From 8d67c3685e3b4bea8524e2e25b1443b62a69352b Mon Sep 17 00:00:00 2001 From: Shengzhou Liu Date: Wed, 5 Mar 2014 15:04:48 +0800 Subject: [PATCH] powerpc/t2080rdb: Add T2080PCIe-RDB board support T2080PCIe-RDB is a Freescale Reference Design Board that hosts the T2080 SoC. It works in two mode: standalone mode and PCIe endpoint mode. T2080PCIe-RDB Feature Overview ------------------------------ Processor: - T2080 SoC integrating four 64-bit dual-threads e6500 cores up to 1.8GHz DDR Memory: - Single memory controller capable of supporting DDR3 and DDR3-LP devices - 72bit 4GB DDR3-LP SODIMM in slot Ethernet interfaces: - Two 10M/100M/1G RGMII ports on-board - Two 10Gbps SFP+ ports on-board - Two 10Gbps Base-T ports on-board Accelerator: - DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC SerDes 16 lanes configuration: - SerDes-1 Lane A-B: to two 10G XFI fiber (MAC9 & MAC10) - SerDes-1 Lane C-D: to two 10G Base-T (MAC1 & MAC2) - SerDes-1 Lane E-H: to PCIe Goldfinger (PCIe4 x4, Gen3) - SerDes-2 Lane A-D: to PCIe Slot (PCIe1 x4, Gen2) - SerDes-2 Lane E-F: to C293 secure co-processor (PCIe2 x2) - SerDes-2 Lane G-H: to SATA1 & SATA2 IFC/Local Bus: - NOR: 128MB 16-bit NOR flash - NAND: 512MB 8-bit NAND flash - CPLD: for system controlling with programable header on-board eSPI: - 64MB N25Q512 SPI flash USB: - Two USB2.0 ports with internal PHY (both Type-A) PCIe: - One PCIe x4 gold-finger - One PCIe x4 connector - One PCIe x2 end-point device (C293 Crypto co-processor) SATA: - Two SATA 2.0 ports on-board SDHC: - support a TF-card on-board I2C: - Four I2C controllers. UART: - Dual 4-pins UART serial ports Signed-off-by: Shengzhou Liu Reviewed-by: York Sun --- board/freescale/t208xrdb/Makefile | 13 + board/freescale/t208xrdb/README | 208 +++++++ board/freescale/t208xrdb/cpld.c | 71 +++ board/freescale/t208xrdb/cpld.h | 42 ++ board/freescale/t208xrdb/ddr.c | 112 ++++ board/freescale/t208xrdb/ddr.h | 47 ++ board/freescale/t208xrdb/eth_t208xrdb.c | 106 ++++ board/freescale/t208xrdb/law.c | 34 ++ board/freescale/t208xrdb/pci.c | 23 + board/freescale/t208xrdb/t2080_pbi.cfg | 41 ++ board/freescale/t208xrdb/t2080_rcw.cfg | 8 + board/freescale/t208xrdb/t208xrdb.c | 124 ++++ board/freescale/t208xrdb/t208xrdb.h | 13 + board/freescale/t208xrdb/tlb.c | 151 +++++ boards.cfg | 5 + include/configs/T208xRDB.h | 779 ++++++++++++++++++++++++ 16 files changed, 1777 insertions(+) create mode 100644 board/freescale/t208xrdb/Makefile create mode 100644 board/freescale/t208xrdb/README create mode 100644 board/freescale/t208xrdb/cpld.c create mode 100644 board/freescale/t208xrdb/cpld.h create mode 100644 board/freescale/t208xrdb/ddr.c create mode 100644 board/freescale/t208xrdb/ddr.h create mode 100644 board/freescale/t208xrdb/eth_t208xrdb.c create mode 100644 board/freescale/t208xrdb/law.c create mode 100644 board/freescale/t208xrdb/pci.c create mode 100644 board/freescale/t208xrdb/t2080_pbi.cfg create mode 100644 board/freescale/t208xrdb/t2080_rcw.cfg create mode 100644 board/freescale/t208xrdb/t208xrdb.c create mode 100644 board/freescale/t208xrdb/t208xrdb.h create mode 100644 board/freescale/t208xrdb/tlb.c create mode 100644 include/configs/T208xRDB.h diff --git a/board/freescale/t208xrdb/Makefile b/board/freescale/t208xrdb/Makefile new file mode 100644 index 0000000000..092c9ff0dc --- /dev/null +++ b/board/freescale/t208xrdb/Makefile @@ -0,0 +1,13 @@ +# +# Copyright 2014 Freescale Semiconductor, Inc. +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-$(CONFIG_T2080RDB) += t208xrdb.o +obj-$(CONFIG_T2080RDB) += eth_t208xrdb.o +obj-$(CONFIG_T2080RDB) += cpld.o +obj-$(CONFIG_PCI) += pci.o +obj-y += ddr.o +obj-y += law.o +obj-y += tlb.o diff --git a/board/freescale/t208xrdb/README b/board/freescale/t208xrdb/README new file mode 100644 index 0000000000..0012c6cb40 --- /dev/null +++ b/board/freescale/t208xrdb/README @@ -0,0 +1,208 @@ +T2080PCIe-RDB is a Freescale Reference Design Board that hosts the T2080 SoC. +It can work in two mode: standalone mode and PCIe endpoint mode. + +T2080 SoC Overview +------------------ +The T2080 QorIQ multicore processor combines four dual-threaded e6500 Power +Architecture processor cores with high-performance datapath acceleration +logic and network and peripheral bus interfaces required for networking, +telecom/datacom, wireless infrastructure, and mil/aerospace applications. + +T2080 includes the following functions and features: + - Four dual-threads 64-bit Power architecture e6500 cores, up to 1.8GHz + - 2MB L2 cache and 512KB CoreNet platform cache (CPC) + - Hierarchical interconnect fabric + - One 32-/64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving + - Data Path Acceleration Architecture (DPAA) incorporating acceleration + - 16 SerDes lanes up to 10.3125 GHz + - 8 Ethernet interfaces, supporting combinations of the following: + - Up to four 10 Gbps Ethernet MACs + - Up to eight 1 Gbps Ethernet MACs + - Up to four 2.5 Gbps Ethernet MACs + - High-speed peripheral interfaces + - Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0 with SR-IOV) + - Two Serial RapidIO 2.0 controllers/ports running at up to 5 GHz + - Additional peripheral interfaces + - Two serial ATA (SATA 2.0) controllers + - Two high-speed USB 2.0 controllers with integrated PHY + - Enhanced secure digital host controller (SD/SDHC/SDXC/eMMC) + - Enhanced serial peripheral interface (eSPI) + - Four I2C controllers + - Four 2-pin UARTs or two 4-pin UARTs + - Integrated Flash Controller supporting NAND and NOR flash + - Three eight-channel DMA engines + - Support for hardware virtualization and partitioning enforcement + - QorIQ Platform's Trust Architecture 2.0 + +Differences between T2080 and T2081 +----------------------------------- + Feature T2080 T2081 + 1G Ethernet numbers: 8 6 + 10G Ethernet numbers: 4 2 + SerDes lanes: 16 8 + Serial RapidIO,RMan: 2 no + SATA Controller: 2 no + Aurora: yes no + SoC Package: 896-pins 780-pins + + +T2080PCIe-RDB board Overview +---------------------------- + - SERDES Configuration + - SerDes-1 Lane A-B: to two 10G XFI fiber (MAC9 & MAC10) + - SerDes-1 Lane C-D: to two 10G Base-T (MAC1 & MAC2) + - SerDes-1 Lane E-H: to PCIe Goldfinger (PCIe4 x4, Gen3) + - SerDes-2 Lane A-D: to PCIe Slot (PCIe1 x4, Gen2) + - SerDes-2 Lane E-F: to C293 secure co-processor (PCIe2 x2) + - SerDes-2 Lane G-H: to SATA1 & SATA2 + - Ethernet + - Two on-board 10M/100M/1G RGMII ethernet ports + - Two on-board 10Gbps XFI fiber ports + - Two on-board 10Gbps Base-T copper ports + - DDR Memory + - Supports 72bit 4GB DDR3-LP SODIMM + - PCIe + - One PCIe x4 gold-finger + - One PCIe x4 connector + - One PCIe x2 end-point device (C293 Crypto co-processor) + - IFC/Local Bus + - NOR: 128MB 16-bit NOR Flash + - NAND: 512MB 8-bit NAND flash + - CPLD: for system controlling with programable header on-board + - SATA + - Two SATA 2.0 onnectors on-board + - USB + - Supports two USB 2.0 ports with integrated PHYs + - Two type A ports with 5V@1.5A per port. + - SDHC + - one TF-card connector on-board + - SPI + - On-board 64MB SPI flash + - Other + - Two Serial ports + - Four I2C ports + + +System Memory map +----------------- +Start Address End Address Description Size +0xF_FFDF_0000 0xF_FFDF_0FFF IFC - CPLD 4KB +0xF_FF80_0000 0xF_FF80_FFFF IFC - NAND Flash 64KB +0xF_FE00_0000 0xF_FEFF_FFFF CCSRBAR 16MB +0xF_F803_0000 0xF_F803_FFFF PCI Express 4 I/O Space 64KB +0xF_F802_0000 0xF_F802_FFFF PCI Express 3 I/O Space 64KB +0xF_F801_0000 0xF_F801_FFFF PCI Express 2 I/O Space 64KB +0xF_F800_0000 0xF_F800_FFFF PCI Express 1 I/O Space 64KB +0xF_F600_0000 0xF_F7FF_FFFF Queue manager software portal 32MB +0xF_F400_0000 0xF_F5FF_FFFF Buffer manager software portal 32MB +0xF_E800_0000 0xF_EFFF_FFFF IFC - NOR Flash 128MB +0xF_0000_0000 0xF_003F_FFFF DCSR 4MB +0xC_4000_0000 0xC_4FFF_FFFF PCI Express 4 Mem Space 256MB +0xC_3000_0000 0xC_3FFF_FFFF PCI Express 3 Mem Space 256MB +0xC_2000_0000 0xC_2FFF_FFFF PCI Express 2 Mem Space 256MB +0xC_0000_0000 0xC_1FFF_FFFF PCI Express 1 Mem Space 512MB +0x0_0000_0000 0x0_ffff_ffff DDR 4GB + + +128M NOR Flash memory Map +------------------------- +Start Address End Address Definition Max size +0xEFF40000 0xEFFFFFFF u-boot (current bank) 768KB +0xEFF20000 0xEFF3FFFF u-boot env (current bank) 128KB +0xEFF00000 0xEFF1FFFF FMAN Ucode (current bank) 128KB +0xEFE00000 0xEFE3FFFF PHY CS4315 firmware 256KB +0xED300000 0xEFEFFFFF rootfs (alt bank) 44MB +0xEC800000 0xEC8FFFFF Hardware device tree (alt bank) 1MB +0xEC020000 0xEC7FFFFF Linux.uImage (alt bank) 7MB + 875KB +0xEC000000 0xEC01FFFF RCW (alt bank) 128KB +0xEBF40000 0xEBFFFFFF u-boot (alt bank) 768KB +0xEBF20000 0xEBF3FFFF u-boot env (alt bank) 128KB +0xEBF00000 0xEBF1FFFF FMAN ucode (alt bank) 128KB +0xEBE00000 0xEBE3FFFF PHY CS4315 firmware (alt bank) 256KB +0xE9300000 0xEBEFFFFF rootfs (current bank) 44MB +0xE8800000 0xE88FFFFF Hardware device tree (cur bank) 11MB + 512KB +0xE8020000 0xE86FFFFF Linux.uImage (current bank) 7MB + 875KB +0xE8000000 0xE801FFFF RCW (current bank) 128KB + + +T2080PCIe-RDB Ethernet Port Map +------------------------------- +Label In Uboot In Linux FMan Address Comments PHY +ETH0 FM1@GTEC1 fm1-mac9 0xfe4f0000 10G SFP+ (CS4315) +ETH1 FM1@GTEC2 fm1-mac10 0xfe4f2000 10G SFP+ (CS4315) +ETH2 FM1@GTEC3 fm1-mac1 0xfe4e0000 10G Base-T (AQ1202) +ETH3 FM1@GTEC4 fm1-mac2 0xfe4e2000 10G Base-T (AQ1202) +ETH4 FM1@DTSEC3 fm1-mac3 0xfe4e4000 1G RGMII (RTL8211E) +ETH5 FM1@DTSEC4 fm1-mac4 0xfe4e6000 1G RGMII (RTL8211E) + + +T2080PCIe-RDB Default DIP-Switch setting +---------------------------------------- +SW1[1:8] = '00010011' +SW2[1:8] = '10111111' +SW3[1:8] = '11100001' + +Software configurations and board settings +------------------------------------------ +1. NOR boot: + a. build NOR boot image + $ make T2080RDB + b. program u-boot.bin image to NOR flash + => tftp 1000000 u-boot.bin + => pro off all;era eff40000 efffffff;cp.b 1000000 eff40000 $filesize + set SW1[1:8] = '00010011', SW2[1] = '1', SW3[4] = '0' for NOR boot + + Switching between default bank and alternate bank on NOR flash + To change boot source to vbank4: + via software: run command 'cpld reset altbank' in u-boot. + via DIP-switch: set SW3[5:7] = '011' + + To change boot source to vbank0: + via software: run command 'cpld reset' in u-boot. + via DIP-Switch: set SW3[5:7] = '111' + +2. NAND Boot: + a. build PBL image for NAND boot + $ make T2080RDB_NAND_config + $ make u-boot.pbl + b. program u-boot.pbl to NAND flash + => tftp 1000000 u-boot.pbl + => nand erase 0 d0000 + => nand write 1000000 0 $filesize + set SW1[1:8] = '10000010', SW2[1] = '1', SW3[4] = '1' for NAND boot + +3. SPI Boot: + a. build PBL image for SPI boot + $ make T2080RDB_SPIFLASH_config + $ make u-boot.pbl + b. program u-boot.pbl to SPI flash + => tftp 1000000 u-boot.pbl + => sf probe 0 + => sf erase 0 d0000 + => sf write 1000000 0 $filesize + set SW1[1:8] = '00100010', SW2[1] ='1' for SPI boot + +4. SD Boot: + a. build PBL image for SD boot + $ make T2080RDB_SDCARD_config + $ make u-boot.pbl + b. program u-boot.pbl to TF card + => tftp 1000000 u-boot.pbl + => mmc write 1000000 8 1650 + set SW1[1:8] = '00100000', SW2[1] = '0' for SD boot + + +How to update the ucode of Cortina CS4315/CS4340 10G PHY +-------------------------------------------------------- +=> tftp 1000000 CS4315-CS4340-PHY-ucode.txt +=> pro off all;era 0xefe00000 0xefefffff;cp.b 1000000 0xefe00000 $filesize + + +How to update the ucode of Freescale FMAN +----------------------------------------- +=> tftp 1000000 fsl_fman_ucode_t2080_r1.0.bin +=> pro off all;erase 0xeff00000 0xeff1ffff;cp 1000000 0xeff00000 $filesize + + +For more details, please refer to T2080PCIe-RDB User Guide and access +website www.freescale.com and Freescale QorIQ SDK Infocenter document. diff --git a/board/freescale/t208xrdb/cpld.c b/board/freescale/t208xrdb/cpld.c new file mode 100644 index 0000000000..4aa126be54 --- /dev/null +++ b/board/freescale/t208xrdb/cpld.c @@ -0,0 +1,71 @@ +/* + * Copyright 2014 Freescale Semiconductor + * + * SPDX-License-Identifier: GPL-2.0+ + * + * Freescale T2080RDB board-specific CPLD controlling supports. + */ + +#include +#include +#include "cpld.h" + +u8 cpld_read(unsigned int reg) +{ + void *p = (void *)CONFIG_SYS_CPLD_BASE; + + return in_8(p + reg); +} + +void cpld_write(unsigned int reg, u8 value) +{ + void *p = (void *)CONFIG_SYS_CPLD_BASE; + + out_8(p + reg, value); +} + +/* Set the boot bank to the alternate bank */ +void cpld_set_altbank(void) +{ + u8 reg = CPLD_READ(flash_csr); + + reg = (reg & ~CPLD_BANK_SEL_MASK) | CPLD_LBMAP_ALTBANK; + CPLD_WRITE(flash_csr, reg); + CPLD_WRITE(reset_ctl, CPLD_LBMAP_RESET); +} + +/* Set the boot bank to the default bank */ +void cpld_set_defbank(void) +{ + u8 reg = CPLD_READ(flash_csr); + + reg = (reg & ~CPLD_BANK_SEL_MASK) | CPLD_LBMAP_DFLTBANK; + CPLD_WRITE(flash_csr, reg); + CPLD_WRITE(reset_ctl, CPLD_LBMAP_RESET); +} + +int do_cpld(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) +{ + int rc = 0; + + if (argc <= 1) + return cmd_usage(cmdtp); + + if (strcmp(argv[1], "reset") == 0) { + if (strcmp(argv[2], "altbank") == 0) + cpld_set_altbank(); + else + cpld_set_defbank(); + } else { + rc = cmd_usage(cmdtp); + } + + return rc; +} + +U_BOOT_CMD( + cpld, CONFIG_SYS_MAXARGS, 1, do_cpld, + "Reset the board or alternate bank", + "reset: reset to default bank\n" + "cpld reset altbank: reset to alternate bank\n" +); diff --git a/board/freescale/t208xrdb/cpld.h b/board/freescale/t208xrdb/cpld.h new file mode 100644 index 0000000000..4cee4e55cf --- /dev/null +++ b/board/freescale/t208xrdb/cpld.h @@ -0,0 +1,42 @@ +/* + * Copyright 2014 Freescale Semiconductor + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/* + * CPLD register set of T2080RDB board-specific. + */ +struct cpld_data { + u8 chip_id1; /* 0x00 - Chip ID1 register */ + u8 chip_id2; /* 0x01 - Chip ID2 register */ + u8 hw_ver; /* 0x02 - Hardware Revision Register */ + u8 sw_ver; /* 0x03 - Software Revision register */ + u8 res0[12]; /* 0x04 - 0x0F - not used */ + u8 reset_ctl; /* 0x10 - Reset control Register */ + u8 flash_csr; /* 0x11 - Flash control and status register */ + u8 thermal_csr; /* 0x12 - Thermal control and status register */ + u8 led_csr; /* 0x13 - LED control and status register */ + u8 sfp_csr; /* 0x14 - SFP+ control and status register */ + u8 misc_csr; /* 0x15 - Misc control and status register */ + u8 boot_or; /* 0x16 - Boot config override register */ + u8 boot_cfg1; /* 0x17 - Boot configuration