From d522ccecb28f941aadcaf7a50cd6daa861f468a7 Mon Sep 17 00:00:00 2001 From: Patryk Kowalczyk Date: Sat, 16 Sep 2023 03:02:35 +0200 Subject: [PATCH] filogic: add support for ASUS TUF AX6000 Hardware ======== SOC: MediaTek MT7986 RAM: 512MB DDR3 FLASH: 256MB SPI-NAND WIFI: Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz 4T4R ETH: MediaTek MT7530 Switch (LAN) MaxLinear GPY211C 2.5 N-Base-T PHY (WAN) MaxLinear GPY211C 2.5 N-Base-T PHY (LAN) UART: 3V3 115200 8N1 (Do not connect VCC) USB 3.1 Installation ============ Download the OpenWrt initramfs image. Copy the image to a TFTP server reachable at 192.168.1.70/24. Rename the image to TUF-AX6000.bin. Connect to the serial console, interrupt the auto boot process by pressing '4' when prompted or press '1' and set client IP, server IP and name of the image. yOU don't need to open the case or even soldering anything. use three goldpin wires, remove their plastic cover and connect them to the console pinout via the case holes. You can see three holes From Bottom: RX, TX, Ground - partially covered Download & Boot the OpenWrt initramfs image. In case of option '4' $ setenv ipaddr 192.168.1.1 $ setenv serverip 192.168.1.70 $ tftpboot 0x46000000 TUF-AX6000.bin $ bootm 0x46000000 In case of option '1' 1: Load System code to SDRAM via TFTP. Please Input new ones /or Ctrl-C to discard Input device IP (192.168.1.1) ==: Input server IP (192.168.1.70) ==: Input Linux Kernel filename (TUF-AX6000.trx) ==: Wait for OpenWrt to boot. Transfer the sysupgrade image to the device using scp and install using sysupgrade. $ sysupgrade -n Missing features ================ 2.5Gb LAN port LED is ON during boot or when the LAN cable is disconnected The cover yellow light is not supported. (only blue one) Signed-off-by: Patryk Kowalczyk --- .../mediatek/dts/mt7986a-asus-tuf-ax6000.dts | 382 ++++++++++++++++++ .../filogic/base-files/etc/board.d/02_network | 6 +- .../etc/hotplug.d/firmware/11-mt76-caldata | 3 +- .../etc/hotplug.d/ieee80211/11_fix_wifi_mac | 3 +- .../base-files/lib/preinit/10_fix_eth_mac.sh | 3 +- .../base-files/lib/upgrade/platform.sh | 3 +- target/linux/mediatek/image/filogic.mk | 16 + 7 files changed, 411 insertions(+), 5 deletions(-) create mode 100644 target/linux/mediatek/dts/mt7986a-asus-tuf-ax6000.dts diff --git a/target/linux/mediatek/dts/mt7986a-asus-tuf-ax6000.dts b/target/linux/mediatek/dts/mt7986a-asus-tuf-ax6000.dts new file mode 100644 index 0000000000..2e9114f99c --- /dev/null +++ b/target/linux/mediatek/dts/mt7986a-asus-tuf-ax6000.dts @@ -0,0 +1,382 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) + +/dts-v1/; +#include +#include +#include + +#include "mt7986a.dtsi" + +/ { + model = "ASUS TUF-AX6000"; + compatible = "asus,tuf-ax6000", "mediatek,mt7986a"; + + aliases { + serial0 = &uart0; + led-boot = &led_system; + led-failsafe = &led_system; + led-running = &led_system; + led-upgrade = &led_system; + }; + + chosen { + stdout-path = "serial0:115200n8"; + bootargs-override = "ubi.mtd=UBI_DEV"; + }; + + memory { + reg = <0 0x40000000 0 0x20000000>; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&pio 9 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + mesh { + label = "wps"; + gpios = <&pio 10 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + + wlan { + label = "white:wlan"; + gpios = <&pio 2 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "phy1tpt"; + }; + + led_system: system { + label = "white:system"; + gpios = <&pio 11 GPIO_ACTIVE_HIGH>; + }; + + wan-red { + label = "red:wan"; + gpios = <&pio 12 GPIO_ACTIVE_LOW>; + }; + + cover-blue { + label = "blue:cover"; + gpios = <&pio 20 GPIO_ACTIVE_HIGH>; + }; + }; + + reg_3p3v: regulator-3p3v { + compatible = "regulator-fixed"; + regulator-name = "fixed-3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_5v: regulator-5v { + compatible = "regulator-fixed"; + regulator-name = "fixed-5V"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + regulator-always-on; + }; +}; + +&crypto { + status = "okay"; +}; + +ð { + status = "okay"; + + gmac0: mac@0 { + /* LAN */ + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-mode = "2500base-x"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + + gmac1: mac@1 { + /* WAN */ + compatible = "mediatek,eth-mac"; + reg = <1>; + phy-mode = "2500base-x"; + phy-handle = <&phy6>; + }; + + mdio: mdio-bus { + #address-cells = <1>; + #size-cells = <0>; + }; +}; + +&mdio { + reset-gpios = <&pio 6 GPIO_ACTIVE_LOW>; + reset-delay-us = <50000>; + reset-post-delay-us = <20000>; + + phy5: phy@5 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <5>; + + mxl,led-config = <0x03f0 0x0 0x0 0x0>; + }; + + phy6: phy@6 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <6>; + + /* LED0: CONN (WAN white) */ + mxl,led-config = <0x03f0 0x0 0x0 0x0>; + }; + + switch: switch@0 { + compatible = "mediatek,mt7531"; + reg = <31>; + + reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>; + reset-assert-us = <10000>; + reset-deassert-us = <10000>; + }; +}; + +&pio { + spi_flash_pins: spi-flash-pins-33-to-38 { + mux { + function = "spi"; + groups = "spi0", "spi0_wp_hold"; + }; + conf-pu { + pins = "SPI2_CS", "SPI2_HOLD", "SPI2_WP"; + drive-strength = <8>; + mediatek,pull-up-adv = <0>; /* bias-disable */ + }; + conf-pd { + pins = "SPI2_CLK", "SPI2_MOSI", "SPI2_MISO"; + drive-strength = <8>; + mediatek,pull-down-adv = <0>; /* bias-disable */ + }; + }; + + wf_2g_5g_pins: wf_2g_5g-pins { + mux { + function = "wifi"; + groups = "wf_2g", "wf_5g"; + }; + conf { + pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4", + "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6", + "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10", + "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1", + "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0", + "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8", + "WF1_TOP_CLK", "WF1_TOP_DATA"; + drive-strength = <4>; + }; + }; + + wf_dbdc_pins: wf-dbdc-pins { + mux { + function = "wifi"; + groups = "wf_dbdc"; + }; + conf { + pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4", + "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6", + "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10", + "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1", + "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0", + "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8", + "WF1_TOP_CLK", "WF1_TOP_DATA"; + drive-strength = <4>; + }; + }; +}; + +&pcie_phy { + status = "okay"; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi_flash_pins>; + status = "okay"; + + spi_nand_flash: flash@0 { + compatible = "spi-nand"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0>; + + spi-max-frequency = <20000000>; + spi-tx-bus-width = <4>; + spi-rx-bus-width = <4>; + + partitions: partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "bootloader"; + reg = <0x0 0x400000>; + read-only; + }; + + partition@400000 { + label = "UBI_DEV"; + reg = <0x400000 0xfc00000>; + }; + }; + }; +}; + +&switch { + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + reg = <4>; + label = "lan1"; + }; + + port@2 { + reg = <3>; + label = "lan2"; + }; + + port@3 { + reg = <2>; + label = "lan3"; + }; + + port@4 { + reg = <1>; + label = "lan4"; + }; + + port@5 { + reg = <5>; + label = "lan5"; + phy-mode = "2500base-x"; + phy-handle = <&phy5>; + + }; + + port@6 { + reg = <6>; + label = "cpu"; + ethernet = <&gmac0>; + phy-mode = "2500base-x"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy@1 { + reg = <1>; + + mediatek,led-config = < + 0x21 0x8009 /* BASIC_CTRL */ + 0x22 0x0c00 /* ON_DURATION */ + 0x23 0x1400 /* BLINK_DURATION */ + 0x24 0x8000 /* LED0_ON_CTRL */ + 0x25 0x0000 /* LED0_BLINK_CTRL */ + 0x26 0xc007 /* LED1_ON_CTRL */ + 0x27 0x003f /* LED1_BLINK_CTRL */ + >; + }; + + phy@2 { + reg = <2>; + + mediatek,led-config = < + 0x21 0x8009 /* BASIC_CTRL */ + 0x22 0x0c00 /* ON_DURATION */ + 0x23 0x1400 /* BLINK_DURATION */ + 0x24 0x8000 /* LED0_ON_CTRL */ + 0x25 0x0000 /* LED0_BLINK_CTRL */ + 0x26 0xc007 /* LED1_ON_CTRL */ + 0x27 0x003f /* LED1_BLINK_CTRL */ + >; + }; + + phy@3 { + reg = <3>; + + mediatek,led-config = < + 0x21 0x8009 /* BASIC_CTRL */ + 0x22 0x0c00 /* ON_DURATION */ + 0x23 0x1400 /* BLINK_DURATION */ + 0x24 0x8000 /* LED0_ON_CTRL */ + 0x25 0x0000 /* LED0_BLINK_CTRL */ + 0x26 0xc007 /* LED1_ON_CTRL */ + 0x27 0x003f /* LED1_BLINK_CTRL */ + >; + }; + + phy@4 { + reg = <4>; + + mediatek,led-config = < + 0x21 0x8009 /* BASIC_CTRL */ + 0x22 0x0c00 /* ON_DURATION */ + 0x23 0x1400 /* BLINK_DURATION */ + 0x24 0x8000 /* LED0_ON_CTRL */ + 0x25 0x0000 /* LED0_BLINK_CTRL */ + 0x26 0xc007 /* LED1_ON_CTRL */ + 0x27 0x003f /* LED1_BLINK_CTRL */ + >; + }; + }; +}; + +&watchdog { + status = "okay"; +}; + +&wifi { + status = "okay"; + pinctrl-names = "default", "dbdc"; + pinctrl-0 = <&wf_2g_5g_pins>; + pinctrl-1 = <&wf_dbdc_pins>; +}; + +&trng { + status = "okay"; +}; + +&uart0 { + status = "okay"; +}; + +&ssusb { + vusb33-supply = <®_3p3v>; + vbus-supply = <®_5v>; + status = "okay"; +}; + +&usb_phy { + status = "okay"; +}; \ No newline at end of file diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network index d9fa477353..aad1d67ff6 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network @@ -15,6 +15,9 @@ mediatek_setup_interfaces() mediatek,mt7981-rfb) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" eth1 ;; + asus,tuf-ax6000) + ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 lan5" eth1 + ;; netgear,wax220|\ ubnt,unifi-6-plus|\ zyxel,nwa50ax-pro) @@ -78,7 +81,8 @@ mediatek_setup_macs() local label_mac="" case $board in - asus,tuf-ax4200) + asus,tuf-ax4200|\ + asus,tuf-ax6000) CI_UBIPART="UBI_DEV" addr=$(mtd_get_mac_binary_ubi "Factory" 0x4) wan_mac="${addr}" diff --git a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/firmware/11-mt76-caldata b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/firmware/11-mt76-caldata index e782637348..63c1ec31b7 100644 --- a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/firmware/11-mt76-caldata +++ b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/firmware/11-mt76-caldata @@ -45,7 +45,8 @@ case "$FIRMWARE" in ;; "mediatek/mt7986_eeprom_mt7976_dbdc.bin") case "$board" in - asus,tuf-ax4200) + asus,tuf-ax4200|\ + asus,tuf-ax6000) CI_UBIPART="UBI_DEV" caldata_extract_ubi "Factory" 0x0 0x1000 ;; diff --git a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac index 5de4061c94..395cc0f2dc 100644 --- a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac +++ b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac @@ -16,7 +16,8 @@ case "$board" in [ "$PHYNBR" = "1" ] && cat $key_path/6gMAC > /sys${DEVPATH}/macaddress [ "$PHYNBR" = "2" ] && cat $key_path/5gMAC > /sys${DEVPATH}/macaddress ;; - asus,tuf-ax4200) + asus,tuf-ax4200|\ + asus,tuf-ax6000) CI_UBIPART="UBI_DEV" addr=$(mtd_get_mac_binary_ubi "Factory" 0x4) # Originally, phy0 is phy1 mac with LA bit set. However, this would conflict diff --git a/target/linux/mediatek/filogic/base-files/lib/preinit/10_fix_eth_mac.sh b/target/linux/mediatek/filogic/base-files/lib/preinit/10_fix_eth_mac.sh index 69d0ab6c60..d770b13643 100644 --- a/target/linux/mediatek/filogic/base-files/lib/preinit/10_fix_eth_mac.sh +++ b/target/linux/mediatek/filogic/base-files/lib/preinit/10_fix_eth_mac.sh @@ -10,7 +10,8 @@ preinit_set_mac_address() { ip link set dev game address "$(cat $key_path/LANMAC)" ip link set dev eth1 address "$(cat $key_path/WANMAC)" ;; - asus,tuf-ax4200) + asus,tuf-ax4200|\ + asus,tuf-ax6000) CI_UBIPART="UBI_DEV" addr=$(mtd_get_mac_binary_ubi "Factory" 0x4) ip link set dev eth0 address "$addr" diff --git a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh index c8eea2eca2..b7b9d65993 100755 --- a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh +++ b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh @@ -56,7 +56,8 @@ platform_do_upgrade() { CI_ROOTPART="rootfs" emmc_do_upgrade "$1" ;; - asus,tuf-ax4200) + asus,tuf-ax4200|\ + asus,tuf-ax6000) CI_UBIPART="UBI_DEV" CI_KERNPART="linux" nand_do_upgrade "$1" diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk index f7b838cf3b..e501ac3c74 100644 --- a/target/linux/mediatek/image/filogic.mk +++ b/target/linux/mediatek/image/filogic.mk @@ -121,6 +121,22 @@ define Device/asus_tuf-ax4200 endef TARGET_DEVICES += asus_tuf-ax4200 +define Device/asus_tuf-ax6000 + DEVICE_VENDOR := ASUS + DEVICE_MODEL := TUF-AX6000 + DEVICE_DTS := mt7986a-asus-tuf-ax6000 + DEVICE_DTS_DIR := ../dts + DEVICE_DTS_LOADADDR := 0x47000000 + DEVICE_PACKAGES := kmod-usb3 kmod-mt7986-firmware mt7986-wo-firmware + IMAGES := sysupgrade.bin + KERNEL := kernel-bin | lzma | \ + fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb + KERNEL_INITRAMFS := kernel-bin | lzma | \ + fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k + IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata +endef +TARGET_DEVICES += asus_tuf-ax6000 + define Device/acer_predator-w6 DEVICE_VENDOR := Acer DEVICE_MODEL := Predator W6 -- 2.30.2