From 76e419288fc237666faebb6548c2da92468a6133 Mon Sep 17 00:00:00 2001 From: Kristian Skramstad Date: Mon, 21 Aug 2023 17:45:36 +0200 Subject: [PATCH] ipq807x: add support for Netgear WAX620 ``` Specifications: * CPU: Qualcomm IPQ8072A, SoC Version: 2.0, Quad core Cortex-A53 1.6896 GHz * RAM: 1 GiB of DDR4 600 MHz * Flash: NAND 2x256 MiB (Macronix MX30UF2G18AC) * 4 RGB LEDs: Power, LAN, 2.4GHz and 5GHz * UART: Two 4-pin unpopulated headers under the LEDs. Use the header closest to LED 4 and 5. They are marked with a white stroke. TX RX GND, beginning from "4". 115200n8. Lan: * One 100/1000/2.5GBASE-T Gigabit Ethernet (QCA8081) Wlan: * 4x4 in 2.4GHz: 802.11b/g/n/ax * 4x4 in 5.0GHz: 802.11a/n/ac/ax * OFDM and OFDMA * Bidir and MU-MIMO * Internal antenna 3.1/4.3 dBi (2.4GHz/5GHz) Power: * PoE+ 802.3at/af 25.5W * DC 12V 2.5A ``` ``` Note: The OpenWrt image is setup with DHCP and not a static IP. 1. Download the OpenWrt initramfs image. Copy the image to a TFTP server 2. Connect to console on the AP, and connect the LAN port to your LAN 3. Stop auto boot to get to U-boot shell, interrupt the autoboot process by pressing '0' when prompted 4. Set active_fw in env # setenv active_fw 1 5. Transfer the initramfs image with TFTP # setenv serverip 192.168.1.10 (IP of TFTP server host) # setenv ipaddr 192.168.1.1 (IP used by the router for getting the image, must be in the same subnet as the TFTP host) # tftpboot openwrt-qualcommax-ipq807x-netgear_wax620-initramfs-uImage.itb 6. Reboot and load the image # bootm 7. SCP factory image to the AP # scp openwrt-qualcommax-ipq807x-netgear_wax620-squashfs-factory.ubi root@192.168.1.1:/tmp/ 8. Connect to device using SSH (use the LAN port) 9. Flash squashfs-factory.ubi from within the initramfs instance of OpenWRT Before you flash, please check your mtd partitions where mtdX is the right mtd rootfs partition. # cat /proc/mtd (To check MTD partitions) # ubiformat /dev/mtd19 -y -f /tmp/openwrt-qualcommax-ipq807x-netgear_wax620-squashfs-factory.ubi 10. Set active_fw to 0 # /usr/sbin/fw_setenv active_fw 0 11. Reboot the AP and your done # reboot ``` Signed-off-by: Kristian Skramstad --- .../uboot-envtools/files/qualcommax_ipq807x | 3 +- package/firmware/ipq-wifi/Makefile | 2 + .../arm64/boot/dts/qcom/ipq8072-wax620.dts | 201 ++++++++++++++++++ target/linux/qualcommax/image/ipq807x.mk | 14 ++ .../ipq807x/base-files/etc/board.d/01_leds | 3 + .../ipq807x/base-files/etc/board.d/02_network | 3 +- .../etc/hotplug.d/firmware/11-ath11k-caldata | 1 + .../base-files/lib/upgrade/platform.sh | 3 +- 8 files changed, 227 insertions(+), 3 deletions(-) create mode 100644 target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8072-wax620.dts diff --git a/package/boot/uboot-envtools/files/qualcommax_ipq807x b/package/boot/uboot-envtools/files/qualcommax_ipq807x index 297c727857..106ba47c08 100644 --- a/package/boot/uboot-envtools/files/qualcommax_ipq807x +++ b/package/boot/uboot-envtools/files/qualcommax_ipq807x @@ -10,7 +10,8 @@ board=$(board_name) case "$board" in dynalink,dl-wrx36|\ netgear,rax120v2|\ -netgear,wax218) +netgear,wax218|\ +netgear,wax620) idx="$(find_mtd_index 0:appsblenv)" [ -n "$idx" ] && \ ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x40000" "0x20000" "2" diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile index 2fb40bea3b..6dd2260fac 100644 --- a/package/firmware/ipq-wifi/Makefile +++ b/package/firmware/ipq-wifi/Makefile @@ -35,6 +35,7 @@ ALLWIFIBOARDS:= \ edimax_cax1800 \ netgear_rax120v2 \ netgear_wax218 \ + netgear_wax620 \ prpl_haze \ qnap_301w \ redmi_ax6 \ @@ -126,6 +127,7 @@ $(eval $(call generate-ipq-wifi-package,edgecore_eap102,Edgecore EAP102)) $(eval $(call generate-ipq-wifi-package,edimax_cax1800,Edimax CAX1800)) $(eval $(call generate-ipq-wifi-package,netgear_rax120v2,Netgear RAX120v2)) $(eval $(call generate-ipq-wifi-package,netgear_wax218,Netgear WAX218)) +$(eval $(call generate-ipq-wifi-package,netgear_wax620,Netgear WAX620)) $(eval $(call generate-ipq-wifi-package,qnap_301w,QNAP 301w)) $(eval $(call generate-ipq-wifi-package,prpl_haze,prpl Haze)) $(eval $(call generate-ipq-wifi-package,redmi_ax6,Redmi AX6)) diff --git a/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8072-wax620.dts b/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8072-wax620.dts new file mode 100644 index 0000000000..d1c3245c8b --- /dev/null +++ b/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8072-wax620.dts @@ -0,0 +1,201 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +/dts-v1/; + +#include "ipq8074.dtsi" +#include "ipq8074-hk-cpu.dtsi" +#include "ipq8074-ess.dtsi" +#include +#include + +/ { + model = "Netgear WAX620"; + compatible = "netgear,wax620", "qcom,ipq8074"; + + aliases { + serial0 = &blsp1_uart5; + ethernet0 = &dp6; + led-boot = &led_system_blue; + led-failsafe = &led_system_red; + led-running = &led_system_green; + led-upgrade = &led_system_blue; + }; + + chosen { + stdout-path = "serial0:115200n8"; + /* + * Netgear's U-Boot adds "ubi.mtd=rootfs root=mtd:ubi_rootfs" + * That fails to create a UBI block device, so add it here. + */ + bootargs-append = " root=/dev/ubiblock0_1"; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&tlmm 52 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + led_spi { + compatible = "spi-gpio"; + #address-cells = <1>; + #size-cells = <0>; + + sck-gpios = <&tlmm 18 GPIO_ACTIVE_HIGH>; + mosi-gpios = <&tlmm 19 GPIO_ACTIVE_HIGH>; + + led_gpio: led_gpio@0 { + compatible = "fairchild,74hc595"; + reg = <0>; + gpio-controller; + #gpio-cells = <2>; + registers-number = <1>; + enable-gpios = <&tlmm 20 GPIO_ACTIVE_HIGH>; + spi-max-frequency = <1000000>; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_system_red: system-red { + label = "system:red"; + gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>; + }; + + led_system_green: system-green { + label = "system:green"; + gpios = <&tlmm 55 GPIO_ACTIVE_HIGH>; + }; + + led_system_blue: system-blue { + label = "system:blue"; + gpios = <&tlmm 56 GPIO_ACTIVE_HIGH>; + }; + + led_lan_g { + label = "lan:green"; + gpios = <&led_gpio 0 GPIO_ACTIVE_HIGH>; + }; + + led_lan_o { + label = "lan:orange"; + gpios = <&led_gpio 1 GPIO_ACTIVE_HIGH>; + }; + + led_2g_b { + label = "wlan2g:blue"; + gpios = <&led_gpio 2 GPIO_ACTIVE_HIGH>; + }; + + led_2g_g { + label = "wlan2g:green"; + gpios = <&led_gpio 3 GPIO_ACTIVE_HIGH>; + }; + + led_5g_b { + label = "wlan5g:blue"; + gpios = <&led_gpio 4 GPIO_ACTIVE_HIGH>; + }; + + led_5g_g { + label = "wlan5g:green"; + gpios = <&led_gpio 5 GPIO_ACTIVE_HIGH>; + }; + + }; +}; + +&edma { + status = "okay"; +}; + +&switch { + status = "okay"; + + switch_cpu_bmp = <0x01>; + switch_lan_bmp = <0x3e>; + switch_wan_bmp = <0x40>; + switch_mac_mode = <0x00>; + switch_mac_mode1 = <0xff>; + switch_mac_mode2 = <0x0f>; + bm_tick_mode = <0x00>; + tm_tick_mode = <0x00>; + + qcom,port_phyinfo { + port@5 { + port_id = <6>; + phy_address = <28>; + port_mac_sel = "QGMAC_PORT"; + }; + }; +}; + +&tlmm { + mdio_pins: mdio-pins { + mdc { + pins = "gpio68"; + function = "mdc"; + drive-strength = <8>; + bias-pull-up; + }; + + mdio { + pins = "gpio69"; + function = "mdio"; + drive-strength = <8>; + bias-pull-up; + }; + }; +}; + +&mdio { + status = "okay"; + + pinctrl-0 = <&mdio_pins>; + pinctrl-names = "default"; + reset-gpios = <&tlmm 44 GPIO_ACTIVE_LOW>; + + qca8081_28: ethernet-phy@28 { + reg = <28>; + }; +}; + +&dp6 { + status = "okay"; + phy-handle = <&qca8081_28>; + label = "lan"; +}; + +&qpic_bam { + status = "okay"; +}; + +&qpic_nand { + status = "okay"; + + nand@0 { + reg = <0>; + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + nand-bus-width = <8>; + + partitions { + compatible = "qcom,smem-part"; + }; + }; +}; + +&blsp1_uart5 { + status = "okay"; +}; + +&wifi { + status = "okay"; + + qcom,ath11k-calibration-variant = "Netgear-WAX620"; +}; diff --git a/target/linux/qualcommax/image/ipq807x.mk b/target/linux/qualcommax/image/ipq807x.mk index 440a267497..b61b721f3a 100644 --- a/target/linux/qualcommax/image/ipq807x.mk +++ b/target/linux/qualcommax/image/ipq807x.mk @@ -115,6 +115,20 @@ define Device/netgear_rax120v2 endef TARGET_DEVICES += netgear_rax120v2 +define Device/netgear_wax620 + $(call Device/FitImage) + $(call Device/UbiFit) + DEVICE_VENDOR := Netgear + DEVICE_MODEL := WAX620 + DEVICE_DTS_CONFIG := config@hk07 + BLOCKSIZE := 128k + PAGESIZE := 2048 + SOC := ipq8072 + DEVICE_PACKAGES += kmod-spi-gpio kmod-gpio-nxp-74hc164 \ + ipq-wifi-netgear_wax620 +endef +TARGET_DEVICES += netgear_wax620 + define Device/netgear_wax218 $(call Device/FitImage) $(call Device/UbiFit) diff --git a/target/linux/qualcommax/ipq807x/base-files/etc/board.d/01_leds b/target/linux/qualcommax/ipq807x/base-files/etc/board.d/01_leds index 6e2ec60403..913b58750c 100644 --- a/target/linux/qualcommax/ipq807x/base-files/etc/board.d/01_leds +++ b/target/linux/qualcommax/ipq807x/base-files/etc/board.d/01_leds @@ -12,6 +12,9 @@ edgecore,eap102) netgear,rax120v2) ucidef_set_led_netdev "aqr" "AQR" "white:aqr" "lan5" ;; +netgear,wax620) + ucidef_set_led_netdev "lan" "LAN" "lan:green" "lan" + ;; netgear,wax218) ucidef_set_led_netdev "lan" "LAN" "blue:lan" "lan" ucidef_set_led_wlan "wlan5g" "WIFI 5GHz" "blue:wlan5g" "phy0radio" diff --git a/target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network b/target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network index 3953ae8db2..ad8e34e9fe 100644 --- a/target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network +++ b/target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network @@ -25,7 +25,8 @@ ipq807x_setup_interfaces() netgear,rax120v2) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 lan5" "wan" ;; - netgear,wax218) + netgear,wax218|\ + netgear,wax620) ucidef_set_interface_lan "lan" "dhcp" ;; prpl,haze) diff --git a/target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata b/target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata index 742730f476..cba1f84b7f 100644 --- a/target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata +++ b/target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata @@ -16,6 +16,7 @@ case "$FIRMWARE" in dynalink,dl-wrx36|\ netgear,rax120v2|\ netgear,wax218|\ + netgear,wax620|\ qnap,301w|\ redmi,ax6|\ xiaomi,ax3600|\ diff --git a/target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh b/target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh index a7af1cc1df..90ebff17d4 100644 --- a/target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh +++ b/target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh @@ -69,7 +69,8 @@ platform_do_upgrade() { compex,wpq873|\ edimax,cax1800|\ netgear,rax120v2|\ - netgear,wax218) + netgear,wax218|\ + netgear,wax620) nand_do_upgrade "$1" ;; prpl,haze|\ -- 2.30.2