register 1 */ + u8 boot_cfg2; /* 0x18 - Boot configuration register 2 */ +} cpld_data_t; + +u8 cpld_read(unsigned int reg); +void cpld_write(unsigned int reg, u8 value); + +#define CPLD_READ(reg) cpld_read(offsetof(struct cpld_data, reg)) +#define CPLD_WRITE(reg, value) \ + cpld_write(offsetof(struct cpld_data, reg), value) + +/* CPLD on IFC */ +#define CPLD_LBMAP_MASK 0x3F +#define CPLD_BANK_SEL_MASK 0x07 +#define CPLD_BANK_OVERRIDE 0x40 +#define CPLD_LBMAP_ALTBANK 0x43 /* BANK OR | BANK 4 */ +#define CPLD_LBMAP_DFLTBANK 0x47 /* BANK OR | BANK 0 */ +#define CPLD_LBMAP_RESET 0xFF +#define CPLD_LBMAP_SHIFT 0x03 +#define CPLD_BOOT_SEL 0x80 diff --git a/board/freescale/t208xrdb/ddr.c b/board/freescale/t208xrdb/ddr.c new file mode 100644 index 0000000000..01e917398f --- /dev/null +++ b/board/freescale/t208xrdb/ddr.c @@ -0,0 +1,112 @@ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * Version 2 or later as published by the Free Software Foundation. + */ + +#include +#include +#include +#include +#include +#include +#include +#include "ddr.h" + +DECLARE_GLOBAL_DATA_PTR; + +void fsl_ddr_board_options(memctl_options_t *popts, + dimm_params_t *pdimm, + unsigned int ctrl_num) +{ + const struct board_specific_parameters *pbsp, *pbsp_highest = NULL; + ulong ddr_freq; + + if (ctrl_num > 1) { + printf("Not supported controller number %d\n", ctrl_num); + return; + } + if (!pdimm->n_ranks) + return; + + pbsp = udimms[0]; + + /* Get clk_adjust, wrlvl_start, wrlvl_ctl, according to the board ddr + * freqency and n_banks specified in board_specific_parameters table. + */ + ddr_freq = get_ddr_freq(0) / 1000000; + while (pbsp->datarate_mhz_high) { + if (pbsp->n_ranks == pdimm->n_ranks && + (pdimm->rank_density >> 30) >= pbsp->rank_gb) { + if (ddr_freq <= pbsp->datarate_mhz_high) { + popts->clk_adjust = pbsp->clk_adjust; + popts->wrlvl_start = pbsp->wrlvl_start; + popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; + popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; + goto found; + } + pbsp_highest = pbsp; + } + pbsp++; + } + + if (pbsp_highest) { + printf("Error: board specific timing not found"); + printf("for data rate %lu MT/s\n", ddr_freq); + printf("Trying to use the highest speed (%u) parameters\n", + pbsp_highest->datarate_mhz_high); + popts->clk_adjust = pbsp_highest->clk_adjust; + popts->wrlvl_start = pbsp_highest->wrlvl_start; + popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; + popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; + } else { + panic("DIMM is not supported by this board"); + } +found: + debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n" + "\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, " + "wrlvl_ctrl_3 0x%x\n", + pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb, + pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2, + pbsp->wrlvl_ctl_3); + + /* + * Factors to consider for half-strength driver enable: + * - number of DIMMs installed + */ + popts->half_strength_driver_enable = 0; + /* + * Write leveling override + */ + popts->wrlvl_override = 1; + popts->wrlvl_sample = 0xf; + + /* + * Rtt and Rtt_WR override + */ + popts->rtt_override = 0; + + /* Enable ZQ calibration */ + popts->zq_en = 1; + + /* DHC_EN =1, ODT = 75 Ohm */ + popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm); + popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm); +} + +phys_size_t initdram(int board_type) +{ + phys_size_t dram_size; + + puts("Initializing....using SPD\n"); + + dram_size = fsl_ddr_sdram(); + + dram_size = setup_ddr_tlbs(dram_size / 0x100000); + dram_size *= 0x100000; + + puts(" DDR: "); + return dram_size; +} diff --git a/board/freescale/t208xrdb/ddr.h b/board/freescale/t208xrdb/ddr.h new file mode 100644 index 0000000000..b6d406219e --- /dev/null +++ b/board/freescale/t208xrdb/ddr.h @@ -0,0 +1,47 @@ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __DDR_H__ +#define __DDR_H__ +struct board_specific_parameters { + u32 n_ranks; + u32 datarate_mhz_high; + u32 rank_gb; + u32 clk_adjust; + u32 wrlvl_start; + u32 wrlvl_ctl_2; + u32 wrlvl_ctl_3; +}; + +/* + * These tables contain all valid speeds we want to override with board + * specific parameters. datarate_mhz_high values need to be in ascending order + * for each n_ranks group. + */ + +static const struct board_specific_parameters udimm0[] = { + /* + * memory controller 0 + * num| hi| rank| clk| wrlvl | wrlvl | wrlvl | + * ranks| mhz| GB |adjst| start | ctl2 | ctl3 | + */ + {2, 1200, 2, 5, 7, 0x0808090a, 0x0b0c0c0a}, + {2, 1500, 2, 5, 6, 0x07070809, 0x0a0b0b09}, + {2, 1600, 2, 5, 8, 0x0808070b, 0x0c0d0e0a}, + {2, 1700, 2, 4, 7, 0x080a0a0c, 0x0c0d0e0a}, + {2, 1900, 2, 5, 9, 0x0a0b0c0e, 0x0f10120c}, + {1, 1200, 2, 5, 7, 0x0808090a, 0x0b0c0c0a}, + {1, 1500, 2, 5, 6, 0x07070809, 0x0a0b0b09}, + {1, 1600, 2, 5, 8, 0x0808070b, 0x0c0d0e0a}, + {1, 1700, 2, 4, 7, 0x080a0a0c, 0x0c0d0e0a}, + {1, 1900, 2, 5, 9, 0x0a0b0c0e, 0x0f10120c}, + {} +}; + +static const struct board_specific_parameters *udimms[] = { + udimm0, +}; +#endif diff --git a/board/freescale/t208xrdb/eth_t208xrdb.c b/board/freescale/t208xrdb/eth_t208xrdb.c new file mode 100644 index 0000000000..cbbc625831 --- /dev/null +++ b/board/freescale/t208xrdb/eth_t208xrdb.c @@ -0,0 +1,106 @@ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * + * Shengzhou Liu + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +int board_eth_init(bd_t *bis) +{ +#if defined(CONFIG_FMAN_ENET) + int i, interface; + struct memac_mdio_info dtsec_mdio_info; + struct memac_mdio_info tgec_mdio_info; + struct mii_dev *dev; + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + u32 srds_s1; + + srds_s1 = in_be32(&gur->rcwsr[4]) & + FSL_CORENET2_RCWSR4_SRDS1_PRTCL; + srds_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT; + + dtsec_mdio_info.regs = + (struct memac_mdio_controller *)CONFIG_SYS_FM1_DTSEC_MDIO_ADDR; + + dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME; + + /* Register the 1G MDIO bus */ + fm_memac_mdio_init(bis, &dtsec_mdio_info); + + tgec_mdio_info.regs = + (struct memac_mdio_controller *)CONFIG_SYS_FM1_TGEC_MDIO_ADDR; + tgec_mdio_info.name = DEFAULT_FM_TGEC_MDIO_NAME; + + /* Register the 10G MDIO bus */ + fm_memac_mdio_init(bis, &tgec_mdio_info); + + /* Set the two on-board RGMII PHY address */ + fm_info_set_phy_address(FM1_DTSEC3, RGMII_PHY1_ADDR); + fm_info_set_phy_address(FM1_DTSEC4, RGMII_PHY2_ADDR); + + switch (srds_s1) { + case 0x66: + case 0x6b: + fm_info_set_phy_address(FM1_10GEC1, CORTINA_PHY_ADDR1); + fm_info_set_phy_address(FM1_10GEC2, CORTINA_PHY_ADDR2); + fm_info_set_phy_address(FM1_10GEC3, FM1_10GEC3_PHY_ADDR); + fm_info_set_phy_address(FM1_10GEC4, FM1_10GEC4_PHY_ADDR); + break; + default: + printf("SerDes1 protocol 0x%x is not supported on T208xRDB\n", + srds_s1); + break; + } + + for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) { + interface = fm_info_get_enet_if(i); + switch (interface) { + case PHY_INTERFACE_MODE_RGMII: + dev = miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME); + fm_info_set_mdio(i, dev); + break; + default: + break; + } + } + + for (i = FM1_10GEC1; i < FM1_10GEC1 + CONFIG_SYS_NUM_FM1_10GEC; i++) { + switch (fm_info_get_enet_if(i)) { + case PHY_INTERFACE_MODE_XGMII: + dev = miiphy_get_dev_by_name(DEFAULT_FM_TGEC_MDIO_NAME); + fm_info_set_mdio(i, dev); + break; + default: + break; + } + } + + cpu_eth_init(bis); +#endif /* CONFIG_FMAN_ENET */ + + return pci_eth_init(bis); +} + +void fdt_fixup_board_enet(void *fdt) +{ + return; +} diff --git a/board/freescale/t208xrdb/law.c b/board/freescale/t208xrdb/law.c new file mode 100644 index 0000000000..eb82431e22 --- /dev/null +++ b/board/freescale/t208xrdb/law.c @@ -0,0 +1,34 @@ +/* + * Copyright 2008-2014 Freescale Semiconductor, Inc. + * + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include +#include + +struct law_entry law_table[] = { + SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_IFC), +#ifdef CONFIG_SYS_BMAN_MEM_PHYS + SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_BMAN), +#endif +#ifdef CONFIG_SYS_QMAN_MEM_PHYS + SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_QMAN), +#endif +#ifdef CONFIG_SYS_CPLD_BASE_PHYS + SET_LAW(CONFIG_SYS_CPLD_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_IFC), +#endif +#ifdef CONFIG_SYS_DCSRBAR_PHYS + /* Limit DCSR to 32M to access NPC Trace Buffer */ + SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_DCSR), +#endif +#ifdef CONFIG_SYS_NAND_BASE_PHYS + SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_IFC), +#endif +}; + +int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/freescale/t208xrdb/pci.c b/board/freescale/t208xrdb/pci.c new file mode 100644 index 0000000000..ba7041af95 --- /dev/null +++ b/board/freescale/t208xrdb/pci.c @@ -0,0 +1,23 @@ +/* + * Copyright 2007-2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include +#include +#include +#include +#include +#include + +void pci_init_board(void) +{ + fsl_pcie_init_board(0); +} + +void pci_of_setup(void *blob, bd_t *bd) +{ + FT_FSL_PCI_SETUP; +} diff --git a/board/freescale/t208xrdb/t2080_pbi.cfg b/board/freescale/t208xrdb/t2080_pbi.cfg new file mode 100644 index 0000000000..e200d926fb --- /dev/null +++ b/board/freescale/t208xrdb/t2080_pbi.cfg @@ -0,0 +1,41 @@ +# +# Copyright 2013 Freescale Semiconductor, Inc. +# +# SPDX-License-Identifier: GPL-2.0+ +# +# Refer doc/README.pblimage for more details about how-to configure +# and create PBL boot image +# + +#PBI commands +#Initialize CPC1 +09010000 00200400 +09138000 00000000 +091380c0 00000100 +#512KB SRAM +09010100 00000000 +09010104 fff80009 +09010f00 08000000 +#enable CPC1 +09010000 80000000 +#Configure LAW for CPC1 +09000d00 00000000 +09000d04 fff80000 +09000d08 81000012 +#Initialize eSPI controller, default configuration is slow for eSPI to +#load data, this configuration comes from u-boot eSPI driver. +09110000 80000403 +09110020 2d170008 +09110024 00100008 +09110028 00100008 +0911002c 00100008 +#Errata for slowing down the MDC clock to make it <= 2.5 MHZ +094fc030 00008148 +094fd030 00008148 +#Configure alternate space +09000010 00000000 +09000014 ff000000 +09000018 81000000 +#Flush PBL data +09138000 00000000 +091380c0 00000000 diff --git a/board/freescale/t208xrdb/t2080_rcw.cfg b/board/freescale/t208xrdb/t2080_rcw.cfg new file mode 100644 index 0000000000..cd62cc8641 --- /dev/null +++ b/board/freescale/t208xrdb/t2080_rcw.cfg @@ -0,0 +1,8 @@ +#PBL preamble and RCW header for T2080RDB +aa55aa55 010e0100 +#SerDes Protocol: 0x66_0x16 +#Core/DDR: 1533Mhz/1600MT/s +120c0017 15000000 00000000 00000000 +66160002 00008400 ec104000 c1000000 +00000000 00000000 00000000 000307fc +00000000 00000000 00000000 00000004 diff --git a/board/freescale/t208xrdb/t208xrdb.c b/board/freescale/t208xrdb/t208xrdb.c new file mode 100644 index 0000000000..f3fec2aa6e --- /dev/null +++ b/board/freescale/t208xrdb/t208xrdb.c @@ -0,0 +1,124 @@ +/* + * Copyright 2009-2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include "t208xrdb.h" +#include "cpld.h" + +DECLARE_GLOBAL_DATA_PTR; + +int checkboard(void) +{ + struct cpu_type *cpu = gd->arch.cpu; + static const char *freq[3] = {"100.00MHZ", "125.00MHz", "156.25MHZ"}; + + printf("Board: %sRDB, ", cpu->name); + printf("Board rev: 0x%02x CPLD ver: 0x%02x, boot from ", + CPLD_READ(hw_ver), CPLD_READ(sw_ver)); + +#ifdef CONFIG_SDCARD + puts("SD/MMC\n"); +#elif CONFIG_SPIFLASH + puts("SPI\n"); +#else + u8 reg; + + reg = CPLD_READ(flash_csr); + + if (reg & CPLD_BOOT_SEL) { + puts("NAND\n"); + } else { + reg = ((reg & CPLD_LBMAP_MASK) >> CPLD_LBMAP_SHIFT); + printf("NOR vBank%d\n", ~reg & 0x7); + } +#endif + + puts("SERDES Reference Clocks:\n"); + printf("SD1_CLK1=%s, SD1_CLK2=%s\n", freq[2], freq[0]); + printf("SD2_CLK1=%s, SD2_CLK2=%s\n", freq[0], freq[0]); + + return 0; +} + +int board_early_init_r(void) +{ + const unsigned int flashbase = CONFIG_SYS_FLASH_BASE; + const u8 flash_esel = find_tlb_idx((void *)flashbase, 1); + /* + * Remap Boot flash + PROMJET region to caching-inhibited + * so that flash can be erased properly. + */ + + /* Flush d-cache and invalidate i-cache of any FLASH data */ + flush_dcache(); + invalidate_icache(); + + /* invalidate existing TLB entry for flash + promjet */ + disable_tlb(flash_esel); + + set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, flash_esel, BOOKE_PAGESZ_256M, 1); + + set_liodns(); +#ifdef CONFIG_SYS_DPAA_QBMAN + setup_portals(); +#endif + + return 0; +} + +unsigned long get_board_sys_clk(void) +{ + return CONFIG_SYS_CLK_FREQ; +} + +unsigned long get_board_ddr_clk(void) +{ + return CONFIG_DDR_CLK_FREQ; +} + +int misc_init_r(void) +{ + return 0; +} + +void ft_board_setup(void *blob, bd_t *bd) +{ + phys_addr_t base; + phys_size_t size; + + ft_cpu_setup(blob, bd); + + base = getenv_bootm_low(); + size = getenv_bootm_size(); + + fdt_fixup_memory(blob, (u64)base, (u64)size); + +#ifdef CONFIG_PCI + pci_of_setup(blob, bd); +#endif + + fdt_fixup_liodn(blob); + fdt_fixup_dr_usb(blob, bd); + +#ifdef CONFIG_SYS_DPAA_FMAN + fdt_fixup_fman_ethernet(blob); + fdt_fixup_board_enet(blob); +#endif +} diff --git a/board/freescale/t208xrdb/t208xrdb.h b/board/freescale/t208xrdb/t208xrdb.h new file mode 100644 index 0000000000..13380d02a3 --- /dev/null +++ b/board/freescale/t208xrdb/t208xrdb.h @@ -0,0 +1,13 @@ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CORENET_DS_H__ +#define __CORENET_DS_H__ + +void fdt_fixup_board_enet(void *blob); +void pci_of_setup(void *blob, bd_t *bd); + +#endif diff --git a/board/freescale/t208xrdb/tlb.c b/board/freescale/t208xrdb/tlb.c new file mode 100644 index 0000000000..085d9f5c6a --- /dev/null +++ b/board/freescale/t208xrdb/tlb.c @@ -0,0 +1,151 @@ +/* + * Copyright 2008-2014 Freescale Semiconductor, Inc. + * + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include + +struct fsl_e_tlb_entry tlb_table[] = { + /* TLB 0 - for temp stack in cache */ + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, + CONFIG_SYS_INIT_RAM_ADDR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + + /* TLB 1 */ + /* *I*** - Covers boot page */ +#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L3_ADDR) + /* + * *I*G - L3SRAM. When L3 is used as 1M SRAM, the address of the + * SRAM is at 0xfff00000, it covered the 0xfffff000. + */ + SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_1M, 1), +#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) + /* + * SRIO_PCIE_BOOT-SLAVE. When slave boot, the address of the + * space is at 0xfff00000, it covered