From 819e7946b0964725dab50c92797f49cf4053d955 Mon Sep 17 00:00:00 2001 From: Jeff Kletsky Date: Wed, 10 Apr 2019 08:34:28 -0700 Subject: [PATCH] ipq40xx: Add support for Linksys EA8300 (Dallas) The Linksys EA8300 is based on QCA4019 and QCA9888 and provides three, independent radios. NAND provides two, alternate kernel/firmware images with fail-over provided by the OEM U-Boot. Installation: "Factory" images may be installed directly through the OEM GUI. Hardware Highlights: * IPQ4019 at 717 MHz (4 CPUs) * 256 MB NAND (Winbond W29N02GV, 8-bit parallel) * 256 MB RAM * Three, fully-functional radios; `iw phy` reports (FCC/US, -CT): * 2.4 GHz radio at 30 dBm * 5 GHz radio on ch. 36-64 at 23 dBm * 5 GHz radio on ch. 100-144 at 23 dBm (DFS), 149-165 at 30 dBm #{ managed } <= 16, #{ AP, mesh point } <= 16, #{ IBSS } <= 1 * All two-stream, MCS 0-9 * 4x GigE LAN, 1x GigE Internet Ethernet jacks with port lights * USB3, single port on rear with LED * WPS and reset buttons * Four status lights on top * Serial pads internal (unpopulated) "Linksys Dallas WiFi AP router based on Qualcomm AP DK07.1-c1" Implementation Notes: The OEM flash layout is preserved at this time with 3 MB kernel and ~69 MB UBIFS for each firmware version. The sysdiag (1 MB) and syscfg (56 MB) partitions are untouched, available as read-only. Serial Connectivity: Serial connectivity is *not* required to flash. Serial may be accessed by opening the device and connecting a 3.3-V adapter using 115200, 8n1. U-Boot access is good, including the ability to load images over TFTP and either run or flash them. Looking at the top of the board, from the front of the unit, J3 can be found on the right edge of the board, near the rear | J3 | |-| | |O| | (3.3V seen, open-circuit) |O| | TXD |O| | RXD |O| | |O| | GND |-| | | Unimplemented: * serial1 "ttyQHS0" (serial0 works as console) * Bluetooth; Qualcomm CSR8811 (potentially conected to serial1) Other Notes: https://wikidevi.com/wiki/Linksys_EA8300 states FCC docs also cover the Linksys EA8250. According to the RF Test Report BT BR+EDR, "All models are identical except for the EA8300 supports 256QAM and the EA8250 disable 256QAM." Signed-off-by: Jeff Kletsky --- package/boot/uboot-envtools/files/ipq40xx | 3 + package/firmware/ipq-wifi/Makefile | 2 + .../ipq-wifi/board-linksys_ea8300.qca4019 | Bin 0 -> 97236 bytes .../ipq-wifi/board-linksys_ea8300.qca9888 | Bin 0 -> 48628 bytes .../ipq40xx/base-files/etc/board.d/02_network | 3 +- .../etc/hotplug.d/firmware/11-ath10k-caldata | 14 +- .../ipq40xx/base-files/etc/init.d/bootcount | 3 +- .../lib/preinit/05_set_iface_mac_ipq40xx.sh | 5 + .../preinit/06_set_preinit_iface_ipq40xx.sh | 1 + .../base-files/lib/upgrade/platform.sh | 13 +- .../boot/dts/qcom-ipq4019-linksys_ea8300.dts | 399 ++++++++++++++++++ .../boot/dts/qcom-ipq4019-linksys_ea8300.dts | 399 ++++++++++++++++++ target/linux/ipq40xx/image/Makefile | 15 + .../901-arm-boot-add-dts-files.patch | 3 +- .../901-arm-boot-add-dts-files.patch | 3 +- 15 files changed, 852 insertions(+), 11 deletions(-) create mode 100644 package/firmware/ipq-wifi/board-linksys_ea8300.qca4019 create mode 100644 package/firmware/ipq-wifi/board-linksys_ea8300.qca9888 create mode 100644 target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4019-linksys_ea8300.dts create mode 100644 target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-linksys_ea8300.dts diff --git a/package/boot/uboot-envtools/files/ipq40xx b/package/boot/uboot-envtools/files/ipq40xx index c16e60bac5..7bcad00b01 100644 --- a/package/boot/uboot-envtools/files/ipq40xx +++ b/package/boot/uboot-envtools/files/ipq40xx @@ -40,6 +40,9 @@ openmesh,a62) linksys,ea6350v3) ubootenv_add_uci_config "/dev/mtd7" "0x0" "0x20000" "0x20000" ;; +linksys,ea8300) + ubootenv_add_uci_config "/dev/mtd7" "0x0" "0x40000" "0x20000" + ;; zyxel,nbg6617) ubootenv_add_uci_config "/dev/mtd6" "0x0" "0x10000" "0x10000" ;; diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile index 5c4ebb23c4..922064b7f7 100644 --- a/package/firmware/ipq-wifi/Makefile +++ b/package/firmware/ipq-wifi/Makefile @@ -31,6 +31,7 @@ ALLWIFIBOARDS:= \ engenius_eap1300 \ engenius_ens620ext \ linksys_ea6350v3 \ + linksys_ea8300 \ qxwlan_e2600ac ALLWIFIPACKAGES:=$(foreach BOARD,$(ALLWIFIBOARDS),ipq-wifi-$(BOARD)) @@ -101,6 +102,7 @@ $(eval $(call generate-ipq-wifi-package,avm_fritzrepeater-3000,AVM FRITZ!Repeate $(eval $(call generate-ipq-wifi-package,engenius_eap1300,EnGenius EAP1300)) $(eval $(call generate-ipq-wifi-package,engenius_ens620ext,EnGenius ENS620EXT)) $(eval $(call generate-ipq-wifi-package,linksys_ea6350v3,Linksys EA6350v3)) +$(eval $(call generate-ipq-wifi-package,linksys_ea8300,Linksys EA8300)) $(eval $(call generate-ipq-wifi-package,qxwlan_e2600ac,Qxwlan E2600AC)) $(foreach PACKAGE,$(ALLWIFIPACKAGES),$(eval $(call BuildPackage,$(PACKAGE)))) diff --git a/package/firmware/ipq-wifi/board-linksys_ea8300.qca4019 b/package/firmware/ipq-wifi/board-linksys_ea8300.qca4019 new file mode 100644 index 0000000000000000000000000000000000000000..0a1f6ebd4785369593653491d70efc358c1238a9 GIT binary patch literal 97236 zcmeHQdvFs+o^C(Dgo9wova!LDg^(XIwrtDZM1a5#9M)hhup}`UIAWVeYz2d{G2oaz z%w9qq5RYJ%wJ`$2x_ElM4p1B<2D2pD&0Zzc{;^eebyu~!b$gesy6mxABv+fNyMybQ zQENuhv^*nANcQ|1X8Je3eoXh*J<`ndr_bMCQkq-(YDGbQWp3HZ($(dtv9S^1(3HpQ z5h})8U2Dst+WNYjy2ggwP4x{;xec2a<+De1J8GLZGl%B`fZ94jVU46Y!+aNoP!aqdj$DGoTzb>zy`@12_*&p-!s zrKq$#7R9^%krbwl#OCATz+22$f~~3U^Xd@y4?A_jEE=`&s8|yh7dL6rq!>X!=q}S! zi6If^6K+ZPShz{7#+_{j4(@|-ZZsVoV5W^Lcy{LAK=0wUE$b?mS?=BF?P_aW_v*5; zdslnkJ=EOr{beuSyN0cnhSkfy^DPda{?eFd^--@C$O z!#)cxaQM)kb+%;-*#e(sW}|x_^d7-y_};Sl_kM;8*x3RXaV7QZDlJ*Kx)W_p>sDLx zT?H~d+c(Nl8xEsn@l1vSo_L5KO$3z0dp5qj{fBG!%-@n(m0J0rt9k#@M$_wwWp}Uc z>{+k$@_qn|NX-x?= z;|nEdEkR&X+;e|3eTFI_ac0Ww7sv;`AZ9*e{RLbPz9C|E(b3US%swUte=SdTg}BQd zYx9#o`@t%+)?k>6|EKHc%$cj7qt{o(PVu@YAx(lfgb1u%yLyFQpN7xy*S|jg^OGmc z9gxMCK9}?T@1OtWOQDa+_``-xV#~3E?afe0KOl=R@45Y z1I)%ai}+y9H|1n!8H$Qrh8`zHjF0Vr*G{EXsYvd9*}TsjW0s+6uLW zj|x=_wF^xPZS34|;m_I38G6{$^rSHLa&Qq3li->q97@zZmy_Gm>S3mB(|dR-2)6Vw z2EkX0sOfd7jOlP9+>=5dq)Y)o2~eUS08@hkjE7s1D0v_N2Y>(|00;mAfB+z%U<78G zXR6ZF-!*?%wNm|(`6X4cdI||>b=`>z*FP5S-ESpi8NTOuj)b6{L%~A`U6+Z#*FHgJ z1)<9B$y%VFMQT2J4H21Q+feVg`2|8a-s|YQ`Gt2(-gIY>x8E6h9ryr)>}NC&N{|XA zd}-`Jr~qYPeoh)@0~s(CN{=@tKCUi6dVOlD-YcBMeqXO%zoE;3td=PB%?^Z4#;Kx8 ziV(`0qC!?=jjfriLeYuQQ#ar^KAv54jL2&i8WkJ_o(@gZL`QGND-d{fIXZUAk8wDU z1F8Ks4rB4z*5VJ>zMH?I#hDrDhH!4&${n{>$F0uUR=v7*L(S%T$MKWhXZrdt4-DPB zefQ^|{^|?)3Ha*cLZ%?(Gl5*GxqRSmZK)+>-TC^@EOrjIfuklE1;NAw#IA$d)SYA{ zlwAY0m35L;PXkJk7}6@x_Dyb@d< zoJp-pY&_U&h+0B^f|NDm6;&Iz9zAvT;^3{3U(#&m%v^W4DM@Um58QRnO(Wv>%+Gl< zGjno+H3RtiGc$!Y-=5rDp`T`Jo@i95+Ei1jO@qpxl&fr7o5^M?M@3JHR93CkWVIEE zJYTa|7}%a?bGGkZN>8QKlVna(Y1K>3OI0h>FPdLeEmp5P&HVGNpM1}ec)UE~$mQJ^ zNaEf96Taiar2D_hdG}hC zums0{kDDAbDb~$^N9fj5d;`8tm~S*&ly~n@$dlk71irsUqe09@LQ+x^Vm1 zM~Ym|g-%PEA`ys^lx7DfkE#=)SMUdPYjQNY^qVMlJBZ_hzmGzD4bkZ8Ks37cmuU3G z?HKgP8jEJ!jYY+aCLvW~%%r&BGy!S>1ONfWA;9zI#d!Ds^Pm6z```WUpD`*N7oXwX zKmD&i{@Yhy{Rj5Zc=uLo5q@36aQUA+`R~63pNkK?dxjtFW>gDE=)k*oKd%nEt$;cD z9Lg-v;-)x(UOcbBD_%^>JCupXySJ^a_k6hUIvVW*`M1|cPC9qDS5@cz_RdJJb6@+$ zYRkwi=c)Fc)k`huBi9G}9qsmNODgkQvElofSqK;Ca<;a=R&9DXH2A(_hkbRmW$>o6 z&u*_?VaXZ!2j_|Q#_BSQjwx{WL1rdmv)S9L+N&OZIC#dw(}*4p51w`G#`S(@WN7dwj(zs(YU|*Lqu0Kx;^nMl_6%>@*Kd6?&`V0W6oAb z4Q`Ut`Ho{}d-dQ4&U5z0ic(A7!;c0pINI!MEVH-*#tfzpC!B9NwzjXpiDw;q?W?Nu za6@|9TdONA#)r2CPdl3JD=Q34fuBDxVw7%-^f+4_8{5kt-o}Y7?HlaNaWl_jEK4j} zoO;H&$G)T@g)Q(Y?t`2Vfw%h5Bq;+3C;>_o1SZ1NpmYt~ibbIN`u0o3Cv!Vz?>;~H zx4q@ZGWVry-*sx~+s2)<>ZUEd-@oO^qV~CO%&b0teb=S3uDs6Kt=EUPI+wpc@9$>s zIM!EnwBRkBea4DkT-kP_q$9mCWus&0wR4vD)Ap(DomV!VF(1^ns_SlF-g&CzhsI|0 zYad^2=qm1*yDfR+zH6_Y&F!4E`}x|dLwkNwax`n-%z8)figyZjC9awN@|`PnCl>72 zy_vZFlRNEKSN3KeNNODXp!LGSL;Bt7*AMlqJXo|lxq4c~jcc#}$nwLq#>9;m2OG|n zAJes}YOY*saa!Ne?~Jd$d9L~Bl6^UiNvl8m+493VZ7Eyh*IXHTqi^X6!&{oI-B-7t zEk2a7S5tebr=fFkYxWxnl@~AXIKA-gxy_o5r?1rZlpdbbqTYD&V#8_c!MQC78;%@Z z^MfM0e!aTn`qh>*D~@FCN#3H^i31%61SS9iV^!h6T3CD#!DFbi#uCq}aHOXj@PDkp zp_@Brj($!RiWn6RUrs!s-A@r&v*+JB$gzCSL1_2S1??On@Pi8w5JkX;cK@|kHmRhK zVCVB{hSCm!cb}6DzbS}Z3<%#o1G8xQvFfB@8s0DqrUdiwr}i5=m~Ht3K4!V|(XlS> zJc=sEy#4I?hMh{gt|vl&8D4xW=Ebk=zWiw@c=4geh{m@k{%~^cnR5g0p748d%n)sv zAaHRe=T1!((C&@EyZ6B=KyJUBXPQXPOJ)gm`UD{Xc=v(N0A_s15D0DH-SgjqQXj4O z65+Ar^6sg6_gh*8diTFsLiFwz{5|O1!A)PjPgpD#9)VtV&(QF*s9 z!2D4xCfq1=JALyM+!bowGxiwe?