From affe633be4c8122835e255425418ba1680a652e3 Mon Sep 17 00:00:00 2001 From: Daniel Danzberger Date: Fri, 1 Nov 2019 12:27:13 +0100 Subject: [PATCH] ipq40xx: ipq4019: Add new device Compex WPJ419 This device contains 2 flash devices. One NOR (32M) and one NAND (128M). U-boot and caldata are on the NOR, the firmware on the NAND. SoC: IPQ4019 CPU: 4x 710MHz ARMv7 RAM: 256MB FLASH: NOR:32MB NAND:128MB ETH: 2x GMAC Gigabit POE: 802.3 af/at POE, IEEE802.3af/IEEE802.3at(48-56V) WIFI: 1x 2.4Ghz Atheros qca4019 2x2 MU-MIMO 1x 5.0Ghz Atheros qca4019 2x2 MU-MIMO USB: 1x 3.0 PCI: 1x Mini PCIe SIM: 1x Slot SD: 1x MicroSD slot BTN: Reset LED: - Power - Ethernet UART: 1x Serial Port 4 Pin Connector (UART) 1x Serial Port 6 Pin Connector (High Speed UART) POWER: 12V 2A Installation ------------ Initial flashing can only be done via u-boot using the following commands: tftpboot openwrt-ipq40xx-generic-compex_wpj419-squashfs-nand-factory.ubi nand erase.chip; nand write ${fileaddr} 0x0 ${filesize} res Signed-off-by: Daniel Danzberger --- .../ipq40xx/base-files/etc/board.d/02_network | 1 + .../etc/hotplug.d/firmware/11-ath10k-caldata | 2 + .../base-files/lib/upgrade/platform.sh | 3 + .../arch/arm/boot/dts/qcom-ipq4019-wpj419.dts | 374 ++++++++++++++++++ target/linux/ipq40xx/image/Makefile | 14 + .../901-arm-boot-add-dts-files.patch | 3 +- 6 files changed, 396 insertions(+), 1 deletion(-) create mode 100644 target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-wpj419.dts diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network index 25402b7eb4..dafd83234e 100755 --- a/target/linux/ipq40xx/base-files/etc/board.d/02_network +++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network @@ -48,6 +48,7 @@ ipq40xx_setup_interfaces() ucidef_set_interface_lan "eth0" ;; avm,fritzrepeater-3000|\ + compex,wpj419|\ compex,wpj428) ucidef_set_interface_lan "eth0 eth1" ;; diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 2336ef3c7b..d4e4cc49ec 100644 --- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -70,6 +70,7 @@ case "$FIRMWARE" in /usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") || \ /usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") ;; + compex,wpj419 |\ compex,wpj428 |\ engenius,eap1300 |\ openmesh,a42 |\ @@ -133,6 +134,7 @@ case "$FIRMWARE" in /usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") || \ /usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") ;; + compex,wpj419 |\ compex,wpj428 |\ engenius,eap1300 |\ openmesh,a42 |\ diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh index 3445f2b50f..96f865c67e 100644 --- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh @@ -73,6 +73,9 @@ platform_do_upgrade() { CI_KERNPART="linux" nand_do_upgrade "$1" ;; + compex,wpj419) + nand_do_upgrade "$1" + ;; linksys,ea6350v3 |\ linksys,ea8300) platform_do_upgrade_linksys "$1" diff --git a/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-wpj419.dts b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-wpj419.dts new file mode 100644 index 0000000000..b6eb99278b --- /dev/null +++ b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-wpj419.dts @@ -0,0 +1,374 @@ +/* Copyright (c) 2015, The Linux Foundation. All rights reserved. + * Copyright (c) 2019, Nguyen Dinh Phi + * + * Permission to use, copy, modify, and/or distribute this software for any + * purpose with or without fee is hereby granted, provided that the above + * copyright notice and this permission notice appear in all copies. + * + * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES + * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR + * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES + * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN + * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF + * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. + * + */ + +#include "qcom-ipq4019.dtsi" +#include +#include +#include + +/ { + model = "Compex WPJ419"; + compatible = "compex,wpj419", "qcom,ipq4019"; + + memory { + device_type = "memory"; + reg = <0x80000000 0x10000000>; + }; + + reserved-memory { + ranges; + rsvd1@87000000 { + /* Reserved for other subsystem */ + reg = <0x87000000 0x500000>; + no-map; + }; + wifi_dump@87500000 { + reg = <0x87500000 0x600000>; + no-map; + }; + + rsvd2@87B00000 { + /* Reserved for other subsystem */ + reg = <0x87B00000 0x500000>; + no-map; + }; + }; + + chosen { + bootargs-append = " ubi.mtd=ubi root=/dev/ubiblock0_1 clk_ignore_unused"; + }; + + soc { + pinctrl@1000000 { + mdio_pins: mdio_pinmux { + mux_1 { + pins = "gpio6"; + function = "mdio"; + bias-pull-up; + }; + + mux_2 { + pins = "gpio7"; + function = "mdc"; + bias-pull-up; + }; + }; + + serial_0_pins: serial_pinmux { + mux { + pins = "gpio16", "gpio17"; + function = "blsp_uart0"; + bias-disable; + }; + }; + + serial_1_pins: serial1_pinmux { + mux { + pins = "gpio8", "gpio9", "gpio10", "gpio11"; + function = "blsp_uart1"; + bias-disable; + }; + }; + + spi_0_pins: spi_0_pinmux { + pinmux { + function = "blsp_spi0"; + pins = "gpio13", "gpio14", "gpio15"; + bias-disable; + }; + + pinmux_cs { + function = "gpio"; + pins = "gpio12"; + bias-disable; + output-high; + }; + }; + + i2c_0_pins: i2c_0_pinmux { + mux { + pins = "gpio20", "gpio21"; + function = "blsp_i2c0"; + bias-disable; + }; + }; + + nand_pins: nand_pins { + pullups { + pins = "gpio52", "gpio53", "gpio58", "gpio59"; + function = "qpic"; + bias-pull-up; + }; + + pulldowns { + pins = "gpio54", "gpio55", "gpio56", + "gpio57", "gpio60", "gpio61", + "gpio62", "gpio63", "gpio64", + "gpio65", "gpio66", "gpio67", + "gpio68", "gpio69"; + function = "qpic"; + bias-pull-down; + }; + }; + + led_0_pins: led0_pinmux { + mux_1 { + pins = "gpio36"; + function = "led0"; + bias-pull-down; + }; + mux_2 { + pins = "gpio40"; + function = "led4"; + bias-pull-down; + }; + }; + }; + + blsp_dma: dma@7884000 { + status = "okay"; + }; + + spi_0: spi@78b5000 { + pinctrl-0 = <&spi_0_pins>; + pinctrl-names = "default"; + status = "okay"; + cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>, <&tlmm 41 GPIO_ACTIVE_HIGH>; + num-cs = <2>; + + flash0@0 { + #address-cells = <1>; + #size-cells = <1>; + reg = <0>; + compatible = "jedec,spi-nor"; + spi-max-frequency = <24000000>; + broken-flash-reset; + + partitions { + compatible = "fixed-partitions"; + + partition@0 { + label = "0:SBL1"; + reg = <0x000000 0x040000>; + read-only; + }; + + partition@40000 { + label = "0:MIBIB"; + reg = <0x040000 0x020000>; + read-only; + }; + + partition@60000 { + label = "0:QSEE"; + reg = <0x060000 0x060000>; + read-only; + }; + + partition@c0000 { + label = "0:CDT"; + reg = <0x0c0000 0x010000>; + read-only; + }; + + partition@d0000 { + label = "0:DDRPARAMS"; + reg = <0x0d0000 0x010000>; + read-only; + }; + + partition@e0000 { + label = "u-boot-env"; + reg = <0x0e0000 0x010000>; + }; + + partition@f0000 { + label = "u-boot"; + reg = <0x0f0000 0x080000>; + read-only; + }; + + partition@170000 { + label = "0:ART"; + reg = <0x170000 0x010000>; + read-only; + }; + }; + }; + + nand@1 { + reg = <1>; + status = "okay"; + compatible = "spi-nand"; + spi-max-frequency = <24000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + /* The device has 128MB, but we can only address + * 64MB because of the bootloader's default settings. + * This is due to the old mt29f driver, + * which detected the