banksize(spd.row_dens) >> 23) - 1) ); - ddr->cs1_config = ( 1<<31 - | (spd.nrow_addr-12) << 8 - | (spd.ncol_addr-8) ); - debug("cs1_bnds = 0x%08x\n",ddr->cs1_bnds); - debug("cs1_config = 0x%08x\n",ddr->cs1_config); + /* + * Determine the number of physical banks controlled by + * different Chip Select signals. This is not quite the + * same as the number of DIMM modules on the board. Feh. + */ + if (spd.mem_type == SPD_MEMTYPE_DDR) { + n_ranks = spd.nrows; + } else { + n_ranks = (spd.nrows & 0x7) + 1; } - if (spd.mem_type != 0x07) { - puts("No DDR module found!\n"); + debug("DDR: number of ranks = %d\n", n_ranks); + + if (n_ranks > 2) { + printf("DDR: Only 2 chip selects are supported: %d\n", + n_ranks); return 0; } /* - * Figure out memory size in Megabytes. + * Adjust DDR II IO voltage biasing. It just makes it work. */ - memsize = spd.nrows * banksize(spd.row_dens) / 0x100000; + if (spd.mem_type == SPD_MEMTYPE_DDR2) { + gur->ddrioovcr = (0 + | 0x80000000 /* Enable */ + | 0x10000000 /* VSEL to 1.8V */ + ); + } /* - * First supported LAW size is 16M, at LAWAR_SIZE_16M == 23. Fnord. + * Determine the size of each Rank in bytes. */ - law_size = 19 + __ilog2(memsize); + rank_density = compute_banksize(spd.mem_type, spd.row_dens); + /* - * Determine size of each TLB1 entry. + * Eg: Bounds: 0x0000_0000 to 0x0f000_0000 first 256 Meg */ - switch (memsize) { - case 16: - case 32: - tlb_size = BOOKE_PAGESZ_16M; - break; - case 64: - case 128: - tlb_size = BOOKE_PAGESZ_64M; - break; - case 256: - case 512: - case 1024: - case 2048: - tlb_size = BOOKE_PAGESZ_256M; - break; - default: - puts("DDR: only 16M,32M,64M,128M,256M,512M,1G and 2G DDR I are supported.\n"); - return 0; - break; - } + ddr->cs0_bnds = (rank_density >> 24) - 1; /* - * Configure DDR TLB1 entries. - * Starting at TLB1 8, use no more than 8 TLB1 entries. + * ODT configuration recommendation from DDR Controller Chapter. */ - ram_tlb_index = 8; - ram_tlb_address = (unsigned int)CFG_DDR_SDRAM_BASE; - while (ram_tlb_address < (memsize * 1024 * 1024) - && ram_tlb_index < 16) { - mtspr(MAS0, TLB1_MAS0(1, ram_tlb_index, 0)); - mtspr(MAS1, TLB1_MAS1(1, 1, 0, 0, tlb_size)); - mtspr(MAS2, TLB1_MAS2(E500_TLB_EPN(ram_tlb_address), - 0, 0, 0, 0, 0, 0, 0, 0)); - mtspr(MAS3, TLB1_MAS3(E500_TLB_RPN(ram_tlb_address), - 0, 0, 0, 0, 0, 1, 0, 1, 0, 1)); - asm volatile("isync;msync;tlbwe;isync"); + odt_rd_cfg = 0; /* Never assert ODT */ + odt_wr_cfg = 0; /* Never assert ODT */ + if (spd.mem_type == SPD_MEMTYPE_DDR2) { + odt_wr_cfg = 1; /* Assert ODT on writes to CS0 */ +#if 0 + /* FIXME: How to determine the number of dimm modules? */ + if (n_dimm_modules == 2) { + odt_rd_cfg = 1; /* Assert ODT on reads to CS0 */ + } +#endif + } - debug("DDR:MAS0=0x%08x\n", TLB1_MAS0(1, ram_tlb_index, 0)); - debug("DDR:MAS1=0x%08x\n", TLB1_MAS1(1, 1, 0, 0, tlb_size)); - debug("DDR:MAS2=0x%08x\n", - TLB1_MAS2(E500_TLB_EPN(ram_tlb_address), - 0, 0, 0, 0, 0, 0, 0, 0)); - debug("DDR:MAS3=0x%08x\n", - TLB1_MAS3(E500_TLB_RPN(ram_tlb_address), - 0, 0, 0, 0, 0, 1, 0, 1, 0, 1)); + ddr->cs0_config = ( 1 << 31 + | (odt_rd_cfg << 20) + | (odt_wr_cfg << 16) + | (spd.nrow_addr - 12) << 8 + | (spd.ncol_addr - 8) ); + debug("\n"); + debug("DDR: cs0_bnds = 0x%08x\n", ddr->cs0_bnds); + debug("DDR: cs0_config = 0x%08x\n", ddr->cs0_config); - ram_tlb_address += (0x1000 << ((tlb_size - 1) * 2)); - ram_tlb_index++; + if (n_ranks == 2) { + /* + * Eg: Bounds: 0x0f00_0000 to 0x1e0000_0000, second 256 Meg + */ + ddr->cs1_bnds = ( (rank_density >> 8) + | ((rank_density >> (24 - 1)) - 1) ); + ddr->cs1_config = ( 1<<31 + | (odt_rd_cfg << 20) + | (odt_wr_cfg << 16) + | (spd.nrow_addr - 12) << 8 + | (spd.ncol_addr - 8) ); + debug("DDR: cs1_bnds = 0x%08x\n", ddr->cs1_bnds); + debug("DDR: cs1_config = 0x%08x\n", ddr->cs1_config); } + /* - * Set up LAWBAR for all of DDR. + * Find the largest CAS by locating the highest 1 bit + * in the spd.cas_lat field. Translate it to a DDR + * controller field value: + * + * CAS Lat DDR I DDR II Ctrl + * Clocks SPD Bit SPD Bit Value + * ------- ------- ------- ----- + * 1.0 0 0001 + * 1.5 1 0010 + * 2.0 2 2 0011 + * 2.5 3 0100 + * 3.0 4 3 0101 + * 3.5 5 0110 + * 4.0 4 0111 + * 4.5 1000 + * 5.0 5 1001 */ - ecm->lawbar1 = ((CFG_DDR_SDRAM_BASE>>12) & 0xfffff); - ecm->lawar1 = (LAWAR_EN | LAWAR_TRGT_IF_DDR | (LAWAR_SIZE & law_size)); - debug("DDR:LAWBAR1=0x%08x\n", ecm->lawbar1); - debug("DDR:LARAR1=0x%08x\n", ecm->lawar1); - - /* - * find the largest CAS - */ - if(spd.cas_lat & 0x40) { - caslat = 7; - } else if (spd.cas_lat & 0x20) { - caslat = 6; - } else if (spd.cas_lat & 0x10) { - caslat = 5; - } else if (spd.cas_lat & 0x08) { - caslat = 4; - } else if (spd.cas_lat & 0x04) { - caslat = 3; - } else if (spd.cas_lat & 0x02) { - caslat = 2; - } else if (spd.cas_lat & 0x01) { - caslat = 1; - } else { - puts("DDR:no valid CAS Latency information.\n"); + caslat = __ilog2(spd.cas_lat); + if ((spd.mem_type == SPD_MEMTYPE_DDR) + && (caslat > 5)) { + printf("DDR I: Invalid SPD CAS Latency: 0x%x.\n", spd.cas_lat); + return 0; + + } else if (spd.mem_type == SPD_MEMTYPE_DDR2 + && (caslat < 2 || caslat > 5)) { + printf("DDR II: Invalid SPD CAS Latency: 0x%x.\n", + spd.cas_lat); return 0; } + debug("DDR: caslat SPD bit is %d\n", caslat); + + /* + * Calculate the Maximum Data Rate based on the Minimum Cycle time. + * The SPD clk_cycle field (tCKmin) is measured in tenths of + * nanoseconds and represented as BCD. + */ + tCKmin_ps = convert_bcd_tenths_to_cycle_time_ps(spd.clk_cycle); + debug("DDR: tCKmin = %d ps\n", tCKmin_ps); + + /* + * Double-data rate, scaled 1000 to picoseconds, and back down to MHz. + */ + max_data_rate = 2 * 1000 * 1000 / tCKmin_ps; + debug("DDR: Module max data rate = %d Mhz\n", max_data_rate); + - tmp = 20000 / (((spd.clk_cycle & 0xF0) >> 4) * 10 - + (spd.clk_cycle & 0x0f)); - debug("DDR:Module maximum data rate is: %dMhz\n", tmp); + /* + * Adjust the CAS Latency to allow for bus speeds that + * are slower than the DDR module. + */ + busfreq = get_bus_freq(0) / 1000000; /* MHz */ - tmp1 = get_bus_freq(0) / 1000000; - if (tmp1 < 230 && tmp1 >= 90 && tmp >= 230) { - /* 90~230 range, treated as DDR 200 */ - if (spd.clk_cycle3 == 0xa0) + effective_data_rate = max_data_rate; + if (busfreq < 90) { + /* DDR rate out-of-range */ + puts("DDR: platform frequency is not fit for DDR rate\n"); + return 0; + + } else if (90 <= busfreq && busfreq < 230 && max_data_rate >= 230) { + /* + * busfreq 90~230 range, treated as DDR 200. + */ + effective_data_rate = 200; + if (spd.clk_cycle3 == 0xa0) /* 10 ns */ caslat -= 2; - else if(spd.clk_cycle2 == 0xa0) + else if (spd.clk_cycle2 == 0xa0) caslat--; - } else if (tmp1 < 280 && tmp1 >= 230 && tmp >= 280) { - /* 230-280 range, treated as DDR 266 */ - if (spd.clk_cycle3 == 0x75) + + } else if (230 <= busfreq && busfreq < 280 && max_data_rate >= 280) { + /* + * busfreq 230~280 range, treated as DDR 266. + */ + effective_data_rate = 266; + if (spd.clk_cycle3 == 0x75) /* 7.5 ns */ caslat -= 2; else if (spd.clk_cycle2 == 0x75) caslat--; - } else if (tmp1 < 350 && tmp1 >= 280 && tmp >= 350) { - /* 280~350 range, treated as DDR 333 */ - if (spd.clk_cycle3 == 0x60) + + } else if (280 <= busfreq && busfreq < 350 && max_data_rate >= 350) { + /* + * busfreq 280~350 range, treated as DDR 333. + */ + effective_data_rate = 333; + if (spd.clk_cycle3 == 0x60) /* 6.0 ns */ caslat -= 2; else if (spd.clk_cycle2 == 0x60) caslat--; - } else if (tmp1 < 90 || tmp1 >= 350) { - /* DDR rate out-of-range */ - puts("DDR:platform frequency is not fit for DDR rate\n"); + + } else if (350 <= busfreq && busfreq < 460 && max_data_rate >= 460) { + /* + * busfreq 350~460 range, treated as DDR 400. + */ + effective_data_rate = 400; + if (spd.clk_cycle3 == 0x50) /* 5.0 ns */ + caslat -= 2; + else if (spd.clk_cycle2 == 0x50) + caslat--; + + } else if (460 <= busfreq && busfreq < 560 && max_data_rate >= 560) { + /* + * busfreq 460~560 range, treated as DDR 533. + */ + effective_data_rate = 533; + if (spd.clk_cycle3 == 0x3D) /* 3.75 ns */ + caslat -= 2; + else if (spd.clk_cycle2 == 0x3D) + caslat--; + + } else if (560 <= busfreq && busfreq < 700 && max_data_rate >= 700) { + /* + * busfreq 560~700 range, treated as DDR 667. + */ + effective_data_rate = 667; + if (spd.clk_cycle3 == 0x30) /* 3.0 ns */ + caslat -= 2; + else if (spd.clk_cycle2 == 0x30) + caslat--; + + } else if (700 <= busfreq) { + /* + * DDR rate out-of-range + */ + printf("DDR: Bus freq %d MHz is not fit for DDR rate %d MHz\n", + busfreq, max_data_rate); return 0; } + /* - * note: caslat must also be programmed into ddr->sdram_mode - * register. - * - * note: WRREC(Twr) and WRTORD(Twtr) are not in SPD, - * use conservative value here. + * Convert caslat clocks to DDR controller value. + * Force caslat_ctrl to be DDR Controller field-sized. + */ + if (spd.mem_type == SPD_MEMTYPE_DDR) { + caslat_ctrl = (caslat + 1) & 0x07; + } else { + caslat_ctrl = (2 * caslat - 1) & 0x0f; + } + + debug("DDR: effective data rate is %d MHz\n", effective_data_rate); + debug("DDR: caslat SPD bit is %d, controller field is 0x%x\n", + caslat, caslat_ctrl); + + /* + * Timing Config 0. + * Avoid writing for DDR I. The new PQ38 DDR controller + * dreams up non-zero default values to be backwards compatible. */ + if (spd.mem_type == SPD_MEMTYPE_DDR2) { + unsigned char taxpd_clk = 8; /* By the book. */ + unsigned char tmrd_clk = 2; /* By the book. */ + unsigned char act_pd_exit = 2; /* Empirical? */ + unsigned char pre_pd_exit = 6; /* Empirical? */ + + ddr->timing_cfg_0 = (0 + | ((act_pd_exit & 0x7) << 20) /* ACT_PD_EXIT */ + | ((pre_pd_exit & 0x7) << 16) /* PRE_PD_EXIT */ + | ((taxpd_clk & 0xf) << 8) /* ODT_PD_EXIT */ + | ((tmrd_clk & 0xf) << 0) /* MRS_CYC */ + ); +#if 0 + ddr->timing_cfg_0 |= 0xaa000000; /* extra cycles */ +#endif + debug("DDR: timing_cfg_0 = 0x%08x\n", ddr->timing_cfg_0); + + } else { +#if 0 + /* + * Force extra cycles with 0xaa bits. + * Incidentally supply the dreamt-up backwards compat value! + */ + ddr->timing_cfg_0 = 0x00110105; /* backwards compat value */ + ddr->timing_cfg_0 |= 0xaa000000; /* extra cycles */ + debug("DDR: HACK timing_cfg_0 = 0x%08x\n", ddr->timing_cfg_0); +#endif + } + + + /* + * Some Timing Config 1 values now. + * Sneak Extended Refresh Recovery in here too. + */ + + /* + * For DDR I, WRREC(Twr) and WRTORD(Twtr) are not in SPD, + * use conservative value. + * For DDR II, they are bytes 36 and 37, in quarter nanos. + */ + + if (spd.mem_type == SPD_MEMTYPE_DDR) { + twr_clk = 3; /* Clocks */ + twtr_clk = 1; /* Clocks */ + } else { + twr_clk = picos_to_clk(spd.twr * 250); + twtr_clk = picos_to_clk(spd.twtr * 250); + } + + /* + * Calculate Trfc, in picos. + * DDR I: Byte 42 straight up in ns. + * DDR II: Byte 40 and 42 swizzled some, in ns. + */ + if (spd.mem_type == SPD_MEMTYPE_DDR) { + trfc = spd.trfc * 1000; /* up to ps */ + } else { + unsigned int byte40_table_ps[8] = { + 0, + 250, + 330, + 500, + 660, + 750, + 0, + 0 + }; + + trfc = (((spd.trctrfc_ext & 0x1) * 256) + spd.trfc) * 1000 + + byte40_table_ps[(spd.trctrfc_ext >> 1) & 0x7]; + } + trfc_clk = picos_to_clk(trfc); + + /* + * Trcd, Byte 29, from quarter nanos to ps and clocks. + */ + trcd_clk = picos_to_clk(spd.trcd * 250) & 0x7; + + /* + * Convert trfc_clk to DDR controller fields. DDR I should + * fit in the REFREC field (16-19) of TIMING_CFG_1, but the + * 8548 controller has an extended REFREC field of three bits. + * The controller automatically adds 8 clocks to this value, + * so preadjust it down 8 first before splitting it up. + */ + trfc_low = (trfc_clk - 8) & 0xf; + trfc_high = ((trfc_clk - 8) >> 4) & 0x3; + + /* + * Sneak in some Extended Refresh Recovery. + */ + ddr->ext_refrec = (trfc_high << 16); + debug("DDR: ext_refrec = 0x%08x\n", ddr->ext_refrec); + ddr->timing_cfg_1 = - (((picos_to_clk(spd.trp * 250) & 0x07) << 28 ) | - ((picos_to_clk(spd.tras * 1000) & 0x0f ) << 24 ) | - ((picos_to_clk(spd.trcd * 250) & 0x07) << 20 ) | - ((caslat & 0x07) << 16 ) | - (((picos_to_clk(spd.sset[6] * 1000) - 8) & 0x0f) << 12 ) | - ( 0x300 ) | - ((picos_to_clk(spd.trrd * 250) & 0x07) << 4) | 1); + (0 + | ((picos_to_clk(spd.trp * 250) & 0x07) << 28) /* PRETOACT */ + | ((picos_to_clk(spd.tras * 1000) & 0x0f ) << 24) /* ACTTOPRE */ + | (trcd_clk << 20) /* ACTTORW */ + | (caslat_ctrl << 16) /* CASLAT */ + | (trfc_low << 12) /* REFEC */ + | ((twr_clk & 0x07) << 8) /* WRRREC */ + | ((picos_to_clk(spd.trrd * 250) & 0x07) << 4) /* ACTTOACT */ + | ((twtr_clk & 0x07) << 0) /* WRTORD */ + ); - ddr->timing_cfg_2 = 0x00000800; + debug("DDR: timing_cfg_1 = 0x%08x\n", ddr->timing_cfg_1); - debug("DDR:timing_cfg_1=0x%08x\n", ddr->timing_cfg_1); - debug("DDR:timing_cfg_2=0x%08x\n", ddr->timing_cfg_2); /* - * Only DDR I is supported - * DDR I and II have different mode-register-set definition + * Timing_Config_2 + * Was: 0x00000800; */ - /* burst length is always 4 */ - switch(caslat) { - case 2: - ddr->sdram_mode = 0x52; /* 1.5 */ - break; - case 3: - ddr->sdram_mode = 0x22; /* 2.0 */ - break; - case 4: - ddr->sdram_mode = 0x62; /* 2.5 */ - break; - case 5: - ddr->sdram_mode = 0x32; /* 3.0 */ - break; - default: - puts("DDR:only CAS Latency 1.5, 2.0, 2.5, 3.0 is supported.\n"); - return 0; + /* + * Additive Latency + * For DDR I, 0. + * For DDR II, with ODT enabled, use "a value" less than ACTTORW, + * which comes from Trcd, and also note that: + * add_lat + caslat must be >= 4 + */ + add_lat = 0; + if (spd.mem_type == SPD_MEMTYPE_DDR2 + && (odt_wr_cfg || odt_rd_cfg) + && (caslat < 4)) { + add_lat = 4 - caslat; + if (add_lat > trcd_clk) { + add_lat = trcd_clk - 1; + } } - debug("DDR:sdram_mode=0x%08x\n", ddr->sdram_mode); - switch(spd.refresh) { - case 0x00: - case 0x80: - tmp = picos_to_clk(15625000); - break; - case 0x01: - case 0x81: - tmp = picos_to_clk(3900000); - break; - case 0x02: - case 0x82: - tmp = picos_to_clk(7800000); - break; - case 0x03: - case 0x83: - tmp = picos_to_clk(31300000); - break; - case 0x04: - case 0x84: - tmp = picos_to_clk(62500000); - break; - case 0x05: - case 0x85: - tmp = picos_to_clk(125000000); - break; - default: - tmp = 0x512; - break; + /* + * Write Data Delay + * Historically 0x2 == 4/8 clock delay. + * Empirically, 0x3 == 6/8 clock delay is suggested for DDR I 266. + */ + wr_data_delay = 3; + + /* + * Write Latency + * Read to Precharge + * Minimum CKE Pulse Width. + * Four Activate Window + */ + if (spd.mem_type == SPD_MEMTYPE_DDR) { + /* + * This is a lie. It should really be 1, but if it is + * set to 1, bits overlap into the old controller's + * otherwise unused ACSM field. If we leave it 0, then + * the HW will magically treat it as 1 for DDR 1. Oh Yea. + */ + wr_lat = 0; + + trtp_clk = 2; /* By the book. */ + cke_min_clk = 1; /* By the book. */ + four_act = 1; /* By the book. */ + + } else { + wr_lat = caslat - 1; + + /* Convert SPD value from quarter nanos to picos. */ + trtp_clk = picos_to_clk(spd.trtp * 250); + + cke_min_clk = 3; /* By the book. */ + four_act = picos_to_clk(37500); /* By the book. 1k pages? */ + } + + /* + * Empirically set ~MCAS-to-preamble override for DDR 2. + * Your milage will vary. + */ + cpo = 0; + if (spd.mem_type == SPD_MEMTYPE_DDR2) { + if (effective_data_rate == 266 || effective_data_rate == 333) { + cpo = 0x7; /* READ_LAT + 5/4 */ + } else if (effective_data_rate == 400) { + cpo = 0x9; /* READ_LAT + 7/4 */ + } else { + /* Pure speculation */ + cpo = 0xb; + } + } + + ddr->timing_cfg_2 = (0 + | ((add_lat & 0x7) << 28) /* ADD_LAT */ + | ((cpo & 0x1f) << 23) /* CPO */ + | ((wr_lat & 0x7) << 19) /* WR_LAT */ + | ((trtp_clk & 0x7) << 13) /* RD_TO_PRE */ + | ((wr_data_delay & 0x7) << 10) /* WR_DATA_DELAY */ + | ((cke_min_clk & 0x7) << 6) /* CKE_PLS */ + | ((four_act & 0x1f) << 0) /* FOUR_ACT */ + ); + + debug("DDR: timing_cfg_2 = 0x%08x\n", ddr->timing_cfg_2); + + + /* + * Determine the Mode Register Set. + * + * This is nominally part specific, but it appears to be + * consistent for all DDR I devices, and for all DDR II devices. + * + * caslat must be programmed + * burst length is always 4 + * burst type is sequential + * + * For DDR I: + * operating mode is "normal" + * + * For DDR II: + * other stuff + */ + + mode_caslat = 0; + + /* + * Table lookup from DDR I or II Device Operation Specs. + */ + if (spd.mem_type == SPD_MEMTYPE_DDR) { + if (1 <= caslat && caslat <= 4) { + unsigned char mode_caslat_table[4] = { + 0x5, /* 1.5 clocks */ + 0x2, /* 2.0 clocks */ + 0x6, /* 2.5 clocks */ + 0x3 /* 3.0 clocks */ + }; + mode_caslat = mode_caslat_table[caslat - 1]; + } else { + puts("DDR I: Only CAS Latencies of 1.5, 2.0, " + "2.5 and 3.0 clocks are supported.\n"); + return 0; + } + + } else { + if (2 <= caslat && caslat <= 5) { + mode_caslat = caslat; + } else { + puts("DDR II: Only CAS Latencies of 2.0, 3.0, " + "4.0 and 5.0 clocks are supported.