the 0xfffff000. + */ + SET_TLB_ENTRY(1, CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR, + CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_W|MAS2_G, + 0, 0, BOOKE_PAGESZ_1M, 1), +#else + SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_4K, 1), +#endif + + /* *I*G* - CCSRBAR */ + SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 1, BOOKE_PAGESZ_16M, 1), + + /* *I*G* - Flash, localbus */ + /* This will be changed to *I*G* after relocation to RAM. */ + SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS, + MAS3_SX|MAS3_SR, MAS2_W|MAS2_G, + 0, 2, BOOKE_PAGESZ_256M, 1), + + /* *I*G* - PCIe 1, 0x80000000 */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 3, BOOKE_PAGESZ_512M, 1), + + /* *I*G* - PCIe 2, 0xa0000000 */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE2_MEM_VIRT, CONFIG_SYS_PCIE2_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 4, BOOKE_PAGESZ_256M, 1), + + /* *I*G* - PCIe 3, 0xb0000000 */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT, CONFIG_SYS_PCIE3_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 5, BOOKE_PAGESZ_256M, 1), + + + /* *I*G* - PCIe 4, 0xc0000000 */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE4_MEM_VIRT, CONFIG_SYS_PCIE4_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 6, BOOKE_PAGESZ_256M, 1), + + /* *I*G* - PCI I/O */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 7, BOOKE_PAGESZ_256K, 1), + + /* Bman/Qman */ +#ifdef CONFIG_SYS_BMAN_MEM_PHYS + SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 9, BOOKE_PAGESZ_16M, 1), + SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x01000000, + CONFIG_SYS_BMAN_MEM_PHYS + 0x01000000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 10, BOOKE_PAGESZ_16M, 1), +#endif +#ifdef CONFIG_SYS_QMAN_MEM_PHYS + SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 11, BOOKE_PAGESZ_16M, 1), + SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x01000000, + CONFIG_SYS_QMAN_MEM_PHYS + 0x01000000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 12, BOOKE_PAGESZ_16M, 1), +#endif +#ifdef CONFIG_SYS_DCSRBAR_PHYS + SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 13, BOOKE_PAGESZ_32M, 1), +#endif +#ifdef CONFIG_SYS_NAND_BASE + /* + * *I*G - NAND + * entry 14 and 15 has been used hard coded, they will be disabled + * in cpu_init_f, so we use entry 16 for nand. + */ + SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 16, BOOKE_PAGESZ_64K, 1), +#endif +#ifdef CONFIG_SYS_CPLD_BASE + SET_TLB_ENTRY(1, CONFIG_SYS_CPLD_BASE, CONFIG_SYS_CPLD_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 17, BOOKE_PAGESZ_4K, 1), +#endif +#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE + /* + * SRIO_PCIE_BOOT-SLAVE. 1M space from 0xffe00000 for + * fetching ucode and ENV from master + */ + SET_TLB_ENTRY(1, CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR, + CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_G, + 0, 18, BOOKE_PAGESZ_1M, 1), +#endif +#if defined(CONFIG_SYS_RAMBOOT) + SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 19, BOOKE_PAGESZ_2G, 1) +#endif + +}; + +int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/boards.cfg b/boards.cfg index 14cd15165c..1d3aab1d17 100644 --- a/boards.cfg +++ b/boards.cfg @@ -983,6 +983,11 @@ Active powerpc mpc85xx - freescale t208xqds Active powerpc mpc85xx - freescale t208xqds T2081QDS_SPIFLASH T208xQDS:PPC_T2081,RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF40000 Active powerpc mpc85xx - freescale t208xqds T2081QDS_NAND T208xQDS:PPC_T2081,RAMBOOT_PBL,NAND,SYS_TEXT_BASE=0xFFF40000 Active powerpc mpc85xx - freescale t208xqds T2081QDS_SRIO_PCIE_BOOT T208xQDS:PPC_T2081,SRIO_PCIE_BOOT_SLAVE,SYS_TEXT_BASE=0xFFF40000 +Active powerpc mpc85xx - freescale t208xrdb T2080RDB T208xRDB:PPC_T2080 +Active powerpc mpc85xx - freescale t208xrdb T2080RDB_SDCARD T208xRDB:PPC_T2080,RAMBOOT_PBL,SDCARD,SYS_TEXT_BASE=0xFFF40000 +Active powerpc mpc85xx - freescale t208xrdb T2080RDB_SPIFLASH T208xRDB:PPC_T2080,RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF40000 +Active powerpc mpc85xx - freescale t208xrdb T2080RDB_NAND T208xRDB:PPC_T2080,RAMBOOT_PBL,NAND,SYS_TEXT_BASE=0xFFF40000 +Active powerpc mpc85xx - freescale t208xrdb T2080RDB_SRIO_PCIE_BOOT T208xRDB:PPC_T2080,SRIO_PCIE_BOOT_SLAVE,SYS_TEXT_BASE=0xFFF40000 Active powerpc mpc85xx - freescale t4qds T4160QDS T4240QDS:PPC_T4160 - Active powerpc mpc85xx - freescale t4qds T4160QDS_SDCARD T4240QDS:PPC_T4160,RAMBOOT_PBL,SDCARD,SYS_TEXT_BASE=0xFFF40000 - Active powerpc mpc85xx - freescale t4qds T4160QDS_SPIFLASH T4240QDS:PPC_T4160,RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF40000 - diff --git a/include/configs/T208xRDB.h b/include/configs/T208xRDB.h new file mode 100644 index 0000000000..979843bf4b --- /dev/null +++ b/include/configs/T208xRDB.h @@ -0,0 +1,779 @@ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/* + * T2080 RDB/PCIe board configuration file + */ + +#ifndef __T2080RDB_H +#define __T2080RDB_H + +#define CONFIG_T2080RDB +#define CONFIG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */ +#define CONFIG_MMC +#define CONFIG_SPI_FLASH +#define CONFIG_USB_EHCI +#define CONFIG_FSL_SATA_V2 + +/* High Level Configuration Options */ +#define CONFIG_PHYS_64BIT +#define CONFIG_BOOKE +#define CONFIG_E500 /* BOOKE e500 family */ +#define CONFIG_E500MC /* BOOKE e500mc family */ +#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ +#define CONFIG_MP /* support multiple processors */ +#define CONFIG_ENABLE_36BIT_PHYS + +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_ADDR_MAP 1 +#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ +#endif + +#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ +#define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS +#define CONFIG_FSL_IFC /* Enable IFC Support */ +#define CONFIG_FSL_LAW /* Use common FSL init code */ +#define CONFIG_ENV_OVERWRITE + +#ifdef CONFIG_RAMBOOT_PBL +#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE +#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc +#define CONFIG_SYS_FSL_PBL_PBI $(SRCTREE)/board/freescale/t208xrdb/t2080_pbi.cfg +#define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/freescale/t208xrdb/t2080_rcw.cfg +#endif + +#define CONFIG_SRIO_PCIE_BOOT_MASTER +#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE +/* Set 1M boot space */ +#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000) +#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \ + (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR) +#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc +#define CONFIG_SYS_NO_FLASH +#endif + +#ifndef CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_TEXT_BASE 0xeff40000 +#endif + +#ifndef CONFIG_RESET_VECTOR_ADDRESS +#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc +#endif + +/* + * These can be toggled for performance analysis, otherwise use default. + */ +#define CONFIG_SYS_CACHE_STASHING +#define CONFIG_BTB /* toggle branch predition */ +#define CONFIG_DDR_ECC +#ifdef CONFIG_DDR_ECC +#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER +#define CONFIG_MEM_INIT_VALUE 0xdeadbeef +#endif + +#ifdef CONFIG_SYS_NO_FLASH +#if !