From 6c85a449a988876fdfd4ce84d6aa5ffe4a2820c1 Mon Sep 17 00:00:00 2001 From: Leon Maurice Adam Date: Sun, 3 May 2020 12:44:24 +0200 Subject: [PATCH] lantiq: add support for AVM FRITZ!Box 7430 Hardware: - SoC: Lantiq VRX 220 - CPU: 2x MIPS 34Kc 500 MHz - RAM: 128 MiB 250 MHz - Flash: 128 MiB NAND - Ethernet: Built-in Fast Ethernet switch, 4 ports used - Wifi: Atheros AR9381-AL1A b/g/n with 2 pcb/internal and 1 external antennas - USB: 1x USB 2.0 - DSL: Built-in A/VDSL2 modem - DECT: Dialog SC14441 - LEDs: 1 two-color, 4 one-color - Buttons: 1x DECT, 1x WIFI - Telephone connectors: 1 FXS port via TAE or RJ11 connector With the exception of FXS/DECT everything works (there are no drivers for AVM's FXS or DECT implementation), DSL is yet untested. Installation: Boot up the device and wait a few seconds. Run the eva_ramboot.py script in scripts/flashing/ to load the initramfs image on the device: $ ./scripts/flashing/eva_ramboot.py 192.168.178.1 If the script fails to reach the device, maybe try 169.254.120.1. Wait until booting is complete. You should now be able to reach your device under the default ip address 192.168.1.1. Before flashing, check if linux_fs_start is not set to 1 in the tffs partition: $ fritz_tffs_nand -d /dev/mtd1 -n linux_fs_start If linux_fs_start is 1, you will need to reset it to 0, either by FTP, upgrading FritzOS or doing a recovery. Now you should be able to flash the device using sysupgrade. Signed-off-by: Leon Maurice Adam Acked-by: Aleksander Jan Bajkowski [drop BOARD_NAME, use wpad-basic-wolfssl, drop 4.19, drop dts-v1, remove model prefix from LED names] Signed-off-by: Adrian Schmutzler --- .../boot/dts/lantiq/vr9_avm_fritz7430.dts | 273 ++++++++++++++++++ target/linux/lantiq/image/vr9.mk | 10 + .../xrx200/base-files/etc/board.d/02_network | 10 +- .../etc/hotplug.d/firmware/12-ath9k-eeprom | 3 +- .../xrx200/base-files/lib/upgrade/platform.sh | 1 + 5 files changed, 294 insertions(+), 3 deletions(-) create mode 100644 target/linux/lantiq/files/arch/mips/boot/dts/lantiq/vr9_avm_fritz7430.dts diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/lantiq/vr9_avm_fritz7430.dts b/target/linux/lantiq/files/arch/mips/boot/dts/lantiq/vr9_avm_fritz7430.dts new file mode 100644 index 000000000000..3894fecb434b --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/lantiq/vr9_avm_fritz7430.dts @@ -0,0 +1,273 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "vr9.dtsi" + +#include +#include + +/ { + compatible = "avm,fritz7430", "lantiq,xway", "lantiq,vr9"; + model = "AVM FRITZ!Box 7430"; + + chosen { + bootargs = "console=ttyLTQ0,115200"; + }; + + aliases { + led-boot = &led_power; + led-failsafe = &led_info_red; + led-running = &led_power; + led-upgrade = &led_info_green; + + led-dsl = &led_info_green; + led-wifi = &led_wifi; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x8000000>; + }; + + keys { + compatible = "gpio-keys-polled"; + poll-interval = <100>; + + dect { + label = "dect"; + gpios = <&gpio 1 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + wifi { + label = "wifi"; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_power: power { + label = "green:power"; + gpios = <&gpio 31 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + + led_info_green: info_green { + label = "green:info"; + gpios = <&gpio 0 GPIO_ACTIVE_LOW>; + }; + + led_info_red: info_red { + label = "red:info"; + gpios = <&gpio 15 GPIO_ACTIVE_LOW>; + }; + + led_wifi: wifi { + label = "green:wifi"; + gpios = <&gpio 34 GPIO_ACTIVE_LOW>; + }; + + dect { + label = "green:dect"; + gpios = <&gpio 35 GPIO_ACTIVE_LOW>; + }; + + fon { + label = "green:fon"; + gpios = <&gpio 36 GPIO_ACTIVE_LOW>; + }; + }; + + usb0_vbus: regulator-usb0-vbus { + compatible = "regulator-fixed"; + + regulator-name = "USB0_VBUS"; + + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + gpio = <&gpio 5 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +&localbus { + flash@0 { + compatible = "lantiq,nand-xway"; + bank-width = <2>; + reg = <0 0x0 0x8000000>; + lantiq,cs = <1>; + + pinctrl-0 = <&nand_pins>, <&nand_cs1_pins>; + pinctrl-names = "default"; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "urlader"; + reg = <0x0 0x40000>; + read-only; + }; + + partition@40000 { + label = "nand-tffs"; + reg = <0x40000 0x400000>; + read-only; + }; + + partition@440000 { + label = "kernel"; + reg = <0x440000 0x400000>; + }; + + partition@840000 { + label = "ubi"; + reg = <0x840000 0x3000000>; + }; + + partition@3840000 { + label = "reserved-kernel"; + reg = <0x3840000 0x400000>; + read-only; + }; + + partition@3c40000 { + label = "reserved-filesystem"; + reg = <0x3c40000 0x3000000>; + read-only; + }; + + partition@6c40000 { + label = "config"; + reg = <0x6c40000 0x200000>; + read-only; + }; + + partition@6e40000 { + label = "nand-filesystem"; + reg = <0x6e40000 0x11c0000>; + read-only; + }; + }; + }; +}; + +&pcie0 { + status = "okay"; + + gpio-reset = <&gpio 11 GPIO_ACTIVE_LOW>; + + pcie@0 { + reg = <0 0 0 0 0>; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + device_type = "pci"; + + wifi@168c,abcd { + compatible = "pci168c,abcd"; + reg = <0 0 0 0 0>; + qca,no-eeprom; /* load from ath9k-eeprom-pci-0000:01:00.0.bin */ + }; + }; +}; + +&gphy0 { + lantiq,gphy-mode = ; +}; + +&gphy1 { + lantiq,gphy-mode = ; +}; + +ð0 { + interface@0 { + compatible = "lantiq,xrx200-pdi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + lantiq,switch; + + ethernet@2 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <2>; + phy-mode = "mii"; + phy-handle = <&phy11>; + }; + + ethernet@3 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <3>; + phy-mode = "mii"; + phy-handle = <&phy12>; + }; + + ethernet@4 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <4>; + phy-mode = "mii"; + phy-handle = <&phy13>; + }; + + ethernet@5 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <5>; + phy-mode = "mii"; + phy-handle = <&phy14>; + }; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + compatible = "lantiq,xrx200-mdio"; + + phy11: ethernet-phy@11 { + reg = <0x11>; + compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22"; + }; + + phy12: ethernet-phy@12 { + reg = <0x12>; + compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22"; + }; + + phy13: ethernet-phy@13 { + reg = <0x13>; + compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22"; + }; + + phy14: ethernet-phy@14 { + reg = <0x14>; + compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22"; + }; + }; +}; + +&gpio { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + pcie-rst { + lantiq,pins = "io11"; + lantiq,open-drain = <1>; + lantiq,output = <1>; + }; + }; +}; + +&usb_phy0 { + status = "okay"; +}; + +&usb0 { + status = "okay"; + + vbus-supply = <&usb0_vbus>; +}; diff --git a/target/linux/lantiq/image/vr9.mk b/target/linux/lantiq/image/vr9.mk index e5ebbd3b65bc..d3420bb2b9d6 100644 --- a/target/linux/lantiq/image/vr9.mk +++ b/target/linux/lantiq/image/vr9.mk @@ -157,6 +157,16 @@ define Device/avm_fritz7412 endef TARGET_DEVICES += avm_fritz7412 +define Device/avm_fritz7430 + $(Device/AVM) + $(Device/NAND) + DEVICE_MODEL := FRITZ!Box 7430 + KERNEL_SIZE := 4096k + IMAGE_SIZE := 49152k + DEVICE_PACKAGES := kmod-ath9k kmod-owl-loader wpad-basic-wolfssl fritz-tffs-nand fritz-caldata +endef +TARGET_DEVICES += avm_fritz7430 + define Device/bt_homehub-v5a $(Device/NAND) DEVICE_VENDOR := British Telecom diff --git a/target/linux/lantiq/xrx200/base-files/etc/board.d/02_network b/target/linux/lantiq/xrx200/base-files/etc/board.d/02_network index 07bcdf9f8455..f7af17995f02 100755 --- a/target/linux/lantiq/xrx200/base-files/etc/board.d/02_network +++ b/target/linux/lantiq/xrx200/base-files/etc/board.d/02_network @@ -44,6 +44,10 @@ lantiq_setup_interfaces() ucidef_add_switch "switch0" \ "0:lan:3" "1:lan:4" "2:lan:2" "4:lan:1" "6t@eth0" ;; + avm,fritz7430) + ucidef_add_switch "switch0" \ + "2:lan:3" "3:lan:4" "4:lan:1" "5:lan:2" "6t@eth0" + ;; bt,homehub-v5a) ucidef_add_switch "switch0" \ "0:lan:3" "1:lan:4" "2:lan:2" "4:lan:1" "5:wan:5" "6t@eth0" @@ -85,7 +89,8 @@ lantiq_setup_dsl() avm,fritz3370-rev2-micron|\ avm,fritz7360sl|\ avm,fritz7362sl|\ - avm,fritz7412) + avm,fritz7412|\ + avm,fritz7430) annex="b" ;; esac @@ -135,7 +140,8 @@ lantiq_setup_macs() lan_mac=$(fritz_tffs -n maca -i $(find_mtd_part "tffs (1)")) wan_mac=$(fritz_tffs -n macdsl -i $(find_mtd_part "tffs (1)")) ;; - avm,fritz7412) + avm,fritz7412|\ + avm,fritz7430) tffsdev=$(find_mtd_chardev "nand-tffs") lan_mac=$(/usr/bin/fritz_tffs_nand -d $tffsdev -n maca -o) wan_mac=$(/usr/bin/fritz_tffs_nand -d $tffsdev -n macdsl -o) diff --git a/target/linux/lantiq/xrx200/base-files/etc/hotplug.d/firmware/12-ath9k-eeprom b/target/linux/lantiq/xrx200/base-files/etc/hotplug.d/firmware/12-ath9k-eeprom index 75cc50a207b7..ee8cc3879a59 100644 --- a/target/linux/lantiq/xrx200/base-files/etc/hotplug.d/firmware/12-ath9k-eeprom +++ b/target/linux/lantiq/xrx200/base-files/etc/hotplug.d/firmware/12-ath9k-eeprom @@ -20,7 +20,8 @@ case "$FIRMWARE" in avm,fritz7360-v2) caldata_extract "urlader" 0x985 0x1000 ;; - avm,fritz7412) + avm,fritz7412|\ + avm,fritz7430) /usr/bin/fritz_cal_extract -i 1 -s 0x1e000 -e 0x207 -l 4096 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader") ;; bt,homehub-v5a) diff --git a/target/linux/lantiq/xrx200/base-files/lib/upgrade/platform.sh b/target/linux/lantiq/xrx200/base-files/lib/upgrade/platform.sh index dcd797c30dc9..07700524882f 100755 --- a/target/linux/lantiq/xrx200/base-files/lib/upgrade/platform.sh +++ b/target/linux/lantiq/xrx200/base-files/lib/upgrade/platform.sh @@ -13,6 +13,7 @@ platform_do_upgrade() { avm,fritz3370-rev2-micron|\ avm,fritz7362sl|\ avm,fritz7412|\ + avm,fritz7430|\ bt,homehub-v5a|\ zyxel,p-2812hnu-f1|\ zyxel,p-2812hnu-f3) -- 2.30.2