\n"); + return 0; + } + } + + /* + * Encoded Burst Lenght of 4. + */ + burst_len = 2; /* Fiat. */ + + if (spd.mem_type == SPD_MEMTYPE_DDR) { + twr_auto_clk = 0; /* Historical */ + } else { + /* + * Determine tCK max in picos. Grab tWR and convert to picos. + * Auto-precharge write recovery is: + * WR = roundup(tWR_ns/tCKmax_ns). + * + * Ponder: Is twr_auto_clk different than twr_clk? + */ + tCKmax_ps = convert_bcd_tenths_to_cycle_time_ps(spd.tckmax); + twr_auto_clk = (spd.twr * 250 + tCKmax_ps - 1) / tCKmax_ps; + } + + + /* + * Mode Reg in bits 16 ~ 31, + * Extended Mode Reg 1 in bits 0 ~ 15. + */ + mode_odt_enable = 0x0; /* Default disabled */ + if (odt_wr_cfg || odt_rd_cfg) { + /* + * Bits 6 and 2 in Extended MRS(1) + * Bit 2 == 0x04 == 75 Ohm, with 2 DIMM modules. + * Bit 6 == 0x40 == 150 Ohm, with 1 DIMM module. + */ + mode_odt_enable = 0x40; /* 150 Ohm */ } + ddr->sdram_mode = + (0 + | (add_lat << (16 + 3)) /* Additive Latency in EMRS1 */ + | (mode_odt_enable << 16) /* ODT Enable in EMRS1 */ + | (twr_auto_clk << 9) /* Write Recovery Autopre */ + | (mode_caslat << 4) /* caslat */ + | (burst_len << 0) /* Burst length */ + ); + + debug("DDR: sdram_mode = 0x%08x\n", ddr->sdram_mode); + + + /* + * Clear EMRS2 and EMRS3. + */ + ddr->sdram_mode_2 = 0; + debug("DDR: sdram_mode_2 = 0x%08x\n", ddr->sdram_mode_2); + + /* - * Set BSTOPRE to 0x100 for page mode - * If auto-charge is used, set BSTOPRE = 0 + * Determine Refresh Rate. Ignore self refresh bit on DDR I. + * Table from SPD Spec, Byte 12, converted to picoseconds and + * filled in with "default" normal values. */ - ddr->sdram_interval = ((tmp & 0x3fff) << 16) | 0x100; - debug("DDR:sdram_interval=0x%08x\n", ddr->sdram_interval); + { + unsigned int refresh_clk; + unsigned int refresh_time_ns[8] = { + 15625000, /* 0 Normal 1.00x */ + 3900000, /* 1 Reduced .25x */ + 7800000, /* 2 Extended .50x */ + 31300000, /* 3 Extended 2.00x */ + 62500000, /* 4 Extended 4.00x */ + 125000000, /* 5 Extended 8.00x */ + 15625000, /* 6 Normal 1.00x filler */ + 15625000, /* 7 Normal 1.00x filler */ + }; + + refresh_clk = picos_to_clk(refresh_time_ns[spd.refresh & 0x7]); + + /* + * Set BSTOPRE to 0x100 for page mode + * If auto-charge is used, set BSTOPRE = 0 + */ + ddr->sdram_interval = + (0 + | (refresh_clk & 0x3fff) << 16 + | 0x100 + ); + debug("DDR: sdram_interval = 0x%08x\n", ddr->sdram_interval); + } /* * Is this an ECC DDR chip? + * But don't mess with it if the DDR controller will init mem. */ -#if defined(CONFIG_DDR_ECC) +#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER) if (spd.config == 0x02) { ddr->err_disable = 0x0000000d; ddr->err_sbe = 0x00ff0000; } - debug("DDR:err_disable=0x%08x\n", ddr->err_disable); - debug("DDR:err_sbe=0x%08x\n", ddr->err_sbe); + debug("DDR: err_disable = 0x%08x\n", ddr->err_disable); + debug("DDR: err_sbe = 0x%08x\n", ddr->err_sbe); #endif - asm("sync;isync;msync"); + asm("sync;isync;msync"); udelay(500); -#ifdef MPC85xx_DDR_SDRAM_CLK_CNTL - /* Setup the clock control (8555 and later) - * SDRAM_CLK_CNTL[0] = Source synchronous enable == 1 - * SDRAM_CLK_CNTL[5-7] = Clock Adjust == 3 (3/4 cycle late) + /* + * SDRAM Cfg 2 + */ + + /* + * When ODT is enabled, Chap 9 suggests asserting ODT to + * internal IOs only during reads. + */ + odt_cfg = 0; + if (odt_rd_cfg | odt_wr_cfg) { + odt_cfg = 0x2; /* ODT to IOs during reads */ + } + + /* + * Try to use differential DQS with DDR II. */ - ddr->sdram_clk_cntl = 0x83000000; + if (spd.mem_type == SPD_MEMTYPE_DDR) { + dqs_cfg = 0; /* No Differential DQS for DDR I */ + } else { + dqs_cfg = 0x1; /* Differential DQS for DDR II */ + } + +#if defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER) + /* + * Use the DDR controller to auto initialize memory. + */ + d_init = 1; + ddr->sdram_data_init = CONFIG_MEM_INIT_VALUE; + debug("DDR: ddr_data_init = 0x%08x\n", ddr->sdram_data_init); +#else + /* + * Memory will be initialized via DMA, or not at all. + */ + d_init = 0; +#endif + + ddr->sdram_cfg_2 = (0 + | (dqs_cfg << 26) /* Differential DQS */ + | (odt_cfg << 21) /* ODT */ + | (d_init << 4) /* D_INIT auto init DDR */ + ); + + debug("DDR: sdram_cfg_2 = 0x%08x\n", ddr->sdram_cfg_2); + + +#ifdef MPC85xx_DDR_SDRAM_CLK_CNTL + { + unsigned char clk_adjust; + + /* + * Setup the clock control. + * SDRAM_CLK_CNTL[0] = Source synchronous enable == 1 + * SDRAM_CLK_CNTL[5-7] = Clock Adjust + * 0110 3/4 cycle late + * 0111 7/8 cycle late + */ + if (spd.mem_type == SPD_MEMTYPE_DDR) { + clk_adjust = 0x6; + } else { + clk_adjust = 0x7; + } + + ddr->sdram_clk_cntl = (0 + | 0x80000000 + | (clk_adjust << 23) + ); + debug("DDR: sdram_clk_cntl = 0x%08x\n", ddr->sdram_clk_cntl); + } #endif /* - * Figure out the settings for the sdram_cfg register. Build up - * the entire register in 'tmp' before writing since the write into - * the register will actually enable the memory controller, and all - * settings must be done before enabling. + * Figure out the settings for the sdram_cfg register. + * Build up the entire register in 'sdram_cfg' before writing + * since the write into the register will actually enable the + * memory controller; all settings must be done before enabling. * * sdram_cfg[0] = 1 (ddr sdram logic enable) * sdram_cfg[1] = 1 (self-refresh-enable) - * sdram_cfg[6:7] = 2 (SDRAM type = DDR SDRAM) + * sdram_cfg[5:7] = (SDRAM type = DDR SDRAM) + * 010 DDR 1 SDRAM + * 011 DDR 2 SDRAM */ - tmp = 0xc2000000; + sdram_type = (spd.mem_type == SPD_MEMTYPE_DDR) ? 2 : 3; + sdram_cfg = (0 + | (1 << 31) /* Enable */ + | (1 << 30) /* Self refresh */ + | (sdram_type << 24) /* SDRAM type */ + ); /* * sdram_cfg[3] = RD_EN - registered DIMM enable * A value of 0x26 indicates micron registered DIMMS (micron.com) */ - if (spd.mod_attr == 0x26) { - tmp |= 0x10000000; + if (spd.mem_type == SPD_MEMTYPE_DDR && spd.mod_attr == 0x26) { + sdram_cfg |= 0x10000000; /* RD_EN */ } #if defined(CONFIG_DDR_ECC) @@ -369,7 +891,7 @@ spd_sdram(void) * If the user wanted ECC (enabled via sdram_cfg[2]) */ if (spd.config == 0x02) { - tmp |= 0x20000000; + sdram_cfg |= 0x20000000; /* ECC_EN */ } #endif @@ -385,27 +907,160 @@ spd_sdram(void) /* * Enable 2T timing by setting sdram_cfg[16]. */ - tmp |= 0x8000; + sdram_cfg |= 0x8000; /* 2T_EN */ #endif } } - ddr->sdram_cfg = tmp; + /* + * 200 painful micro-seconds must elapse between + * the DDR clock setup and the DDR config enable. + */ + udelay(200); + + /* + * Go! + */ + ddr->sdram_cfg = sdram_cfg; asm("sync;isync;msync"); udelay(500); - debug("DDR:sdram_cfg=0x%08x\n", ddr->sdram_cfg); + debug("DDR: sdram_cfg = 0x%08x\n", ddr->sdram_cfg); + + +#if defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER) + /* + * Poll until memory is initialized. + * 512 Meg at 400 might hit this 200 times or so. + */ + while ((ddr->sdram_cfg_2 & (d_init << 4)) != 0) { + udelay(1000); + } +#endif + + + /* + * Figure out memory size in Megabytes. + */ + memsize = n_ranks * rank_density / 0x100000; + + /* + * Establish Local Access Window and TLB mappings for DDR memory. + */ + memsize = setup_laws_and_tlbs(memsize); + if (memsize == 0) { + return 0; + } return memsize * 1024 * 1024; } + + +/* + * Setup Local Access Window and TLB1 mappings for the requested + * amount of memory. Returns the amount of memory actually mapped + * (usually the original request size), or 0 on error. + */ + +static unsigned int +setup_laws_and_tlbs(unsigned int memsize) +{ + volatile immap_t *immap = (immap_t *)CFG_IMMR; + volatile ccsr_local_ecm_t *ecm = &immap->im_local_ecm; + unsigned int tlb_size; + unsigned int law_size; + unsigned int ram_tlb_index; + unsigned int ram_tlb_address; + + /* + * Determine size of each TLB1 entry. + */ + switch (memsize) { + case 16: + case 32: + tlb_size = BOOKE_PAGESZ_16M; + break; + case 64: + case 128: + tlb_size = BOOKE_PAGESZ_64M; + break; + case 256: + case 512: + case 1024: + case 2048: + tlb_size = BOOKE_PAGESZ_256M; + break; + default: + puts("DDR: only 16M,32M,64M,128M,256M,512M,1G and 2G are supported.\n"); + + /* + * The memory was not able to be mapped. + */ + return 0; + break; + } + + /* + * Configure DDR TLB1 entries. + * Starting at TLB1 8, use no more than 8 TLB1 entries. + */ + ram_tlb_index = 8; + ram_tlb_address = (unsigned int)CFG_DDR_SDRAM_BASE; + while (ram_tlb_address < (memsize * 1024 * 1024) + && ram_tlb_index < 16) { + mtspr(MAS0, TLB1_MAS0(1, ram_tlb_index, 0)); + mtspr(MAS1, TLB1_MAS1(1, 1, 0, 0, tlb_size)); + mtspr(MAS2, TLB1_MAS2(E500_TLB_EPN(ram_tlb_address), + 0, 0, 0, 0, 0, 0, 0, 0)); + mtspr(MAS3, TLB1_MAS3(E500_TLB_RPN(ram_tlb_address), + 0, 0, 0, 0, 0, 1, 0, 1, 0, 1)); + asm volatile("isync;msync;tlbwe;isync"); + + debug("DDR: MAS0=0x%08x\n", TLB1_MAS0(1, ram_tlb_index, 0)); + debug("DDR: MAS1=0x%08x\n", TLB1_MAS1(1, 1, 0, 0, tlb_size)); + debug("DDR: MAS2=0x%08x\n", + TLB1_MAS2(E500_TLB_EPN(ram_tlb_address), + 0, 0, 0, 0, 0, 0, 0, 0)); + debug("DDR: MAS3=0x%08x\n", + TLB1_MAS3(E500_TLB_RPN(ram_tlb_address), + 0, 0, 0, 0, 0, 1, 0, 1, 0, 1)); + + ram_tlb_address += (0x1000 << ((tlb_size - 1) * 2)); + ram_tlb_index++; + } + + + /* + * First supported LAW size is 16M, at LAWAR_SIZE_16M == 23. Fnord. + */ + law_size = 19 + __ilog2(memsize); + + /* + * Set up LAWBAR for all of DDR. + */ + ecm->lawbar1 = ((CFG_DDR_SDRAM_BASE >> 12) & 0xfffff); + ecm->lawar1 = (LAWAR_EN + | LAWAR_TRGT_IF_DDR + | (LAWAR_SIZE & law_size)); + debug("DDR: LAWBAR1=0x%08x\n", ecm->lawbar1); + debug("DDR: LARAR1=0x%08x\n", ecm->lawar1); + + /* + * Confirm that the requested amount of memory was mapped. + */ + return memsize; +} + #endif /* CONFIG_SPD_EEPROM */ -#if defined(CONFIG_DDR_ECC) +#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER) + /* * Initialize