From b7a5b0843812b7bd4a225951ce11e7d14398395c Mon Sep 17 00:00:00 2001 From: Philippe De Muyter Date: Wed, 19 Feb 2014 17:21:59 +0100 Subject: [PATCH] net: phy: micrel: add support for KSZ8895 switch in SMI mode This patch adds a phy driver for the Micrel KSZ8895 switch. As the SoC MAC is directly connected to the switch MAC the link to the switch is always up. But the KSZ8895 switch can be hardwired in three configuration modes : - not configurable with eventually an eeprom-stored configuration - configurable by the mdio/mdc connection (SMI protocol) - configurable by a SPI connection. In not configurable mode, the switch starts automatically, but in the other modes, it must be started programmatically, by writing 1 in configuration register 1. We only support the not configurable and mdio/mdc (aka SMI) modes here. Signed-off-by: Philippe De Muyter Cc: Christian Gmeiner Signed-off-by: Joe Hershberger --- drivers/net/phy/micrel.c | 58 ++++++++++++++++++++++++++++++++++++++++ 1 file changed, 58 insertions(+) diff --git a/drivers/net/phy/micrel.c b/drivers/net/phy/micrel.c index 507b9a368b..1815b2900d 100644 --- a/drivers/net/phy/micrel.c +++ b/drivers/net/phy/micrel.c @@ -22,6 +22,63 @@ static struct phy_driver KSZ804_driver = { .shutdown = &genphy_shutdown, }; +/** + * KSZ8895 + */ + +static unsigned short smireg_to_phy(unsigned short reg) +{ + return ((reg & 0xc0) >> 3) + 0x06 + ((reg & 0x20) >> 5); +} + +static unsigned short smireg_to_reg(unsigned short reg) +{ + return reg & 0x1F; +} + +static void ksz8895_write_smireg(struct phy_device *phydev, int smireg, int val) +{ + phydev->bus->write(phydev->bus, smireg_to_phy(smireg), MDIO_DEVAD_NONE, + smireg_to_reg(smireg), val); +} + +#if 0 +static int ksz8895_read_smireg(struct phy_device *phydev, int smireg) +{ + return phydev->bus->read(phydev->bus, smireg_to_phy(smireg), + MDIO_DEVAD_NONE, smireg_to_reg(smireg)); +} +#endif + +int ksz8895_config(struct phy_device *phydev) +{ + /* we are connected directly to the switch without + * dedicated PHY. SCONF1 == 001 */ + phydev->link = 1; + phydev->duplex = DUPLEX_FULL; + phydev->speed = SPEED_100; + + /* Force the switch to start */ + ksz8895_write_smireg(phydev, 1, 1); + + return 0; +} + +static int ksz8895_startup(struct phy_device *phydev) +{ + return 0; +} + +static struct phy_driver ksz8895_driver = { + .name = "Micrel KSZ8895/KSZ8864", + .uid = 0x221450, + .mask = 0xffffe1, + .features = PHY_BASIC_FEATURES, + .config = &ksz8895_config, + .startup = &ksz8895_startup, + .shutdown = &genphy_shutdown, +}; + #ifndef CONFIG_PHY_MICREL_KSZ9021 /* * I can't believe Micrel used the exact same part number @@ -221,5 +278,6 @@ int phy_micrel_init(void) phy_register(&KS8721_driver); #endif phy_register(&ksz9031_driver); + phy_register(&ksz8895_driver); return 0; } -- 2.30.2