From d31a7b51abc91241870e907ff76ce7058aceefa1 Mon Sep 17 00:00:00 2001 From: Gabor Juhos Date: Fri, 22 May 2009 08:38:10 +0000 Subject: [PATCH] add experimental support for 2.6.30 SVN-Revision: 15979 --- .../adm5120/patches-2.6.30/001-adm5120.patch | 56 +++ .../patches-2.6.30/002-adm5120_flash.patch | 21 + .../patches-2.6.30/003-adm5120_switch.patch | 23 ++ .../patches-2.6.30/005-adm5120_usb.patch | 33 ++ .../patches-2.6.30/007-adm5120_pci.patch | 19 + .../009-adm5120_leds_switch_trigger.patch | 22 + .../101-cfi_fixup_macronix_bootloc.patch | 84 ++++ .../102-jedec_pmc_39lvxxx_chips.patch | 68 ++++ .../patches-2.6.30/103-mtd_trxsplit.patch | 24 ++ .../patches-2.6.30/120-rb153_cf_driver.patch | 28 ++ .../patches-2.6.30/140-cmdline_hack.patch | 15 + .../patches-2.6.30/200-amba_pl010_hacks.patch | 378 ++++++++++++++++++ .../patches-2.6.30/201-amba_bus_hacks.patch | 13 + .../202-pci_disable_common_quirks.patch | 191 +++++++++ .../203-gpio_leds_brightness.patch | 27 ++ .../patches-2.6.30/310-adm5120_wdt.patch | 31 ++ .../800-adm5120-remove-amba-bus-id.patch | 18 + .../801-adm5120-flash-remove-bus-id.patch | 11 + ...itch-remove-redundant-napi-functions.patch | 20 + target/linux/adm5120/router_be/config-2.6.30 | 216 ++++++++++ target/linux/adm5120/router_le/config-2.6.30 | 263 ++++++++++++ 21 files changed, 1561 insertions(+) create mode 100644 target/linux/adm5120/patches-2.6.30/001-adm5120.patch create mode 100644 target/linux/adm5120/patches-2.6.30/002-adm5120_flash.patch create mode 100644 target/linux/adm5120/patches-2.6.30/003-adm5120_switch.patch create mode 100644 target/linux/adm5120/patches-2.6.30/005-adm5120_usb.patch create mode 100644 target/linux/adm5120/patches-2.6.30/007-adm5120_pci.patch create mode 100644 target/linux/adm5120/patches-2.6.30/009-adm5120_leds_switch_trigger.patch create mode 100644 target/linux/adm5120/patches-2.6.30/101-cfi_fixup_macronix_bootloc.patch create mode 100644 target/linux/adm5120/patches-2.6.30/102-jedec_pmc_39lvxxx_chips.patch create mode 100644 target/linux/adm5120/patches-2.6.30/103-mtd_trxsplit.patch create mode 100644 target/linux/adm5120/patches-2.6.30/120-rb153_cf_driver.patch create mode 100644 target/linux/adm5120/patches-2.6.30/140-cmdline_hack.patch create mode 100644 target/linux/adm5120/patches-2.6.30/200-amba_pl010_hacks.patch create mode 100644 target/linux/adm5120/patches-2.6.30/201-amba_bus_hacks.patch create mode 100644 target/linux/adm5120/patches-2.6.30/202-pci_disable_common_quirks.patch create mode 100644 target/linux/adm5120/patches-2.6.30/203-gpio_leds_brightness.patch create mode 100644 target/linux/adm5120/patches-2.6.30/310-adm5120_wdt.patch create mode 100644 target/linux/adm5120/patches-2.6.30/800-adm5120-remove-amba-bus-id.patch create mode 100644 target/linux/adm5120/patches-2.6.30/801-adm5120-flash-remove-bus-id.patch create mode 100644 target/linux/adm5120/patches-2.6.30/802-adm5120-switch-remove-redundant-napi-functions.patch create mode 100644 target/linux/adm5120/router_be/config-2.6.30 create mode 100644 target/linux/adm5120/router_le/config-2.6.30 diff --git a/target/linux/adm5120/patches-2.6.30/001-adm5120.patch b/target/linux/adm5120/patches-2.6.30/001-adm5120.patch new file mode 100644 index 0000000000..6b59bc7112 --- /dev/null +++ b/target/linux/adm5120/patches-2.6.30/001-adm5120.patch @@ -0,0 +1,56 @@ +--- a/arch/mips/Kconfig ++++ b/arch/mips/Kconfig +@@ -19,6 +19,21 @@ choice + prompt "System type" + default SGI_IP22 + ++config ADM5120 ++ bool "Infineon/ADMtek ADM5120 SoC based machines" ++ select CEVT_R4K ++ select CSRC_R4K ++ select SYS_HAS_CPU_MIPS32_R1 ++ select SYS_HAS_EARLY_PRINTK ++ select DMA_NONCOHERENT ++ select IRQ_CPU ++ select SYS_SUPPORTS_LITTLE_ENDIAN ++ select SYS_SUPPORTS_BIG_ENDIAN ++ select SYS_SUPPORTS_32BIT_KERNEL ++ select ARCH_REQUIRE_GPIOLIB ++ select SWAP_IO_SPACE if CPU_BIG_ENDIAN ++ select MIPS_MACHINE ++ + config MACH_ALCHEMY + bool "Alchemy processor based machines" + +@@ -632,6 +647,7 @@ config CAVIUM_OCTEON_REFERENCE_BOARD + + endchoice + ++source "arch/mips/adm5120/Kconfig" + source "arch/mips/alchemy/Kconfig" + source "arch/mips/basler/excite/Kconfig" + source "arch/mips/jazz/Kconfig" +--- a/arch/mips/Makefile ++++ b/arch/mips/Makefile +@@ -181,6 +181,21 @@ cflags-$(CONFIG_MACH_JAZZ) += -I$(srctre + load-$(CONFIG_MACH_JAZZ) += 0xffffffff80080000 + + # ++# Infineon/ADMtek ADM5120 ++# ++libs-$(CONFIG_ADM5120) += arch/mips/adm5120/prom/ ++core-$(CONFIG_ADM5120) += arch/mips/adm5120/common/ ++core-$(CONFIG_ADM5120_OEM_CELLVISION) += arch/mips/adm5120/cellvision/ ++core-$(CONFIG_ADM5120_OEM_COMPEX) += arch/mips/adm5120/compex/ ++core-$(CONFIG_ADM5120_OEM_EDIMAX) += arch/mips/adm5120/edimax/ ++core-$(CONFIG_ADM5120_OEM_INFINEON) += arch/mips/adm5120/infineon/ ++core-$(CONFIG_ADM5120_OEM_MIKROTIK) += arch/mips/adm5120/mikrotik/ ++core-$(CONFIG_ADM5120_OEM_MOTOROLA) += arch/mips/adm5120/motorola/ ++core-$(CONFIG_ADM5120_OEM_ZYXEL) += arch/mips/adm5120/zyxel/ ++cflags-$(CONFIG_ADM5120) += -I$(srctree)/arch/mips/include/asm/mach-adm5120 ++load-$(CONFIG_ADM5120) += 0xffffffff80001000 ++ ++# + # Common Alchemy Au1x00 stuff + # + core-$(CONFIG_SOC_AU1X00) += arch/mips/alchemy/common/ diff --git a/target/linux/adm5120/patches-2.6.30/002-adm5120_flash.patch b/target/linux/adm5120/patches-2.6.30/002-adm5120_flash.patch new file mode 100644 index 0000000000..97f5b96cc2 --- /dev/null +++ b/target/linux/adm5120/patches-2.6.30/002-adm5120_flash.patch @@ -0,0 +1,21 @@ +--- a/drivers/mtd/maps/Kconfig ++++ b/drivers/mtd/maps/Kconfig +@@ -562,4 +562,8 @@ config MTD_VMU + To build this as a module select M here, the module will be called + vmu-flash. + ++config MTD_ADM5120 ++ tristate "Map driver for ADM5120 based boards" ++ depends on ADM5120 ++ + endmenu +--- a/drivers/mtd/maps/Makefile ++++ b/drivers/mtd/maps/Makefile +@@ -42,6 +42,7 @@ obj-$(CONFIG_MTD_DBOX2) += dbox2-flash. + obj-$(CONFIG_MTD_SOLUTIONENGINE)+= solutionengine.o + obj-$(CONFIG_MTD_PCI) += pci.o + obj-$(CONFIG_MTD_ALCHEMY) += alchemy-flash.o ++obj-$(CONFIG_MTD_ADM5120) += adm5120-flash.o + obj-$(CONFIG_MTD_AUTCPU12) += autcpu12-nvram.o + obj-$(CONFIG_MTD_EDB7312) += edb7312.o + obj-$(CONFIG_MTD_IMPA7) += impa7.o diff --git a/target/linux/adm5120/patches-2.6.30/003-adm5120_switch.patch b/target/linux/adm5120/patches-2.6.30/003-adm5120_switch.patch new file mode 100644 index 0000000000..771dd5f807 --- /dev/null +++ b/target/linux/adm5120/patches-2.6.30/003-adm5120_switch.patch @@ -0,0 +1,23 @@ +--- a/drivers/net/Kconfig ++++ b/drivers/net/Kconfig +@@ -612,6 +612,10 @@ config MIPS_AU1X00_ENET + If you have an Alchemy Semi AU1X00 based system + say Y. Otherwise, say N. + ++config ADM5120_ENET ++ tristate "ADM5120 Ethernet switch support" ++ depends on ADM5120 ++ + config SGI_IOC3_ETH + bool "SGI IOC3 Ethernet" + depends on PCI && SGI_IP27 +--- a/drivers/net/Makefile ++++ b/drivers/net/Makefile +@@ -195,6 +195,7 @@ obj-$(CONFIG_SC92031) += sc92031.o + # This is also a 82596 and should probably be merged + obj-$(CONFIG_LP486E) += lp486e.o + ++obj-$(CONFIG_ADM5120_ENET) += adm5120sw.o + obj-$(CONFIG_ETH16I) += eth16i.o + obj-$(CONFIG_ZORRO8390) += zorro8390.o 8390.o + obj-$(CONFIG_HPLANCE) += hplance.o 7990.o diff --git a/target/linux/adm5120/patches-2.6.30/005-adm5120_usb.patch b/target/linux/adm5120/patches-2.6.30/005-adm5120_usb.patch new file mode 100644 index 0000000000..1e4bf000ea --- /dev/null +++ b/target/linux/adm5120/patches-2.6.30/005-adm5120_usb.patch @@ -0,0 +1,33 @@ +--- a/drivers/usb/Makefile ++++ b/drivers/usb/Makefile +@@ -9,6 +9,7 @@ obj-$(CONFIG_USB) += core/ + obj-$(CONFIG_USB_MON) += mon/ + + obj-$(CONFIG_PCI) += host/ ++obj-$(CONFIG_USB_ADM5120_HCD) += host/ + obj-$(CONFIG_USB_EHCI_HCD) += host/ + obj-$(CONFIG_USB_ISP116X_HCD) += host/ + obj-$(CONFIG_USB_ISP1760_HCD) += host/ +--- a/drivers/usb/host/Kconfig ++++ b/drivers/usb/host/Kconfig +@@ -4,6 +4,10 @@ + comment "USB Host Controller Drivers" + depends on USB + ++config USB_ADM5120_HCD ++ tristate "ADM5120 HCD support (EXPERIMENTAL)" ++ depends on USB && ADM5120 && EXPERIMENTAL ++ + config USB_C67X00_HCD + tristate "Cypress C67x00 HCD support" + depends on USB +--- a/drivers/usb/host/Makefile ++++ b/drivers/usb/host/Makefile +@@ -17,6 +17,7 @@ obj-$(CONFIG_USB_WHCI_HCD) += whci/ + + obj-$(CONFIG_PCI) += pci-quirks.o + ++obj-$(CONFIG_USB_ADM5120_HCD) += adm5120-hcd.o + obj-$(CONFIG_USB_EHCI_HCD) += ehci-hcd.o + obj-$(CONFIG_USB_OXU210HP_HCD) += oxu210hp-hcd.o + obj-$(CONFIG_USB_ISP116X_HCD) += isp116x-hcd.o diff --git a/target/linux/adm5120/patches-2.6.30/007-adm5120_pci.patch b/target/linux/adm5120/patches-2.6.30/007-adm5120_pci.patch new file mode 100644 index 0000000000..7869c9782b --- /dev/null +++ b/target/linux/adm5120/patches-2.6.30/007-adm5120_pci.patch @@ -0,0 +1,19 @@ +--- a/arch/mips/pci/Makefile ++++ b/arch/mips/pci/Makefile +@@ -52,3 +52,4 @@ obj-$(CONFIG_VICTOR_MPC30X) += fixup-mpc + obj-$(CONFIG_ZAO_CAPCELLA) += fixup-capcella.o + obj-$(CONFIG_WR_PPMC) += fixup-wrppmc.o + obj-$(CONFIG_MIKROTIK_RB532) += pci-rc32434.o ops-rc32434.o fixup-rc32434.o ++obj-$(CONFIG_ADM5120) += pci-adm5120.o +--- a/include/linux/pci_ids.h ++++ b/include/linux/pci_ids.h +@@ -1764,6 +1764,9 @@ + #define PCI_VENDOR_ID_ESDGMBH 0x12fe + #define PCI_DEVICE_ID_ESDGMBH_CPCIASIO4 0x0111 + ++#define PCI_VENDOR_ID_ADMTEK 0x1317 ++#define PCI_DEVICE_ID_ADMTEK_ADM5120 0x5120 ++ + #define PCI_VENDOR_ID_SIIG 0x131f + #define PCI_SUBVENDOR_ID_SIIG 0x131f + #define PCI_DEVICE_ID_SIIG_1S_10x_550 0x1000 diff --git a/target/linux/adm5120/patches-2.6.30/009-adm5120_leds_switch_trigger.patch b/target/linux/adm5120/patches-2.6.30/009-adm5120_leds_switch_trigger.patch new file mode 100644 index 0000000000..4778deac0a --- /dev/null +++ b/target/linux/adm5120/patches-2.6.30/009-adm5120_leds_switch_trigger.patch @@ -0,0 +1,22 @@ +--- a/drivers/leds/Kconfig ++++ b/drivers/leds/Kconfig +@@ -306,4 +306,12 @@ config LEDS_TRIGGER_NETDEV + This allows LEDs to be controlled by network device activity. + If unsure, say Y. + ++config LEDS_TRIGGER_ADM5120_SWITCH ++ tristate "LED ADM5120 Switch Port Status Trigger" ++ depends on LEDS_TRIGGERS && ADM5120 ++ help ++ This allows LEDs to be controlled by the port states of ++ the ADM5120 built-in Ethernet Switch ++ If unsure, say N. ++ + endif # NEW_LEDS +--- a/drivers/leds/Makefile ++++ b/drivers/leds/Makefile +@@ -40,3 +40,4 @@ obj-$(CONFIG_LEDS_TRIGGER_GPIO) += ledt + obj-$(CONFIG_LEDS_TRIGGER_DEFAULT_ON) += ledtrig-default-on.o + obj-$(CONFIG_LEDS_TRIGGER_MORSE) += ledtrig-morse.o + obj-$(CONFIG_LEDS_TRIGGER_NETDEV) += ledtrig-netdev.o ++obj-$(CONFIG_LEDS_TRIGGER_ADM5120_SWITCH) += ledtrig-adm5120-switch.o diff --git a/target/linux/adm5120/patches-2.6.30/101-cfi_fixup_macronix_bootloc.patch b/target/linux/adm5120/patches-2.6.30/101-cfi_fixup_macronix_bootloc.patch new file mode 100644 index 0000000000..60c3ab91e7 --- /dev/null +++ b/target/linux/adm5120/patches-2.6.30/101-cfi_fixup_macronix_bootloc.patch @@ -0,0 +1,84 @@ +--- a/drivers/mtd/chips/cfi_cmdset_0002.c ++++ b/drivers/mtd/chips/cfi_cmdset_0002.c +@@ -53,6 +53,12 @@ + #define AT49BV6416 0x00d6 + #define MANUFACTURER_SAMSUNG 0x00ec + ++/* Macronix */ ++#define MX29LV160B 0x2249 /* MX29LV160 Bottom-boot chip */ ++#define MX29LV160T 0x22C4 /* MX29LV160 Top-boot chip */ ++#define MX29LV320B 0x22A8 /* MX29LV320 Bottom-boot chip */ ++#define MX29LV320T 0x22A7 /* MX29LV320 Top-boot chip */ ++ + static int cfi_amdstd_read (struct mtd_info *, loff_t, size_t, size_t *, u_char *); + static int cfi_amdstd_write_words(struct mtd_info *, loff_t, size_t, size_t *, const u_char *); + static int cfi_amdstd_write_buffers(struct mtd_info *, loff_t, size_t, size_t *, const u_char *); +@@ -293,6 +299,41 @@ static void fixup_M29W128G_write_buffer( + } + } + ++#ifdef CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC ++/* ++ * Some Macronix chips has no/bad bootblock information in the CFI table ++ */ ++static void fixup_macronix_bootloc(struct mtd_info *mtd, void* param) ++{ ++ struct map_info *map = mtd->priv; ++ struct cfi_private *cfi = map->fldrv_priv; ++ struct cfi_pri_amdstd *extp = cfi->cmdset_priv; ++ __u8 t; ++ ++ switch (cfi->id) { ++ /* TODO: put affected chip ids here */ ++ case MX29LV160B: ++ case MX29LV320B: ++ t = 2; /* Bottom boot */ ++ break; ++ case MX29LV160T: ++ case MX29LV320T: ++ t = 3; /* Top boot */ ++ break; ++ default: ++ return; ++ } ++ ++ if (extp->TopBottom == t) ++ /* boot location detected by the CFI layer is correct */ ++ return; ++ ++ extp->TopBottom = t; ++ printk("%s: Macronix chip detected, id:0x%04X, boot location forced " ++ "to %s\n", map->name, cfi->id, (t == 2) ? "bottom" : "top"); ++} ++#endif /* CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC */ ++ + static struct cfi_fixup cfi_fixup_table[] = { + { CFI_MFR_ATMEL, CFI_ID_ANY, fixup_convert_atmel_pri, NULL }, + #ifdef AMD_BOOTLOC_BUG +@@ -330,6 +371,9 @@ static struct cfi_fixup fixup_table[] = + */ + { CFI_MFR_ANY, CFI_ID_ANY, fixup_use_erase_chip, NULL }, + { CFI_MFR_ATMEL, AT49BV6416, fixup_use_atmel_lock, NULL }, ++#ifdef CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC ++ { MANUFACTURER_MACRONIX, CFI_ID_ANY, fixup_macronix_bootloc, NULL, }, ++#endif + { 0, 0, NULL, NULL } + }; + +--- a/drivers/mtd/chips/Kconfig ++++ b/drivers/mtd/chips/Kconfig +@@ -198,6 +198,14 @@ config MTD_CFI_AMDSTD + provides support for one of those command sets, used on chips + including the AMD Am29LV320. + ++config MTD_CFI_FIXUP_MACRONIX_BOOTLOC ++ bool "Fix boot-block location for Macronix flash chips" ++ depends on MTD_CFI_AMDSTD ++ help ++ Some Macronix flash chips have no/wrong boot-block location in the ++ CFI table, and the driver may detect the type incorrectly. Select ++ this if your board has such chip. ++ + config MTD_CFI_STAA + tristate "Support for ST (Advanced Architecture) flash chips" + depends on MTD_GEN_PROBE diff --git a/target/linux/adm5120/patches-2.6.30/102-jedec_pmc_39lvxxx_chips.patch b/target/linux/adm5120/patches-2.6.30/102-jedec_pmc_39lvxxx_chips.patch new file mode 100644 index 0000000000..55a201d413 --- /dev/null +++ b/target/linux/adm5120/patches-2.6.30/102-jedec_pmc_39lvxxx_chips.patch @@ -0,0 +1,68 @@ +--- a/drivers/mtd/chips/jedec_probe.c ++++ b/drivers/mtd/chips/jedec_probe.c +@@ -128,6 +128,10 @@ + #define UPD29F064115 0x221C + + /* PMC */ ++#define PM39LV512 0x001B ++#define PM39LV010 0x001C ++#define PM39LV020 0x003D ++#define PM39LV040 0x003E + #define PM49FL002 0x006D + #define PM49FL004 0x006E + #define PM49FL008 0x006A +@@ -1249,6 +1253,54 @@ static const struct amd_flash_info jedec + ERASEINFO(0x02000,2), + ERASEINFO(0x04000,1), + } ++ }, { ++ .mfr_id = MANUFACTURER_PMC, ++ .dev_id = PM39LV512, ++ .name = "PMC Pm39LV512", ++ .devtypes = CFI_DEVICETYPE_X8, ++ .uaddr = MTD_UADDR_0x0555_0x02AA, ++ .dev_size = SIZE_64KiB, ++ .cmd_set = P_ID_AMD_STD, ++ .nr_regions = 1, ++ .regions = { ++ ERASEINFO(0x01000,16), ++ } ++ }, { ++ .mfr_id = MANUFACTURER_PMC, ++ .dev_id = PM39LV010, ++ .name = "PMC Pm39LV010", ++ .devtypes = CFI_DEVICETYPE_X8, ++ .uaddr = MTD_UADDR_0x0555_0x02AA, ++ .dev_size = SIZE_128KiB, ++ .cmd_set = P_ID_AMD_STD, ++ .nr_regions = 1, ++ .regions = { ++ ERASEINFO(0x01000,32), ++ } ++ }, { ++ .mfr_id = MANUFACTURER_PMC, ++ .dev_id = PM39LV020, ++ .name = "PMC Pm39LV020", ++ .devtypes = CFI_DEVICETYPE_X8, ++ .uaddr = MTD_UADDR_0x0555_0x02AA, ++ .dev_size = SIZE_256KiB, ++ .cmd_set = P_ID_AMD_STD, ++ .nr_regions = 1, ++ .regions = { ++ ERASEINFO(0x01000,64), ++ } ++ }, { ++ .mfr_id = MANUFACTURER_PMC, ++ .dev_id = PM39LV040, ++ .name = "PMC Pm39LV040", ++ .devtypes = CFI_DEVICETYPE_X8, ++ .uaddr = MTD_UADDR_0x0555_0x02AA, ++ .dev_size = SIZE_512KiB, ++ .cmd_set = P_ID_AMD_STD, ++ .nr_regions = 1, ++ .regions = { ++ ERASEINFO(0x01000,128), ++ } + }, { + .mfr_id = MANUFACTURER_PMC, + .dev_id = PM49FL002, diff --git a/target/linux/adm5120/patches-2.6.30/103-mtd_trxsplit.patch b/target/linux/adm5120/patches-2.6.30/103-mtd_trxsplit.patch new file mode 100644 index 0000000000..69f1035505 --- /dev/null +++ b/target/linux/adm5120/patches-2.6.30/103-mtd_trxsplit.patch @@ -0,0 +1,24 @@ +--- a/drivers/mtd/Kconfig ++++ b/drivers/mtd/Kconfig +@@ -63,6 +63,11 @@ config MTD_ROOTFS_SPLIT + depends on MTD_PARTITIONS + default y + ++config MTD_TRXSPLIT ++ bool "Automatically find and split TRX partitions" ++ depends on MTD_PARTITIONS ++ default n ++ + config MTD_REDBOOT_PARTS + tristate "RedBoot partition table parsing" + depends on MTD_PARTITIONS +--- a/drivers/mtd/Makefile ++++ b/drivers/mtd/Makefile +@@ -8,6 +8,7 @@ mtd-y := mtdcore.o mtdsuper.o mtdbdi. + mtd-$(CONFIG_MTD_PARTITIONS) += mtdpart.o + + obj-$(CONFIG_MTD_CONCAT) += mtdconcat.o ++obj-$(CONFIG_MTD_TRXSPLIT) += trxsplit.o + obj-$(CONFIG_MTD_REDBOOT_PARTS) += redboot.o + obj-$(CONFIG_MTD_CMDLINE_PARTS) += cmdlinepart.o + obj-$(CONFIG_MTD_AFS_PARTS) += afs.o diff --git a/target/linux/adm5120/patches-2.6.30/120-rb153_cf_driver.patch b/target/linux/adm5120/patches-2.6.30/120-rb153_cf_driver.patch new file mode 100644 index 0000000000..3d9bbdd51a --- /dev/null +++ b/target/linux/adm5120/patches-2.6.30/120-rb153_cf_driver.patch @@ -0,0 +1,28 @@ +--- a/drivers/ata/Makefile ++++ b/drivers/ata/Makefile +@@ -73,6 +73,7 @@ obj-$(CONFIG_PATA_OCTEON_CF) += pata_oct + obj-$(CONFIG_PATA_PLATFORM) += pata_platform.o + obj-$(CONFIG_PATA_OF_PLATFORM) += pata_of_platform.o + obj-$(CONFIG_PATA_ICSIDE) += pata_icside.o ++obj-$(CONFIG_PATA_RB153_CF) += pata_rb153_cf.o + # Should be last but two libata driver + obj-$(CONFIG_PATA_ACPI) += pata_acpi.o + # Should be last but one libata driver +--- a/drivers/ata/Kconfig ++++ b/drivers/ata/Kconfig +@@ -568,6 +568,15 @@ config PATA_RADISYS + + If unsure, say N. + ++config PATA_RB153_CF ++ tristate "RouterBOARD 153 Compact Flash support" ++ depends on ADM5120_MACH_RB_153 ++ help ++ This option enables support for a Compact Flash connected on ++ the RouterBOARD 153. ++ ++ If unsure, say N. ++ + config PATA_RB532 + tristate "RouterBoard 532 PATA CompactFlash support" + depends on MIKROTIK_RB532 diff --git a/target/linux/adm5120/patches-2.6.30/140-cmdline_hack.patch b/target/linux/adm5120/patches-2.6.30/140-cmdline_hack.patch new file mode 100644 index 0000000000..14172fcaf9 --- /dev/null +++ b/target/linux/adm5120/patches-2.6.30/140-cmdline_hack.patch @@ -0,0 +1,15 @@ +--- a/arch/mips/kernel/head.S ++++ b/arch/mips/kernel/head.S +@@ -127,7 +127,12 @@ + /* + * Reserved space for exception handlers. + * Necessary for machines which link their kernels at KSEG0. ++ * Use as temporary storage for the kernel command line, so that it ++ * can be updated easily without having to relink the kernel. + */ ++ ++EXPORT(_image_cmdline) ++ .ascii "CMDLINE:" + .fill 0x400 + #endif + diff --git a/target/linux/adm5120/patches-2.6.30/200-amba_pl010_hacks.patch b/target/linux/adm5120/patches-2.6.30/200-amba_pl010_hacks.patch new file mode 100644 index 0000000000..285764411e --- /dev/null +++ b/target/linux/adm5120/patches-2.6.30/200-amba_pl010_hacks.patch @@ -0,0 +1,378 @@ +--- a/drivers/serial/amba-pl010.c ++++ b/drivers/serial/amba-pl010.c +@@ -50,11 +50,10 @@ + + #include + +-#define UART_NR 8 +- + #define SERIAL_AMBA_MAJOR 204 + #define SERIAL_AMBA_MINOR 16 +-#define SERIAL_AMBA_NR UART_NR ++#define SERIAL_AMBA_NR CONFIG_SERIAL_AMBA_PL010_NUMPORTS ++#define SERIAL_AMBA_NAME CONFIG_SERIAL_AMBA_PL010_PORTNAME + + #define AMBA_ISR_PASS_LIMIT 256 + +@@ -80,9 +79,9 @@ static void pl010_stop_tx(struct uart_po + struct uart_amba_port *uap = (struct uart_amba_port *)port; + unsigned int cr; + +- cr = readb(uap->port.membase + UART010_CR); ++ cr = __raw_readl(uap->port.membase + UART010_CR); + cr &= ~UART010_CR_TIE; +- writel(cr, uap->port.membase + UART010_CR); ++ __raw_writel(cr, uap->port.membase + UART010_CR); + } + + static void pl010_start_tx(struct uart_port *port) +@@ -90,9 +89,9 @@ static void pl010_start_tx(struct uart_p + struct uart_amba_port *uap = (struct uart_amba_port *)port; + unsigned int cr; + +- cr = readb(uap->port.membase + UART010_CR); ++ cr = __raw_readl(uap->port.membase + UART010_CR); + cr |= UART010_CR_TIE; +- writel(cr, uap->port.membase + UART010_CR); ++ __raw_writel(cr, uap->port.membase + UART010_CR); + } + + static void pl010_stop_rx(struct uart_port *port) +@@ -100,9 +99,9 @@ static void pl010_stop_rx(struct uart_po + struct uart_amba_port *uap = (struct uart_amba_port *)port; + unsigned int cr; + +- cr = readb(uap->port.membase + UART010_CR); ++ cr = __raw_readl(uap->port.membase + UART010_CR); + cr &= ~(UART010_CR_RIE | UART010_CR_RTIE); +- writel(cr, uap->port.membase + UART010_CR); ++ __raw_writel(cr, uap->port.membase + UART010_CR); + } + + static void pl010_enable_ms(struct uart_port *port) +@@ -110,9 +109,9 @@ static void pl010_enable_ms(struct uart_ + struct uart_amba_port *uap = (struct uart_amba_port *)port; + unsigned int cr; + +- cr = readb(uap->port.membase + UART010_CR); ++ cr = __raw_readl(uap->port.membase + UART010_CR); + cr |= UART010_CR_MSIE; +- writel(cr, uap->port.membase + UART010_CR); ++ __raw_writel(cr, uap->port.membase + UART010_CR); + } + + static void pl010_rx_chars(struct uart_amba_port *uap) +@@ -120,9 +119,9 @@ static void pl010_rx_chars(struct uart_a + struct tty_struct *tty = uap->port.info->port.tty; + unsigned int status, ch, flag, rsr, max_count = 256; + +- status = readb(uap->port.membase + UART01x_FR); ++ status = __raw_readl(uap->port.membase + UART01x_FR); + while (UART_RX_DATA(status) && max_count--) { +- ch = readb(uap->port.membase + UART01x_DR); ++ ch = __raw_readl(uap->port.membase + UART01x_DR); + flag = TTY_NORMAL; + + uap->port.icount.rx++; +@@ -131,9 +130,9 @@ static void pl010_rx_chars(struct uart_a + * Note that the error handling code is + * out of the main execution path + */ +- rsr = readb(uap->port.membase + UART01x_RSR) | UART_DUMMY_RSR_RX; ++ rsr = __raw_readl(uap->port.membase + UART01x_RSR) | UART_DUMMY_RSR_RX; + if (unlikely(rsr & UART01x_RSR_ANY)) { +- writel(0, uap->port.membase + UART01x_ECR); ++ __raw_writel(0, uap->port.membase + UART01x_ECR); + + if (rsr & UART01x_RSR_BE) { + rsr &= ~(UART01x_RSR_FE | UART01x_RSR_PE); +@@ -163,7 +162,7 @@ static void pl010_rx_chars(struct uart_a + uart_insert_char(&uap->port, rsr, UART01x_RSR_OE, ch, flag); + + ignore_char: +- status = readb(uap->port.membase + UART01x_FR); ++ status = __raw_readl(uap->port.membase + UART01x_FR); + } + spin_unlock(&uap->port.lock); + tty_flip_buffer_push(tty); +@@ -176,7 +175,7 @@ static void pl010_tx_chars(struct uart_a + int count; + + if (uap->port.x_char) { +- writel(uap->port.x_char, uap->port.membase + UART01x_DR); ++ __raw_writel(uap->port.x_char, uap->port.membase + UART01x_DR); + uap->port.icount.tx++; + uap->port.x_char = 0; + return; +@@ -188,7 +187,7 @@ static void pl010_tx_chars(struct uart_a + + count = uap->port.fifosize >> 1; + do { +- writel(xmit->buf[xmit->tail], uap->port.membase + UART01x_DR); ++ __raw_writel(xmit->buf[xmit->tail], uap->port.membase + UART01x_DR); + xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); + uap->port.icount.tx++; + if (uart_circ_empty(xmit)) +@@ -206,9 +205,9 @@ static void pl010_modem_status(struct ua + { + unsigned int status, delta; + +- writel(0, uap->port.membase + UART010_ICR); ++ __raw_writel(0, uap->port.membase + UART010_ICR); + +- status = readb(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY; ++ status = __raw_readl(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY; + + delta = status ^ uap->old_status; + uap->old_status = status; +@@ -236,7 +235,7 @@ static irqreturn_t pl010_int(int irq, vo + + spin_lock(&uap->port.lock); + +- status = readb(uap->port.membase + UART010_IIR); ++ status = __raw_readl(uap->port.membase + UART010_IIR); + if (status) { + do { + if (status & (UART010_IIR_RTIS | UART010_IIR_RIS)) +@@ -249,7 +248,7 @@ static irqreturn_t pl010_int(int irq, vo + if (pass_counter-- == 0) + break; + +- status = readb(uap->port.membase + UART010_IIR); ++ status = __raw_readl(uap->port.membase + UART010_IIR); + } while (status & (UART010_IIR_RTIS | UART010_IIR_RIS | + UART010_IIR_TIS)); + handled = 1; +@@ -263,7 +262,7 @@ static irqreturn_t pl010_int(int irq, vo + static unsigned int pl010_tx_empty(struct uart_port *port) + { + struct uart_amba_port *uap = (struct uart_amba_port *)port; +- unsigned int status = readb(uap->port.membase + UART01x_FR); ++ unsigned int status = __raw_readl(uap->port.membase + UART01x_FR); + return status & UART01x_FR_BUSY ? 0 : TIOCSER_TEMT; + } + +@@ -273,7 +272,7 @@ static unsigned int pl010_get_mctrl(stru + unsigned int result = 0; + unsigned int status; + +- status = readb(uap->port.membase + UART01x_FR); ++ status = __raw_readl(uap->port.membase + UART01x_FR); + if (status & UART01x_FR_DCD) + result |= TIOCM_CAR; + if (status & UART01x_FR_DSR) +@@ -299,12 +298,12 @@ static void pl010_break_ctl(struct uart_ + unsigned int lcr_h; + + spin_lock_irqsave(&uap->port.lock, flags); +- lcr_h = readb(uap->port.membase + UART010_LCRH); ++ lcr_h = __raw_readl(uap->port.membase + UART010_LCRH); + if (break_state == -1) + lcr_h |= UART01x_LCRH_BRK; + else + lcr_h &= ~UART01x_LCRH_BRK; +- writel(lcr_h, uap->port.membase + UART010_LCRH); ++ __raw_writel(lcr_h, uap->port.membase + UART010_LCRH); + spin_unlock_irqrestore(&uap->port.lock, flags); + } + +@@ -332,12 +331,12 @@ static int pl010_startup(struct uart_por + /* + * initialise the old status of the modem signals + */ +- uap->old_status = readb(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY; ++ uap->old_status = __raw_readl(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY; + + /* + * Finally, enable interrupts + */ +- writel(UART01x_CR_UARTEN | UART010_CR_RIE | UART010_CR_RTIE, ++ __raw_writel(UART01x_CR_UARTEN | UART010_CR_RIE | UART010_CR_RTIE, + uap->port.membase + UART010_CR); + + return 0; +@@ -360,10 +359,10 @@ static void pl010_shutdown(struct uart_p + /* + * disable all interrupts, disable the port + */ +- writel(0, uap->port.membase + UART010_CR); ++ __raw_writel(0, uap->port.membase + UART010_CR); + + /* disable break condition and fifos */ +- writel(readb(uap->port.membase + UART010_LCRH) & ++ __raw_writel(__raw_readl(uap->port.membase + UART010_LCRH) & + ~(UART01x_LCRH_BRK | UART01x_LCRH_FEN), + uap->port.membase + UART010_LCRH); + +@@ -385,7 +384,7 @@ pl010_set_termios(struct uart_port *port + /* + * Ask the core to calculate the divisor for us. + */ +- baud = uart_get_baud_rate(port, termios, old, 0, uap->port.uartclk/16); ++ baud = uart_get_baud_rate(port, termios, old, 0, uap->port.uartclk/16); + quot = uart_get_divisor(port, baud); + + switch (termios->c_cflag & CSIZE) { +@@ -448,25 +447,25 @@ pl010_set_termios(struct uart_port *port + uap->port.ignore_status_mask |= UART_DUMMY_RSR_RX; + + /* first, disable everything */ +- old_cr = readb(uap->port.membase + UART010_CR) & ~UART010_CR_MSIE; ++ old_cr = __raw_readl(uap->port.membase + UART010_CR) & ~UART010_CR_MSIE; + + if (UART_ENABLE_MS(port, termios->c_cflag)) + old_cr |= UART010_CR_MSIE; + +- writel(0, uap->port.membase + UART010_CR); ++ __raw_writel(0, uap->port.membase + UART010_CR); + + /* Set baud rate */ + quot -= 1; +- writel((quot & 0xf00) >> 8, uap->port.membase + UART010_LCRM); +- writel(quot & 0xff, uap->port.membase + UART010_LCRL); ++ __raw_writel((quot & 0xf00) >> 8, uap->port.membase + UART010_LCRM); ++ __raw_writel(quot & 0xff, uap->port.membase + UART010_LCRL); + + /* + * ----------v----------v----------v----------v----- + * NOTE: MUST BE WRITTEN AFTER UARTLCR_M & UARTLCR_L + * ----------^----------^----------^----------^----- + */ +- writel(lcr_h, uap->port.membase + UART010_LCRH); +- writel(old_cr, uap->port.membase + UART010_CR); ++ __raw_writel(lcr_h, uap->port.membase + UART010_LCRH); ++ __raw_writel(old_cr, uap->port.membase + UART010_CR); + + spin_unlock_irqrestore(&uap->port.lock, flags); + } +@@ -538,7 +537,7 @@ static struct uart_ops amba_pl010_pops = + .verify_port = pl010_verify_port, + }; + +-static struct uart_amba_port *amba_ports[UART_NR]; ++static struct uart_amba_port *amba_ports[SERIAL_AMBA_NR]; + + #ifdef CONFIG_SERIAL_AMBA_PL010_CONSOLE + +@@ -548,10 +547,10 @@ static void pl010_console_putchar(struct + unsigned int status; + + do { +- status = readb(uap->port.membase + UART01x_FR); ++ status = __raw_readl(uap->port.membase + UART01x_FR); + barrier(); + } while (!UART_TX_READY(status)); +- writel(ch, uap->port.membase + UART01x_DR); ++ __raw_writel(ch, uap->port.membase + UART01x_DR); + } + + static void +@@ -565,8 +564,8 @@ pl010_console_write(struct console *co, + /* + * First save the CR then disable the interrupts + */ +- old_cr = readb(uap->port.membase + UART010_CR); +- writel(UART01x_CR_UARTEN, uap->port.membase + UART010_CR); ++ old_cr = __raw_readl(uap->port.membase + UART010_CR); ++ __raw_writel(UART01x_CR_UARTEN, uap->port.membase + UART010_CR); + + uart_console_write(&uap->port, s, count, pl010_console_putchar); + +@@ -575,10 +574,10 @@ pl010_console_write(struct console *co, + * and restore the TCR + */ + do { +- status = readb(uap->port.membase + UART01x_FR); ++ status = __raw_readl(uap->port.membase + UART01x_FR); + barrier(); + } while (status & UART01x_FR_BUSY); +- writel(old_cr, uap->port.membase + UART010_CR); ++ __raw_writel(old_cr, uap->port.membase + UART010_CR); + + clk_disable(uap->clk); + } +@@ -587,9 +586,9 @@ static void __init + pl010_console_get_options(struct uart_amba_port *uap, int *baud, + int *parity, int *bits) + { +- if (readb(uap->port.membase + UART010_CR) & UART01x_CR_UARTEN) { ++ if (__raw_readl(uap->port.membase + UART010_CR) & UART01x_CR_UARTEN) { + unsigned int lcr_h, quot; +- lcr_h = readb(uap->port.membase + UART010_LCRH); ++ lcr_h = __raw_readl(uap->port.membase + UART010_LCRH); + + *parity = 'n'; + if (lcr_h & UART01x_LCRH_PEN) { +@@ -604,8 +603,8 @@ pl010_console_get_options(struct uart_am + else + *bits = 8; + +- quot = readb(uap->port.membase + UART010_LCRL) | +- readb(uap->port.membase + UART010_LCRM) << 8; ++ quot = __raw_readl(uap->port.membase + UART010_LCRL) | ++ __raw_readl(uap->port.membase + UART010_LCRM) << 8; + *baud = uap->port.uartclk / (16 * (quot + 1)); + } + } +@@ -623,7 +622,7 @@ static int __init pl010_console_setup(st + * if so, search for the first available port that does have + * console support. + */ +- if (co->index >= UART_NR) ++ if (co->index >= SERIAL_AMBA_NR) + co->index = 0; + uap = amba_ports[co->index]; + if (!uap) +@@ -641,7 +640,7 @@ static int __init pl010_console_setup(st + + static struct uart_driver amba_reg; + static struct console amba_console = { +- .name = "ttyAM", ++ .name = SERIAL_AMBA_NAME, + .write = pl010_console_write, + .device = uart_console_device, + .setup = pl010_console_setup, +@@ -657,11 +656,11 @@ static struct console amba_console = { + + static struct uart_driver amba_reg = { + .owner = THIS_MODULE, +- .driver_name = "ttyAM", +- .dev_name = "ttyAM", ++ .driver_name = SERIAL_AMBA_NAME, ++ .dev_name = SERIAL_AMBA_NAME, + .major = SERIAL_AMBA_MAJOR, + .minor = SERIAL_AMBA_MINOR, +- .nr = UART_NR, ++ .nr = SERIAL_AMBA_NR, + .cons = AMBA_CONSOLE, + }; + +--- a/drivers/serial/Kconfig ++++ b/drivers/serial/Kconfig +@@ -284,10 +284,25 @@ config SERIAL_AMBA_PL010 + help + This selects the ARM(R) AMBA(R) PrimeCell PL010 UART. If you have + an Integrator/AP or Integrator/PP2 platform, or if you have a +- Cirrus Logic EP93xx CPU, say Y or M here. ++ Cirrus Logic EP93xx CPU or an Infineon ADM5120 SOC, say Y or M here. + + If unsure, say N. + ++config SERIAL_AMBA_PL010_NUMPORTS ++ int "Maximum number of AMBA PL010 serial ports" ++ depends on SERIAL_AMBA_PL010 ++ default "8" ++ ---help--- ++ Set this to the number of serial ports you want the AMBA PL010 driver ++ to support. ++ ++config SERIAL_AMBA_PL010_PORTNAME ++ string "Name of the AMBA PL010 serial ports" ++ depends on SERIAL_AMBA_PL010 ++ default "ttyAM" ++ ---help--- ++ ::: To be written ::: ++ + config SERIAL_AMBA_PL010_CONSOLE + bool "Support for console on AMBA serial port" + depends on SERIAL_AMBA_PL010=y diff --git a/target/linux/adm5120/patches-2.6.30/201-amba_bus_hacks.patch b/target/linux/adm5120/patches-2.6.30/201-amba_bus_hacks.patch new file mode 100644 index 0000000000..9db3e55adb --- /dev/null +++ b/target/linux/adm5120/patches-2.6.30/201-amba_bus_hacks.patch @@ -0,0 +1,13 @@ +--- a/drivers/amba/bus.c ++++ b/drivers/amba/bus.c +@@ -18,6 +18,10 @@ + #include + #include + ++#ifndef NO_IRQ ++#define NO_IRQ (-1) ++#endif ++ + #define to_amba_device(d) container_of(d, struct amba_device, dev) + #define to_amba_driver(d) container_of(d, struct amba_driver, drv) + diff --git a/target/linux/adm5120/patches-2.6.30/202-pci_disable_common_quirks.patch b/target/linux/adm5120/patches-2.6.30/202-pci_disable_common_quirks.patch new file mode 100644 index 0000000000..4e6328318c --- /dev/null +++ b/target/linux/adm5120/patches-2.6.30/202-pci_disable_common_quirks.patch @@ -0,0 +1,191 @@ +--- a/drivers/pci/Kconfig ++++ b/drivers/pci/Kconfig +@@ -51,6 +51,12 @@ config PCI_STUB + + When in doubt, say N. + ++config PCI_DISABLE_COMMON_QUIRKS ++ bool "PCI disable common quirks" ++ depends on PCI ++ help ++ If you don't know what to do here, say N. ++ + config HT_IRQ + bool "Interrupts on hypertransport devices" + default y +--- a/drivers/pci/quirks.c ++++ b/drivers/pci/quirks.c +@@ -98,6 +98,7 @@ static void __devinit quirk_resource_ali + } + DECLARE_PCI_FIXUP_HEADER(PCI_ANY_ID, PCI_ANY_ID, quirk_resource_alignment); + ++#ifndef CONFIG_PCI_DISABLE_COMMON_QUIRKS + /* The Mellanox Tavor device gives false positive parity errors + * Mark this device with a broken_parity_status, to allow + * PCI scanning code to "skip" this now blacklisted device. +@@ -132,11 +133,11 @@ DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_I + + /* The VIA VP2/VP3/MVP3 seem to have some 'features'. There may be a workaround + but VIA don't answer queries. If you happen to have good contacts at VIA +- ask them for me please -- Alan +- +- This appears to be BIOS not version dependent. So presumably there is a ++ ask them for me please -- Alan ++ ++ This appears to be BIOS not version dependent. So presumably there is a + chipset level fix */ +- ++ + static void __devinit quirk_isa_dma_hangs(struct pci_dev *dev) + { + if (!isa_dma_bridge_buggy) { +@@ -204,7 +205,7 @@ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_IN + * the info on which Mr Breese based his work. + * + * Updated based on further information from the site and also on +- * information provided by VIA ++ * information provided by VIA + */ + static void quirk_vialatency(struct pci_dev *dev) + { +@@ -212,7 +213,7 @@ static void quirk_vialatency(struct pci_ + u8 busarb; + /* Ok we have a potential problem chipset here. Now see if we have + a buggy southbridge */ +- ++ + p = pci_get_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686, NULL); + if (p!=NULL) { + /* 0x40 - 0x4f == 686B, 0x10 - 0x2f == 686A; thanks Dan Hollis */ +@@ -227,9 +228,9 @@ static void quirk_vialatency(struct pci_ + if (p->revision < 0x10 || p->revision > 0x12) + goto exit; + } +- ++ + /* +- * Ok we have the problem. Now set the PCI master grant to ++ * Ok we have the problem. Now set the PCI master grant to + * occur every master grant. The apparent bug is that under high + * PCI load (quite common in Linux of course) you can get data + * loss when the CPU is held off the bus for 3 bus master requests +@@ -242,7 +243,7 @@ static void quirk_vialatency(struct pci_ + */ + + pci_read_config_byte(dev, 0x76, &busarb); +- /* Set bit 4 and bi 5 of byte 76 to 0x01 ++ /* Set bit 4 and bi 5 of byte 76 to 0x01 + "Master priority rotation on every PCI master grant */ + busarb &= ~(1<<5); + busarb |= (1<<4); +@@ -285,7 +286,7 @@ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VI + * that DMA to AGP space. Latency must be set to 0xA and triton + * workaround applied too + * [Info kindly provided by ALi] +- */ ++ */ + static void __init quirk_alimagik(struct pci_dev *dev) + { + if ((pci_pci_problems&PCIPCI_ALIMAGIK)==0) { +@@ -361,7 +362,7 @@ static void __devinit quirk_io_region(st + pci_claim_resource(dev, nr); + dev_info(&dev->dev, "quirk: region %04x-%04x claimed by %s\n", region, region + size - 1, name); + } +-} ++} + + /* + * ATI Northbridge setups MCE the processor if you even +@@ -418,7 +419,7 @@ static void piix4_io_quirk(struct pci_de + /* + * For now we only print it out. Eventually we'll want to + * reserve it (at least if it's in the 0x1000+ range), but +- * let's get enough confirmation reports first. ++ * let's get enough confirmation reports first. + */ + base &= -size; + dev_info(&dev->dev, "%s PIO at %04x-%04x\n", name, base, base + size - 1); +@@ -443,7 +444,7 @@ static void piix4_mem_quirk(struct pci_d + } + /* + * For now we only print it out. Eventually we'll want to +- * reserve it, but let's get enough confirmation reports first. ++ * reserve it, but let's get enough confirmation reports first. + */ + base &= -size; + dev_info(&dev->dev, "%s MMIO at %04x-%04x\n", name, base, base + size - 1); +@@ -673,7 +674,7 @@ static void __devinit quirk_vt8235_acpi( + DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8235, quirk_vt8235_acpi); + + +-#ifdef CONFIG_X86_IO_APIC ++#ifdef CONFIG_X86_IO_APIC + + #include + +@@ -687,12 +688,12 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_V + static void quirk_via_ioapic(struct pci_dev *dev) + { + u8 tmp; +- ++ + if (nr_ioapics < 1) + tmp = 0; /* nothing routed to external APIC */ + else + tmp = 0x1f; /* all known bits (4-0) routed to external APIC */ +- ++ + dev_info(&dev->dev, "%sbling VIA external APIC routing\n", + tmp == 0 ? "Disa" : "Ena"); + +@@ -977,7 +978,7 @@ DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_C + static void quirk_disable_pxb(struct pci_dev *pdev) + { + u16 config; +- ++ + if (pdev->revision != 0x04) /* Only C0 requires this */ + return; + pci_read_config_word(pdev, 0x40, &config); +@@ -1073,11 +1074,11 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_I + * On ASUS P4B boards, the SMBus PCI Device within the ICH2/4 southbridge + * is not activated. The myth is that Asus said that they do not want the + * users to be irritated by just another PCI Device in the Win98 device +- * manager. (see the file prog/hotplug/README.p4b in the lm_sensors ++ * manager. (see the file prog/hotplug/README.p4b in the lm_sensors + * package 2.7.0 for details) + * +- * The SMBus PCI Device can be activated by setting a bit in the ICH LPC +- * bridge. Unfortunately, this device has no subvendor/subdevice ID. So it ++ * The SMBus PCI Device can be activated by setting a bit in the ICH LPC ++ * bridge. Unfortunately, this device has no subvendor/subdevice ID. So it + * becomes necessary to do this tweak in two steps -- the chosen trigger + * is either the Host bridge (preferred) or on-board VGA controller. + * +@@ -1229,7 +1230,7 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_I + static void asus_hides_smbus_lpc(struct pci_dev *dev) + { + u16 val; +- ++ + if (likely(!asus_hides_smbus)) + return; + +@@ -1859,7 +1860,9 @@ static void __devinit fixup_rev1_53c810( + } + } + DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NCR, PCI_DEVICE_ID_NCR_53C810, fixup_rev1_53c810); ++#endif /* !CONFIG_PCI_DISABLE_COMMON_QUIRKS */ + ++#ifndef CONFIG_PCI_DISABLE_COMMON_QUIRKS + /* Enable 1k I/O space granularity on the Intel P64H2 */ + static void __devinit quirk_p64h2_1k_io(struct pci_dev *dev) + { +@@ -2463,6 +2466,7 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_I + DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x10e7, quirk_i82576_sriov); + + #endif /* CONFIG_PCI_IOV */ ++#endif /* !CONFIG_PCI_DISABLE_COMMON_QUIRKS */ + + static void pci_do_fixups(struct pci_dev *dev, struct pci_fixup *f, + struct pci_fixup *end) diff --git a/target/linux/adm5120/patches-2.6.30/203-gpio_leds_brightness.patch b/target/linux/adm5120/patches-2.6.30/203-gpio_leds_brightness.patch new file mode 100644 index 0000000000..8bccf395c1 --- /dev/null +++ b/target/linux/adm5120/patches-2.6.30/203-gpio_leds_brightness.patch @@ -0,0 +1,27 @@ +--- a/drivers/leds/leds-gpio.c ++++ b/drivers/leds/leds-gpio.c +@@ -44,13 +44,17 @@ static void gpio_led_set(struct led_clas + container_of(led_cdev, struct gpio_led_data, cdev); + int level; + +- if (value == LED_OFF) +- level = 0; +- else +- level = 1; +- +- if (led_dat->active_low) +- level = !level; ++ switch (value) { ++ case LED_OFF: ++ level = led_dat->active_low ? 1 : 0; ++ break; ++ case LED_FULL: ++ level = led_dat->active_low ? 0 : 1; ++ break; ++ default: ++ level = value; ++ break; ++ } + + /* Setting GPIOs with I2C/etc requires a task context, and we don't + * seem to have a reliable way to know if we're already in one; so diff --git a/target/linux/adm5120/patches-2.6.30/310-adm5120_wdt.patch b/target/linux/adm5120/patches-2.6.30/310-adm5120_wdt.patch new file mode 100644 index 0000000000..bb5e613d95 --- /dev/null +++ b/target/linux/adm5120/patches-2.6.30/310-adm5120_wdt.patch @@ -0,0 +1,31 @@ +--- a/drivers/watchdog/Kconfig ++++ b/drivers/watchdog/Kconfig +@@ -713,6 +713,18 @@ config RC32434_WDT + To compile this driver as a module, choose M here: the + module will be called rc32434_wdt. + ++config ADM5120_WDT ++ tristate "Infineon ADM5120 SoC hardware watchdog" ++ depends on WATCHDOG && ADM5120 ++ help ++ This is a driver for hardware watchdog integrated in Infineon ++ ADM5120 SoC. This watchdog simply watches your kernel to make sure ++ it doesn't freeze, and if it does, it reboots your computer after a ++ certain amount of time. ++ ++ To compile this driver as a module, choose M here: the module will be ++ called adm5120_wdt. ++ + config INDYDOG + tristate "Indy/I2 Hardware Watchdog" + depends on SGI_HAS_INDYDOG +--- a/drivers/watchdog/Makefile ++++ b/drivers/watchdog/Makefile +@@ -105,6 +105,7 @@ obj-$(CONFIG_WDT_RM9K_GPI) += rm9k_wdt.o + obj-$(CONFIG_SIBYTE_WDOG) += sb_wdog.o + obj-$(CONFIG_AR7_WDT) += ar7_wdt.o + obj-$(CONFIG_TXX9_WDT) += txx9wdt.o ++obj-$(CONFIG_ADM5120_WDT) += adm5120_wdt.o + + # PARISC Architecture + diff --git a/target/linux/adm5120/patches-2.6.30/800-adm5120-remove-amba-bus-id.patch b/target/linux/adm5120/patches-2.6.30/800-adm5120-remove-amba-bus-id.patch new file mode 100644 index 0000000000..e2435fbfab --- /dev/null +++ b/target/linux/adm5120/patches-2.6.30/800-adm5120-remove-amba-bus-id.patch @@ -0,0 +1,18 @@ +--- a/arch/mips/adm5120/common/platform.c ++++ b/arch/mips/adm5120/common/platform.c +@@ -190,7 +190,6 @@ struct amba_pl010_data adm5120_uart0_dat + + struct amba_device adm5120_uart0_device = { + .dev = { +- .bus_id = "APB:UART0", + .platform_data = &adm5120_uart0_data, + }, + .res = { +@@ -208,7 +207,6 @@ struct amba_pl010_data adm5120_uart1_dat + + struct amba_device adm5120_uart1_device = { + .dev = { +- .bus_id = "APB:UART1", + .platform_data = &adm5120_uart1_data, + }, + .res = { diff --git a/target/linux/adm5120/patches-2.6.30/801-adm5120-flash-remove-bus-id.patch b/target/linux/adm5120/patches-2.6.30/801-adm5120-flash-remove-bus-id.patch new file mode 100644 index 0000000000..d9e72e064b --- /dev/null +++ b/target/linux/adm5120/patches-2.6.30/801-adm5120-flash-remove-bus-id.patch @@ -0,0 +1,11 @@ +--- a/drivers/mtd/maps/adm5120-flash.c ++++ b/drivers/mtd/maps/adm5120-flash.c +@@ -233,7 +233,7 @@ static int adm5120_flash_initinfo(struct + struct flash_desc *fdesc; + u32 t = 0; + +- map->name = dev->dev.bus_id; ++ map->name = dev_name(&dev->dev); + + if (dev->id > 1) { + MAP_ERR(map, "invalid flash id\n"); diff --git a/target/linux/adm5120/patches-2.6.30/802-adm5120-switch-remove-redundant-napi-functions.patch b/target/linux/adm5120/patches-2.6.30/802-adm5120-switch-remove-redundant-napi-functions.patch new file mode 100644 index 0000000000..5c5873b731 --- /dev/null +++ b/target/linux/adm5120/patches-2.6.30/802-adm5120-switch-remove-redundant-napi-functions.patch @@ -0,0 +1,20 @@ +--- a/drivers/net/adm5120sw.c ++++ b/drivers/net/adm5120sw.c +@@ -517,7 +517,7 @@ static int adm5120_if_poll(struct napi_s + status = sw_int_status() & SWITCH_INTS_POLL; + if ((done < limit) && (!status)) { + SW_DBG("disable polling mode for %s\n", dev->name); +- netif_rx_complete(dev, napi); ++ napi_complete(napi); + sw_int_unmask(SWITCH_INTS_POLL); + return 0; + } +@@ -548,7 +548,7 @@ static irqreturn_t adm5120_switch_irq(in + sw_dump_intr_mask("poll ints", status); + SW_DBG("enable polling mode for %s\n", dev->name); + sw_int_mask(SWITCH_INTS_POLL); +- netif_rx_schedule(dev, &priv->napi); ++ napi_schedule(&priv->napi); + } + #else + sw_int_ack(status); diff --git a/target/linux/adm5120/router_be/config-2.6.30 b/target/linux/adm5120/router_be/config-2.6.30 new file mode 100644 index 0000000000..a4a511f06a --- /dev/null +++ b/target/linux/adm5120/router_be/config-2.6.30 @@ -0,0 +1,216 @@ +CONFIG_32BIT=y +# CONFIG_64BIT is not set +CONFIG_ADM5120=y +CONFIG_ADM5120_ENET=y +CONFIG_ADM5120_MACH_P_334WT=y +CONFIG_ADM5120_MACH_P_335=y +# CONFIG_ADM5120_OEM_CELLVISION is not set +# CONFIG_ADM5120_OEM_COMPEX is not set +# CONFIG_ADM5120_OEM_EDIMAX is not set +# CONFIG_ADM5120_OEM_INFINEON is not set +# CONFIG_ADM5120_OEM_MIKROTIK is not set +# CONFIG_ADM5120_OEM_MOTOROLA is not set +CONFIG_ADM5120_OEM_ZYXEL=y +CONFIG_ADM5120_SOC_BGA=y +CONFIG_ADM5120_WDT=y +# CONFIG_ARCH_HAS_ILOG2_U32 is not set +# CONFIG_ARCH_HAS_ILOG2_U64 is not set +CONFIG_ARCH_POPULATES_NODE_MAP=y +CONFIG_ARCH_REQUIRE_GPIOLIB=y +# CONFIG_ARCH_SUPPORTS_MSI is not set +CONFIG_ARCH_SUPPORTS_OPROFILE=y +CONFIG_ARCH_SUSPEND_POSSIBLE=y +CONFIG_ARM_AMBA=y +CONFIG_BASE_SMALL=0 +# CONFIG_BCM47XX is not set +# CONFIG_BINARY_PRINTF is not set +CONFIG_BINFMT_MISC=m +CONFIG_BITREVERSE=y +# CONFIG_CAVIUM_OCTEON_REFERENCE_BOARD is not set +# CONFIG_CAVIUM_OCTEON_SIMULATOR is not set +CONFIG_CEVT_R4K=y +CONFIG_CEVT_R4K_LIB=y +CONFIG_CMDLINE="console=ttyS0,115200 rootfstype=squashfs,jffs2" +CONFIG_CPU_BIG_ENDIAN=y +# CONFIG_CPU_CAVIUM_OCTEON is not set +CONFIG_CPU_HAS_LLSC=y +CONFIG_CPU_HAS_PREFETCH=y +CONFIG_CPU_HAS_SYNC=y +# CONFIG_CPU_LITTLE_ENDIAN is not set +# CONFIG_CPU_LOONGSON2 is not set +CONFIG_CPU_MIPS32=y +CONFIG_CPU_MIPS32_R1=y +# CONFIG_CPU_MIPS32_R2 is not set +# CONFIG_CPU_MIPS64_R1 is not set +# CONFIG_CPU_MIPS64_R2 is not set +CONFIG_CPU_MIPSR1=y +# CONFIG_CPU_NEVADA is not set +# CONFIG_CPU_R10000 is not set +# CONFIG_CPU_R3000 is not set +# CONFIG_CPU_R4300 is not set +# CONFIG_CPU_R4X00 is not set +# CONFIG_CPU_R5000 is not set +# CONFIG_CPU_R5432 is not set +# CONFIG_CPU_R5500 is not set +# CONFIG_CPU_R6000 is not set +# CONFIG_CPU_R8000 is not set +# CONFIG_CPU_RM7000 is not set +# CONFIG_CPU_RM9000 is not set +# CONFIG_CPU_SB1 is not set +CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y +CONFIG_CPU_SUPPORTS_HIGHMEM=y +# CONFIG_CPU_TX39XX is not set +# CONFIG_CPU_TX49XX is not set +# CONFIG_CPU_VR41XX is not set +CONFIG_CRYPTO_AEAD2=y +CONFIG_CRYPTO_BLKCIPHER2=y +CONFIG_CRYPTO_HASH2=y +CONFIG_CRYPTO_MANAGER2=y +CONFIG_CRYPTO_RNG2=y +CONFIG_CRYPTO_WORKQUEUE=y +CONFIG_CSRC_R4K=y +CONFIG_CSRC_R4K_LIB=y +CONFIG_DECOMPRESS_LZMA=y +CONFIG_DEVPORT=y +# CONFIG_DM9000 is not set +CONFIG_DMA_NEED_PCI_MAP_STATE=y +CONFIG_DMA_NONCOHERENT=y +CONFIG_EARLY_PRINTK=y +CONFIG_ELF_CORE=y +CONFIG_FIRMWARE_IN_KERNEL=y +CONFIG_FS_POSIX_ACL=y +CONFIG_GENERIC_ACL=y +CONFIG_GENERIC_CLOCKEVENTS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_FIND_LAST_BIT=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_GPIO=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y +CONFIG_GPIOLIB=y +CONFIG_GPIO_SYSFS=y +CONFIG_HARDWARE_WATCHPOINTS=y +CONFIG_HAS_DMA=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y +CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set +CONFIG_HAVE_IDE=y +CONFIG_HAVE_MLOCK=y +CONFIG_HAVE_OPROFILE=y +CONFIG_HID=m +CONFIG_HID_SUPPORT=y +CONFIG_HW_HAS_PCI=y +CONFIG_HW_RANDOM=y +CONFIG_HZ=250 +# CONFIG_HZ_100 is not set +CONFIG_HZ_250=y +# CONFIG_I2C is not set +CONFIG_INITRAMFS_SOURCE="" +CONFIG_INOTIFY=y +CONFIG_INOTIFY_USER=y +CONFIG_INPUT=m +# CONFIG_INPUT_GPIO_BUTTONS is not set +# CONFIG_INPUT_YEALINK is not set +CONFIG_IRQ_CPU=y +# CONFIG_ISDN is not set +CONFIG_LEDS_GPIO=m +CONFIG_LEDS_TRIGGER_ADM5120_SWITCH=m +CONFIG_LEGACY_PTYS=y +CONFIG_LEGACY_PTY_COUNT=256 +# CONFIG_LEMOTE_FULONG is not set +# CONFIG_LIB80211 is not set +# CONFIG_MACH_ALCHEMY is not set +# CONFIG_MACH_DECSTATION is not set +# CONFIG_MACH_JAZZ is not set +# CONFIG_MACH_TX39XX is not set +# CONFIG_MACH_TX49XX is not set +# CONFIG_MACH_VR41XX is not set +CONFIG_MII=m +# CONFIG_MIKROTIK_RB532 is not set +CONFIG_MIPS=y +# CONFIG_MIPS_COBALT is not set +CONFIG_MIPS_L1_CACHE_SHIFT=5 +CONFIG_MIPS_MACHINE=y +# CONFIG_MIPS_MALTA is not set +CONFIG_MIPS_MT_DISABLED=y +# CONFIG_MIPS_MT_SMP is not set +# CONFIG_MIPS_MT_SMTC is not set +# CONFIG_MIPS_SIM is not set +CONFIG_MODULE_FORCE_UNLOAD=y +CONFIG_MTD_ADM5120=y +CONFIG_MTD_BLOCK2MTD=y +CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC=y +# CONFIG_MTD_CFI_INTELEXT is not set +CONFIG_MTD_CMDLINE_PARTS=y +CONFIG_MTD_TRXSPLIT=y +# CONFIG_NET_PCI is not set +# CONFIG_NO_IOPORT is not set +# CONFIG_NXP_STB220 is not set +# CONFIG_NXP_STB225 is not set +CONFIG_PAGEFLAGS_EXTENDED=y +# CONFIG_PARTITION_ADVANCED is not set +CONFIG_PCI=y +CONFIG_PCI_DISABLE_COMMON_QUIRKS=y +CONFIG_PCI_DOMAINS=y +# CONFIG_PCI_STUB is not set +# CONFIG_PCSPKR_PLATFORM is not set +# CONFIG_PMC_MSP is not set +# CONFIG_PMC_YOSEMITE is not set +# CONFIG_PNX8550_JBS is not set +# CONFIG_PNX8550_STB810 is not set +# CONFIG_PROBE_INITRD_HEADER is not set +# CONFIG_PROM_EMU is not set +CONFIG_SCHED_OMIT_FRAME_POINTER=y +# CONFIG_SCSI_DMA is not set +# CONFIG_SERIAL_8250 is not set +CONFIG_SERIAL_AMBA_PL010=y +CONFIG_SERIAL_AMBA_PL010_CONSOLE=y +CONFIG_SERIAL_AMBA_PL010_NUMPORTS=2 +CONFIG_SERIAL_AMBA_PL010_PORTNAME="ttyS" +# CONFIG_SERIAL_AMBA_PL011 is not set +CONFIG_SERIO=y +# CONFIG_SERIO_AMBAKMI is not set +# CONFIG_SERIO_I8042 is not set +# CONFIG_SERIO_LIBPS2 is not set +# CONFIG_SERIO_PCIPS2 is not set +# CONFIG_SERIO_RAW is not set +CONFIG_SERIO_SERPORT=y +# CONFIG_SGI_IP22 is not set +# CONFIG_SGI_IP27 is not set +# CONFIG_SGI_IP28 is not set +# CONFIG_SGI_IP32 is not set +# CONFIG_SIBYTE_BIGSUR is not set +# CONFIG_SIBYTE_CARMEL is not set +# CONFIG_SIBYTE_CRHINE is not set +# CONFIG_SIBYTE_CRHONE is not set +# CONFIG_SIBYTE_LITTLESUR is not set +# CONFIG_SIBYTE_RHONE is not set +# CONFIG_SIBYTE_SENTOSA is not set +# CONFIG_SIBYTE_SWARM is not set +# CONFIG_SLAB is not set +# CONFIG_SLOW_WORK is not set +CONFIG_SLUB=y +CONFIG_SOFT_WATCHDOG=m +CONFIG_SWAP_IO_SPACE=y +CONFIG_SYS_HAS_CPU_MIPS32_R1=y +CONFIG_SYS_HAS_EARLY_PRINTK=y +CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y +CONFIG_SYS_SUPPORTS_ARBIT_HZ=y +CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y +CONFIG_SYS_SUPPORTS_LITTLE_ENDIAN=y +CONFIG_TICK_ONESHOT=y +CONFIG_TMPFS_POSIX_ACL=y +CONFIG_TRACING_SUPPORT=y +CONFIG_TRAD_SIGNALS=y +CONFIG_USB=m +CONFIG_USB_ADM5120_HCD=m +CONFIG_USB_DEBUG=y +CONFIG_USB_EHCI_HCD=m +# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set +# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set +CONFIG_USB_OHCI_HCD=m +CONFIG_USB_SUPPORT=y +# CONFIG_USB_UHCI_HCD is not set +CONFIG_VM_EVENT_COUNTERS=y +CONFIG_ZONE_DMA_FLAG=0 diff --git a/target/linux/adm5120/router_le/config-2.6.30 b/target/linux/adm5120/router_le/config-2.6.30 new file mode 100644 index 0000000000..6d65d796f1 --- /dev/null +++ b/target/linux/adm5120/router_le/config-2.6.30 @@ -0,0 +1,263 @@ +CONFIG_32BIT=y +# CONFIG_64BIT is not set +CONFIG_ADM5120=y +CONFIG_ADM5120_ENET=y +CONFIG_ADM5120_MACH_BR_6104K=y +CONFIG_ADM5120_MACH_BR_6104KP=y +CONFIG_ADM5120_MACH_BR_61X4WG=y +CONFIG_ADM5120_MACH_CAS_771=y +CONFIG_ADM5120_MACH_EASY5120P_ATA=y +CONFIG_ADM5120_MACH_EASY5120_RT=y +CONFIG_ADM5120_MACH_EASY5120_WVOIP=y +CONFIG_ADM5120_MACH_EASY83000=y +CONFIG_ADM5120_MACH_NFS_101=y +CONFIG_ADM5120_MACH_NP27G=y +CONFIG_ADM5120_MACH_NP28G=y +CONFIG_ADM5120_MACH_PMUGW=y +CONFIG_ADM5120_MACH_RB_11X=y +CONFIG_ADM5120_MACH_RB_133=y +CONFIG_ADM5120_MACH_RB_133C=y +CONFIG_ADM5120_MACH_RB_150=y +CONFIG_ADM5120_MACH_RB_153=y +CONFIG_ADM5120_MACH_RB_192=y +CONFIG_ADM5120_MACH_WP54=y +CONFIG_ADM5120_OEM_CELLVISION=y +CONFIG_ADM5120_OEM_COMPEX=y +CONFIG_ADM5120_OEM_EDIMAX=y +CONFIG_ADM5120_OEM_INFINEON=y +CONFIG_ADM5120_OEM_MIKROTIK=y +CONFIG_ADM5120_OEM_MOTOROLA=y +# CONFIG_ADM5120_OEM_ZYXEL is not set +CONFIG_ADM5120_SOC_BGA=y +CONFIG_ADM5120_WDT=y +# CONFIG_ARCH_HAS_ILOG2_U32 is not set +# CONFIG_ARCH_HAS_ILOG2_U64 is not set +CONFIG_ARCH_POPULATES_NODE_MAP=y +CONFIG_ARCH_REQUIRE_GPIOLIB=y +# CONFIG_ARCH_SUPPORTS_MSI is not set +CONFIG_ARCH_SUPPORTS_OPROFILE=y +CONFIG_ARCH_SUSPEND_POSSIBLE=y +CONFIG_ARM_AMBA=y +CONFIG_ATA=m +# CONFIG_ATA_NONSTANDARD is not set +# CONFIG_ATA_PIIX is not set +CONFIG_ATA_SFF=y +CONFIG_BASE_SMALL=0 +# CONFIG_BCM47XX is not set +# CONFIG_BINARY_PRINTF is not set +CONFIG_BITREVERSE=y +# CONFIG_CAVIUM_OCTEON_REFERENCE_BOARD is not set +# CONFIG_CAVIUM_OCTEON_SIMULATOR is not set +CONFIG_CEVT_R4K=y +CONFIG_CEVT_R4K_LIB=y +CONFIG_CMDLINE="console=ttyS0,115200 rootfstype=squashfs,yaffs2,jffs2" +# CONFIG_CPU_BIG_ENDIAN is not set +# CONFIG_CPU_CAVIUM_OCTEON is not set +CONFIG_CPU_HAS_LLSC=y +CONFIG_CPU_HAS_PREFETCH=y +CONFIG_CPU_HAS_SYNC=y +CONFIG_CPU_LITTLE_ENDIAN=y +# CONFIG_CPU_LOONGSON2 is not set +CONFIG_CPU_MIPS32=y +CONFIG_CPU_MIPS32_R1=y +# CONFIG_CPU_MIPS32_R2 is not set +# CONFIG_CPU_MIPS64_R1 is not set +# CONFIG_CPU_MIPS64_R2 is not set +CONFIG_CPU_MIPSR1=y +# CONFIG_CPU_NEVADA is not set +# CONFIG_CPU_R10000 is not set +# CONFIG_CPU_R3000 is not set +# CONFIG_CPU_R4300 is not set +# CONFIG_CPU_R4X00 is not set +# CONFIG_CPU_R5000 is not set +# CONFIG_CPU_R5432 is not set +# CONFIG_CPU_R5500 is not set +# CONFIG_CPU_R6000 is not set +# CONFIG_CPU_R8000 is not set +# CONFIG_CPU_RM7000 is not set +# CONFIG_CPU_RM9000 is not set +# CONFIG_CPU_SB1 is not set +CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y +CONFIG_CPU_SUPPORTS_HIGHMEM=y +# CONFIG_CPU_TX39XX is not set +# CONFIG_CPU_TX49XX is not set +# CONFIG_CPU_VR41XX is not set +CONFIG_CRYPTO_AEAD2=y +CONFIG_CRYPTO_BLKCIPHER2=y +CONFIG_CRYPTO_HASH=m +CONFIG_CRYPTO_HASH2=y +CONFIG_CRYPTO_MANAGER2=y +CONFIG_CRYPTO_MICHAEL_MIC=m +CONFIG_CRYPTO_RNG2=y +CONFIG_CRYPTO_WORKQUEUE=y +CONFIG_CSRC_R4K=y +CONFIG_CSRC_R4K_LIB=y +CONFIG_DECOMPRESS_LZMA=y +CONFIG_DEVPORT=y +# CONFIG_DM9000 is not set +CONFIG_DMA_NEED_PCI_MAP_STATE=y +CONFIG_DMA_NONCOHERENT=y +CONFIG_EARLY_PRINTK=y +CONFIG_ELF_CORE=y +CONFIG_FIRMWARE_IN_KERNEL=y +CONFIG_FS_POSIX_ACL=y +CONFIG_GENERIC_ACL=y +CONFIG_GENERIC_CLOCKEVENTS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_FIND_LAST_BIT=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_GPIO=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y +CONFIG_GPIOLIB=y +CONFIG_GPIO_SYSFS=y +# CONFIG_HAMRADIO is not set +CONFIG_HARDWARE_WATCHPOINTS=y +CONFIG_HAS_DMA=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y +CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set +CONFIG_HAVE_IDE=y +CONFIG_HAVE_MLOCK=y +CONFIG_HAVE_OPROFILE=y +CONFIG_HID=m +CONFIG_HID_SUPPORT=y +CONFIG_HOSTAP=m +CONFIG_HOSTAP_FIRMWARE=y +CONFIG_HOSTAP_PCI=m +CONFIG_HW_HAS_PCI=y +CONFIG_HW_RANDOM=y +CONFIG_HZ=250 +# CONFIG_HZ_100 is not set +CONFIG_HZ_250=y +# CONFIG_I2C is not set +CONFIG_INITRAMFS_SOURCE="" +CONFIG_INOTIFY=y +CONFIG_INOTIFY_USER=y +CONFIG_INPUT=m +# CONFIG_INPUT_GPIO_BUTTONS is not set +# CONFIG_INPUT_YEALINK is not set +CONFIG_IRQ_CPU=y +# CONFIG_ISDN is not set +CONFIG_KEXEC=y +CONFIG_LEDS_GPIO=m +CONFIG_LEDS_TRIGGER_ADM5120_SWITCH=m +CONFIG_LEGACY_PTYS=y +CONFIG_LEGACY_PTY_COUNT=256 +# CONFIG_LEMOTE_FULONG is not set +CONFIG_LIB80211=m +CONFIG_LIB80211_CRYPT_CCMP=m +CONFIG_LIB80211_CRYPT_TKIP=m +CONFIG_LIB80211_CRYPT_WEP=m +# CONFIG_MACH_ALCHEMY is not set +# CONFIG_MACH_DECSTATION is not set +# CONFIG_MACH_JAZZ is not set +# CONFIG_MACH_TX39XX is not set +# CONFIG_MACH_TX49XX is not set +# CONFIG_MACH_VR41XX is not set +CONFIG_MII=m +# CONFIG_MIKROTIK_RB532 is not set +CONFIG_MIPS=y +# CONFIG_MIPS_COBALT is not set +CONFIG_MIPS_L1_CACHE_SHIFT=5 +CONFIG_MIPS_MACHINE=y +# CONFIG_MIPS_MALTA is not set +CONFIG_MIPS_MT_DISABLED=y +# CONFIG_MIPS_MT_SMP is not set +# CONFIG_MIPS_MT_SMTC is not set +# CONFIG_MIPS_SIM is not set +CONFIG_MODULE_FORCE_UNLOAD=y +CONFIG_MTD_ADM5120=y +CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC=y +# CONFIG_MTD_CFI_INTELEXT is not set +CONFIG_MTD_CMDLINE_PARTS=y +CONFIG_MTD_JEDECPROBE=y +CONFIG_MTD_MYLOADER_PARTS=y +CONFIG_MTD_NAND=y +# CONFIG_MTD_NAND_CAFE is not set +CONFIG_MTD_NAND_PLATFORM=y +CONFIG_MTD_TRXSPLIT=y +# CONFIG_NATSEMI is not set +CONFIG_NO_HZ=y +# CONFIG_NO_IOPORT is not set +# CONFIG_NXP_STB220 is not set +# CONFIG_NXP_STB225 is not set +CONFIG_PAGEFLAGS_EXTENDED=y +# CONFIG_PARTITION_ADVANCED is not set +CONFIG_PATA_RB153_CF=m +# CONFIG_PATA_SCH is not set +CONFIG_PCI=y +CONFIG_PCI_DISABLE_COMMON_QUIRKS=y +CONFIG_PCI_DOMAINS=y +# CONFIG_PCI_STUB is not set +# CONFIG_PCSPKR_PLATFORM is not set +# CONFIG_PMC_MSP is not set +# CONFIG_PMC_YOSEMITE is not set +# CONFIG_PNX8550_JBS is not set +# CONFIG_PNX8550_STB810 is not set +# CONFIG_PROBE_INITRD_HEADER is not set +# CONFIG_PROM_EMU is not set +CONFIG_SCHED_OMIT_FRAME_POINTER=y +CONFIG_SCSI=m +# CONFIG_SERIAL_8250 is not set +CONFIG_SERIAL_AMBA_PL010=y +CONFIG_SERIAL_AMBA_PL010_CONSOLE=y +CONFIG_SERIAL_AMBA_PL010_NUMPORTS=2 +CONFIG_SERIAL_AMBA_PL010_PORTNAME="ttyS" +# CONFIG_SERIAL_AMBA_PL011 is not set +CONFIG_SERIO=y +# CONFIG_SERIO_AMBAKMI is not set +# CONFIG_SERIO_I8042 is not set +# CONFIG_SERIO_LIBPS2 is not set +# CONFIG_SERIO_PCIPS2 is not set +# CONFIG_SERIO_RAW is not set +CONFIG_SERIO_SERPORT=y +# CONFIG_SGI_IP22 is not set +# CONFIG_SGI_IP27 is not set +# CONFIG_SGI_IP28 is not set +# CONFIG_SGI_IP32 is not set +# CONFIG_SIBYTE_BIGSUR is not set +# CONFIG_SIBYTE_CARMEL is not set +# CONFIG_SIBYTE_CRHINE is not set +# CONFIG_SIBYTE_CRHONE is not set +# CONFIG_SIBYTE_LITTLESUR is not set +# CONFIG_SIBYTE_RHONE is not set +# CONFIG_SIBYTE_SENTOSA is not set +# CONFIG_SIBYTE_SWARM is not set +# CONFIG_SLAB is not set +# CONFIG_SLOW_WORK is not set +CONFIG_SLUB=y +CONFIG_SOFT_WATCHDOG=m +# CONFIG_SWAP is not set +CONFIG_SYS_HAS_CPU_MIPS32_R1=y +CONFIG_SYS_HAS_EARLY_PRINTK=y +CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y +CONFIG_SYS_SUPPORTS_ARBIT_HZ=y +CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y +CONFIG_SYS_SUPPORTS_LITTLE_ENDIAN=y +# CONFIG_TC35815 is not set +CONFIG_TICK_ONESHOT=y +CONFIG_TMPFS_POSIX_ACL=y +CONFIG_TRACING_SUPPORT=y +CONFIG_TRAD_SIGNALS=y +CONFIG_USB=m +CONFIG_USB_ADM5120_HCD=m +CONFIG_USB_EHCI_HCD=m +# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set +# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set +CONFIG_USB_OHCI_HCD=m +CONFIG_USB_SUPPORT=y +# CONFIG_USB_UHCI_HCD is not set +CONFIG_VLAN_8021Q=m +CONFIG_VM_EVENT_COUNTERS=y +CONFIG_YAFFS_9BYTE_TAGS=y +# CONFIG_YAFFS_ALWAYS_CHECK_CHUNK_ERASED is not set +CONFIG_YAFFS_AUTO_YAFFS2=y +# CONFIG_YAFFS_DISABLE_LAZY_LOAD is not set +# CONFIG_YAFFS_DISABLE_WIDE_TNODES is not set +CONFIG_YAFFS_FS=y +CONFIG_YAFFS_SHORT_NAMES_IN_RAM=y +CONFIG_YAFFS_YAFFS1=y +CONFIG_YAFFS_YAFFS2=y +CONFIG_ZONE_DMA_FLAG=0 -- 2.30.2