all of memory for ECC, then enable errors. */ + void ddr_enable_ecc(unsigned int dram_size) { @@ -420,7 +1075,7 @@ ddr_enable_ecc(unsigned int dram_size) if (((unsigned int)p & 0x1f) == 0) { ppcDcbz((unsigned long) p); } - *p = (unsigned int)0xdeadbeef; + *p = (unsigned int)CONFIG_MEM_INIT_VALUE; if (((unsigned int)p & 0x1c) == 0x1c) { ppcDcbf((unsigned long) p); } @@ -454,7 +1109,10 @@ ddr_enable_ecc(unsigned int dram_size) /* * Enable errors for ECC. */ + debug("DMA DDR: err_disable = 0x%08x\n", ddr->err_disable); ddr->err_disable = 0x00000000; asm("sync;isync;msync"); + debug("DMA DDR: err_disable = 0x%08x\n", ddr->err_disable); } -#endif /* CONFIG_DDR_ECC */ + +#endif /* CONFIG_DDR_ECC && ! CONFIG_ECC_INIT_VIA_DDRCONTROLLER */ diff --git a/cpu/mpc85xx/start.S b/cpu/mpc85xx/start.S index 7bca008b58..dd8189931a 100644 --- a/cpu/mpc85xx/start.S +++ b/cpu/mpc85xx/start.S @@ -174,6 +174,9 @@ _start_e500: mtspr BUCSR,r0 /* disable branch prediction */ mtspr MAS4,r0 mtspr MAS6,r0 +#if defined(CONFIG_ENABLE_36BIT_PHYS) + mtspr MAS7,r0 +#endif isync /* Setup interrupt vectors */ @@ -358,6 +361,9 @@ _start: /* Enable Time Base and Select Time Base Clock */ lis r0,HID0_EMCP@h /* Enable machine check */ ori r0,r0,0x4000 /* time base is processor clock */ +#if defined(CONFIG_ENABLE_36BIT_PHYS) + ori r0,r0,0x0080 /* enable MAS7 updates */ +#endif mtspr HID0,r0 #if defined(CONFIG_ADDR_STREAMING) diff --git a/cpu/mpc85xx/tsec.c b/cpu/mpc85xx/tsec.c index d327a6decb..5ac6334322 100644 --- a/cpu/mpc85xx/tsec.c +++ b/cpu/mpc85xx/tsec.c @@ -35,7 +35,7 @@ typedef volatile struct rtxbd { struct tsec_info_struct { unsigned int phyaddr; - unsigned int gigabit; + u32 flags; unsigned int phyregidx; }; @@ -48,8 +48,9 @@ struct tsec_info_struct { * phyaddr - The address of the PHY which is attached to * the given device. * - * gigabit - This variable indicates whether the device - * supports gigabit speed ethernet + * flags - This variable indicates whether the device + * supports gigabit speed ethernet, and whether it should be + * in reduced mode. * * phyregidx - This variable specifies which ethernet device * controls the MII Management registers which are connected @@ -70,23 +71,32 @@ struct tsec_info_struct { */ static struct tsec_info_struct tsec_info[] = { #ifdef CONFIG_MPC85XX_TSEC1 - {TSEC1_PHY_ADDR, 1, TSEC1_PHYIDX}, + {TSEC1_PHY_ADDR, TSEC_GIGABIT, TSEC1_PHYIDX}, #else { 0, 0, 0}, #endif #ifdef CONFIG_MPC85XX_TSEC2 - {TSEC2_PHY_ADDR, 1, TSEC2_PHYIDX}, + {TSEC2_PHY_ADDR, TSEC_GIGABIT, TSEC2_PHYIDX}, #else { 0, 0, 0}, #endif #ifdef CONFIG_MPC85XX_FEC {FEC_PHY_ADDR, 0, FEC_PHYIDX}, #else +# ifdef CONFIG_MPC85XX_TSEC3 + {TSEC3_PHY_ADDR, TSEC_GIGABIT | TSEC_REDUCED, TSEC3_PHYIDX}, +# else { 0, 0, 0}, +# endif +# ifdef CONFIG_MPC85XX_TSEC4 + {TSEC4_PHY_ADDR, TSEC_REDUCED, TSEC4_PHYIDX}, +# else + { 0, 0, 0}, +# endif #endif }; -#define MAXCONTROLLERS 3 +#define MAXCONTROLLERS (4) static int relocated = 0; @@ -115,7 +125,7 @@ static void relocate_cmds(void); /* Initialize device structure. Returns success if PHY * initialization succeeded (i.e. if it recognizes the PHY) */ -int tsec_initialize(bd_t *bis, int index) +int tsec_initialize(bd_t *bis, int index, char *devname) { struct eth_device* dev; int i; @@ -139,9 +149,9 @@ int tsec_initialize(bd_t *bis, int index) tsec_info[index].phyregidx*TSEC_SIZE); priv->phyaddr = tsec_info[index].phyaddr; - priv->gigabit = tsec_info[index].gigabit; + priv->flags = tsec_info[index].flags; - sprintf(dev->name, "ENET%d", index); + sprintf(dev->name, devname); dev->iobase = 0; dev->priv = priv; dev->init = tsec_init; @@ -318,7 +328,7 @@ static int init_phy(struct eth_device *dev) /* For 10/100, the value is slightly different */ uint mii_cr_init(uint mii_reg, struct tsec_private *priv) { - if(priv->gigabit) + if(priv->flags & TSEC_GIGABIT) return MIIM_CONTROL_INIT; else return MIIM_CR_INIT; @@ -438,6 +448,13 @@ uint mii_cis8204_fixled(uint mii_reg, struct tsec_private *priv) return MIIM_CIS8204_SLEDCON_INIT; } +uint mii_cis8204_setmode(uint mii_reg, struct tsec_private *priv) +{ + if (priv->flags & TSEC_REDUCED) + return MIIM_CIS8204_EPHYCON_INIT | MIIM_CIS8204_EPHYCON_RGMII; + else + return MIIM_CIS8204_EPHYCON_INIT; +} /* Initialized required registers to appropriate values, zeroing * those we don't care about (unless zero is bad, in which case, @@ -507,6 +524,15 @@ static void adjust_link(struct eth_device *dev) case 10: regs->maccfg2 = ((regs->maccfg2&~(MACCFG2_IF)) | MACCFG2_MII); + + /* If We're in reduced mode, we + * need to say whether we're 10 + * or 100 MB. */ + if ((priv->speed == 100) + && (priv->flags & TSEC_REDUCED)) + regs->ecntrl |= ECNTRL_R100; + else + regs->ecntrl &= ~(ECNTRL_R100); break; default: printf("%s: Speed was bad\n", dev->name); @@ -731,7 +757,7 @@ struct phy_info phy_info_cis8204 = { /* Configure some basic stuff */ {MIIM_CONTROL, MIIM_CONTROL_INIT, &mii_cr_init}, {MIIM_CIS8204_SLED_CON, MIIM_CIS8204_SLEDCON_INIT, &mii_cis8204_fixled}, - {MIIM_CIS8204_EPHY_CON, MIIM_CIS8204_EPHYCON_INIT, NULL}, + {MIIM_CIS8204_EPHY_CON, MIIM_CIS8204_EPHYCON_INIT, &mii_cis8204_setmode}, {miim_end,} }, (struct phy_cmd[]) { /* startup */ diff --git a/cpu/mpc85xx/tsec.h b/cpu/mpc85xx/tsec.h index e24351a2e9..d1c70aa89f 100644 --- a/cpu/mpc85xx/tsec.h +++ b/cpu/mpc85xx/tsec.h @@ -51,6 +51,7 @@ #define ECNTRL_INIT_SETTINGS 0x00001000 #define ECNTRL_TBI_MODE 0x00000020 +#define ECNTRL_R100 0x00000008 #define miim_end -2 #define miim_read -1 @@ -107,6 +108,7 @@ /* Cicada 8204 Extended PHY Control Register 1 */ #define MIIM_CIS8204_EPHY_CON 0x17 #define MIIM_CIS8204_EPHYCON_INIT 0x0006 +#define MIIM_CIS8204_EPHYCON_RGMII 0x1000 /* Cicada 8204 Serial LED Control Register */ #define MIIM_CIS8204_SLED_CON 0x1b @@ -424,12 +426,18 @@ typedef struct tsec uint resc00[256]; } tsec_t; +#define TSEC_GIGABIT (1) + +/* This flag currently only has + * meaning if we're using the eTSEC */ +#define TSEC_REDUCED (1 << 1) + struct tsec_private { volatile tsec_t *regs; volatile tsec_t *phyregs; struct phy_info *phyinfo; uint phyaddr; - uint gigabit; + u32 flags; uint link; uint duplexity; uint speed; diff --git a/doc/README.mpc85xxads b/doc/README.mpc85xxads index c488f2a56b..08d6831fb6 100644 --- a/doc/README.mpc85xxads +++ b/doc/README.mpc85xxads @@ -143,6 +143,7 @@ Updated 13-July-2004 Jon Loeliger CONFIG_DDR_ECC only for ECC DDR module CONFIG_DDR_DLL DLL fix on some ADS boards needed for more stability. + CONFIG_HAS_FEC If an FEC is on chip, set to 1, else 0. Other than the above definitions, the rest in the config files are straightforward. @@ -190,10 +191,10 @@ straightforward. 4.4 Reflash U-boot Image using U-boot - => tftp 10000 u-boot.bin - => protect off fff80000 ffffffff - => erase fff80000 ffffffff - => cp.b 10000 fff80000 80000 + tftp 10000 u-boot.bin + protect off fff80000 ffffffff + erase fff80000 ffffffff + cp.b 10000 fff80000 80000 4.5 Reflash U-Boot with a BDI-2000 diff --git a/doc/README.mpc85xxcds b/doc/README.mpc85xxcds index e0f49163ed..bc5db0ca8e 100644 --- a/doc/README.mpc85xxcds +++ b/doc/README.mpc85xxcds @@ -135,8 +135,8 @@ The default setting of all switches on the carrier board is: SW4=10001000 -CPU Card Switches ------------------ +8555/41 CPU Card Switches +------------------------- Most switches on the CPU Card should not be changed. However, the frequency can be changed by setting SW3: @@ -160,6 +160,45 @@ A safe default setting for all switches on the CPU board is: SW4=11111110 +8548 CPU Card Switches +---------------------- +And, just to be confusing, in this set of switches: + + ON = 1 + OFF = 0 + +Default + SW1=11111101 + SW2=10011111 + SW3=11001000 (8X) (2:1) + SW4=11110011 + + SW3=X000XXXX == CORE:CCB 4:1 + X001XXXX == CORE:CCB 9:2 + X010XXXX == CORE:CCB 1:1 + X011XXXX == CORE:CCB 3:2 + X100XXXX == CORE:CCB 2:1 + X101XXXX == CORE:CCB 5:2 + X110XXXX == CORE:CCB 3:1 + X111XXXX == CORE:CCB 7:2 + XXXX0000 == CCB:SYSCLK 16:1 + XXXX0001 == RESERVED + XXXX0010 == CCB:SYSCLK 2:1 + XXXX0011 == CCB:SYSCLK 3:1 + XXXX0100 == CCB:SYSCLK 4:1 + XXXX0101 == CCB:SYSCLK 5:1 + XXXX0110 == CCB:SYSCLK 6:1 + XXXX0111 == RESERVED + XXXX1000 == CCB:SYSCLK 8:1 + XXXX1001 == CCB:SYSCLK 9:1 + XXXX1010 == CCB:SYSCLK 10:1 + XXXX1011 == RESERVED + XXXX1100 == CCB:SYSCLK 12:1 + XXXX1101 == CCB:SYSCLK 20:1 + XXXX1110 == RESERVED + XXXX1111 == RESERVED + + eDINK Info ---------- diff --git a/include/asm-ppc/immap_85xx.h b/include/asm-ppc/immap_85xx.h index e9bb989021..22f19f0858 100644 --- a/include/asm-ppc/immap_85xx.h +++ b/include/asm-ppc/immap_85xx.h @@ -81,21 +81,27 @@ typedef struct ccsr_ddr { uint cs1_config; /* 0x2084 - DDR Chip Select Configuration */ uint cs2_config; /* 0x2088 - DDR Chip Select Configuration */ uint cs3_config; /* 0x208c - DDR Chip Select Configuration */ - char res5[120]; + char