From abc7ed2c58860fc1363129efbe9e8c60f81a802c Mon Sep 17 00:00:00 2001 From: Weijie Gao Date: Sat, 29 Dec 2018 17:22:32 +0800 Subject: [PATCH] ath79: add support for D-Link DIR-859 A1 Hardware spec of DIR-859 A1: SoC: QCA9563 DRAM: 64MB DDR2 Flash: 16MB SPI-NOR Switch: QCA8337N WiFi 5.8GHz: QCA9880 USB is supported on the PCB but not connected. Flash instructions: 1. Upgrade the factory.bin through the factory web interface or the u-boot failsafe interface. The firmware will boot up correctly for the first time. Do not power off the device after OpenWrt has booted. Otherwise the u-boot will enter failsafe mode as the checksum of the firmware has been changed. 2. Upgrade the sysupgrade.bin in OpenWrt. After upgrading completes the u-boot won't complain about the firmware checksum and it's OK to use now. 3. If you powered off the device before upgrading the sysupgrade.bin, just upgrade the factory.bin through the u-boot failsafe interface and then goto step 2. Signed-off-by: Weijie Gao [squash commits, use common seama recipes, sync factory image recipe with ramips version] Signed-off-by: Mathias Kresin --- .../ath79/base-files/etc/board.d/01_leds | 3 + .../ath79/base-files/etc/board.d/02_network | 5 + .../etc/hotplug.d/firmware/10-ath9k-eeprom | 4 + .../etc/hotplug.d/firmware/11-ath10k-caldata | 4 + target/linux/ath79/config-4.14 | 1 + .../ath79/dts/qca9563_dlink_dir-859-a1.dts | 177 ++++++++++++++++++ target/linux/ath79/image/generic.mk | 29 +++ 7 files changed, 223 insertions(+) create mode 100644 target/linux/ath79/dts/qca9563_dlink_dir-859-a1.dts diff --git a/target/linux/ath79/base-files/etc/board.d/01_leds b/target/linux/ath79/base-files/etc/board.d/01_leds index 04c8964c9e..cc718b4d96 100755 --- a/target/linux/ath79/base-files/etc/board.d/01_leds +++ b/target/linux/ath79/base-files/etc/board.d/01_leds @@ -28,6 +28,9 @@ buffalo,whr-g301n) ucidef_set_led_switch "lan3" "LAN3" "$boardname:green:lan3" "switch0" "0x08" ucidef_set_led_switch "lan4" "LAN4" "$boardname:green:lan4" "switch0" "0x10" ;; +dlink,dir-859-a1) + ucidef_set_led_switch "internet" "WAN" "$boardname:green:internet" "switch0" "0x20" + ;; etactica,eg200) ucidef_set_led_netdev "lan" "LAN" "$boardname:red:eth0" "eth0" ucidef_set_led_oneshot "modbus" "Modbus" "$boardname:red:modbus" "100" "33" diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network index 004ab59573..1251048e08 100755 --- a/target/linux/ath79/base-files/etc/board.d/02_network +++ b/target/linux/ath79/base-files/etc/board.d/02_network @@ -158,6 +158,7 @@ ath79_setup_interfaces() ucidef_add_switch "switch0" \ "0@eth1" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "5:wan" "6@eth0" ;; + dlink,dir-859-a1|\ tplink,tl-wr1043nd-v4) ucidef_add_switch "switch0" \ "0@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "5:wan" @@ -234,6 +235,10 @@ ath79_setup_macs() lan_mac=$(mtd_get_mac_text "mac" 4) wan_mac=$(mtd_get_mac_text "mac" 24) ;; + dlink,dir-859-a1) + lan_mac=$(mtd_get_mac_ascii devdata "lanmac") + wan_mac=$(mtd_get_mac_ascii devdata "wanmac") + ;; elecom,wrc-300ghbk2-i) wan_mac=$(macaddr_add "$(mtd_get_mac_binary ART 4098)" -2) ;; diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom b/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom index f6ff582150..2da9250ddf 100644 --- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom +++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom @@ -105,6 +105,10 @@ case "$FIRMWARE" in ath9k_eeprom_extract "art" 4096 1088 ath9k_patch_fw_mac_crc $(mtd_get_mac_text "mac" 4) 2 ;; + dlink,dir-859-a1) + ath9k_eeprom_extract "art" 4096 1088 + ath9k_patch_fw_mac $(mtd_get_mac_ascii devdata "wlan24mac") 2 + ;; iodata,wn-ac1167dgr|\ iodata,wn-ac1600dgr2|\ iodata,wn-ag300dgr) diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 53f57be824..b9a987d418 100644 --- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -92,6 +92,10 @@ case "$FIRMWARE" in ath10kcal_extract "art" 20480 2116 ath10kcal_patch_mac_crc $(macaddr_add $(mtd_get_mac_binary art 0) -1) ;; + dlink,dir-859-a1) + ath10kcal_extract "art" 20480 2116 + ath10kcal_patch_mac $(mtd_get_mac_ascii devdata "wlan5mac") + ;; glinet,gl-x750) ath10kcal_extract "art" 20480 2116 ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +1) diff --git a/target/linux/ath79/config-4.14 b/target/linux/ath79/config-4.14 index 969136ddde..5a2c685d40 100644 --- a/target/linux/ath79/config-4.14 +++ b/target/linux/ath79/config-4.14 @@ -168,6 +168,7 @@ CONFIG_MTD_PHYSMAP=y CONFIG_MTD_SPI_NOR=y CONFIG_MTD_SPLIT_FIRMWARE=y CONFIG_MTD_SPLIT_LZMA_FW=y +CONFIG_MTD_SPLIT_SEAMA_FW=y CONFIG_MTD_SPLIT_TPLINK_FW=y CONFIG_MTD_SPLIT_UIMAGE_FW=y CONFIG_MTD_TPLINK_PARTS=y diff --git a/target/linux/ath79/dts/qca9563_dlink_dir-859-a1.dts b/target/linux/ath79/dts/qca9563_dlink_dir-859-a1.dts new file mode 100644 index 0000000000..23b4cc5126 --- /dev/null +++ b/target/linux/ath79/dts/qca9563_dlink_dir-859-a1.dts @@ -0,0 +1,177 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include +#include + +#include "qca956x.dtsi" + +/ { + model = "D-Link DIR-859 A1"; + compatible = "dlink,dir-859-a1", "qca,qca9563"; + + aliases { + led-boot = &power; + led-failsafe = &power; + led-running = &power; + led-upgrade = &power; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + leds { + compatible = "gpio-leds"; + + wps { + label = "dir-859-a1:green:wps"; + gpios = <&gpio 8 GPIO_ACTIVE_LOW>; + }; + + power: power { + label = "dir-859-a1:green:power"; + gpios = <&gpio 15 GPIO_ACTIVE_LOW>; + }; + + internet { + label = "dir-859-a1:green:internet"; + gpios = <&gpio 16 GPIO_ACTIVE_LOW>; + }; + + wlan { + label = "dir-859-a1:green:wlan"; + gpios = <&gpio 19 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + }; + + keys { + compatible = "gpio-keys-polled"; + poll-interval = <20>; + + wps { + linux,code = ; + gpios = <&gpio 1 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + + reset { + linux,code = ; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + }; + + gpio-export { + compatible = "gpio-export"; + #size-cells = <0>; + + gpio_switch_reset { + gpio-export,name = "dir-859-a1:reset:switch"; + gpio-export,output = <1>; + gpios = <&gpio 11 