$f^0Y4JdiQ zK{<#(lqf9)Hy{8A00MvjAOHv`4gp_IJn-%nHwhHh;Zb?_;le{I*+go-aP=d=^8)Wa zayjQ@r9jEQ3jn?Q055DPHYx(3chCH#>QL$3&*K-yJgoxHL;h$UmQv@BIE!7W^LCEm zSd1UdRwqVkW)r9-!m4*qMK_2E@&`)($;U915ml5rOM;jne~QXKxs)|yn#R4*ZxoD< z(9RS3-B){Ip)ilo7Gxij$sob;?yXj#&GYU({lYv#J21U_mdIdYi3=vq_T5YA9@_^i ztDBE|f%_w}2fh3JoVvz_+`1jL&6{%@HZL+$_3k}*_vinW=-o5Cd(gZ0qjzr~_0~#| zL6mndNJq$%;2#9OKj__i;L99<-n|bbC;}IZp-H~ORF4#9-t-Gkme=-t!5om?rh z@7$rlsF>mmfD)iYK|qmHgMtOP6^j7q-Gkn}VkbXzT=58uRfU5WyT_IYnxJ>jt>61{ z`$6wsWV(Rs86hw#?_MgeJ=po4QU4?LG{CzD-hI9)axn;&-n|Z~qHe})o0^K_Gb`Iu zBK3NNcJT;+-hH|ul$!XV)w`#1u;tUarBG5O=3zLrOd#6VOw1OQPih98i5EJB2QTZpAvSuvg*VAkvcV1`%@7|Yj&v~TGe&F3RcLzl8z69HK ztu2dc>+4vi{igbcCWdJ5&AX@S-EZBriFusVC@7RT-RVw!0XgEdz80Rn&kAOHve0)T*$5b)*1gWkQ8#$Snj9hG+INC z;|Jb-<;PRgT_$3BE^=!n>#H z-Fxuv=j^#(FfFQnWUNP!c5@)%_^Z4cd7M-5tB$bHSq3%cdrD! z`$)Lfpbhd60KNNht#?mjhRdgOOS|QL*13RpFZe};f&EDZ@a~`WBnmNyB+DL3Z2EBWN#S9#XJ>Fx`yXQwR0vC*-N&N88E!im1s~SHkpm#rh#wrq8 zI@Xmo+y~IRkA#7g*arW+d(gWF-aTe|cXc~2a5Qgkb9B9X{!i7JK<}P?OEAp8D-fDe z-l0g)yUzu^d)h~z>>EHRK!Z}~2b6?p&}=}7hK$e;C<)P^*?znvY&XM5X}m9(ebW%)2i^DwOag z=-o%;hsQW?6zJWDQtv()hgmrIkh8To=x}h0-D87Yz@nDmm$xFx3M=nk3@a*#0Vc>F zDEY05qydGtSglgljD@=PG@H5hIl=qFLZQuE`rL(YwF><-JJQA^Fy4JKgGG*3hxP8w zob9_0R!^0qcQ2K9Pu08k;N9QfPxS5?-aY8ugWf&4y#>8{f&?GSUJ8W*Ja}{qP@-eQ zr^rT$FB)nK^zK8AFw_qS00O=U_~+e&-aYW{fp>4U4)c%MAv2}CLz#HId(gWFy?ftp zB`=TcJ9jAHg`nsmpd<>5mlII(0z~w1BA_JNF>opv0nob#y?X^uf9Sfx5g4lq2k71N zFAn@!zTAG$yI1(77uN2N%Db1!YY%q5u%Z(FlLPM_c=wUayGN)1WvCI#z1~r2+5W=O-0nW6ll`H6eV%2WJ*TK+2jijcYIT(|Gj2yZ2?>a~`qL L2*fwBdH4Sh_9QQ4 literal 0 HcmV?d00001 diff --git a/package/firmware/ipq-wifi/board-linksys_ea8300.qca9888 b/package/firmware/ipq-wifi/board-linksys_ea8300.qca9888 new file mode 100644 index 0000000000000000000000000000000000000000..e3c2039924f483ecc3679ee005c0a1f73c6bbcc4 GIT binary patch literal 48628 zcmeHQeNYo;8h?X&qLs>q4*_vSM6<*sgoM^DM)}aQIT8_V@Ql?~1TCxxRFr~ITko!w zILpULsbEQqsXAVZl<6@yUQ5U8bUL*+wR3ZGGuN5>=l;Gw`iJK@&dr>;cX!!j3A>m; zg7NY^n0KFj-sgEge((Fj?!LdQySA3;%N*81qfKAFvuyV^bnMtMgr%i`OA#u;pF<~G zH@DO_=nfrg(AU;CwCEe^HXHe~L(MhE>$p>sS=Ux`yrHJ)#OB6^rlYMLt@^_?wApCX z*VG?V;WBb?c{v5o4X9M=qCM@s>OY@DDD9s(;~+vO-$=j;Ldggvm^me3(E{!eEVZ?W zD+(dA*?j-rJ!DH=hI~F>iTGKN8XOVw`9Fd^d-AhYjH2bQp+As`gE0Hvs)6iT7s0|)>DfIzqi zTaQ4!dLG5!FSNN6pf={ z{3FUzH0FB`fA(PC>%NPA|K8rVeGZ3xJB^Z)6YmM$bpE=vxw)(HN$TPU4<9{B!~Xkt6%|2)3-OloX-NNTw|#E!`uyz?L_=N4O7H zc2Ph~MuSdE3^Aya-zAy$$r4J++i$*n(aC2XY4V6&S^^G{}C6S>K-$ zN&E$!t6`9@W-ya0SAa{ja2b=cL_kR~6+DGhsT{evJ69XqKRo{B-N3y?u=cp}*-_@A zvyI-Bp>=tgerr8louOlIFrCgux`Hb7eByF5F6(Z(^dT0cp)`p7l7{opIw(J5`7aapM|rA){k#H`DBN&}M&=Ji}}c)54iN zzjJjm?N%FIj0@>xPFZ)-n@6vBx?J_lKC6Kb$k%9*$IJFHuX6$H6<0TN*1Ch&(bcF52nN_qA*WhM4tQGVNqu1DXmDfw`_ zG6fEW6F^A;m?>sJX$l+)CxDUyFkl7*W)~a{iykzSzyp~;^^upDlqg{sP>{pU)pL?5n zesM16aH`{qmwDHAKCfxTf&LzATfuADj-=wT%ct4m*1SV$RsA3AyHIjEyH@?ug&}8m z$+^|_sm|;Dt?rFYxv!+#zxEz*>zlJ*C3f5y>+n=|7o1t{7#gnY*>qOZqIP^c(AsHl zU-NRB?cK}H&dsN=-_EaZR(2J*R@STcz3;8*D}HnR>xAQU_pY;RUrpbUv}N%9I=0lc zp((BUkDqmXRPZ)=BKeT#gTuX+GnyuK73)6GLG52rvHXSe{d?b`Pf`sjRbPy};W3^e z8`Up=b-lJ{%Uk)!)zw$Kn$H?*R#g(4#s}Nnl`d1G`o*69qwca(S|-yu1GJC@2mk^x zjzGeKg^PZ+IC06+XO<;ByF8gtr=+H(XJoAu@6x!-e>n-YTVtK=drR+}sWOr4*5%=U zYjfA+tX;Dvcg-G@$nA{gP)54cTDA9JeM|dWoxKCYH^y%L>CT-yV*R1kGZ()VrWM3$ z^^2w#iJj_=rj102I#Cp~`_M)2XJ1QG|5J&ul<9RW5hY@E%mo98jV}ZqJa};b{{4ST zB&h!(J+HRNInErMN%M~o5$1N;#v5DnG>uBGLf4L5if2VZRtY4S+BtOE= zov>FY?9SP%9DDa4tgB~x-yIklzItP1Z2Z=jUw!l4-S9I|_M~VeV&o)uQuF~4E^QSf z!n*RE*;%d*zJZU;$d`zL6U6U>+SQ%nPAIV@H0Z$Gp^k8%8~B(KDa*m zhuhyO>0Hf1cZ4Y^>Rca$buUaK(LU8*uxd0qU8H6}pnQ!+st4Mm*Guh6dg`N8BAd)M zWZP5Gwny6tJ83uA?b}e%qawmWS_~F@k<9%yk3}BebFH9HPebWxDCMM^(g{+%-L##k zR6lQep4g(^cbWT{UVgOx?nS%Yi1F?ZpOo;R?MKq-_~fDa%52mk`%A^^Pma1jgm#{=))Pj2@sBixsBIr+VL z@}_J;yg8F79CI4WAfNI|WO(=fW(4u>DX|R}t-NaRI~XaU{Ww+d4cxcuO#U#F&L0-Y zk7wTffbeYyfp<@7wc3w0LTbQ|Nyqe3i=gvRPRyKg^JS1ra0)O0>HZm-hI5U0qB4HA^^O5gr;-iMcRF$%$~jf zu|-(Q^g2Y^{gQ~)5x=t-dLAwUz`G9@vH9@_-n~u>-zkV)3~~^my1AfnX*NC%-TqI; z{HzM7B^D3>-hFg=`O)RwZ&12kEmX?bfGORQ=QoQ?o$>>P+0;%1<+RbLEk5req z&q?Kw5Z1iKBGm)D`>A%Rk5r!>@17?z7LC~kCp>&V$gN5hs<6dyTx~8Y`!@DoV z7b$ak-~Ex=TJCGy!u#&;{axhU+kkhEQ32jP27woN-@S-L;28bAQ>Y<;wz38&DPsdU zfB+x>2t*eF;N8z2-}vO+4}`?K7w-or{7N)=_g)mZ>&}-~jbcMA#(Y14Ucp!E_ti?m zwEnO_{=D$+{jHgo+Cq7T!gK8>dG`YQem#CW#z?