deivce with only 64MB + */ + partition@0 { + label = "ubi"; + reg = <0x0000000 0x4000000>; + }; + }; + }; + }; + + mdio@90000 { + status = "okay"; + phy-reset-gpio = <&tlmm 47 0>; + pinctrl-0 = <&mdio_pins>; + pinctrl-names = "default"; + }; + + ess-psgmii@98000 { + status = "okay"; + }; + + tcsr@194b000 { + /* select hostmode */ + compatible = "qcom,tcsr"; + reg = <0x194b000 0x100>; + qcom,usb-hsphy-mode-select = ; + status = "okay"; + }; + + tcsr@1949000 { + compatible = "qcom,tcsr"; + reg = <0x1949000 0x100>; + qcom,wifi_glb_cfg = ; + }; + + ess_tcsr@1953000 { + compatible = "qcom,tcsr"; + reg = <0x1953000 0x1000>; + qcom,ess-interface-select = ; + }; + + tcsr@1957000 { + compatible = "qcom,tcsr"; + reg = <0x1957000 0x100>; + qcom,wifi_noc_memtype_m0_m2 = ; + }; + + i2c_0: i2c@78b7000 { + pinctrl-0 = <&i2c_0_pins>; + pinctrl-names = "default"; + status = "ok"; + }; + + serial@78af000 { + pinctrl-0 = <&serial_0_pins>; + pinctrl-names = "default"; + status = "okay"; + }; + + serial@78b0000 { + pinctrl-0 = <&serial_1_pins>; + pinctrl-names = "default"; + status = "okay"; + }; + + usb3_ss_phy: ssphy@9a000 { + status = "okay"; + }; + + usb3_hs_phy: hsphy@a6000 { + status = "okay"; + }; + + usb3: usb3@8af8800 { + status = "okay"; + }; + + usb2_hs_phy: hsphy@a8000 { + status = "okay"; + }; + + usb2: usb2@60f8800 { + status = "okay"; + }; + + cryptobam: dma@8e04000 { + status = "okay"; + }; + + crypto@8e3a000 { + status = "okay"; + }; + + watchdog@b017000 { + status = "okay"; + }; + + ess-switch@c000000 { + switch_lan_bmp = <0x1e>; + switch_wan_bmp = <0x20>; + status = "okay"; + }; + + edma@c080000 { + status = "okay"; + }; + + qpic_bam: dma@7984000 { + status = "okay"; + }; + + pcie0: pci@40000000 { + status = "okay"; + perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>; + wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>; + }; + + nand: qpic-nand@79b0000 { + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + status = "okay"; + }; + }; +}; + +&gmac0 { + qcom,phy_mdio_addr = <4>; + qcom,poll_required = <1>; + qcom,forced_speed = <1000>; + qcom,forced_duplex = <1>; + vlan_tag = <2 0x20>; +}; + +&gmac1 { + qcom,phy_mdio_addr = <3>; + qcom,poll_required = <1>; + qcom,forced_speed = <1000>; + qcom,forced_duplex = <1>; + vlan_tag = <1 0x10>; +}; + +&wifi0 { + status = "okay"; +}; + +&wifi1 { + status = "okay"; +}; diff --git a/target/linux/ipq40xx/image/Makefile b/target/linux/ipq40xx/image/Makefile index ed46bca649..ef80e68393 100644 --- a/target/linux/ipq40xx/image/Makefile +++ b/target/linux/ipq40xx/image/Makefile @@ -164,6 +164,20 @@ define Device/avm_fritzrepeater-3000 endef TARGET_DEVICES += avm_fritzrepeater-3000 +define Device/compex_wpj419 + $(call Device/FitImage) + $(call Device/UbiFit) + DEVICE_VENDOR := Compex + DEVICE_MODEL := WPJ419 + DEVICE_DTS := qcom-ipq4019-wpj419 + DEVICE_DTS_CONFIG := config@12 + KERNEL_INSTALL := 1 + BLOCKSIZE := 128k + PAGESIZE := 2048 + FILESYSTEMS := squashfs +endef +TARGET_DEVICES += compex_wpj419 + define Device/compex_wpj428 $(call Device/FitImage) DEVICE_VENDOR := Compex diff --git a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch index 2fe6e46966..4649b337e3 100644 --- a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -785,11 +785,35 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -785,11 +785,36 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ @@ -40,6 +40,7 @@ Signed-off-by: John Crispin + qcom-ipq4019-qxwlan-e2600ac-c1.dtb \ + qcom-ipq4019-qxwlan-e2600ac-c2.dtb \ + qcom-ipq4019-unielec-u4019-32m.dtb \ ++ qcom-ipq4019-wpj419.dtb \ + qcom-ipq4028-wpj428.dtb \ + qcom-ipq4029-gl-b1300.dtb \ + qcom-ipq4029-mr33.dtb \ -- 2.30.2