From b37f3def8690f8b81e2fb058a130358514bf2f93 Mon Sep 17 00:00:00 2001 From: Shiji Yang Date: Tue, 24 Sep 2024 19:15:56 +0800 Subject: [PATCH] ipq40xx: add support for SKSpruce WIA3300-20 Specification ------------- - SoC : Qualcomm IPQ4019 - RAM : 256 MiB DDR3 (NT5CC128M16JR-EK) - Flash : 64 MiB SPI NOR (Winbond W25Q512JVFQ) - WLAN : IPQ4019 built-in - 2.4 GHz : 2x2 MIMO WiFi4 - 5 GHz : 2x2 MIMO WiFi5 - Ethernet : QCA8075 10/100/1000 Mbps 1x WAN (ETH1, PoE); 1x LAN (ETH2) - USB : 1x 2.0 Type-A - UART : 3.3V, 115200n8 - Buttons : 1x Reset - LEDs : 1x RUN (lime & red) 1x WiFi 2.4 GHz (lime) 1x WiFi 5 GHz (lime) 2x ETH (lime), controlled by the QCA8075 phy - Power : DC 12V & 802.3at PoE - FCC ID : 2AHKT-WIA3300-20 - TFTP IP : - client : 192.168.18.254 - router : 192.168.18.1 Installation ------------ 1. Open uart console and start TFTP server. Copy initramfs image to the TFTP root directory and rename it to 'ipqinitramfs.bin'. 2. Power on and press 'Enter' to exit to the u-boot console according to the TTL log prompt. 3. Execute commands to load the initramfs image: tftpboot && bootm 4. Enter into OpenWrt to backup the partitions if you want to restore the stock firmware one day. 5. Override default 'bootcmd' environment variable in u-boot console: env set bootcmd 'sf probe && sf read $loadaddr 0x980000 0x800000 && bootm $loadaddr' env save 6. Repeat step 3 and flash 'sysupgrade' image in OpenWrt. Recovery and return to stock ---------------------------- 1. Restore the backup firmware partitions in the installation step 4. 2. Restore `bootcmd` environment variable via commands: env set bootcmd bootipq && env save MAC addresses ------------- +---------+-------------------+ | | MAC example | +---------+-------------------+ | LABEL | xx:xx:xx:xx:xx:25 | | LAN | xx:xx:xx:xx:xx:26 | | WAN | xx:xx:xx:xx:xx:25 | | WLAN 2g | xx:xx:xx:xx:xx:28 | | WLAN 5g | xx:xx:xx:xx:xx:29 | +---------+-------------------+ Notice ----------- 1. Some CH340 USB-TTL module doesn't work on this device. 2. The 'firmware' partition consists of four parts in the vendor layout: * Name Start Size * rootfs 0x980000 0x1680000 * 0:HLOS1 0x2000000 0x800000 * rootfs_1 0x2800000 0x1400000 * rootfs_data 0x3c00000 0x350000 3. User can control the USB power supply via commands: echo enabled > /sys/devices/platform/output-usb-power/state echo disabled > /sys/devices/platform/output-usb-power/state Signed-off-by: Shiji Yang Link: https://github.com/openwrt/openwrt/pull/16476 Signed-off-by: Robert Marko --- .../ipq40xx/base-files/etc/board.d/02_network | 3 + .../boot/dts/qcom/qcom-ipq4019-wia3300-20.dts | 446 ++++++++++++++++++ target/linux/ipq40xx/image/generic.mk | 13 + 3 files changed, 462 insertions(+) create mode 100644 target/linux/ipq40xx/files-6.6/arch/arm/boot/dts/qcom/qcom-ipq4019-wia3300-20.dts diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network index 7a2874a6e4..e3a6e24228 100644 --- a/target/linux/ipq40xx/base-files/etc/board.d/02_network +++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network @@ -117,6 +117,9 @@ ipq40xx_setup_interfaces() qxwlan,e2600ac-c2) ucidef_set_interfaces_lan_wan "sw-eth1 sw-eth2" "sw-eth3" ;; + skspruce,wia3300-20) + ucidef_set_interfaces_lan_wan "ETH2" "ETH1" + ;; zte,mf286d) ucidef_set_interfaces_lan_wan "lan2 lan3 lan4" "wan" ;; diff --git a/target/linux/ipq40xx/files-6.6/arch/arm/boot/dts/qcom/qcom-ipq4019-wia3300-20.dts b/target/linux/ipq40xx/files-6.6/arch/arm/boot/dts/qcom/qcom-ipq4019-wia3300-20.dts new file mode 100644 index 0000000000..cb7d3a918f --- /dev/null +++ b/target/linux/ipq40xx/files-6.6/arch/arm/boot/dts/qcom/qcom-ipq4019-wia3300-20.dts @@ -0,0 +1,446 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qcom-ipq4019.dtsi" +#include +#include +#include +#include + +/ { + compatible = "skspruce,wia3300-20", "qcom,ipq4019"; + model = "SKSpruce