From 740d6ae5b982496fcea0666b2207cb34cc0e6015 Mon Sep 17 00:00:00 2001 From: John Rigby Date: Mon, 25 Jan 2010 23:12:57 -0700 Subject: [PATCH] fec_mxc: add MX25 support Use RMII for MX25 Add code to init gasket that enables RMII Signed-off-by: John Rigby CC: Ben Warren --- drivers/net/fec_mxc.c | 31 +++++++++++++++++++++++++++++- drivers/net/fec_mxc.h | 32 +++++++++++++++++++++++++++++-- include/asm-arm/arch-mx25/clock.h | 1 + 3 files changed, 61 insertions(+), 3 deletions(-) diff --git a/drivers/net/fec_mxc.c b/drivers/net/fec_mxc.c index e027894cff..5af9cdba2a 100644 --- a/drivers/net/fec_mxc.c +++ b/drivers/net/fec_mxc.c @@ -367,6 +367,34 @@ static int fec_open(struct eth_device *edev) */ writel(readl(&fec->eth->ecntrl) | FEC_ECNTRL_ETHER_EN, &fec->eth->ecntrl); +#ifdef CONFIG_MX25 + udelay(100); + /* + * setup the MII gasket for RMII mode + */ + + /* disable the gasket */ + writew(0, &fec->eth->miigsk_enr); + + /* wait for the gasket to be disabled */ + while (readw(&fec->eth->miigsk_enr) & MIIGSK_ENR_READY) + udelay(2); + + /* configure gasket for RMII, 50 MHz, no loopback, and no echo */ + writew(MIIGSK_CFGR_IF_MODE_RMII, &fec->eth->miigsk_cfgr); + + /* re-enable the gasket */ + writew(MIIGSK_ENR_EN, &fec->eth->miigsk_enr); + + /* wait until MII gasket is ready */ + int max_loops = 10; + while ((readw(&fec->eth->miigsk_enr) & MIIGSK_ENR_READY) == 0) { + if (--max_loops <= 0) { + printf("WAIT for MII Gasket ready timed out\n"); + break; + } + } +#endif miiphy_wait_aneg(edev); miiphy_speed(edev->name, CONFIG_FEC_MXC_PHYADDR); @@ -513,7 +541,8 @@ static void fec_halt(struct eth_device *dev) * Disable the Ethernet Controller * Note: this will also reset the BD index counter! */ - writel(readl(&fec->eth->ecntrl) & ~FEC_ECNTRL_ETHER_EN, &fec->eth->ecntrl); + writel(readl(&fec->eth->ecntrl) & ~FEC_ECNTRL_ETHER_EN, + &fec->eth->ecntrl); fec->rbd_index = 0; fec->tbd_index = 0; debug("eth_halt: done\n"); diff --git a/drivers/net/fec_mxc.h b/drivers/net/fec_mxc.h index 6cb1bfc055..5d0d69d5e9 100644 --- a/drivers/net/fec_mxc.h +++ b/drivers/net/fec_mxc.h @@ -145,9 +145,17 @@ struct ethernet_regs { uint32_t r_fdxfc; /* MBAR_ETH + 0x2DC */ uint32_t ieee_r_octets_ok; /* MBAR_ETH + 0x2E0 */ - uint32_t res14[6]; /* MBAR_ETH + 0x2E4-2FC */ - + uint32_t res14[7]; /* MBAR_ETH + 0x2E4-2FC */ + +#ifdef CONFIG_MX25 + uint16_t miigsk_cfgr; /* MBAR_ETH + 0x300 */ + uint16_t res15[3]; /* MBAR_ETH + 0x302-306 */ + uint16_t miigsk_enr; /* MBAR_ETH + 0x308 */ + uint16_t res16[3]; /* MBAR_ETH + 0x30a-30e */ + uint32_t res17[60]; /* MBAR_ETH + 0x300-3FF */ +#else uint32_t res15[64]; /* MBAR_ETH + 0x300-3FF */ +#endif }; #define FEC_IEVENT_HBERR 0x80000000 @@ -196,6 +204,26 @@ struct ethernet_regs { #define FEC_ECNTRL_RESET 0x00000001 /* reset the FEC */ #define FEC_ECNTRL_ETHER_EN 0x00000002 /* enable the FEC */ +#ifdef CONFIG_MX25 +/* defines for MIIGSK */ +/* RMII frequency control: 0=50MHz, 1=5MHz */ +#define MIIGSK_CFGR_FRCONT (1 << 6) +/* loopback mode */ +#define MIIGSK_CFGR_LBMODE (1 << 4) +/* echo mode */ +#define MIIGSK_CFGR_EMODE (1 << 3) +/* MII gasket mode field */ +#define MIIGSK_CFGR_IF_MODE_MASK (3 << 0) +/* MMI/7-Wire mode */ +#define MIIGSK_CFGR_IF_MODE_MII (0 << 0) +/* RMII mode */ +#define MIIGSK_CFGR_IF_MODE_RMII (1 << 0) +/* reflects MIIGSK Enable bit (RO) */ +#define MIIGSK_ENR_READY (1 << 2) +/* enable MIGSK (set by default) */ +#define MIIGSK_ENR_EN (1 << 1) +#endif + /** * @brief Descriptor buffer alignment * diff --git a/include/asm-arm/arch-mx25/clock.h b/include/asm-arm/arch-mx25/clock.h index b0752e7746..c59f588570 100644 --- a/include/asm-arm/arch-mx25/clock.h +++ b/include/asm-arm/arch-mx25/clock.h @@ -30,6 +30,7 @@ ulong imx_get_perclk(int clk); ulong imx_get_ahbclk(void); #define imx_get_uartclk() imx_get_perclk(15) +#define imx_get_fecclk() (imx_get_ahbclk()/2) #endif /* __ASM_ARCH_CLOCK_H */ -- 2.30.2