-9>hP1$&kCd#LFfB1G52)#D^@uY z-gmD-@VaLkT(ui>!J8Mv-n1buoMsh-9U@4f_Igv^O|-%u-g-+jurBJbYa2k*NF z-hFzyc#R9Zdl8Ai5eO6kER;1sNg10!PV`X<)CC$K00;mAkwXA@_p`?mc=y6x--LMc zH(d!Z#V4LH?>_LAc?0n7`2q8fmL)JsSPkVFN(j7rJ@D??8%(FOk*=T$J)gMTjLW*4 zE`5jvX($b1KV|xyZS*c`qw5-T$=N|yXK2}*Oqa8nwoyjb>*`_7S>b*6@V@(*|2{?k z?gMI=c?5)9KnYM%Kp^a?p->K(;}!wn-2?AFZYMuw<_jFHO?Cp%AT>5U$3NdYhNJVo6S<4Tl&Jnw^*chB|X-LV|Kjz Y3=Rt&nS*)vCPAN`MyjX(-@N<(0qkJ6aR2}S literal 0 HcmV?d00001 diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network index d8a5697361..6a7b09cc60 100755 --- a/target/linux/ipq40xx/base-files/etc/board.d/02_network +++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network @@ -29,7 +29,8 @@ ipq40xx_setup_interfaces() "0u@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" ;; avm,fritzbox-4040|\ - linksys,ea6350v3) + linksys,ea6350v3|\ + linksys,ea8300) ucidef_set_interfaces_lan_wan "eth0" "eth1" ucidef_add_switch "switch0" \ "0u@eth0" "1:lan" "2:lan" "3:lan" "4:lan" diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index af84e4e84a..1e64b93a46 100644 --- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -93,7 +93,6 @@ ath10kcal_is_caldata_valid() { board=$(board_name) - case "$FIRMWARE" in "ath10k/cal-pci-0000:01:00.0.bin") case "$board" in @@ -115,6 +114,11 @@ case "$FIRMWARE" in /usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x212 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \ /usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x212 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") ;; + linksys,ea8300) + ath10kcal_extract "ART" 36864 12064 + # OEM assigns 4 sequential MACs + ath10kcal_patch_mac_crc $(macaddr_setbit_la $(macaddr_add "$(cat /sys/class/net/eth0/address)" 4)) + ;; openmesh,a62) ath10kcal_extract "0:ART" 36864 12064 ;; @@ -156,6 +160,10 @@ case "$FIRMWARE" in ath10kcal_extract "ART" 4096 12064 ath10kcal_patch_mac_crc $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +2) ;; + linksys,ea8300) + ath10kcal_extract "ART" 4096 12064 + ath10kcal_patch_mac_crc $(macaddr_add "$(cat /sys/class/net/eth0/address)" 2) + ;; meraki,mr33) ath10kcal_ubi_extract "ART" 4096 12064 ath10kcal_is_caldata_valid "202f" || ath10kcal_extract "ART" 4096 12064 @@ -209,6 +217,10 @@ case "$FIRMWARE" in ath10kcal_extract "ART" 20480 12064 ath10kcal_patch_mac_crc $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +3) ;; + linksys,ea8300) + ath10kcal_extract "ART" 20480 12064 + ath10kcal_patch_mac_crc $(macaddr_add "$(cat /sys/class/net/eth0/address)" 3) + ;; meraki,mr33) ath10kcal_ubi_extract "ART" 20480 12064 ath10kcal_is_caldata_valid "202f" || ath10kcal_extract "ART" 20480 12064 diff --git a/target/linux/ipq40xx/base-files/etc/init.d/bootcount b/target/linux/ipq40xx/base-files/etc/init.d/bootcount index abde12412a..f2d76f125f 100755 --- a/target/linux/ipq40xx/base-files/etc/init.d/bootcount +++ b/target/linux/ipq40xx/base-files/etc/init.d/bootcount @@ -10,7 +10,8 @@ start() { [ -n "$(fw_printenv bootcount changed 2>/dev/null)" ] &&\ echo -e "bootcount\nchanged\n" | /usr/sbin/fw_setenv -s - ;; - linksys,ea6350v3) + linksys,ea6350v3|\ + linksys,ea8300) mtd resetbc s_env || true ;; esac diff --git a/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh b/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh index ce5c1fc4bf..fc64441e1a 100644 --- a/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh +++ b/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh @@ -9,6 +9,11 @@ preinit_set_mac_address() { ip link set dev eth0 address $(macaddr_add "$base_mac" +1) ip link set dev eth1 address $(macaddr_add "$base_mac" +3) ;; + linksys,ea8300) + base_mac=$(mtd_get_mac_ascii devinfo hw_mac_addr) + ip link set dev eth0 address "${base_mac}" + ip link set dev eth1 address $(macaddr_add "${base_mac}" 1) + ;; meraki,mr33) mac_lan=$(get_mac_binary "/sys/bus/i2c/devices/0-0050/eeprom" 102) [ -n "$mac_lan" ] && ip link set dev eth0 address "$mac_lan" diff --git a/target/linux/ipq40xx/base-files/lib/preinit/06_set_preinit_iface_ipq40xx.sh b/target/linux/ipq40xx/base-files/lib/preinit/06_set_preinit_iface_ipq40xx.sh