From 6fa4fbbc5293886aa6bae6e0cac4b99a4c472fc4 Mon Sep 17 00:00:00 2001 From: Tianling Shen Date: Wed, 1 Nov 2023 14:44:50 +0800 Subject: [PATCH] uboot-mediatek: add support for JDCloud RE-CP-03 The vendor U-Boot has enabled signature verification, so add a custom U-Boot build for OpenWrt. Signed-off-by: Tianling Shen --- package/boot/uboot-mediatek/Makefile | 13 + .../patches/440-add-jdcloud_re-cp-03.patch | 324 ++++++++++++++++++ 2 files changed, 337 insertions(+) create mode 100644 package/boot/uboot-mediatek/patches/440-add-jdcloud_re-cp-03.patch diff --git a/package/boot/uboot-mediatek/Makefile b/package/boot/uboot-mediatek/Makefile index 37fb68be22..8c0419f90c 100644 --- a/package/boot/uboot-mediatek/Makefile +++ b/package/boot/uboot-mediatek/Makefile @@ -419,6 +419,18 @@ define U-Boot/mt7986_glinet_gl-mt6000 DEPENDS:=+trusted-firmware-a-mt7986-emmc-ddr4 endef +define U-Boot/mt7986_jdcloud_re-cp-03 + NAME:=JDCloud RE-CP-03 + BUILD_SUBTARGET:=filogic + BUILD_DEVICES:=jdcloud_re-cp-03 + UBOOT_CONFIG:=mt7986a_jdcloud_re-cp-03 + UBOOT_IMAGE:=u-boot.fip + BL2_BOOTDEV:=emmc + BL2_SOC:=mt7986 + BL2_DDRTYPE:=ddr4 + DEPENDS:=+trusted-firmware-a-mt7986-emmc-ddr4 +endef + define U-Boot/mt7986_tplink_tl-xdr4288 NAME:=TP-LINK TL-XDR4288 BUILD_SUBTARGET:=filogic @@ -575,6 +587,7 @@ UBOOT_TARGETS := \ mt7986_bananapi_bpi-r3-snand \ mt7986_bananapi_bpi-r3-nor \ mt7986_glinet_gl-mt6000 \ + mt7986_jdcloud_re-cp-03 \ mt7986_tplink_tl-xdr4288 \ mt7986_tplink_tl-xdr6086 \ mt7986_tplink_tl-xdr6088 \ diff --git a/package/boot/uboot-mediatek/patches/440-add-jdcloud_re-cp-03.patch b/package/boot/uboot-mediatek/patches/440-add-jdcloud_re-cp-03.patch new file mode 100644 index 0000000000..e0f3a6e235 --- /dev/null +++ b/package/boot/uboot-mediatek/patches/440-add-jdcloud_re-cp-03.patch @@ -0,0 +1,324 @@ +--- /dev/null ++++ b/configs/mt7986a_jdcloud_re-cp-03_defconfig +@@ -0,0 +1,112 @@ ++CONFIG_ARM=y ++CONFIG_SYS_HAS_NONCACHED_MEMORY=y ++CONFIG_POSITION_INDEPENDENT=y ++CONFIG_ARCH_MEDIATEK=y ++CONFIG_TEXT_BASE=0x41e00000 ++CONFIG_SYS_MALLOC_F_LEN=0x4000 ++CONFIG_NR_DRAM_BANKS=1 ++CONFIG_ENV_SIZE=0x40000 ++CONFIG_ENV_OFFSET=0x400000 ++CONFIG_DEFAULT_DEVICE_TREE="mt7986a-jdcloud_re-cp-03" ++CONFIG_SYS_PROMPT="MT7986> " ++CONFIG_OF_LIBFDT_OVERLAY=y ++CONFIG_TARGET_MT7986=y ++CONFIG_PRE_CON_BUF_ADDR=0x4007EF00 ++CONFIG_DEBUG_UART_BASE=0x11002000 ++CONFIG_DEBUG_UART_CLOCK=40000000 ++CONFIG_ENV_OFFSET_REDUND=0x440000 ++CONFIG_SYS_LOAD_ADDR=0x46000000 ++CONFIG_DEBUG_UART=y ++CONFIG_FIT=y ++CONFIG_BOOTDELAY=30 ++CONFIG_AUTOBOOT_KEYED=y ++CONFIG_AUTOBOOT_MENU_SHOW=y ++CONFIG_DEFAULT_FDT_FILE="mediatek/mt7986a-jdcloud_re-cp-03.dtb" ++CONFIG_LOGLEVEL=7 ++CONFIG_PRE_CONSOLE_BUFFER=y ++CONFIG_LOG=y ++CONFIG_BOARD_LATE_INIT=y ++CONFIG_HUSH_PARSER=y ++CONFIG_CMD_CPU=y ++CONFIG_CMD_LICENSE=y ++CONFIG_CMD_BOOTMENU=y ++CONFIG_CMD_ASKENV=y ++CONFIG_CMD_ERASEENV=y ++CONFIG_CMD_ENV_FLAGS=y ++CONFIG_CMD_STRINGS=y ++CONFIG_CMD_DM=y ++CONFIG_CMD_GPIO=y ++CONFIG_CMD_PWM=y ++CONFIG_CMD_GPT=y ++CONFIG_CMD_MMC=y ++CONFIG_CMD_PART=y ++CONFIG_CMD_DHCP=y ++CONFIG_CMD_TFTPSRV=y ++CONFIG_CMD_RARP=y ++CONFIG_CMD_PING=y ++CONFIG_CMD_CDP=y ++CONFIG_CMD_SNTP=y ++CONFIG_CMD_DNS=y ++CONFIG_CMD_LINK_LOCAL=y ++CONFIG_CMD_PXE=y ++CONFIG_CMD_CACHE=y ++CONFIG_CMD_PSTORE=y ++CONFIG_CMD_PSTORE_MEM_ADDR=0x42ff0000 ++CONFIG_CMD_UUID=y ++CONFIG_CMD_HASH=y ++CONFIG_CMD_SMC=y ++CONFIG_CMD_EXT4=y ++CONFIG_CMD_FAT=y ++CONFIG_CMD_FS_GENERIC=y ++CONFIG_CMD_FS_UUID=y ++CONFIG_OF_EMBED=y ++CONFIG_ENV_OVERWRITE=y ++CONFIG_ENV_IS_IN_MMC=y ++CONFIG_SYS_REDUNDAND_ENVIRONMENT=y ++CONFIG_SYS_RELOC_GD_ENV_ADDR=y ++CONFIG_USE_DEFAULT_ENV_FILE=y ++CONFIG_DEFAULT_ENV_FILE="jdcloud_re-cp-03_env" ++CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y ++CONFIG_VERSION_VARIABLE=y ++CONFIG_NET_RANDOM_ETHADDR=y ++CONFIG_NETCONSOLE=y ++CONFIG_USE_IPADDR=y ++CONFIG_IPADDR="192.168.1.1" ++CONFIG_USE_SERVERIP=y ++CONFIG_SERVERIP="192.168.1.254" ++CONFIG_REGMAP=y ++CONFIG_SYSCON=y ++CONFIG_BUTTON=y ++CONFIG_BUTTON_GPIO=y ++CONFIG_CLK=y ++CONFIG_GPIO_HOG=y ++CONFIG_LED=y ++CONFIG_LED_BLINK=y ++CONFIG_LED_GPIO=y ++CONFIG_SUPPORT_EMMC_BOOT=y ++CONFIG_MMC_HS200_SUPPORT=y ++CONFIG_MMC_MTK=y ++CONFIG_PHY_FIXED=y ++CONFIG_DM_MDIO=y ++CONFIG_MEDIATEK_ETH=y ++CONFIG_PHY=y ++CONFIG_PHY_MTK_TPHY=y ++CONFIG_PINCTRL=y ++CONFIG_PINCONF=y ++CONFIG_PINCTRL_MT7622=y ++CONFIG_PINCTRL_MT7986=y ++CONFIG_POWER_DOMAIN=y ++CONFIG_MTK_POWER_DOMAIN=y ++CONFIG_DM_REGULATOR=y ++CONFIG_DM_REGULATOR_FIXED=y ++CONFIG_DM_REGULATOR_GPIO=y ++CONFIG_DM_PWM=y ++CONFIG_PWM_MTK=y ++CONFIG_RAM=y ++CONFIG_SCSI=y ++CONFIG_DM_SCSI=y ++CONFIG_DM_SERIAL=y ++CONFIG_MTK_SERIAL=y ++CONFIG_ZSTD=y ++CONFIG_HEXDUMP=y ++CONFIG_LMB_MAX_REGIONS=64 +--- /dev/null ++++ b/arch/arm/dts/mt7986a-jdcloud_re-cp-03.dts +@@ -0,0 +1,148 @@ ++// SPDX-License-Identifier: GPL-2.0-or-later ++ ++/dts-v1/; ++#include ++#include "mt7986.dtsi" ++#include ++ ++/ { ++ #address-cells = <1>; ++ #size-cells = <1>; ++ model = "JDCloud RE-CP-03"; ++ compatible = "mediatek,mt7986", "mediatek,mt7986-rfb"; ++ ++ chosen { ++ stdout-path = &uart0; ++ tick-timer = &timer0; ++ }; ++ ++ memory@40000000 { ++ device_type = "memory"; ++ reg = <0x40000000 0x40000000>; ++ }; ++ ++ gpio-keys { ++ compatible = "gpio-keys"; ++ ++ button-joylink { ++ label = "joylink"; ++ linux,code = ; ++ gpios = <&gpio 10 GPIO_ACTIVE_LOW>; ++ }; ++ ++ button-reset { ++ label = "reset"; ++ linux,code = ; ++ gpios = <&gpio 9 GPIO_ACTIVE_LOW>; ++ }; ++ }; ++ ++ gpio-leds { ++ compatible = "gpio-leds"; ++ ++ led-0 { ++ label = "blue:status"; ++ gpios = <&gpio 7 GPIO_ACTIVE_HIGH>; ++ default-state = "off"; ++ }; ++ ++ led-1 { ++ label = "red:status"; ++ gpios = <&gpio 11 GPIO_ACTIVE_HIGH>; ++ default-state = "on"; ++ }; ++ ++ led-2 { ++ label = "green:status"; ++ gpios = <&gpio 12 GPIO_ACTIVE_LOW>; ++ default-state = "off"; ++ }; ++ }; ++ ++ reg_1p8v: regulator-1p8v { ++ compatible = "regulator-fixed"; ++ regulator-name = "fixed-1.8V"; ++ regulator-min-microvolt = <1800000>; ++ regulator-max-microvolt = <1800000>; ++ regulator-boot-on; ++ regulator-always-on; ++ }; ++ ++ reg_3p3v: regulator-3p3v { ++ compatible = "regulator-fixed"; ++ regulator-name = "fixed-3.3V"; ++ regulator-min-microvolt = <3300000>; ++ regulator-max-microvolt = <3300000>; ++ regulator-boot-on; ++ regulator-always-on; ++ }; ++}; ++ ++ð { ++ status = "okay"; ++ mediatek,gmac-id = <0>; ++ phy-mode = "2500base-x"; ++ mediatek,switch = "mt7531"; ++ reset-gpios = <&gpio 5 GPIO_ACTIVE_HIGH>; ++ ++ fixed-link { ++ speed = <2500>; ++ full-duplex; ++ }; ++}; ++ ++&mmc0 { ++ bus-width = <8>; ++ cap-mmc-highspeed; ++ cap-mmc-hw-reset; ++ max-frequency = <200000000>; ++ non-removable; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&mmc0_pins_default>; ++ vmmc-supply = <®_3p3v>; ++ vqmmc-supply = <®_1p8v>; ++ status = "okay"; ++}; ++ ++&pinctrl { ++ mmc0_pins_default: mmc0default { ++ mux { ++ function = "flash"; ++ groups = "emmc_51"; ++ }; ++ ++ conf-cmd-dat { ++ pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2", ++ "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5", ++ "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD"; ++ input-enable; ++ drive-strength = ; ++ bias-pull-up = ; ++ }; ++ ++ conf-clk { ++ pins = "EMMC_CK"; ++ drive-strength = ; ++ bias-pull-down = ; ++ }; ++ ++ conf-dsl { ++ pins = "EMMC_DSL"; ++ bias-pull-down = ; ++ }; ++ ++ conf-rst { ++ pins = "EMMC_RSTB"; ++ drive-strength = ; ++ bias-pull-up = ; ++ }; ++ }; ++}; ++ ++&uart0 { ++ status = "okay"; ++}; ++ ++&watchdog { ++ status = "disabled"; ++}; +--- /dev/null ++++ b/jdcloud_re-cp-03_env +@@ -0,0 +1,55 @@ ++ipaddr=192.168.1.1 ++serverip=192.168.1.254 ++loadaddr=0x46000000 ++console=earlycon=uart8250,mmio32,0x11002000 console=ttyS0 ++bootargs=root=/dev/mmcblk0p65 ++bootcmd=if pstore check ; then run boot_recovery ; else run boot_emmc ; fi ++bootconf=config-1 ++bootdelay=0 ++bootfile=openwrt-mediatek-filogic-jdcloud_re-cp-03-initramfs-recovery.itb ++bootfile_bl2=openwrt-mediatek-filogic-jdcloud_re-cp-03-preloader.bin ++bootfile_fip=openwrt-mediatek-filogic-jdcloud_re-cp-03-bl31-uboot.fip ++bootfile_upg=openwrt-mediatek-filogic-jdcloud_re-cp-03-squashfs-sysupgrade.itb ++bootled_pwr=red:status ++bootled_rec=blue:status ++bootmenu_confirm_return=askenv - Press ENTER to return to menu ; bootmenu 60 ++bootmenu_default=0 ++bootmenu_delay=0 ++bootmenu_title= ( ( ( OpenWrt ) ) ) ++bootmenu_0=Initialize environment.=run _firstboot ++bootmenu_0d=Run default boot command.=run boot_default ++bootmenu_1=Boot system via TFTP.=run boot_tftp ; run bootmenu_confirm_return ++bootmenu_2=Boot production system from eMMC.=run boot_production ; run bootmenu_confirm_return ++bootmenu_3=Boot recovery system from eMMC.=run boot_recovery ; run bootmenu_confirm_return ++bootmenu_4=Load production system via TFTP then write to eMMC.=setenv noboot 1 ; setenv replacevol 1 ; run boot_tftp_production ; setenv noboot ; setenv replacevol ; run bootmenu_confirm_return ++bootmenu_5=Load recovery system via TFTP then write to eMMC.=setenv noboot 1 ; setenv replacevol 1 ; run boot_tftp_recovery ; setenv noboot ; setenv replacevol ; run bootmenu_confirm_return ++bootmenu_6=Load BL31+U-Boot FIP via TFTP then write to eMMC.=run boot_tftp_write_fip ; run bootmenu_confirm_return ++bootmenu_7=Load BL2 preloader via TFTP then write to eMMC.