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&uart { + status = "okay"; +}; + +&gpio { + status = "okay"; +}; + +&pcie { + status = "okay"; +}; + +&spi { + num-cs = <1>; + + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <30000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "bootloader"; + reg = <0x000000 0x40000>; + read-only; + }; + + partition@40000 { + label = "bdcfg"; + reg = <0x040000 0x10000>; + read-only; + }; + + partition@50000 { + label = "devdata"; + reg = <0x050000 0x10000>; + read-only; + }; + + partition@60000 { + label = "devconf"; + reg = <0x060000 0x10000>; + read-only; + }; + + partition@70000 { + compatible = "seama"; + label = "firmware"; + reg = <0x070000 0xf80000>; + }; + + art: partition@ff0000 { + label = "art"; + reg = <0xff0000 0x010000>; + read-only; + }; + }; + }; +}; + +&mdio0 { + status = "okay"; + + phy-mask = <0>; + + phy0: ethernet-phy@0 { + reg = <0>; + phy-mode = "sgmii"; + + qca,ar8327-initvals = < + 0x04 0x00080080 /* PORT0 PAD MODE CTRL */ + 0x10 0x81000080 /* POWER_ON_STRIP */ + 0x50 0xcc35cc35 /* LED_CTRL0 */ + 0x54 0xcb37cb37 /* LED_CTRL1 */ + 0x58 0x00000000 /* LED_CTRL2 */ + 0x5c 0x00f3cf00 /* LED_CTRL3 */ + 0x7c 0x0000007e /* PORT0_STATUS */ + >; + }; +}; + +ð0 { + status = "okay"; + + pll-data = <0x03000101 0x00000101 0x00001919>; + + phy-mode = "sgmii"; + phy-handle = <&phy0>; +}; + +&wmac { + status = "okay"; + qca,no-eeprom; +}; diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk index b2f83ba58c..8dd5dab7ca 100644 --- a/target/linux/ath79/image/generic.mk +++ b/target/linux/ath79/image/generic.mk @@ -2,6 +2,7 @@ include ./common-buffalo.mk include ./common-netgear.mk DEVICE_VARS += ADDPATTERN_ID ADDPATTERN_VERSION +DEVICE_VARS += SEAMA_SIGNATURE SEAMA_MTDBLOCK define Build/cybertan-trx @echo -n '' > $@-empty.bin @@ -53,6 +54,23 @@ define Build/nec-fw mv $@.new $@ endef +define Device/seama + KERNEL := kernel-bin | append-dtb | relocate-kernel | lzma + KERNEL_INITRAMFS := $$(KERNEL) | seama + IMAGES += factory.bin + SEAMA_MTDBLOCK := 1 + + # 64 bytes offset: + # - 28 bytes seama_header + # - 36 bytes of META data (4-bytes aligned) + IMAGE/default := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | append-rootfs + IMAGE/sysupgrade.bin := \ + $$(IMAGE/default) | seama | pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE) + IMAGE/factory.bin := \ + $$(IMAGE/default) | pad-rootfs -x 64 | seama | seama-seal | check-size $$$$(IMAGE_SIZE) + SEAMA_SIGNATURE := +endef + define Device/avm_fritz300e ATH_SOC := ar7242 DEVICE_TITLE := AVM FRITZ!WLAN Repeater 300E @@ -192,6 +210,17 @@ define Device/dlink_dir-835-a1 endef TARGET_DEVICES += dlink_dir-835-a1 +define Device/dlink_dir-859-a1 + $(Device/seama) + ATH_SOC := qca9563 + DEVICE_TITLE := D-LINK DIR-859 A1 + IMAGE_SIZE := 15872k + DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct + SEAMA_SIGNATURE := wrgac37_dlink.2013gui_dir859 + SUPPORTED_DEVICES += dir-859-a1 +endef +TARGET_DEVICES += dlink_dir-859-a1 + define Device/elecom_wrc-300ghbk2-i ATH_SOC := qca9563 DEVICE_TITLE := ELECOM WRC-300GHBK2-I -- 2.30.2