res5[112]; + uint ext_refrec; /* 0x2100 - DDR SDRAM Extended Refresh Recovery */ + uint timing_cfg_0; /* 0x2104 - DDR SDRAM Timing Configuration Register 0 */ uint timing_cfg_1; /* 0x2108 - DDR SDRAM Timing Configuration Register 1 */ uint timing_cfg_2; /* 0x210c - DDR SDRAM Timing Configuration Register 2 */ uint sdram_cfg; /* 0x2110 - DDR SDRAM Control Configuration */ - char res6[4]; + uint sdram_cfg_2; /* 0x2114 - DDR SDRAM Control Configuration 2 */ uint sdram_mode; /* 0x2118 - DDR SDRAM Mode Configuration */ - char res7[8]; + uint sdram_mode_2; /* 0x211c - DDR SDRAM Mode Configuration 2*/ + uint sdram_md_cntl; /* 0x2120 - DDR SDRAM Mode Control */ uint sdram_interval; /* 0x2124 - DDR SDRAM Interval Configuration */ -#ifdef MPC85xx_DDR_SDRAM_CLK_CNTL - char res7_5[8]; + uint sdram_data_init; /* 0x2128 - DDR SDRAM Data initialization */ + char res6[4]; uint sdram_clk_cntl; /* 0x2130 - DDR SDRAM Clock Control */ - char res8[3276]; -#else - char res8[3288]; -#endif + char res7[20]; + uint init_address; /* 0x2148 - DDR training initialization address */ + uint init_ext_address; /* 0x214C - DDR training initialization extended address */ + char res8_1[2728]; + uint ip_rev1; /* 0x2BF8 - DDR IP Block Revision 1 */ + uint ip_rev2; /* 0x2BFC - DDR IP Block Revision 2 */ + char res8_2[512]; uint data_err_inject_hi; /* 0x2e00 - DDR Memory Data Path Error Injection Mask High */ uint data_err_inject_lo; /* 0x2e04 - DDR Memory Data Path Error Injection Mask Low */ uint ecc_err_inject; /* 0x2e08 - DDR Memory Data Path Error Injection Mask ECC */ @@ -120,6 +126,8 @@ typedef struct ccsr_ddr { } ccsr_ddr_t; + + /* I2C Registers(0x3000-0x4000) */ typedef struct ccsr_i2c { @@ -158,6 +166,7 @@ typedef struct ccsr_i2c { #if defined(CONFIG_MPC8540) \ || defined(CONFIG_MPC8541) \ + || defined(CONFIG_MPC8548) \ || defined(CONFIG_MPC8555) /* DUART Registers(0x4000-0x5000) */ typedef struct ccsr_duart { @@ -1547,7 +1556,13 @@ typedef struct ccsr_gur { uint ddrdllcr; /* 0xe0e10 - DDR DLL control register */ char res12[12]; uint lbcdllcr; /* 0xe0e20 - LBC DLL control register */ - char res13[61915]; + char res13[248]; + uint lbiuiplldcr0; /* 0xe0f1c -- LBIU PLL Debug Reg 0 */ + uint lbiuiplldcr1; /* 0xe0f20 -- LBIU PLL Debug Reg 1 */ + uint ddrioovcr; /* 0xe0f24 - DDR IO Override Control */ + uint res14; /* 0xe0f28 */ + uint tsec34ioovcr; /* 0xe0f2c - eTSEC 3/4 IO override control */ + char res15[61651]; } ccsr_gur_t; typedef struct immap { diff --git a/include/asm-ppc/processor.h b/include/asm-ppc/processor.h index 71fadbc918..20949dcc39 100644 --- a/include/asm-ppc/processor.h +++ b/include/asm-ppc/processor.h @@ -420,6 +420,7 @@ #define SPRN_MAS4 0x274 /* MMU Assist Register 4 */ #define SPRN_MAS5 0x275 /* MMU Assist Register 5 */ #define SPRN_MAS6 0x276 /* MMU Assist Register 6 */ +#define SPRN_MAS7 0x3B0 /* MMU Assist Register 7 */ #define SPRN_IVOR32 0x210 /* Interrupt Vector Offset Register 32 */ #define SPRN_IVOR33 0x211 /* Interrupt Vector Offset Register 33 */ @@ -584,6 +585,7 @@ #define MAS4 SPRN_MAS4 #define MAS5 SPRN_MAS5 #define MAS6 SPRN_MAS6 +#define MAS7 SPRN_MAS7 /* Device Control Registers */ @@ -792,6 +794,8 @@ #define SVR_8560 0x8070 #define SVR_8555 0x8079 #define SVR_8541 0x807A +#define SVR_8548 0x8031 +#define SVR_8548_E 0x8039 /* I am just adding a single entry for 8260 boards. I think we may be diff --git a/include/configs/MPC8540ADS.h b/include/configs/MPC8540ADS.h index 533b587966..131c832242 100644 --- a/include/configs/MPC8540ADS.h +++ b/include/configs/MPC8540ADS.h @@ -49,10 +49,12 @@ #define CONFIG_TSEC_ENET /* tsec ethernet support */ #define CONFIG_ENV_OVERWRITE #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ -#define CONFIG_DDR_ECC /* only for ECC DDR module */ #define CONFIG_DDR_DLL /* possible DLL fix needed */ #define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */ +#define CONFIG_DDR_ECC /* only for ECC DDR module */ +#define CONFIG_MEM_INIT_VALUE 0xDeadBeef + /* * sysclk for MPC85xx @@ -342,7 +344,9 @@ #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_MPC85XX_TSEC1 1 +#define CONFIG_MPC85XX_TSEC1_NAME "TSEC0" #define CONFIG_MPC85XX_TSEC2 1 +#define CONFIG_MPC85XX_TSEC2_NAME "TSEC1" #define TSEC1_PHY_ADDR 0 #define TSEC2_PHY_ADDR 1 #define TSEC1_PHYIDX 0 @@ -351,11 +355,13 @@ #if CONFIG_HAS_FEC #define CONFIG_MPC85XX_FEC 1 +#define CONFIG_MPC85XX_FEC_NAME "FEC" #define FEC_PHY_ADDR 3 #define FEC_PHYIDX 0 #endif -#define CONFIG_ETHPRIME "MOTO ENET0" +/* Options are: TSEC[0-1], FEC */ +#define CONFIG_ETHPRIME "TSEC0" #endif /* CONFIG_TSEC_ENET */ diff --git a/include/configs/MPC8541CDS.h b/include/configs/MPC8541CDS.h index 3ec27b8aae..c96b98b54d 100644 --- a/include/configs/MPC8541CDS.h +++ b/include/configs/MPC8541CDS.h @@ -41,9 +41,12 @@ #define CONFIG_TSEC_ENET /* tsec ethernet support */ #define CONFIG_ENV_OVERWRITE #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ -#define CONFIG_DDR_ECC /* only for ECC DDR module */ #define CONFIG_DDR_DLL /* possible DLL fix needed */ -#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */ +#undef CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */ + +#define CONFIG_DDR_ECC /* only for ECC DDR module */ +#define CONFIG_MEM_INIT_VALUE 0xDeadBeef + /* * When initializing flash, if we cannot find the manufacturer ID, @@ -360,7 +363,9 @@ extern unsigned long get_clock_freq(void); #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_MPC85XX_TSEC1 1 +#define CONFIG_MPC85XX_TSEC1_NAME "TSEC0" #define CONFIG_MPC85XX_TSEC2 1 +#define CONFIG_MPC85XX_TSEC2_NAME "TSEC1" #undef CONFIG_MPC85XX_FEC #define TSEC1_PHY_ADDR 0 #define TSEC2_PHY_ADDR 1 @@ -368,7 +373,9 @@ extern unsigned long get_clock_freq(void); #define TSEC1_PHYIDX 0 #define TSEC2_PHYIDX 0 #define FEC_PHYIDX 0 -#define CONFIG_ETHPRIME "MOTO ENET0" + +/* Options are: TSEC[0-1] */ +#define CONFIG_ETHPRIME "TSEC0" #endif /* CONFIG_TSEC_ENET */ diff --git a/include/configs/MPC8548CDS.h b/include/configs/MPC8548CDS.h new file mode 100644 index 0000000000..4ca8bc35db --- /dev/null +++ b/include/configs/MPC8548CDS.h @@ -0,0 +1,521 @@ +/* + * Copyright 2004 Freescale Semiconductor. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * mpc8548cds board configuration file + * + * Please refer to doc/README.mpc85xxcds for more info. + * + */ +#ifndef __CONFIG_H +#define __CONFIG_H + +/* High Level Configuration Options */ +#define CONFIG_BOOKE 1 /* BOOKE */ +#define CONFIG_E500 1 /* BOOKE e500 family */ +#define CONFIG_MPC85xx 1 /* MPC8540/60/55/41/48 */ +#define CONFIG_MPC8548 1 /* MPC8548 specific */ +#define CONFIG_MPC8548CDS 1 /* MPC8548CDS board specific */ + +#undef CONFIG_PCI +#define CONFIG_TSEC_ENET /* tsec ethernet support */ +#define CONFIG_ENV_OVERWRITE +#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ +#define CONFIG_DDR_DLL /* possible DLL fix needed */ +#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */ + +#define CONFIG_DDR_ECC /* only for ECC DDR module */ +#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ +#define CONFIG_MEM_INIT_VALUE 0xDeadBeef + + +/* + * When initializing flash, if we cannot find the manufacturer ID, + * assume this is the AMD flash associated with the CDS board. + * This allows booting from a promjet. + */ +#define CONFIG_ASSUME_AMD_FLASH + +#define MPC85xx_DDR_SDRAM_CLK_CNTL /* 85xx has clock control reg */ + +#ifndef __ASSEMBLY__ +extern unsigned long get_clock_freq(void); +#endif +#define CONFIG_SYS_CLK_FREQ get_clock_freq() /* sysclk for MPC85xx */ + +/* + * These can be toggled for performance analysis, otherwise use default. + */ +#define CONFIG_L2_CACHE /* toggle L2 cache */ +#define CONFIG_BTB /* toggle branch predition */ +#define CONFIG_ADDR_STREAMING /* toggle addr streaming */ + +/* + * Only possible on E500 Version 2 or newer cores. + */ +#define CONFIG_ENABLE_36BIT_PHYS 1 + + +#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ + +#undef CFG_DRAM_TEST /* memory test, takes time */ +#define CFG_MEMTEST_START 0x00200000 /* memtest works on */ +#define CFG_MEMTEST_END 0x00400000 + +/* + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + */ +#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ +#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */ +#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */ + +/* + * DDR Setup + */ +#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ +#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE + +#define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */ + +/* + * Make sure required options are set + */ +#ifndef CONFIG_SPD_EEPROM +#error ("CONFIG_SPD_EEPROM is required") +#endif + +#undef CONFIG_CLOCKS_IN_MHZ + + +/* + * Local Bus Definitions + */ + +/* + * FLASH on the Local Bus + * Two banks, 8M each, using the CFI driver. + * Boot from BR0/OR0 bank at 0xff00_0000 + * Alternate