=run boot_tftp_write_bl2 ; run bootmenu_confirm_return ++bootmenu_8=Reboot.=reset ++bootmenu_9=Reset all settings to factory defaults.=run reset_factory ; reset ++boot_first=if button reset ; then led $bootled_rec on ; run boot_tftp_recovery ; setenv flag_recover 1 ; run boot_default ; fi ; bootmenu ++boot_default=if env exists flag_recover ; then else run bootcmd ; fi ; run boot_recovery ; setenv replacevol 1 ; run boot_tftp_forever ++boot_production=led $bootled_pwr on ; run emmc_read_production && bootm $loadaddr#$bootconf ; led $bootled_pwr off ++boot_recovery=led $bootled_rec on ; run emmc_read_recovery && bootm $loadaddr#$bootconf ; led $bootled_rec off ++boot_emmc=run boot_production ; run boot_recovery ++boot_tftp_forever=led $bootled_rec on ; while true ; do run boot_tftp_recovery ; sleep 1 ; done ++boot_tftp_production=tftpboot $loadaddr $bootfile_upg && env exists replacevol && iminfo $loadaddr && run emmc_write_production ; if env exists noboot ; then else bootm $loadaddr#$bootconf ; fi ++boot_tftp_recovery=tftpboot $loadaddr $bootfile && env exists replacevol && iminfo $loadaddr && run emmc_write_recovery ; if env exists noboot ; then else bootm $loadaddr#$bootconf ; fi ++boot_tftp_write_fip=tftpboot $loadaddr $bootfile_fip && run emmc_write_fip ++boot_tftp_write_bl2=tftpboot $loadaddr $bootfile_bl2 && run emmc_write_bl2 ++boot_tftp=tftpboot $loadaddr $bootfile && bootm $loadaddr#$bootconf ++mmc_write_vol=imszb $loadaddr image_size && test 0x$image_size -le 0x$part_size && mmc erase 0x$part_addr 0x$image_size && mmc write $loadaddr 0x$part_addr 0x$image_size ++mmc_read_vol=mmc read $loadaddr $part_addr 0x100 && imszb $loadaddr image_size && test 0x$image_size -le 0x$part_size && mmc read $loadaddr 0x$part_addr 0x$image_size && setexpr filesize $image_size * 0x200 ++part_default=production ++part_recovery=recovery ++reset_factory=eraseenv && reset ++emmc_read_production=part start mmc 0 $part_default part_addr && part size mmc 0 $part_default part_size && run mmc_read_vol ++emmc_read_recovery=part start mmc 0 $part_recovery part_addr && part size mmc 0 $part_recovery part_size && run mmc_read_vol ++emmc_write_bl2=mmc partconf 0 1 1 1 && mmc erase 0x0 0x400 && mmc write $fileaddr 0x0 0x400 ; mmc partconf 0 1 1 0 ++emmc_write_fip=mmc erase 0x3400 0x2000 && mmc write $fileaddr 0x3400 0x2000 && mmc erase 0x2000 0x800 ++emmc_write_production=part start mmc 0 $part_default part_addr && part size mmc 0 $part_default part_size && run mmc_write_vol ++emmc_write_recovery=part start mmc 0 $part_recovery part_addr && part size mmc 0 $part_recovery part_size && run mmc_write_vol ++_init_env=setenv _init_env ; setenv _create_env ; saveenv ; saveenv ++_firstboot=setenv _firstboot ; run _switch_to_menu ; run _init_env ; run boot_first ++_switch_to_menu=setenv _switch_to_menu ; setenv bootdelay 3 ; setenv bootmenu_delay 3 ; setenv bootmenu_0 $bootmenu_0d ; setenv bootmenu_0d ; run _bootmenu_update_title ++_bootmenu_update_title=setenv _bootmenu_update_title ; setenv bootmenu_title "$bootmenu_title $ver" -- 2.30.2