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) && !defined(CONFIG_RAMBOOT_PBL) +#define CONFIG_ENV_IS_NOWHERE +#endif +#else +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE +#endif + +#if defined(CONFIG_SPIFLASH) +#define CONFIG_SYS_EXTRA_ENV_RELOC +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_SPI_BUS 0 +#define CONFIG_ENV_SPI_CS 0 +#define CONFIG_ENV_SPI_MAX_HZ 10000000 +#define CONFIG_ENV_SPI_MODE 0 +#define CONFIG_ENV_SIZE 0x2000 /* 8KB */ +#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ +#define CONFIG_ENV_SECT_SIZE 0x10000 +#elif defined(CONFIG_SDCARD) +#define CONFIG_SYS_EXTRA_ENV_RELOC +#define CONFIG_ENV_IS_IN_MMC +#define CONFIG_SYS_MMC_ENV_DEV 0 +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_OFFSET (512 * 1658) +#elif defined(CONFIG_NAND) +#define CONFIG_SYS_EXTRA_ENV_RELOC +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE +#define CONFIG_ENV_OFFSET (2 * CONFIG_SYS_NAND_BLOCK_SIZE) +#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) +#define CONFIG_ENV_IS_IN_REMOTE +#define CONFIG_ENV_ADDR 0xffe20000 +#define CONFIG_ENV_SIZE 0x2000 +#elif defined(CONFIG_ENV_IS_NOWHERE) +#define CONFIG_ENV_SIZE 0x2000 +#else +#define CONFIG_ENV_IS_IN_FLASH +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ +#endif + +#ifndef __ASSEMBLY__ +unsigned long get_board_sys_clk(void); +unsigned long get_board_ddr_clk(void); +#endif + +#define CONFIG_SYS_CLK_FREQ 66660000 +#define CONFIG_DDR_CLK_FREQ 133330000 + +/* + * Config the L3 Cache as L3 SRAM + */ +#define CONFIG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE + +#define CONFIG_SYS_DCSRBAR 0xf0000000 +#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull + +/* EEPROM */ +#define CONFIG_ID_EEPROM +#define CONFIG_SYS_I2C_EEPROM_NXID +#define CONFIG_SYS_EEPROM_BUS_NUM 0 +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 + +/* + * DDR Setup + */ +#define CONFIG_VERY_BIG_RAM +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 +#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR) +#define CONFIG_DDR_SPD +#define CONFIG_SYS_FSL_DDR3 +#undef CONFIG_FSL_DDR_INTERACTIVE +#define CONFIG_SYS_SPD_BUS_NUM 0 +#define CONFIG_SYS_SDRAM_SIZE 2048 /* for fixed parameter use */ +#define SPD_EEPROM_ADDRESS1 0x51 +#define SPD_EEPROM_ADDRESS2 0x52 +#define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 +#define CTRL_INTLV_PREFERED cacheline + +/* + * IFC Definitions + */ +#define CONFIG_SYS_FLASH_BASE 0xe8000000 +#define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE) +#define CONFIG_SYS_NOR0_CSPR_EXT (0xf) +#define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ + CSPR_PORT_SIZE_16 | \ + CSPR_MSEL_NOR | \ + CSPR_V) +#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024) + +/* NOR Flash Timing Params */ +#define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80 + +#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ + FTIM0_NOR_TEADC(0x5) | \ + FTIM0_NOR_TEAHC(0x5)) +#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ + FTIM1_NOR_TRAD_NOR(0x1A) |\ + FTIM1_NOR_TSEQRAD_NOR(0x13)) +#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ + FTIM2_NOR_TCH(0x4) | \ + FTIM2_NOR_TWPH(0x0E) | \ + FTIM2_NOR_TWP(0x1c)) +#define CONFIG_SYS_NOR_FTIM3 0x0 + +#define CONFIG_SYS_FLASH_QUIET_TEST +#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ + +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ +#define CONFIG_SYS_FLASH_EMPTY_INFO +#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS } + +/* CPLD on IFC */ +#define CONFIG_SYS_CPLD_BASE 0xffdf0000 +#define CONFIG_SYS_CPLD_BASE_PHYS (0xf00000000ull | CONFIG_SYS_CPLD_BASE) +#define CONFIG_SYS_CSPR2_EXT (0xf) +#define CONFIG_SYS_CSPR2 (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE) \ + | CSPR_PORT_SIZE_8 \ + | CSPR_MSEL_GPCM \ + | CSPR_V) +#define CONFIG_SYS_AMASK2 IFC_AMASK(64*1024) +#define CONFIG_SYS_CSOR2 0x0 + +/* CPLD Timing parameters for IFC CS2 */ +#define CONFIG_SYS_CS2_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ + FTIM0_GPCM_TEADC(0x0e) | \ + FTIM0_GPCM_TEAHC(0x0e)) +#define CONFIG_SYS_CS2_FTIM1 (FTIM1_GPCM_TACO(0x0e) | \ + FTIM1_GPCM_TRAD(0x1f)) +#define CONFIG_SYS_CS2_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \ + FTIM2_GPCM_TCH(0x0) | \ + FTIM2_GPCM_TWP(0x1f)) +#define CONFIG_SYS_CS2_FTIM3 0x0 + +/* NAND Flash on IFC */ +#define CONFIG_NAND_FSL_IFC +#define CONFIG_SYS_NAND_BASE 0xff800000 +#define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE) + +#define CONFIG_SYS_NAND_CSPR_EXT (0xf) +#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ + | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ + | CSPR_MSEL_NAND /* MSEL = NAND */ \ + | CSPR_V) +#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024) + +#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ + | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ + | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ + | CSOR_NAND_RAL_3 /* RAL = 2Byes */ \ + | CSOR_NAND_PGS_2K /* Page Size = 2K */\ + | CSOR_NAND_SPRZ_64 /* Spare size = 64 */\ + | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/ + +#define CONFIG_SYS_NAND_ONFI_DETECTION + +/* ONFI NAND Flash mode0 Timing Params */ +#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \ + FTIM0_NAND_TWP(0x18) | \ + FTIM0_NAND_TWCHT(0x07) | \ + FTIM0_NAND_TWH(0x0a)) +#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \ + FTIM1_NAND_TWBE(0x39) | \ + FTIM1_NAND_TRR(0x0e) | \ + FTIM1_NAND_TRP(0x18)) +#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \ + FTIM2_NAND_TREH(0x0a) | \ + FTIM2_NAND_TWHRE(0x1e)) +#define CONFIG_SYS_NAND_FTIM3 0x0 + +#define CONFIG_SYS_NAND_DDR_LAW 11 +#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_MTD_NAND_VERIFY_WRITE +#define CONFIG_CMD_NAND +#define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024) + +#if defined(CONFIG_NAND) +#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT +#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR +#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK +#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR +#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 +#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 +#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 +#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 +#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT +#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR0_CSPR +#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK +#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR +#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 +#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 +#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 +#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 +#else +#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT +#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR +#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK +#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR +#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 +#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 +#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 +#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 +#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NAND_CSPR_EXT +#define CONFIG_SYS_CSPR1 CONFIG_SYS_NAND_CSPR +#define CONFIG_SYS_AMASK1 