BR1/OR1 bank at 0xff80_0000 + * + * BR0, BR1: + * Base address 0 = 0xff00_0000 = BR0[0:16] = 1111 1111 0000 0000 0 + * Base address 1 = 0xff80_0000 = BR1[0:16] = 1111 1111 1000 0000 0 + * Port Size = 16 bits = BRx[19:20] = 10 + * Use GPCM = BRx[24:26] = 000 + * Valid = BRx[31] = 1 + * + * 0 4 8 12 16 20 24 28 + * 1111 1111 1000 0000 0001 0000 0000 0001 = ff801001 BR0 + * 1111 1111 0000 0000 0001 0000 0000 0001 = ff001001 BR1 + * + * OR0, OR1: + * Addr Mask = 8M = ORx[0:16] = 1111 1111 1000 0000 0 + * Reserved ORx[17:18] = 11, confusion here? + * CSNT = ORx[20] = 1 + * ACS = half cycle delay = ORx[21:22] = 11 + * SCY = 6 = ORx[24:27] = 0110 + * TRLX = use relaxed timing = ORx[29] = 1 + * EAD = use external address latch delay = OR[31] = 1 + * + * 0 4 8 12 16 20 24 28 + * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65 ORx + */ + +#define CFG_FLASH_BASE 0xff000000 /* start of FLASH 8M */ + +#define CFG_BR0_PRELIM 0xff801001 +#define CFG_BR1_PRELIM 0xff001001 + +#define CFG_OR0_PRELIM 0xff806e65 +#define CFG_OR1_PRELIM 0xff806e65 + +#define CFG_FLASH_BANKS_LIST {0xff800000, CFG_FLASH_BASE} +#define CFG_MAX_FLASH_BANKS 2 /* number of banks */ +#define CFG_MAX_FLASH_SECT 128 /* sectors per device */ +#undef CFG_FLASH_CHECKSUM +#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ + +#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ + +#define CFG_FLASH_CFI_DRIVER +#define CFG_FLASH_CFI +#define CFG_FLASH_EMPTY_INFO + + +/* + * SDRAM on the Local Bus + */ +#define CFG_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */ +#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ + +/* + * Base Register 2 and Option Register 2 configure SDRAM. + * The SDRAM base address, CFG_LBC_SDRAM_BASE, is 0xf0000000. + * + * For BR2, need: + * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0 + * port-size = 32-bits = BR2[19:20] = 11 + * no parity checking = BR2[21:22] = 00 + * SDRAM for MSEL = BR2[24:26] = 011 + * Valid = BR[31] = 1 + * + * 0 4 8 12 16 20 24 28 + * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861 + * + * FIXME: CFG_LBC_SDRAM_BASE should be masked and OR'ed into + * FIXME: the top 17 bits of BR2. + */ + +#define CFG_BR2_PRELIM 0xf0001861 + +/* + * The SDRAM size in MB, CFG_LBC_SDRAM_SIZE, is 64. + * + * For OR2, need: + * 64MB mask for AM, OR2[0:7] = 1111 1100 + * XAM, OR2[17:18] = 11 + * 9 columns OR2[19-21] = 010 + * 13 rows OR2[23-25] = 100 + * EAD set for extra time OR[31] = 1 + * + * 0 4 8 12 16 20 24 28 + * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901 + */ + +#define CFG_OR2_PRELIM 0xfc006901 + +#define CFG_LBC_LCRR 0x00030004 /* LB clock ratio reg */ +#define CFG_LBC_LBCR 0x00000000 /* LB config reg */ +#define CFG_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ +#define CFG_LBC_MRTPR 0x00000000 /* LB refresh timer prescal*/ + +/* + * LSDMR masks + */ +#define CFG_LBC_LSDMR_RFEN (1 << (31 - 1)) +#define CFG_LBC_LSDMR_BSMA1516 (3 << (31 - 10)) +#define CFG_LBC_LSDMR_BSMA1617 (4 << (31 - 10)) +#define CFG_LBC_LSDMR_RFCR16 (7 << (31 - 16)) +#define CFG_LBC_LSDMR_PRETOACT7 (7 << (31 - 19)) +#define CFG_LBC_LSDMR_ACTTORW7 (7 << (31 - 22)) +#define CFG_LBC_LSDMR_ACTTORW6 (6 << (31 - 22)) +#define CFG_LBC_LSDMR_BL8 (1 << (31 - 23)) +#define CFG_LBC_LSDMR_WRC4 (0 << (31 - 27)) +#define CFG_LBC_LSDMR_CL3 (3 << (31 - 31)) + +#define CFG_LBC_LSDMR_OP_NORMAL (0 << (31 - 4)) +#define CFG_LBC_LSDMR_OP_ARFRSH (1 << (31 - 4)) +#define CFG_LBC_LSDMR_OP_SRFRSH (2 << (31 - 4)) +#define CFG_LBC_LSDMR_OP_MRW (3 << (31 - 4)) +#define CFG_LBC_LSDMR_OP_PRECH (4 << (31 - 4)) +#define CFG_LBC_LSDMR_OP_PCHALL (5 << (31 - 4)) +#define CFG_LBC_LSDMR_OP_ACTBNK (6 << (31 - 4)) +#define CFG_LBC_LSDMR_OP_RWINV (7 << (31 - 4)) + +/* + * Common settings for all Local Bus SDRAM commands. + * At run time, either BSMA1516 (for CPU 1.1) + * or BSMA1617 (for CPU 1.0) (old) + * is OR'ed in too. + */ +#define CFG_LBC_LSDMR_COMMON ( CFG_LBC_LSDMR_RFCR16 \ + | CFG_LBC_LSDMR_PRETOACT7 \ + | CFG_LBC_LSDMR_ACTTORW7 \ + | CFG_LBC_LSDMR_BL8 \ + | CFG_LBC_LSDMR_WRC4 \ + | CFG_LBC_LSDMR_CL3 \ + | CFG_LBC_LSDMR_RFEN \ + ) + +/* + * The CADMUS registers are connected to CS3 on CDS. + * The new memory map places CADMUS at 0xf8000000. + * + * For BR3, need: + * Base address of 0xf8000000 = BR[0:16] = 1111 1000 0000 0000 0 + * port-size = 8-bits = BR[19:20] = 01 + * no parity checking = BR[21:22] = 00 + * GPMC for MSEL = BR[24:26] = 000 + * Valid = BR[31] = 1 + * + * 0 4 8 12 16 20 24 28 + * 1111 1000 0000 0000 0000 1000 0000 0001 = f8000801 + * + * For OR3, need: + * 1 MB mask for AM, OR[0:16] = 1111 1111 1111 0000 0 + * disable buffer ctrl OR[19] = 0 + * CSNT OR[20] = 1 + * ACS OR[21:22] = 11 + * XACS OR[23] = 1 + * SCY 15 wait states OR[24:27] = 1111 max is suboptimal but safe + * SETA OR[28] = 0 + * TRLX OR[29] = 1 + * EHTR OR[30] = 1 + * EAD extra time OR[31] = 1 + * + * 0 4 8 12 16 20 24 28 + * 1111 1111 1111 0000 0000 1111 1111 0111 = fff00ff7 + */ + +#define CADMUS_BASE_ADDR 0xf8000000 +#define CFG_BR3_PRELIM 0xf8000801 +#define CFG_OR3_PRELIM 0xfff00ff7 + +#define CONFIG_L1_INIT_RAM +#define CFG_INIT_RAM_LOCK 1 +#define CFG_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ +#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */ + +#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ +#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ + +/* Serial Port */ +#define CONFIG_CONS_INDEX 2 +#undef CONFIG_SERIAL_SOFTWARE_FIFO +#define CFG_NS16550 +#define CFG_NS16550_SERIAL +#define CFG_NS16550_REG_SIZE 1 +#define CFG_NS16550_CLK get_bus_freq(0) + +#define CFG_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} + +#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500) +#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600) + +/* Use the HUSH parser */ +#define CFG_HUSH_PARSER +#ifdef CFG_HUSH_PARSER +#define CFG_PROMPT_HUSH_PS2 "> " +#endif + +/* I2C */ +#define CONFIG_HARD_I2C /* I2C with hardware support */ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_EEPROM_ADDR 0x57 +#define CFG_I2C_SLAVE 0x7F +#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */ + +/* + * General PCI + * Addresses are mapped 1-1. + */ +#define CFG_PCI1_MEM_BASE 0x80000000 +#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE +#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */ +#define CFG_PCI1_IO_BASE 0xe2000000 +#define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE +#define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */ + +#define CFG_PCI2_MEM_BASE 0xa0000000 +#define CFG_PCI2_MEM_PHYS CFG_PCI2_MEM_BASE +#define CFG_PCI2_MEM_SIZE 0x20000000 /* 512M */ +#define CFG_PCI2_IO_BASE 0xe3000000 +#define CFG_PCI2_IO_PHYS CFG_PCI2_IO_BASE +#define CFG_PCI2_IO_SIZE 0x1000000 /* 16M */ + + +#if defined(CONFIG_PCI) + +#define CONFIG_NET_MULTI +#define CONFIG_PCI_PNP /* do pci plug-and-play */ + +#undef CONFIG_EEPRO100 +#undef CONFIG_TULIP + +#if !defined(CONFIG_PCI_PNP) + #define PCI_ENET0_IOADDR 0xe0000000 + #define PCI_ENET0_MEMADDR 0xe0000000 + #define PCI_IDSEL_NUMBER 0x0c /*slot0->3(IDSEL)=12->15*/ +#endif + +#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ + +#endif /* CONFIG_PCI */ + + +#if defined(CONFIG_TSEC_ENET) + +#ifndef CONFIG_NET_MULTI +#define CONFIG_NET_MULTI 1 +#endif + +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_MPC85XX_TSEC1 1 +#define CONFIG_MPC85XX_TSEC1_NAME "eTSEC0" +#define CONFIG_MPC85XX_TSEC2 1 +#define CONFIG_MPC85XX_TSEC2_NAME "eTSEC1" +#define CONFIG_MPC85XX_TSEC3 1 +#define CONFIG_MPC85XX_TSEC3_NAME "eTSEC2" +#define CONFIG_MPC85XX_TSEC4 1 +#define CONFIG_MPC85XX_TSEC4_NAME "eTSEC3" +#undef CONFIG_MPC85XX_FEC + +#define TSEC1_PHY_ADDR 0 +#define TSEC2_PHY_ADDR 1 +#define TSEC3_PHY_ADDR 2 +#define TSEC4_PHY_ADDR 3 +#define FEC_PHY_ADDR 3 + +#define TSEC1_PHYIDX 0 +#define TSEC2_PHYIDX 0 +#define TSEC3_PHYIDX 0 +#define TSEC4_PHYIDX 0 +#define FEC_PHYIDX 0 + +/* Options are: eTSEC[0-3] */ +#define CONFIG_ETHPRIME "eTSEC0" + +#endif /* CONFIG_TSEC_ENET */ + +/* + * Environment + */ +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000) +#define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */ +#define CFG_ENV_SIZE 0x2000 + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +#if defined(CONFIG_PCI) +#define CONFIG_COMMANDS (CONFIG_CMD_DFL \ + | CFG_CMD_PCI \ + | CFG_CMD_PING \ + | CFG_CMD_I2C \ + | CFG_CMD_MII) +#else +#define CONFIG_COMMANDS (CONFIG_CMD_DFL \ + | CFG_CMD_PING \ + | CFG_CMD_I2C \ + | CFG_CMD_MII) +#endif +#include + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_LOAD_ADDR 0x2000000 /* default load address */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ + +/* Cache Configuration */ +#define CFG_DCACHE_SIZE 32768 +#define CFG_CACHELINE_SIZE 32 +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ +#endif + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * Environment