From a6b93e6555a6ecd0d08b0383ea4d93d09a168187 Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Thu, 30 Apr 2020 18:03:58 +0200 Subject: [PATCH] docs: networking: convert ltpc.txt to ReST - add SPDX header; - add a document title; - mark code blocks and literals as such; - mark tables as such; - adjust identation, whitespaces and blank lines; - add to networking/index.rst. Signed-off-by: Mauro Carvalho Chehab Signed-off-by: David S. Miller --- Documentation/networking/index.rst | 1 + .../networking/{ltpc.txt => ltpc.rst} | 45 ++++++++++++------- drivers/net/appletalk/Kconfig | 2 +- 3 files changed, 31 insertions(+), 17 deletions(-) rename Documentation/networking/{ltpc.txt => ltpc.rst} (86%) diff --git a/Documentation/networking/index.rst b/Documentation/networking/index.rst index acd2567cf0d4..b3608b177a8b 100644 --- a/Documentation/networking/index.rst +++ b/Documentation/networking/index.rst @@ -76,6 +76,7 @@ Contents: kcm l2tp lapb-module + ltpc .. only:: subproject and html diff --git a/Documentation/networking/ltpc.txt b/Documentation/networking/ltpc.rst similarity index 86% rename from Documentation/networking/ltpc.txt rename to Documentation/networking/ltpc.rst index a005a73b76d0..0ad197fd17ce 100644 --- a/Documentation/networking/ltpc.txt +++ b/Documentation/networking/ltpc.rst @@ -1,3 +1,9 @@ +.. SPDX-License-Identifier: GPL-2.0 + +=========== +LTPC Driver +=========== + This is the ALPHA version of the ltpc driver. In order to use it, you will need at least version 1.3.3 of the @@ -15,7 +21,7 @@ yourself. (see "Card Configuration" below for how to determine or change the settings on your card) When the driver is compiled into the kernel, you can add a line such -as the following to your /etc/lilo.conf: +as the following to your /etc/lilo.conf:: append="ltpc=0x240,9,1" @@ -25,13 +31,13 @@ the driver will try to determine them itself. If you load the driver as a module, you can pass the parameters "io=", "irq=", and "dma=" on the command line with insmod or modprobe, or add -them as options in a configuration file in /etc/modprobe.d/ directory: +them as options in a configuration file in /etc/modprobe.d/ directory:: alias lt0 ltpc # autoload the module when the interface is configured options ltpc io=0x240 irq=9 dma=1 Before starting up the netatalk demons (perhaps in rc.local), you -need to add a line such as: +need to add a line such as:: /sbin/ifconfig lt0 127.0.0.42 @@ -42,7 +48,7 @@ The appropriate netatalk configuration depends on whether you are attached to a network that includes AppleTalk routers or not. If, like me, you are simply connecting to your home Macintoshes and printers, you need to set up netatalk to "seed". The way I do this -is to have the lines +is to have the lines:: dummy -seed -phase 2 -net 2000 -addr 2000.26 -zone "1033" lt0 -seed -phase 1 -net 1033 -addr 1033.27 -zone "1033" @@ -57,13 +63,13 @@ such. If you are attached to an extended AppleTalk network, with routers on it, then you don't need to fool around with this -- the appropriate -line in atalkd.conf is +line in atalkd.conf is:: lt0 -phase 1 --------------------------------------- -Card Configuration: +Card Configuration +================== The interrupts and so forth are configured via the dipswitch on the board. Set the switches so as not to conflict with other hardware. @@ -73,26 +79,32 @@ board. Set the switches so as not to conflict with other hardware. original documentation refers to IRQ2. Since you'll be running this on an AT (or later) class machine, that really means IRQ9. + === =========================================================== SW1 IRQ 4 SW2 IRQ 3 SW3 IRQ 9 (2 in original card documentation only applies to XT) + === =========================================================== DMA -- choose DMA 1 or 3, and set both corresponding switches. + === ===== SW4 DMA 3 SW5 DMA 1 SW6 DMA 3 SW7 DMA 1 + === ===== I/O address -- choose one. + === ========= SW8 220 / 240 + === ========= --------------------------------------- -IP: +IP +== Yes, it is possible to do IP over LocalTalk. However, you can't just treat the LocalTalk device like an ordinary Ethernet device, even if @@ -102,9 +114,9 @@ Instead, you follow the same procedure as for doing IP in EtherTalk. See Documentation/networking/ipddp.rst for more information about the kernel driver and userspace tools needed. --------------------------------------- -BUGS: +Bugs +==== IRQ autoprobing often doesn't work on a cold boot. To get around this, either compile the driver as a module, or pass the parameters @@ -120,12 +132,13 @@ It may theoretically be possible to use two LTPC cards in the same machine, but this is unsupported, so if you really want to do this, you'll probably have to hack the initialization code a bit. -______________________________________ -THANKS: - Thanks to Alan Cox for helpful discussions early on in this +Thanks +====== + +Thanks to Alan Cox for helpful discussions early on in this work, and to Denis Hainsworth for doing the bleeding-edge testing. --- Bradford Johnson +Bradford Johnson --- Updated 11/09/1998 by David Huggins-Daines +Updated 11/09/1998 by David Huggins-Daines diff --git a/drivers/net/appletalk/Kconfig b/drivers/net/appletalk/Kconfig index ccde6479050c..10589a82263b 100644 --- a/drivers/net/appletalk/Kconfig +++ b/drivers/net/appletalk/Kconfig @@ -48,7 +48,7 @@ config LTPC If you are in doubt, this card is the one with the 65C02 chip on it. You also need version 1.3.3 or later of the netatalk package. This driver is experimental, which means that it may not work. - See the file . + See the file . config COPS tristate "COPS LocalTalk PC support" -- 2.30.2