CONFIG_SYS_NAND_AMASK +#define CONFIG_SYS_CSOR1 CONFIG_SYS_NAND_CSOR +#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NAND_FTIM0 +#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NAND_FTIM1 +#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NAND_FTIM2 +#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3 +#endif + +#if defined(CONFIG_RAMBOOT_PBL) +#define CONFIG_SYS_RAMBOOT +#endif + +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE +#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ +#define CONFIG_MISC_INIT_R +#define CONFIG_HWCONFIG + +/* define to use L1 as initial stack */ +#define CONFIG_L1_INIT_RAM +#define CONFIG_SYS_INIT_RAM_LOCK +#define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */ +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe0ec000 +/* The assembler doesn't like typecast */ +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ + ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ + CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) +#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ + GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET +#define CONFIG_SYS_MONITOR_LEN (512 * 1024) +#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) + +/* + * Serial Port + */ +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) +#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) +#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) + +/* Use the HUSH parser */ +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " + +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT +#define CONFIG_OF_BOARD_SETUP +#define CONFIG_OF_STDOUT_VIA_ALIAS + +/* new uImage format support */ +#define CONFIG_FIT +#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ + +/* + * I2C + */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C3_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C4_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100 +#define CONFIG_SYS_FSL_I2C3_OFFSET 0x119000 +#define CONFIG_SYS_FSL_I2C4_OFFSET 0x119100 +#define CONFIG_SYS_FSL_I2C_SPEED 100000 +#define CONFIG_SYS_FSL_I2C2_SPEED 100000 +#define CONFIG_SYS_FSL_I2C3_SPEED 100000 +#define CONFIG_SYS_FSL_I2C4_SPEED 100000 +#define I2C_MUX_PCA_ADDR_PRI 0x77 /* I2C bus multiplexer,primary */ +#define I2C_MUX_PCA_ADDR_SEC1 0x75 /* I2C bus multiplexer,secondary 1 */ +#define I2C_MUX_PCA_ADDR_SEC2 0x76 /* I2C bus multiplexer,secondary 2 */ +#define I2C_MUX_CH_DEFAULT 0x8 + + +/* + * RapidIO + */ +#define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000 +#define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull +#define CONFIG_SYS_SRIO1_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000 +#define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull +#define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */ +/* + * for slave u-boot IMAGE instored in master memory space, + * PHYS must be aligned based on the SIZE + */ +#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef080000ull +#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff80000ull +#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x80000 /* 512K */ +#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff80000ull +/* + * for slave UCODE and ENV instored in master memory space, + * PHYS must be aligned based on the SIZE + */ +#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef040000ull +#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull +#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */ + +/* slave core release by master*/ +#define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4 +#define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */ + +/* + * SRIO_PCIE_BOOT - SLAVE + */ +#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE +#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000 +#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \ + (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR) +#endif + +/* + * eSPI - Enhanced SPI + */ +#ifdef CONFIG_SPI_FLASH +#define CONFIG_FSL_ESPI +#define CONFIG_SPI_FLASH_STMICRO +#define CONFIG_SPI_FLASH_BAR +#define CONFIG_CMD_SF +#define CONFIG_SF_DEFAULT_SPEED 10000000 +#define CONFIG_SF_DEFAULT_MODE 0 +#endif + +/* + * General PCI + * Memory space is mapped 1-1, but I/O space must start from 0. + */ +#define CONFIG_PCI /* Enable PCI/PCIE */ +#define CONFIG_PCIE1 /* PCIE controler 1 */ +#define CONFIG_PCIE2 /* PCIE controler 2 */ +#define CONFIG_PCIE3 /* PCIE controler 3 */ +#define CONFIG_PCIE4 /* PCIE controler 4 */ +#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ +#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ +/* controller 1, direct to uli, tgtid 3, Base address 20000 */ +#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 +#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 +#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull +#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ + +/* controller 2, Slot 2, tgtid 2, Base address 201000 */ +#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 +#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull +#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000 +#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull +#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ + +/* controller 3, Slot 1, tgtid 1, Base address 202000 */ +#define CONFIG_SYS_PCIE3_MEM_VIRT 0xb0000000 +#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc30000000ull +#define CONFIG_SYS_PCIE3_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000 +#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull +#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ + +/* controller 4, Base address 203000 */ +#define CONFIG_SYS_PCIE4_MEM_VIRT 0xc0000000 +#define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE4_MEM_PHYS 0xc40000000ull +#define CONFIG_SYS_PCIE4_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCIE4_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull +#define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */ + +#ifdef CONFIG_PCI +#define CONFIG_PCI_INDIRECT_BRIDGE +#define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata LSZ ADD */ +#define CONFIG_NET_MULTI +#define CONFIG_E1000 +#define CONFIG_PCI_PNP /* do pci plug-and-play */ +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CONFIG_DOS_PARTITION +#endif + +/* Qman/Bman */ +#ifndef CONFIG_NOBQFMAN +#define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */ +#define CONFIG_SYS_BMAN_NUM_PORTALS 18 +#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 +#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull +#define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000 +#define CONFIG_SYS_QMAN_NUM_PORTALS 18 +#define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000 +#define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull +#define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000 + +#define CONFIG_SYS_DPAA_FMAN +#define CONFIG_SYS_DPAA_PME +#define CONFIG_SYS_PMAN +#define CONFIG_SYS_DPAA_DCE +#define CONFIG_SYS_DPAA_RMAN /* RMan */ +#define CONFIG_SYS_INTERLAKEN + +/* Default address of microcode for the Linux Fman driver */ +#if defined(CONFIG_SPIFLASH) +/* + * env is stored at 0x100000, sector size is 0x10000, ucode is