Configuration + */ + +/* The mac addresses for all ethernet interface */ +#if defined(CONFIG_TSEC_ENET) +#define CONFIG_ETHADDR 00:E0:0C:00:00:FD +#define CONFIG_HAS_ETH1 +#define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD +#define CONFIG_HAS_ETH2 +#define CONFIG_ETH2ADDR 00:E0:0C:00:02:FD +#endif + +#define CONFIG_IPADDR 192.168.1.253 + +#define CONFIG_HOSTNAME unknown +#define CONFIG_ROOTPATH /nfsroot +#define CONFIG_BOOTFILE your.uImage + +#define CONFIG_SERVERIP 192.168.1.1 +#define CONFIG_GATEWAYIP 192.168.1.1 +#define CONFIG_NETMASK 255.255.255.0 + +#define CONFIG_LOADADDR 200000 /*default location for tftp and bootm*/ + +#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ +#undef CONFIG_BOOTARGS /* the boot command will set bootargs*/ + +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "consoledev=ttyS1\0" \ + "ramdiskaddr=400000\0" \ + "ramdiskfile=your.ramdisk.u-boot\0" + +#define CONFIG_NFSBOOTCOMMAND \ + "setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$serverip:$rootpath " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "bootm $loadaddr" + +#define CONFIG_RAMBOOTCOMMAND \ + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $ramdiskaddr $ramdiskfile;" \ + "tftp $loadaddr $bootfile;" \ + "bootm $loadaddr $ramdiskaddr" + +#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND + +#endif /* __CONFIG_H */ diff --git a/include/configs/MPC8555CDS.h b/include/configs/MPC8555CDS.h index 7967e9069d..a44e3ec845 100644 --- a/include/configs/MPC8555CDS.h +++ b/include/configs/MPC8555CDS.h @@ -41,9 +41,12 @@ #define CONFIG_TSEC_ENET /* tsec ethernet support */ #define CONFIG_ENV_OVERWRITE #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ -#define CONFIG_DDR_ECC /* only for ECC DDR module */ #define CONFIG_DDR_DLL /* possible DLL fix needed */ -#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */ +#undef CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */ + +#define CONFIG_DDR_ECC /* only for ECC DDR module */ +#define CONFIG_MEM_INIT_VALUE 0xDeadBeef + /* * When initializing flash, if we cannot find the manufacturer ID, @@ -360,7 +363,9 @@ extern unsigned long get_clock_freq(void); #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_MPC85XX_TSEC1 1 +#define CONFIG_MPC85XX_TSEC1_NAME "TSEC0" #define CONFIG_MPC85XX_TSEC2 1 +#define CONFIG_MPC85XX_TSEC2_NAME "TSEC1" #undef CONFIG_MPC85XX_FEC #define TSEC1_PHY_ADDR 0 #define TSEC2_PHY_ADDR 1 @@ -368,7 +373,9 @@ extern unsigned long get_clock_freq(void); #define TSEC1_PHYIDX 0 #define TSEC2_PHYIDX 0 #define FEC_PHYIDX 0 -#define CONFIG_ETHPRIME "MOTO ENET0" + +/* Options are: TSEC[0-1] */ +#define CONFIG_ETHPRIME "TSEC0" #endif /* CONFIG_TSEC_ENET */ diff --git a/include/configs/MPC8560ADS.h b/include/configs/MPC8560ADS.h index e1a2bba8a0..db878cb193 100644 --- a/include/configs/MPC8560ADS.h +++ b/include/configs/MPC8560ADS.h @@ -46,10 +46,12 @@ #undef CONFIG_ETHER_ON_FCC /* cpm FCC ethernet support */ #define CONFIG_ENV_OVERWRITE #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ -#define CONFIG_DDR_ECC /* only for ECC DDR module */ #define CONFIG_DDR_DLL /* possible DLL fix needed */ #define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */ +#define CONFIG_DDR_ECC /* only for ECC DDR module */ +#define CONFIG_MEM_INIT_VALUE 0xDeadBeef + /* * sysclk for MPC85xx @@ -337,13 +339,17 @@ #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_MPC85XX_TSEC1 1 +#define CONFIG_MPC85XX_TSEC1_NAME "TSEC0" #define CONFIG_MPC85XX_TSEC2 1 +#define CONFIG_MPC85XX_TSEC2_NAME "TSEC1" #undef CONFIG_MPC85XX_FEC #define TSEC1_PHY_ADDR 0 #define TSEC2_PHY_ADDR 1 #define TSEC1_PHYIDX 0 #define TSEC2_PHYIDX 0 -#define CONFIG_ETHPRIME "MOTO ENET0" + +/* Options are: TSEC[0-1] */ +#define CONFIG_ETHPRIME "TSEC0" #elif defined(CONFIG_ETHER_ON_FCC) /* CPM FCC Ethernet */ diff --git a/include/configs/PM854.h b/include/configs/PM854.h index 69e1bafcfd..12a71812b5 100644 --- a/include/configs/PM854.h +++ b/include/configs/PM854.h @@ -45,10 +45,12 @@ #define CONFIG_TSEC_ENET /* tsec ethernet support */ #define CONFIG_ENV_OVERWRITE #undef CONFIG_SPD_EEPROM /* do not use SPD EEPROM for DDR setup*/ -#define CONFIG_DDR_ECC /* only for ECC DDR module */ #define CONFIG_DDR_DLL /* possible DLL fix needed */ #define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */ +#define CONFIG_DDR_ECC /* only for ECC DDR module */ +#define CONFIG_MEM_INIT_VALUE 0xDeadBeef + /* * sysclk for MPC85xx @@ -250,17 +252,21 @@ #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_MPC85XX_TSEC1 1 +#define CONFIG_MPC85XX_TSEC1_NAME "TSEC0" #define CONFIG_MPC85XX_TSEC2 1 +#define CONFIG_MPC85XX_TSEC2_NAME "TSEC1" #define TSEC1_PHY_ADDR 2 #define TSEC2_PHY_ADDR 3 #define TSEC1_PHYIDX 0 #define TSEC2_PHYIDX 0 #define CONFIG_MPC85XX_FEC 1 +#define CONFIG_MPC85XX_FEC_NAME "FEC" #define FEC_PHY_ADDR 1 #define FEC_PHYIDX 0 -#define CONFIG_ETHPRIME "MOTO ENET0" +/* Options are: TSEC[0-1] */ +#define CONFIG_ETHPRIME "TSEC0" #define CONFIG_HAS_ETH1 1 #define CONFIG_HAS_ETH2 1 diff --git a/include/configs/SBC8540.h b/include/configs/SBC8540.h index 5bdabfee9a..0451b20819 100644 --- a/include/configs/SBC8540.h +++ b/include/configs/SBC8540.h @@ -227,10 +227,14 @@ #if defined(CONFIG_TSEC_ENET) /* TSEC Ethernet port */ - #define CONFIG_NET_MULTI 1 - #define CONFIG_PHY_BCM5421S /* GigaBit Ether PHY */ - #define CONFIG_MII 1 /* MII PHY management */ - #define CONFIG_PHY_ADDR 25 /* PHY address */ +# define CONFIG_NET_MULTI 1 +# define CONFIG_MPC85xx_TSEC1 +# define CONFIG_MPC85xx_TSEC1_NAME "TSEC0" +# define CONFIG_MII 1 /* MII PHY management */ +# define TSEC1_PHY_ADDR 25 +# define TSEC1_PHYIDX 0 +/* Options are: TSEC0 */ +# define CONFIG_ETHPRIME "TSEC0" #elif defined(CONFIG_ETHER_ON_FCC) /* CPM FCC Ethernet */ diff --git a/include/configs/SBC8560.h b/include/configs/SBC8560.h index ca7e5dd9d9..8b46a17ed5 100644 --- a/include/configs/SBC8560.h +++ b/include/configs/SBC8560.h @@ -215,10 +215,14 @@ #if defined(CONFIG_TSEC_ENET) /* TSEC Ethernet port */ - #define CONFIG_NET_MULTI 1 - #define CONFIG_PHY_BCM5421S /* GigaBit Ether PHY */ - #define CONFIG_MII 1 /* MII PHY management */ - #define CONFIG_PHY_ADDR 25 /* PHY address */ +# define CONFIG_NET_MULTI 1 +# define CONFIG_MII 1 /* MII PHY management */ +# define CONFIG_MPC85xx_TSEC1 +# define CONFIG_MPC85xx_TSEC1_NAME "TSEC0" +# define TSEC1_PHY_ADDR 25 +# define TSEC1_PHYIDX 0 +/* Options are: TSEC0 */ +# define CONFIG_ETHPRIME "TSEC0" #elif defined(CONFIG_ETHER_ON_FCC) /* CPM FCC Ethernet */ diff --git a/include/configs/TQM8540.h b/include/configs/TQM8540.h index 9dc77c4bd2..8438b9325b 100644 --- a/include/configs/TQM8540.h +++ b/include/configs/TQM8540.h @@ -280,20 +280,24 @@ #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_MPC85XX_TSEC1 1 +#define CONFIG_MPC85XX_TSEC1_NAME "TSEC0" #define CONFIG_MPC85XX_TSEC2 1 +#define CONFIG_MPC85XX_TSEC2_NAME "TSEC1" #define TSEC1_PHY_ADDR 0 #define TSEC2_PHY_ADDR 1 #define TSEC1_PHYIDX 0 #define TSEC2_PHYIDX 0 #define CONFIG_MPC85XX_FEC 1 +#define CONFIG_MPC85XX_FEC_NAME "FEC" #define FEC_PHY_ADDR 2 #define FEC_PHYIDX 0 #define CONFIG_HAS_ETH1 #define CONFIG_HAS_ETH2 -#define CONFIG_ETHPRIME "ENET1" +/* Options are TSEC[0-1], FEC */ +#define CONFIG_ETHPRIME "TSEC1" #endif /* CONFIG_TSEC_ENET */ diff --git a/include/configs/TQM8560.h b/include/configs/TQM8560.h index f418e26344..1466f31780 100644 --- a/include/configs/TQM8560.h +++ b/include/configs/TQM8560.h @@ -276,6 +276,7 @@ #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_MPC85XX_TSEC2 1 +#define CONFIG_MPC85XX_TSEC2_NAME "TSEC1" #define TSEC2_PHY_ADDR 1 #define TSEC2_PHYIDX 0 @@ -288,7 +289,7 @@ #define CFG_CPMFCR_RAMTYPE 0 #define CFG_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB) -#define CONFIG_ETHPRIME "ENET1" +#define CONFIG_ETHPRIME "TSEC1" /* * Environment diff --git a/include/configs/sbc8560.h b/include/configs/sbc8560.h index 72a3091d5f..5a434dc767 100644 --- a/include/configs/sbc8560.h +++ b/include/configs/sbc8560.h @@ -210,10 +210,14 @@ #if defined(CONFIG_TSEC_ENET) /* TSEC Ethernet port */ - #define CONFIG_NET_MULTI 1 - #define CONFIG_PHY_BCM5421S 1 /* GigaBit Ether PHY */ - #define CONFIG_MII 1 /* MII PHY management */ - #define CONFIG_PHY_ADDR 25 /* PHY address */ +# define CONFIG_NET_MULTI 1 +# define CONFIG_MII 1 /* MII PHY management */ +# define CONFIG_MPC85xx_TSEC1 +# define CONFIG_MPC85xx_TSEC1_NAME "TSEC0" +# define TSEC1_PHY_ADDR 25 +# define TSEC1_PHYIDX 0 +/* Options are: TSEC0 */ +# define CONFIG_ETHPRIME "TSEC0" #elif defined(CONFIG_ETHER_ON_FCC) /* CPM FCC Ethernet */ diff --git a/include/configs/stxgp3.h b/include/configs/stxgp3.h index b5684d334b..e218597db0 100644 --- a/include/configs/stxgp3.h +++ b/include/configs/stxgp3.h @@ -227,14 +227,16 @@ #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_MPC85XX_TSEC1 