WIA3300-20"; + + aliases { + label-mac-device = &gmac; + led-boot = &led_status_red; + led-failsafe = &led_status_lime; + led-running = &led_status_lime; + led-upgrade = &led_status_red; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + keys { + compatible = "gpio-keys"; + + pinctrl-0 = <&key_pins>; + pinctrl-names = "default"; + + reset { + label = "reset"; + gpios = <&tlmm 18 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + + pinctrl-0 = <&led_pins>; + pinctrl-names = "default"; + + led_status_red: led-0 { + color = ; + function = LED_FUNCTION_STATUS; + gpios = <&tlmm 8 GPIO_ACTIVE_LOW>; + }; + + led_status_lime: led-1 { + color = ; + function = LED_FUNCTION_STATUS; + gpios = <&tlmm 9 GPIO_ACTIVE_LOW>; + }; + + led-2 { + color = ; + function = LED_FUNCTION_WLAN_2GHZ; + gpios = <&tlmm 11 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + + led-3 { + color = ; + function = LED_FUNCTION_WLAN_5GHZ; + gpios = <&tlmm 28 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy1tpt"; + }; + }; + + output-usb-power { + compatible = "regulator-output"; + vout-supply = <®_usb>; + }; + + reg_usb: regulator-usb { + compatible = "regulator-fixed"; + + pinctrl-0 = <®_usb_pins>; + pinctrl-names = "default"; + + enable-active-high; + gpios = <&tlmm 25 GPIO_ACTIVE_HIGH>; + regulator-max-microvolt = <5000000>; + regulator-min-microvolt = <5000000>; + regulator-name = "reg_usb"; + regulator-boot-on; + }; + + soc { + tcsr@1949000 { + compatible = "qcom,tcsr"; + reg = <0x1949000 0x100>; + qcom,wifi_glb_cfg = ; + }; + + tcsr@194b000 { + compatible = "qcom,tcsr"; + reg = <0x194b000 0x100>; + qcom,usb-hsphy-mode-select = ; + }; + + ess_tcsr@1953000 { + compatible = "qcom,tcsr"; + reg = <0x1953000 0x1000>; + qcom,ess-interface-select = ; + }; + + tcsr@1957000 { + compatible = "qcom,tcsr"; + reg = <0x1957000 0x100>; + qcom,wifi_noc_memtype_m0_m2 = ; + }; + }; +}; + +&blsp_dma { + status = "okay"; +}; + +&blsp1_spi1 { + status = "okay"; + + pinctrl-0 = <&spi0_pins>; + pinctrl-names = "default"; + + cs-gpios = <&tlmm 12 GPIO_ACTIVE_LOW>; + + flash@0 { + compatible = "jedec,spi-nor"; + spi-max-frequency = <24000000>; + reg = <0>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "0:SBL1"; + reg = <0x00000000 0x00040000>; + read-only; + }; + + partition@40000 { + label = "0:MIBIB"; + reg = <0x00040000 0x00020000>; + read-only; + }; + + partition@60000 { + label = "0:QSEE"; + reg = <0x00060000 0x00060000>; + read-only; + }; + + partition@c0000 { + label = "0:CDT"; + reg = <0x000c0000 0x00010000>; + read-only; + }; + + partition@d0000 { + label = "0:DDRPARAMS"; + reg = <0x000d0000 0x00010000>; + read-only; + }; + + partition@e0000 { + compatible = "u-boot,env"; + label = "0:APPSBLENV"; + reg = <0x000e0000 0x00010000>; + }; + + partition@f0000 { + label = "0:APPSBL"; + reg = <0x000f0000 0x00080000>; + read-only; + }; + + partition@170000 { + label = "0:oldART"; + reg = <0x00170000 0x00010000>; + read-only; + }; + + partition@180000 { + label = "0:HLOS"; + reg = <0x00180000 0x00800000>; + read-only; + }; + + partition@980000 { + compatible = "denx,fit"; + label = "firmware"; + reg = <0x980000 0x35d0000>; + }; + + partition@3f50000 { + label = "0:APPSBL1"; + reg = <0x03f50000 0x00080000>; + read-only; + }; + + partition@3fd0000 { + label = "BoardInfo"; + reg = <0x03fd0000 0x00010000>; + read-only; + + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_boardinfo_108a: macaddr@108a { + compatible = "mac-base"; + reg = <0x108a 0x6>; + #nvmem-cell-cells = <1>; + }; + }; + }; + + partition@3fe0000 { + label = "RebootCause"; + reg = <0x03fe0000 0x00010000>; + read-only; + }; + + partition@3ff0000 { + label = "0:ART"; + reg = <0x03ff0000 0x00010000>; + read-only; + + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + precal_art_1000: precal@1000 { + reg = <0x1000 0x2f20>; + }; + + precal_art_5000: precal@5000 { + reg = <0x5000 0x2f20>; + }; + }; + }; + }; + }; +}; + +&blsp1_uart1 { + status = "okay"; + + pinctrl-0 = <&serial0_pins>; + pinctrl-names = "default"; +}; + +&crypto { + status = "okay"; +}; + +&cryptobam { + status = "okay"; +}; + +ðphy3 { + leds { + #address-cells = <1>; + #size-cells = <0>; + + led@1 { + reg = <1>; + color = ; + function = LED_FUNCTION_LAN; + }; + }; +}; + +ðphy4 { + leds { + #address-cells = <1>; + #size-cells = <0>; + + led@1 { + reg = <1>; + color = ; + function = LED_FUNCTION_WAN; + }; + }; +}; + +&gmac { + status = "okay"; + + nvmem-cells = <&macaddr_boardinfo_108a 0>; + nvmem-cell-names = "mac-address"; +}; + +&mdio { + status = "okay"; + + pinctrl-0 = <&mdio_pins>; + pinctrl-names = "default"; + + reset-delay-us = <2000>; + reset-post-delay-us = <2000>; + reset-gpios = <&tlmm 43 GPIO_ACTIVE_LOW>; +}; + +&prng { + status = "okay"; +}; + +&qpic_bam { + status = "okay"; +}; + +&switch { + status = "okay"; +}; + +&swport4 { + status = "okay"; + + label = "ETH2"; + nvmem-cells = <&macaddr_boardinfo_108a 1>; + nvmem-cell-names = "mac-address"; +}; + +&swport5 { + status = "okay"; + + label = "ETH1"; + nvmem-cells = <&macaddr_boardinfo_108a 0>; + nvmem-cell-names = "mac-address"; +}; + +&tlmm { + key_pins: key_pinmux { + gpio { + pins = "gpio18"; + function = "gpio"; + bias-disable; + }; + }; + + led_pins: led_pinmux { + gpio { + pins = "gpio8", "gpio9", "gpio11", "gpio28"; + function = "gpio"; + drive-strength = <8>; + drive-open-drain; + bias-disable; + }; + }; + + mdio_pins: mdio_pinmux { + gpio { + pins = "gpio43"; + function = "gpio"; + drive-strength = <4>; + bias-disable; + output-high; + }; + + mdc { + pins = "gpio7"; + function = "mdc"; + drive-strength = <4>; + bias-disable; + }; + + mdio { + pins = "gpio6"; + function = "mdio"; + drive-strength = <4>; + drive-open-drain; + bias-pull-up; + }; + }; + + reg_usb_pins: reg_usb_pinmux { + gpio { + pins = "gpio25"; + function = "gpio"; + drive-strength = <8>; + bias-disable; + output-high; + }; + }; + + serial0_pins: serial0_pinmux { + blsp_uart0 { + pins = "gpio16", "gpio17"; + function = "blsp_uart0"; + drive-strength = <8>; + bias-disable; + }; + }; + + spi0_pins: spi0_pinmux { + blsp_spi0 { + pins = "gpio13", "gpio14", "gpio15"; + function = "blsp_spi0"; + drive-strength = <4>; + bias-disable; + }; + + gpio { + pins = "gpio12"; + function = "gpio"; + drive-strength = <4>; + bias-disable; + output-high; + }; + }; +}; + +&usb2 { + status = "okay"; +}; + +&usb2_hs_phy { + status = "okay"; +}; + +&watchdog { + status = "okay"; +}; + +&wifi0 { + status = "okay"; + + nvmem-cell-names = "mac-address", "pre-calibration"; + nvmem-cells = <&macaddr_boardinfo_108a 3>, <&precal_art_1000>; + qcom,ath10k-calibration-variant = "SKSpruce_WIA3300-20"; +}; + +&wifi1 { + status = "okay"; + + nvmem-cell-names = "mac-address", "pre-calibration"; + nvmem-cells = <&macaddr_boardinfo_108a 4>, <&precal_art_5000>; + qcom,ath10k-calibration-variant = "SKSpruce_WIA3300-20"; +}; diff --git a/target/linux/ipq40xx/image/generic.mk b/target/linux/ipq40xx/image/generic.mk index a2931ff01e..b5d387b14a 100644 --- a/target/linux/ipq40xx/image/generic.mk +++ b/target/linux/ipq40xx/image/generic.mk @@ -1092,6 +1092,19 @@ define Device/qxwlan_e2600ac-c2 endef TARGET_DEVICES += qxwlan_e2600ac-c2 +define Device/skspruce_wia3300-20 + $(call Device/FitImage) + BLOCKSIZE := 64k + IMAGE_SIZE := 55104k + SOC := qcom-ipq4019 + DEVICE_VENDOR := SKSpruce + DEVICE_MODEL := WIA3300-20 + DEVICE_PACKAGES := -ath10k-board-qca4019 ipq-wifi-skspruce_wia3300-20 + IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \ + append-rootfs | pad-rootfs | check-size | append-metadata +endef +TARGET_DEVICES +=skspruce_wia3300-20 + define Device/sony_ncp-hg100-cellular $(call Device/FitImage) DEVICE_VENDOR := Sony -- 2.30.2