stored after + * env, so we got 0x110000. + */ +#define CONFIG_SYS_QE_FW_IN_SPIFLASH +#define CONFIG_SYS_QE_FMAN_FW_ADDR 0x110000 +#define CONFIG_CORTINA_FW_ADDR 0x120000 + +#elif defined(CONFIG_SDCARD) +/* + * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is + * about 825KB (1650 blocks), Env is stored after the image, and the env size is + * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680. + */ +#define CONFIG_SYS_QE_FMAN_FW_IN_MMC +#define CONFIG_SYS_QE_FMAN_FW_ADDR (512 * 1680) +#define CONFIG_CORTINA_FW_ADDR (512 * 1808) + +#elif defined(CONFIG_NAND) +#define CONFIG_SYS_QE_FMAN_FW_IN_NAND +#define CONFIG_SYS_QE_FMAN_FW_ADDR (6 * CONFIG_SYS_NAND_BLOCK_SIZE) +#define CONFIG_CORTINA_FW_ADDR (7 * CONFIG_SYS_NAND_BLOCK_SIZE) +#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) +/* + * Slave has no ucode locally, it can fetch this from remote. When implementing + * in two corenet boards, slave's ucode could be stored in master's memory + * space, the address can be mapped from slave TLB->slave LAW-> + * slave SRIO or PCIE outbound window->master inbound window-> + * master LAW->the ucode address in master's memory space. + */ +#define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE +#define CONFIG_SYS_QE_FMAN_FW_ADDR 0xFFE00000 +#define CONFIG_CORTINA_FW_ADDR 0xFFE10000 +#else +#define CONFIG_SYS_QE_FMAN_FW_IN_NOR +#define CONFIG_SYS_QE_FMAN_FW_ADDR 0xEFF00000 +#define CONFIG_CORTINA_FW_ADDR 0xEFE00000 +#endif +#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 +#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) +#endif /* CONFIG_NOBQFMAN */ + +#ifdef CONFIG_SYS_DPAA_FMAN +#define CONFIG_FMAN_ENET +#define CONFIG_PHYLIB_10G +#define CONFIG_PHY_CORTINA +#define CONFIG_PHY_AQ1202 +#define CONFIG_PHY_REALTEK +#define CONFIG_CORTINA_FW_LENGTH 0x40000 +#define RGMII_PHY1_ADDR 0x01 /* RealTek RTL8211E */ +#define RGMII_PHY2_ADDR 0x02 +#define CORTINA_PHY_ADDR1 0x0c /* Cortina CS4315 */ +#define CORTINA_PHY_ADDR2 0x0d +#define FM1_10GEC3_PHY_ADDR 0x00 /* Aquantia AQ1202 10G Base-T */ +#define FM1_10GEC4_PHY_ADDR 0x01 +#endif + + +#ifdef CONFIG_FMAN_ENET +#define CONFIG_MII /* MII PHY management */ +#define CONFIG_ETHPRIME "FM1@DTSEC3" +#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ +#endif + +/* + * SATA + */ +#ifdef CONFIG_FSL_SATA_V2 +#define CONFIG_LIBATA +#define CONFIG_FSL_SATA +#define CONFIG_SYS_SATA_MAX_DEVICE 2 +#define CONFIG_SATA1 +#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR +#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA +#define CONFIG_SATA2 +#define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR +#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA +#define CONFIG_LBA48 +#define CONFIG_CMD_SATA +#define CONFIG_DOS_PARTITION +#define CONFIG_CMD_EXT2 +#endif + +/* + * USB + */ +#ifdef CONFIG_USB_EHCI +#define CONFIG_CMD_USB +#define CONFIG_USB_STORAGE +#define CONFIG_USB_EHCI_FSL +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET +#define CONFIG_CMD_EXT2 +#define CONFIG_HAS_FSL_DR_USB +#endif + +/* + * SDHC + */ +#ifdef CONFIG_MMC +#define CONFIG_CMD_MMC +#define CONFIG_FSL_ESDHC +#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR +#define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT +#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 +#define CONFIG_GENERIC_MMC +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT +#define CONFIG_DOS_PARTITION +#endif + +/* + * Environment + */ + +/* + * Command line configuration. + */ +#include + +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_ELF +#define CONFIG_CMD_MII +#define CONFIG_CMD_I2C +#define CONFIG_CMD_PING +#define CONFIG_CMD_ECHO +#define CONFIG_CMD_SETEXPR +#define CONFIG_CMD_REGINFO +#define CONFIG_CMD_BDI + +#ifdef CONFIG_PCI +#define CONFIG_CMD_PCI +#define CONFIG_CMD_NET +#endif + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ +#ifdef CONFIG_CMD_KGDB +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks*/ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 64 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/ +#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ + +#ifdef CONFIG_CMD_KGDB +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * Environment Configuration + */ +#define CONFIG_ROOTPATH "/opt/nfsroot" +#define CONFIG_BOOTFILE "uImage" +#define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server */ + +/* default location for tftp and bootm */ +#define CONFIG_LOADADDR 1000000 +#define CONFIG_BAUDRATE 115200 +#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ +#define __USB_PHY_TYPE utmi + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "hwconfig=fsl_ddr:" \ + "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) "," \ + "bank_intlv=auto;" \ + "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\ + "netdev=eth0\0" \ + "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ + "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ + "tftpflash=tftpboot $loadaddr $uboot && " \ + "protect off $ubootaddr +$filesize && " \ + "erase $ubootaddr +$filesize && " \ + "cp.b $loadaddr $ubootaddr $filesize && " \ + "protect on $ubootaddr +$filesize && " \ + "cmp.b $loadaddr $ubootaddr $filesize\0" \ + "consoledev=ttyS0\0" \ + "ramdiskaddr=2000000\0" \ + "ramdiskfile=t2080rdb/ramdisk.uboot\0" \ + "fdtaddr=c00000\0" \ + "fdtfile=t2080rdb/t2080rdb.dtb\0" \ + "bdev=sda3\0" \ + "c=ffe\0" + +/* + * For emulation this causes u-boot to jump to the start of the + * proof point app code automatically + */ +#define CONFIG_PROOF_POINTS \ + "setenv bootargs root=/dev/$bdev rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "cpu 1 release 0x29000000 - - -;" \ + "cpu 2 release 0x29000000 - - -;" \ + "cpu 3 release 0x29000000 - - -;" \ + "cpu 4 release 0x29000000 - - -;" \ + "cpu 5 release 0x29000000 - - -;" \ + "cpu 6 release 0x29000000 - - -;" \ + "cpu 7 release 0x29000000 - - -;" \ + "go 0x29000000" + +#define CONFIG_HVBOOT \ + "setenv bootargs config-addr=0x60000000; " \ + "bootm 0x01000000 - 0x00f00000" + +#define CONFIG_ALU \ + "setenv bootargs root=/dev/$bdev rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "cpu 1 release 0x01000000 - - -;" \ + "cpu 2 release 0x01000000 - - -;" \ + "cpu 3 release 0x01000000 - - -;" \ + "cpu 4 release 0x01000000 - - -;" \ + "cpu 5 release 0x01000000 - - -;" \ + "cpu 6 release 0x01000000 - - -;" \ + "cpu 7 release 0x01000000 - - -;" \ + "go 0x01000000" + +#define CONFIG_LINUX \ + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "setenv ramdiskaddr 0x02000000;" \ + "setenv fdtaddr 0x00c00000;" \ + "setenv loadaddr 0x1000000;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr" + +#define CONFIG_HDBOOT \ + "setenv bootargs root=/dev/$bdev rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + +#define CONFIG_NFSBOOTCOMMAND \ + "setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$serverip:$rootpath " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + +#define CONFIG_RAMBOOTCOMMAND \ + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $ramdiskaddr $ramdiskfile;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr" + +#define CONFIG_BOOTCOMMAND CONFIG_LINUX + +#ifdef CONFIG_SECURE_BOOT +#include +#undef CONFIG_CMD_USB +#endif + +#endif /* __T2080RDB_H */ -- 2.30.2