index 578ddbe4c4..be4b6322cb 100644 --- a/target/linux/ipq40xx/base-files/lib/preinit/06_set_preinit_iface_ipq40xx.sh +++ b/target/linux/ipq40xx/base-files/lib/preinit/06_set_preinit_iface_ipq40xx.sh @@ -7,6 +7,7 @@ set_preinit_iface() { asus,rt-ac58u| \ avm,fritzbox-4040| \ glinet,gl-b1300| \ + linksys,ea8300| \ meraki,mr33| \ zyxel,nbg6617) ifname=eth0 diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh index 84b123335c..e62d16c449 100644 --- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh @@ -49,7 +49,7 @@ platform_do_upgrade() { 8dev,jalapeno |\ alfa-network,ap120c-ac |\ avm,fritzbox-7530 |\ - avm,fritzrepeater-3000|\ + avm,fritzrepeater-3000 |\ qxwlan,e2600ac-c2) nand_do_upgrade "$ARGV" ;; @@ -62,18 +62,19 @@ platform_do_upgrade() { CI_KERNPART="linux" nand_do_upgrade "$1" ;; - linksys,ea6350v3) + linksys,ea6350v3 |\ + linksys,ea8300) platform_do_upgrade_linksys "$ARGV" ;; + meraki,mr33) + CI_KERNPART="part.safe" + nand_do_upgrade "$1" + ;; openmesh,a42 |\ openmesh,a62) PART_NAME="inactive" platform_do_upgrade_openmesh "$ARGV" ;; - meraki,mr33) - CI_KERNPART="part.safe" - nand_do_upgrade "$1" - ;; zyxel,nbg6617) zyxel_do_upgrade "$1" ;; diff --git a/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4019-linksys_ea8300.dts b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4019-linksys_ea8300.dts new file mode 100644 index 0000000000..cfc3037fb2 --- /dev/null +++ b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4019-linksys_ea8300.dts @@ -0,0 +1,399 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +/* + * Device Tree Source for Linksys EA8300 (Dallas) + * + * Copyright (C) 2019 Jeff Kletsky + * + */ + +/dts-v1/; + +#include "qcom-ipq4019.dtsi" +#include +#include +#include + +/ { + model = "Linksys EA8300 (Dallas)"; + compatible = "linksys,ea8300", "qcom,ipq4019"; + + + aliases { + led-boot = &led_wps_amber; + led-failsafe = &led_wps; + led-running = &led_linksys; + led-upgrade = &led_world; + serial0 = &blsp1_uart1; + }; + + + leds { + compatible = "gpio-leds"; + + // Retain node names from running OEM on EA8300 + + // Front panel LEDs, top to bottom + + led_plug: diag { + label = "ea8300:amber:plug"; + gpios = <&tlmm 47 GPIO_ACTIVE_HIGH>; + }; + + led_world: internet { + label = "ea8300:amber:world"; + gpios = <&tlmm 49 GPIO_ACTIVE_HIGH>; + }; + + led_wps: wps { + label = "ea8300:white:wps"; + gpios = <&tlmm 46 GPIO_ACTIVE_HIGH>; + }; + + led_wps_amber: wps_amber { + label = "ea8300:amber:wps"; + gpios = <&tlmm 22 GPIO_ACTIVE_HIGH>; + panic-indicator; + }; + + led_linksys: pwr { + label = "ea8300:white:linksys"; + gpios = <&tlmm 45 GPIO_ACTIVE_HIGH>; + }; + + // On back panel, above USB socket + + led_usb: usb { + label = "ea8300:green:usb"; + gpios = <&tlmm 61 GPIO_ACTIVE_LOW>; + trigger-sources = <&usb3_port1>, <&usb3_port2>, + <&usb2_port1>; + linux,default-trigger = "usbport"; + }; + }; + + + keys { + compatible = "gpio-keys"; + + button@0 { + label = "reset"; + linux,code = ; + gpios = <&tlmm 50 GPIO_ACTIVE_LOW>; + }; + + button@1 { + label = "wps"; + linux,code = ; + gpios = <&tlmm 18 GPIO_ACTIVE_LOW>; + }; + }; + + + // + // OEM U-Boot provides either + // init=/sbin/init rootfstype=ubifs ubi.mtd=11,2048 \ + // root=ubi0:ubifs rootwait rw + // or the same with ubi.mtd=13,2048 + // + + chosen { + bootargs-append = " root=/dev/ubiblock0_0 rootfstype=squashfs ro"; + }; + + + memory { + device_type = "memory"; + reg = <0x80000000 0x10000000>; + }; + + + soc { + rng@22000 { + status = "okay"; + }; + + mdio@90000 { + status = "okay"; + }; + + ess-psgmii@98000 { + status = "okay"; + }; + + tcsr@1949000 { + compatible = "qcom,tcsr"; + reg = <0x1949000 0x100>; + qcom,wifi_glb_cfg = ; + }; + + tcsr@194b000 { + compatible = "qcom,tcsr"; + reg = <0x194b000 0x100>; + qcom,usb-hsphy-mode-select = ; + }; + + ess_tcsr@1953000 { + compatible = "qcom,tcsr"; + reg = <0x1953000 0x1000>; + qcom,ess-interface-select = ; + }; + + tcsr@1957000 { + compatible = "qcom,tcsr"; + reg = <0x1957000 0x100>; + qcom,wifi_noc_memtype_m0_m2 = ; + }; + + usb2@60f8800 { + status = "okay"; + + dwc3@6000000 { + #address-cells = <1>; + #size-cells = <0>; + + usb2_port1: port@1 { + reg = <1>; + #trigger-source-cells = <0>; + }; + }; + }; + + usb3@8af8800 { + status = "okay"; + + dwc3@8a00000 { + #address-cells = <1>; + #size-cells = <0>; + + usb3_port1: port@1 { + reg = <1>; + #trigger-source-cells = <0>; + }; + + usb3_port2: port@2 { + reg = <2>; + #trigger-source-cells = <0>; + }; + }; + }; + + crypto@8e3a000 { + status = "okay"; + }; + + watchdog@b017000 { + status = "okay"; + }; + + ess-switch@c000000 { + status = "okay"; + }; + + edma@c080000 { + status = "okay"; + }; + }; +}; + + +&blsp_dma { + status = "okay"; +}; + +&blsp1_uart1 { + status = "okay"; + pinctrl-0 = <&serial_0_pins>; + pinctrl-names = "default"; + +}; + +&cryptobam { + status = "okay"; +}; + +&nand { + status = "okay"; + + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + + nand@0 { + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "sbl1"; + reg = <0x0 0x100000>; + read-only; + }; + + partition@100000 { + label = "mibib"; + reg = <0x100000 0x100000>; + read-only; + }; + + partition@200000 { + label = "qsee"; + reg = <0x200000 0x100000>; + read-only; + }; + + partition@300000 { + label = "cdt"; + reg = <0x300000 0x80000>; + read-only; + }; + + partition@380000 { + label = "appsblenv"; + reg = <0x380000 0x80000>; + read-only; + }; + + partition@400000 { + label = "ART"; + reg = <0x400000 0x80000>; + read-only; + }; + + partition@480000 { + label = "appsbl"; + reg = <0x480000 0x200000>; + read-only; + }; + + partition@680000 { + label = "u_env"; + reg = <0x680000 0x80000>; + // writable -- U-Boot environment + }; + + partition@700000 { + label = "s_env"; + reg = <0x700000 0x40000>; + // writable -- Boot counter records + }; + + partition@740000 { + label = "devinfo"; + reg = <0x740000 0x40000>; + read-only; + }; + + partition@780000 { + label = "kernel"; + reg = <0x780000 0x5800000>; + }; + + partition@a80000 { + label = "rootfs"; + reg = <0xa80000 0x5500000>; + }; + + partition@5f80000 { + label = "alt_kernel"; + reg = <0x5f80000 0x5800000>; + }; + + partition@6280000 { + label = "alt_rootfs"; + reg = <0x6280000 0x5500000>; + }; + + partition@b780000 { + label = "sysdiag"; + reg = <0xb780000 0x100000>; + read-only; + }; + + partition@b880000 { + label = "syscfg"; + reg = <0xb880000 0x4680000>; + read-only; + }; + }; + }; +}; + +&pcie0 { + status = "okay"; + + perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>; + wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>; + + bridge@0,0 { + reg = <0x00000000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + ranges; + + wifi2: wifi@1,0 { + compatible = "qcom,ath10k"; + reg = <0x00010000 0 0 0 0>; + }; + }; +}; + +&qpic_bam { + status = "okay"; +}; + +&tlmm { + serial_0_pins: serial0-pinmux { + pins = "gpio16", "gpio17"; + function = "blsp_uart0"; + bias-disable; + }; + + nand_pins: nand_pins { + pullups { + pins = "gpio53", "gpio58", "gpio59"; + function = "qpic"; + bias-pull-up; + }; + + // gpio61 controls led_usb + + pulldowns { + pins = "gpio55", "gpio56", "gpio57", + "gpio60", "gpio62", "gpio63", + "gpio64", "gpio65", "gpio66", + "gpio67", "gpio68", "gpio69"; + function = "qpic"; + bias-pull-down; + }; + }; +}; + +&usb2_hs_phy { + status = "okay"; +}; + +&usb3_hs_phy { + status = "okay"; +}; + +&usb3_ss_phy { + status = "okay"; +}; + +&wifi0 { + status = "okay"; + qcom,ath10k-calibration-variant = "linksys-ea8300-fcc"; +}; + +&wifi1 { + status = "okay"; + ieee80211-freq-limit = <5170000 5330000>; + qcom,ath10k-calibration-variant = "linksys-ea8300-fcc"; +}; + +&wifi2 { + status = "okay"; + ieee80211-freq-limit = <5490000 5835000>; + qcom,ath10k-calibration-variant = "linksys-ea8300-fcc"; +}; diff --git a/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-linksys_ea8300.dts b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-linksys_ea8300.dts new file mode 100644 index 0000000000..cfc3037fb2 --- /dev/null +++ b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-linksys_ea8300.dts @@ -0,0 +1,399 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +/* + * Device Tree Source for Linksys EA8300 (Dallas) + * + * Copyright (C) 2019 Jeff Kletsky + * + */ + +/dts-v1/; + +#include "qcom-ipq4019.dtsi" +#include +#include +#include + +/ { + model = "Linksys EA8300 (Dallas)"; + compatible = "linksys,ea8300", "qcom,ipq4019"; + + + aliases { + led-boot = &led_wps_amber; + led-failsafe = &led_wps; + led-running = &led_linksys; + led-upgrade = &led_world; + serial0 = &blsp1_uart1; + }; + + + leds { + compatible = "gpio-leds"; + + // Retain node names from running OEM on EA8300 + + // Front panel LEDs, top to bottom + + led_plug: diag { + label = "ea8300:amber:plug"; + gpios = <&tlmm 47 GPIO_ACTIVE_HIGH>; + }; + + led_world: internet { + label = "ea8300:amber:world"; + gpios = <&tlmm 49 GPIO_ACTIVE_HIGH>; + }; + + led_wps: wps { + label = "ea8300:white:wps"; + gpios = <&tlmm 46 GPIO_ACTIVE_HIGH>; + }; + + led_wps_amber: wps_amber { + label = "ea8300:amber:wps"; + gpios = <&tlmm 22 GPIO_ACTIVE_HIGH>; + panic-indicator; + }; + + led_linksys: pwr { + label = "ea8300:white:linksys"; + gpios = <&tlmm 45 GPIO_ACTIVE_HIGH>; + }; + + // On back panel, above USB socket + + led_usb: usb { + label = "ea8300:green:usb"; + gpios = <&tlmm 61 GPIO_ACTIVE_LOW>; + trigger-sources = <&usb3_port1>, <&usb3_port2>, + <&usb2_port1>; + linux,default-trigger = "usbport"; + }; + }; + + + keys { + compatible = "gpio-keys"; + + button@0 { + label = "reset"; + linux,code = ; + gpios = <&tlmm 50 GPIO_ACTIVE_LOW>; + }; + + button@1 { + label = "wps"; + linux,code = ; + gpios = <&tlmm 18 GPIO_ACTIVE_LOW>; + }; + }; + + + // + // OEM U-Boot provides either + // init=/sbin/init rootfstype=ubifs ubi.mtd=11,2048 \ + // root=ubi0:ubifs rootwait rw + // or the same with ubi.mtd=13,2048 + // + + chosen { + bootargs-append = " root=/dev/ubiblock0_0 rootfstype=squashfs ro"; + }; + + + memory { + device_type = "memory"; + reg = <0x80000000 0x10000000>; + }; + + + soc { + rng@22000 { + status = "okay"; + }; + + mdio@90000 { + status = "okay"; + }; + + ess-psgmii@98000 { + status = "okay"; + }; + + tcsr@1949000 { + compatible = "qcom,tcsr"; + reg = <0x1949000 0x100>; + qcom,wifi_glb_cfg = ; + }; + + tcsr@194b000 { + compatible = "qcom,tcsr"; + reg = <0x194b000 0x100>; + qcom,usb-hsphy-mode-select = ; + }; + + ess_tcsr@1953000 { + compatible = "qcom,tcsr"; + reg = <0x1953000 0x1000>; + qcom,ess-interface-select = ; + }; + + tcsr@1957000 { + compatible = "qcom,tcsr"; + reg = <0x1957000 0x100>; + qcom,wifi_noc_memtype_m0_m2 = ; + }; + + usb2@60f8800 { + status = "okay"; + + dwc3@6000000 { + #address-cells = <1>; + #size-cells = <0>; + + usb2_port1: port@1 { + reg = <1>; + #trigger-source-cells = <0>; + }; + }; + }; + + usb3@8af8800 { + status = "okay"; + + dwc3@8a00000 { + #address-cells = <1>; + #size-cells = <0>; + + usb3_port1: port@1 { + reg = <1>; + #trigger-source-cells = <0>; + }; + + usb3_port2: port@2 { + reg = <2>; + #trigger-source-cells = <0>; + }; + }; + }; + + crypto@8e3a000 { + status = "okay"; + }; + + watchdog@b017000 { + status = "okay"; + }; + + ess-switch@c000000 { + status = "okay"; + }; + + edma@c080000 { + status = "okay"; + }; + }; +}; + + +&blsp_dma { + status = "okay"; +}; + +&blsp1_uart1 { + status = "okay"; + pinctrl-0 = <&serial_0_pins>; + pinctrl-names = "default"; + +}; + +&cryptobam { + status = "okay"; +}; + +&nand { + status = "okay"; + + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + + nand@0 { + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "sbl1"; + reg = <0x0 0x100000>; + read-only; + }; + + partition@100000 { + label = "mibib"; + reg = <0x100000 0x100000>; + read-only; + }; + + partition@200000 { + label = "qsee"; + reg = <0x200000 0x100000>; + read-only; + }; + + partition@300000 { + label = "cdt"; + reg = <0x300000 0x80000>; + read-only; + }; + + partition@380000 { + label = "appsblenv"; + reg = <0x380000 0x80000>; + read-only; + }; + + partition@400000 { + label = "ART"; + reg = <0x400000 0x80000>; + read-only; + }; + + partition@480000 { + label = "appsbl"; + reg = <0x480000 0x200000>; + read-only; + }; + + partition@680000 { + label = "u_env"; + reg = <0x680000 0x80000>; + // writable -- U-Boot environment + }; + + partition@700000 { + label = "s_env"; + reg = <0x700000 0x40000>; + // writable -- Boot counter records + }; + + partition@740000 { + label = "devinfo"; + reg = <0x740000 0x40000>; + read-only; + }; + + partition@780000 { + label = "kernel"; + reg = <0x780000 0x5800000>; + }; + + partition@a80000 { + label = "rootfs"; + reg = <0xa80000 0x5500000>; + }; + + partition@5f80000 { + label = "alt_kernel"; + reg = <0x5f80000 0x5800000>; + }; + + partition@6280000 { + label = "alt_rootfs"; + reg = <0x6280000 0x5500000>; + }; + + partition@b780000 { + label = "sysdiag"; + reg = <0xb780000 0x100000>; + read-only; + }; + + partition@b880000 { + label = "syscfg"; + reg = <0xb880000 0x4680000>; + read-only; + }; + }; + }; +}; + +&pcie0 { + status = "okay"; + + perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>; + wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>; + + bridge@0,0 { + reg = <0x00000000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + ranges; + + wifi2: wifi@1,0 { + compatible = "qcom,ath10k"; + reg = <0x00010000 0 0 0 0>; + }; + }; +}; + +&qpic_bam { + status = "okay"; +}; + +&tlmm { + serial_0_pins: serial0-pinmux { + pins = "gpio16", "gpio17"; + function = "blsp_uart0"; + bias-disable; + }; + + nand_pins: nand_pins { + pullups { + pins = "gpio53", "gpio58", "gpio59"; + function = "qpic"; + bias-pull-up; + }; + + // gpio61 controls led_usb + + pulldowns { + pins = "gpio55", "gpio56", "gpio57", + "gpio60", "gpio62", "gpio63", + "gpio64", "gpio65", "gpio66", + "gpio67", "gpio68", "gpio69"; + function = "qpic"; + bias-pull-down; + }; + }; +}; + +&usb2_hs_phy { + status = "okay"; +}; + +&usb3_hs_phy { + status = "okay"; +}; + +&usb3_ss_phy { + status = "okay"; +}; + +&wifi0 { + status = "okay"; + qcom,ath10k-calibration-variant = "linksys-ea8300-fcc"; +}; + +&wifi1 { + status = "okay"; + ieee80211-freq-limit = <5170000 5330000>; + qcom,ath10k-calibration-variant = "linksys-ea8300-fcc"; +}; + +&wifi2 { + status = "okay"; + ieee80211-freq-limit = <5490000 5835000>; + qcom,ath10k-calibration-variant = "linksys-ea8300-fcc"; +}; diff --git a/target/linux/ipq40xx/image/Makefile b/target/linux/ipq40xx/image/Makefile index ae146cdc54..3a9b58de4f 100644 --- a/target/linux/ipq40xx/image/Makefile +++ b/target/linux/ipq40xx/image/Makefile @@ -248,6 +248,21 @@ define Device/linksys_ea6350v3 endef TARGET_DEVICES += linksys_ea6350v3 +define Device/linksys_ea8300 + $(call Device/FitzImage) + DEVICE_TITLE := Linksys EA8300 (Dallas) + DEVICE_DTS := qcom-ipq4019-linksys_ea8300 + KERNEL_SIZE := 3072k + IMAGE_SIZE := 87040k + BLOCKSIZE := 128k + PAGESIZE := 2048 + UBINIZE_OPTS := -E 5 # EOD marks to "hide" factory sig at EOF + IMAGES := sysupgrade.bin factory.bin + IMAGE/factory.bin := append-kernel | pad-to $$$${KERNEL_SIZE} | append-ubi | linksys-image type=EA8300 + DEVICE_PACKAGES := uboot-envtools ath10k-firmware-qca9888-ct ipq-wifi-linksys_ea8300 kmod-usb-ledtrig-usbport +endef +TARGET_DEVICES += linksys_ea8300 + define Device/meraki_mr33 $(call Device/FitImage) DEVICE_DTS := qcom-ipq4029-mr33 diff --git a/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch index 6743f44b25..bb539155e9 100644 --- a/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -697,7 +697,29 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -697,7 +697,30 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ @@ -31,6 +31,7 @@ Signed-off-by: John Crispin + qcom-ipq4019-ap.dk04.1-c1.dtb \ + qcom-ipq4019-fritzbox-7530.dtb \ + qcom-ipq4019-fritzrepeater-3000.dtb \ ++ qcom-ipq4019-linksys_ea8300.dtb \ + qcom-ipq4019-map-ac2200.dtb \ + qcom-ipq4019-qxwlan-e2600ac-c1.dtb \ + qcom-ipq4019-qxwlan-e2600ac-c2.dtb \ diff --git a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch index 57a5760806..a0386f6b66 100644 --- a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -785,11 +785,32 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -785,11 +785,33 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ @@ -34,6 +34,7 @@ Signed-off-by: John Crispin + qcom-ipq4019-a62.dtb \ + qcom-ipq4019-fritzbox-7530.dtb \ + qcom-ipq4019-fritzrepeater-3000.dtb \ ++ qcom-ipq4019-linksys_ea8300.dtb \ + qcom-ipq4019-map-ac2200.dtb \ + qcom-ipq4019-qxwlan-e2600ac-c1.dtb \ + qcom-ipq4019-qxwlan-e2600ac-c2.dtb \ -- 2.30.2