1 +#define CONFIG_MPC85XX_TSEC1_NAME "TSEC0" #define CONFIG_MPC85XX_TSEC2 1 +#define CONFIG_MPC85XX_TSEC2_NAME "TSEC1" #undef CONFIG_MPS85XX_FEC #define TSEC1_PHY_ADDR 2 #define TSEC2_PHY_ADDR 4 #define TSEC1_PHYIDX 0 #define TSEC2_PHYIDX 0 -#define CONFIG_ETHPRIME "MOTO ENET0" +#define CONFIG_ETHPRIME "TSEC0" #elif defined(CONFIG_ETHER_ON_FCC) /* CPM FCC Ethernet */ diff --git a/include/spd.h b/include/spd.h index 1ad4d801f5..acbc1e1e3d 100644 --- a/include/spd.h +++ b/include/spd.h @@ -25,54 +25,84 @@ #define _SPD_H_ typedef struct spd_eeprom_s { - unsigned char info_size; /* # of bytes written into serial memory */ - unsigned char chip_size; /* Total # of bytes of SPD memory device */ - unsigned char mem_type; /* Fundamental memory type (FPM, EDO, SDRAM...) */ - unsigned char nrow_addr; /* # of Row Addresses on this assembly */ - unsigned char ncol_addr; /* # of Column Addresses on this assembly */ - unsigned char nrows; /* # of Module Rows on this assembly */ - unsigned char dataw_lsb; /* Data Width of this assembly */ - unsigned char dataw_msb; /* ... Data Width continuation */ - unsigned char voltage; /* Voltage interface standard of this assembly */ - unsigned char clk_cycle; /* SDRAM Cycle time at CL=X */ - unsigned char clk_access; /* SDRAM Access from Clock at CL=X */ - unsigned char config; /* DIMM Configuration type (non-parity, ECC) */ - unsigned char refresh; /* Refresh Rate/Type */ - unsigned char primw; /* Primary SDRAM Width */ - unsigned char ecw; /* Error Checking SDRAM width */ - unsigned char min_delay; /* Min Clock Delay for Back to Back Random Address */ - unsigned char burstl; /* Burst Lengths Supported */ - unsigned char nbanks; /* # of Banks on Each SDRAM Device */ - unsigned char cas_lat; /* CAS# Latencies Supported */ - unsigned char cs_lat; /* CS# Latency */ - unsigned char write_lat; /* Write Latency (also called Write Recovery time) */ - unsigned char mod_attr; /* SDRAM Module Attributes */ - unsigned char dev_attr; /* SDRAM Device Attributes */ - unsigned char clk_cycle2; /* Min SDRAM Cycle time at CL=X-1 */ - unsigned char clk_access2; /* SDRAM Access from Clock at CL=X-1 */ - unsigned char clk_cycle3; /* Min SDRAM Cycle time at CL=X-2 */ - unsigned char clk_access3; /* Max SDRAM Access from Clock at CL=X-2 */ - unsigned char trp; /* Min Row Precharge Time (tRP) */ - unsigned char trrd; /* Min Row Active to Row Active (tRRD) */ - unsigned char trcd; /* Min RAS to CAS Delay (tRCD) */ - unsigned char tras; /* Minimum RAS Pulse Width (tRAS) */ - unsigned char row_dens; /* Density of each row on module */ - unsigned char ca_setup; /* Command and Address signal input setup time */ - unsigned char ca_hold; /* Command and Address signal input hold time */ - unsigned char data_setup; /* Data signal input setup time */ - unsigned char data_hold; /* Data signal input hold time */ - unsigned char sset[26]; /* Superset Information (may be used in future) */ - unsigned char spd_rev; /* SPD Data Revision Code */ - unsigned char cksum; /* Checksum for bytes 0-62 */ - unsigned char mid[8]; /* Manufacturer's JEDEC ID code per JEP-108E */ - unsigned char mloc; /* Manufacturing Location */ - unsigned char mpart[18]; /* Manufacturer's Part Number */ - unsigned char rev[2]; /* Revision Code */ - unsigned char mdate[2]; /* Manufacturing Date */ - unsigned char sernum[4]; /* Assembly Serial Number */ - unsigned char mspec[27]; /* Manufacturer Specific Data */ - unsigned char freq; /* Intel specification frequency */ - unsigned char intel_cas; /* Intel Specification CAS# Latency support */ + unsigned char info_size; /* 0 # bytes written into serial memory */ + unsigned char chip_size; /* 1 Total # bytes of SPD memory device */ + unsigned char mem_type; /* 2 Fundamental memory type */ + unsigned char nrow_addr; /* 3 # of Row Addresses on this assembly */ + unsigned char ncol_addr; /* 4 # of Column Addrs on this assembly */ + unsigned char nrows; /* 5 # of Module Rows on this assembly */ + unsigned char dataw_lsb; /* 6 Data Width of this assembly */ + unsigned char dataw_msb; /* 7 ... Data Width continuation */ + unsigned char voltage; /* 8 Voltage intf std of this assembly */ + unsigned char clk_cycle; /* 9 SDRAM Cycle time at CL=X */ + unsigned char clk_access; /* 10 SDRAM Access from Clock at CL=X */ + unsigned char config; /* 11 DIMM Configuration type */ + unsigned char refresh; /* 12 Refresh Rate/Type */ + unsigned char primw; /* 13 Primary SDRAM Width */ + unsigned char ecw; /* 14 Error Checking SDRAM width */ + unsigned char min_delay; /* 15 for Back to Back Random Address */ + unsigned char burstl; /* 16 Burst Lengths Supported */ + unsigned char nbanks; /* 17 # of Banks on Each SDRAM Device */ + unsigned char cas_lat; /* 18 CAS# Latencies Supported */ + unsigned char cs_lat; /* 19 CS# Latency */ + unsigned char write_lat; /* 20 Write Latency (aka Write Recovery) */ + unsigned char mod_attr; /* 21 SDRAM Module Attributes */ + unsigned char dev_attr; /* 22 SDRAM Device Attributes */ + unsigned char clk_cycle2; /* 23 Min SDRAM Cycle time at CL=X-1 */ + unsigned char clk_access2; /* 24 SDRAM Access from Clock at CL=X-1 */ + unsigned char clk_cycle3; /* 25 Min SDRAM Cycle time at CL=X-2 */ + unsigned char clk_access3; /* 26 Max Access from Clock at CL=X-2 */ + unsigned char trp; /* 27 Min Row Precharge Time (tRP)*/ + unsigned char trrd; /* 28 Min Row Active to Row Active (tRRD) */ + unsigned char trcd; /* 29 Min RAS to CAS Delay (tRCD) */ + unsigned char tras; /* 30 Minimum RAS Pulse Width (tRAS) */ + unsigned char row_dens; /* 31 Density of each row on module */ + unsigned char ca_setup; /* 32 Cmd + Addr signal input setup time */ + unsigned char ca_hold; /* 33 Cmd and Addr signal input hold time */ + unsigned char data_setup; /* 34 Data signal input setup time */ + unsigned char data_hold; /* 35 Data signal input hold time */ + unsigned char twr; /* 36 Write Recovery time tWR */ + unsigned char twtr; /* 37 Int write to read delay tWTR */ + unsigned char trtp; /* 38 Int read to precharge delay tRTP */ + unsigned char mem_probe; /* 39 Mem analysis probe characteristics */ + unsigned char trctrfc_ext; /* 40 Extensions to trc and trfc */ + unsigned char trc; /* 41 Min Active to Auto refresh time tRC */ + unsigned char trfc; /* 42 Min Auto to Active period tRFC */ + unsigned char tckmax; /* 43 Max device cycle time tCKmax */ + unsigned char tdqsq; /* 44 Max DQS to DQ skew */ + unsigned char tqhs; /* 45 Max Read DataHold skew tQHS */ + unsigned char pll_relock; /* 46 PLL Relock time */ + unsigned char res[15]; /* 47-xx IDD in SPD and Reserved space */ + unsigned char spd_rev; /* 62 SPD Data Revision Code */ + unsigned char cksum; /* 63 Checksum for bytes 0-62 */ + unsigned char mid[8]; /* 64 Mfr's JEDEC ID code per JEP-108E */ + unsigned char mloc; /* 72 Manufacturing Location */ + unsigned char mpart[18]; /* 73 Manufacturer's Part Number */ + unsigned char rev[2]; /* 91 Revision Code */ + unsigned char mdate[2]; /* 93 Manufacturing Date */ + unsigned char sernum[4]; /* 95 Assembly Serial Number */ + unsigned char mspec[27]; /* 99 Manufacturer Specific Data */ + + /* + * Open for Customer Use starting with byte 128. + */ + unsigned char freq; /* 128 Intel spec: frequency */ + unsigned char intel_cas; /* 129 Intel spec: CAS# Latency support */ } spd_eeprom_t; + +/* + * Byte 2 Fundamental Memory Types. + */ +#define SPD_MEMTYPE_FPM (0x01) +#define SPD_MEMTYPE_EDO (0x02) +#define SPD_MEMTYPE_PIPE_NIBBLE (0x03) +#define SPD_MEMTYPE_SDRAM (0x04) +#define SPD_MEMTYPE_ROM (0x05) +#define SPD_MEMTYPE_SGRAM (0x06) +#define SPD_MEMTYPE_DDR (0x07) +#define SPD_MEMTYPE_DDR2 (0x08) + + #endif /* _SPD_H_ */ + diff --git a/net/eth.c b/net/eth.c index 29c24c8827..e7e11f9d6c 100644 --- a/net/eth.c +++ b/net/eth.c @@ -52,7 +52,7 @@ extern int rtl8139_initialize(bd_t*); extern int rtl8169_initialize(bd_t*); extern int scc_initialize(bd_t*); extern int skge_initialize(bd_t*); -extern int tsec_initialize(bd_t*, int); +extern int tsec_initialize(bd_t*, int, char *); static struct eth_device *eth_devices, *eth_current; @@ -155,13 +155,20 @@ int eth_initialize(bd_t *bis) skge_initialize(bis); #endif #if defined(CONFIG_MPC85XX_TSEC1) - tsec_initialize(bis, 0); + tsec_initialize(bis, 0, CONFIG_MPC85XX_TSEC1_NAME); #endif #if defined(CONFIG_MPC85XX_TSEC2) - tsec_initialize(bis, 1); + tsec_initialize(bis, 1, CONFIG_MPC85XX_TSEC2_NAME); #endif #if defined(CONFIG_MPC85XX_FEC) - tsec_initialize(bis, 2); + tsec_initialize(bis, 2, CONFIG_MPC85XX_FEC_NAME); +#else +# if defined(CONFIG_MPC85XX_TSEC3) + tsec_initialize(bis, 2, CONFIG_MPC85XX_TSEC3_NAME); +# endif +# if defined(CONFIG_MPC85XX_TSEC4) + tsec_initialize(bis, 3, CONFIG_MPC85XX_TSEC4_NAME); +# endif #endif #if defined(CONFIG_AU1X00) au1x00_enet_initialize(bis); -- 2.30.2