From 6bec68062b83b86ed65a96fe4a7e1ed30e5423b9 Mon Sep 17 00:00:00 2001 From: Valerio 'ftp21' Mancini Date: Wed, 4 Oct 2023 11:43:25 +0200 Subject: [PATCH] mediatek: add Zyxel EX5601-T0 with uboot custom partition MIME-Version: 1.0 Content-Type: text/plain; charset=utf8 Content-Transfer-Encoding: 8bit The flash procedure is similar to the Xiaomi AX6000 router. Load openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-initramfs-recovery.itb from original Zyxel U-Boot: tftpboot openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-initramfs-recovery.itb bootm 0x46000000 Load mtd-rw insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1 Format ubi and create ubootenv partitions ubidetach -p /dev/mtd5; ubiformat /dev/mtd5 -y; ubiattach -p /dev/mtd5 ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB Copy openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-initramfs-recovery.itb to /tmp and create recovery partition. If your recovery image is larger than 10MiB, size the recovery partition accordingly to make it fit. ubimkvol /dev/ubi0 -n 2 -N recovery -s 10MiB ubiupdatevol /dev/ubi0_2 openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-initramfs-recovery.itb Copy preloader and uboot to /tmp and write them in the mtd mtd write /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-preloader.bin bl2 mtd write /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-bl31-uboot.fip fip Now write the firmware: sysupgrade -n /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-squashfs-sysupgrade.itb To create a correct BL2, I had to add a profile for 'spim:4k+256' as I could not find a way to value the variable 'NAND_TYPE'. Features and fixes from hitech95 tree has been squashed, I'm attaching his commit message: The Power LED was not working correctly and not reacting to the boot process and statuses. The board has space (footprint) for an unpopulated Zigbee chip, while we dont know the device model having this chip populated we have to assure that the common dts doesnt enable interfaces that share pins with such device. In this instance the PCIe and the uart1 and uart2 are disabled. Some of the control PCIE pins seems to be used for the Zigbee chip, UART1 seems to be used as a flash port while UART2 should be the main comunication interface of Zigbee chip. The Zigbee chip should be a EFR32MG21. But the pins used for UART seems to be not on standard PINS used by other adapters. So it cannot run firmwares shared on the web. But it should be possible to build a custom firmware with the corrtect pinmux. This commit also contains the following squashed commit from hitech95 - mediatek: fix sysupgrade for Zyxel EX7601-T0 ubootmod Changes and fixes added in common board: - added aliases for boot status leds. - added aliases for the mac-label-device. - added pin claims for core features (MDIO and UART 0) - added default LEDs configuration (01_leds) - added default network configuration (02_network) - added missing kmod-usb3 module for USB3 - fixed LED names - fixed reset pin for SLIC chip - removed unused pinmux configurations and devices - fix LAN (switch) port numbering - using nvmem cells for wifi eeprom, dropping deprecated "mediatek,mtd-eeprom" - proper factory partition and mac address handling - cleaned up spi_nand sections and partition Changes and fixxes added in stock layout: - added NMBM, if u-boot has it, the kernel must be informed. Co-authored-by: Nicolò Veronese Co-developed-by: Nicolò Veronese Signed-off-by: Nicolò Veronese Signed-off-by: Valerio 'ftp21' Mancini (cherry picked from commit b5df398a36f153f036c0a5ff9b221abb0f6f240a) --- .../dts/mt7986a-zyxel-ex5601-t0-common.dtsi | 433 +++++++++++++ .../dts/mt7986a-zyxel-ex5601-t0-stock.dts | 582 +++--------------- .../dts/mt7986a-zyxel-ex5601-t0-ubootmod.dts | 106 ++++ .../filogic/base-files/etc/board.d/01_leds | 7 + .../filogic/base-files/etc/board.d/02_network | 4 + .../etc/hotplug.d/ieee80211/11_fix_wifi_mac | 3 +- .../base-files/lib/upgrade/platform.sh | 5 + target/linux/mediatek/image/filogic.mk | 34 +- 8 files changed, 658 insertions(+), 516 deletions(-) create mode 100644 target/linux/mediatek/dts/mt7986a-zyxel-ex5601-t0-common.dtsi create mode 100644 target/linux/mediatek/dts/mt7986a-zyxel-ex5601-t0-ubootmod.dts diff --git a/target/linux/mediatek/dts/mt7986a-zyxel-ex5601-t0-common.dtsi b/target/linux/mediatek/dts/mt7986a-zyxel-ex5601-t0-common.dtsi new file mode 100644 index 0000000000..04e86a737d --- /dev/null +++ b/target/linux/mediatek/dts/mt7986a-zyxel-ex5601-t0-common.dtsi @@ -0,0 +1,433 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright (C) 2021 MediaTek Inc. + * Author: Sam.Shih + */ + +#include "mt7986a.dtsi" +#include +#include + +/ { + aliases { + serial0 = &uart0; + label-mac-device = &gmac0; + led-boot = &led_status_green; + led-failsafe = &led_status_red; + led-running = &led_status_green; + led-upgrade = &led_status_red; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory { + reg = <0 0x40000000 0 0x40000000>; + }; + + reg_1p8v: regulator-1p8v { + compatible = "regulator-fixed"; + regulator-name = "fixed-1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_3p3v: regulator-3p3v { + compatible = "regulator-fixed"; + regulator-name = "fixed-3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_5v: regulator-5v { + compatible = "regulator-fixed"; + regulator-name = "fixed-5V"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + regulator-always-on; + }; + + gpio-keys { + compatible = "gpio-keys"; + poll-interval = <20>; + + reset-button { + label = "reset"; + gpios = <&pio 21 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + wlan-button { + label = "wlan"; + gpios = <&pio 11 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + wps-button { + label = "wps"; + gpios = <&pio 56 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_green_wifi24g { + label = "green:wifi24g"; + gpios = <&pio 1 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led_green_wifi5g { + label = "green:wifi5g"; + gpios = <&pio 2 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led_green_inet { + label = "green:inet"; + gpios = <&pio 14 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led_red_inet { + label = "red:inet"; + gpios = <&pio 15 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led_status_green: led_green_pwr { + label = "green:pwr"; + gpios = <&pio 13 GPIO_ACTIVE_LOW>; + linux,default-trigger = "timer"; /* Default blinking */ + led-pattern = <125 125>; /* Fast blink is 4 HZ */ + }; + + led_status_red: led_red_pwr { + label = "red:pwr"; + gpios = <&pio 12 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led_green_fxs { + label = "green:fxs"; + gpios = <&pio 16 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led_amber_fxs { + label = "amber:fxs"; + gpios = <&pio 17 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led_amber_wps24g { + label = "amber:wps24g"; + gpios = <&pio 18 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led_amber_wps5g { + label = "amber:wps5g"; + gpios = <&pio 19 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led_green_lan { + label = "green:lan"; + gpios = <&pio 20 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led_green_sfp { + label = "green:sfp"; + gpios = <&pio 24 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + }; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi_flash_pins>; + cs-gpios = <0>, <0>; + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + spi_nand: spi_nand@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spi-nand"; + reg = <1>; + spi-max-frequency = <10000000>; + spi-tx-bus-width = <4>; + spi-rx-bus-width = <4>; + + nand_partitions: partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + }; + }; +}; + +ð { + pinctrl-names = "default"; + pinctrl-0 = <ð_pins>; + status = "okay"; + + gmac0: mac@0 { + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-mode = "2500base-x"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + + gmac1: mac@1 { + compatible = "mediatek,eth-mac"; + reg = <1>; + phy-mode = "2500base-x"; + phy = <&phy6>; + }; + + mdio: mdio-bus { + #address-cells = <1>; + #size-cells = <0>; + reset-gpios = <&pio 6 GPIO_ACTIVE_LOW>; + reset-delay-us = <1500000>; + reset-post-delay-us = <1000000>; + + phy5: phy@5 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <5>; + mxl,led-config = <0x03f0 0x0 0x0 0x0>; + }; + + phy6: phy@6 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <6>; + mxl,led-config = <0x00f0 0x0 0x0 0x0>; + }; + + switch@1f { + compatible = "mediatek,mt7531"; + reg = <31>; + reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + reg = <1>; + label = "lan2"; + }; + + port@2 { + reg = <2>; + label = "lan3"; + }; + + port@3 { + reg = <3>; + label = "lan4"; + }; + + port@5 { + reg = <5>; + label = "lan1"; + phy-mode = "2500base-x"; + phy = <&phy5>; + }; + + port@6 { + reg = <6>; + ethernet = <&gmac0>; + phy-mode = "2500base-x"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + }; + }; + }; +}; + +&watchdog { + status = "okay"; +}; + +&wifi { + status = "okay"; + pinctrl-names = "default", "dbdc"; + pinctrl-0 = <&wf_2g_5g_pins>; + pinctrl-1 = <&wf_dbdc_pins>; +}; + +&crypto { + status = "okay"; +}; + +&pio { + eth_pins: eth-pins { + mux { + function = "eth"; + groups = "switch_int", "mdc_mdio"; + }; + }; + + spic_pins_g2: spic-pins-29-to-32 { + mux { + function = "spi"; + groups = "spi1_2"; + }; + }; + + spi_flash_pins: spi-flash-pins-33-to-38 { + mux { + function = "spi"; + groups = "spi0", "spi0_wp_hold"; + }; + conf-pu { + pins = "SPI2_CS", "SPI2_HOLD", "SPI2_WP"; + drive-strength = <8>; + mediatek,pull-up-adv = <0>; /* bias-disable */ + }; + conf-pd { + pins = "SPI2_CLK", "SPI2_MOSI", "SPI2_MISO"; + drive-strength = <8>; + mediatek,pull-down-adv = <0>; /* bias-disable */ + }; + }; + + uart0_pins: uart0-pins { + mux { + function = "uart"; + groups = "uart0"; + }; + }; + + uart1_pins: uart1-pins { + mux { + function = "uart"; + groups = "uart1"; + }; + }; + + uart2_pins: uart2-pins { + mux { + function = "uart"; + groups = "uart2"; + }; + }; + + wf_2g_5g_pins: wf_2g_5g-pins { + mux { + function = "wifi"; + groups = "wf_2g", "wf_5g"; + }; + conf { + pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4", + "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6", + "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10", + "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1", + "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0", + "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8", + "WF1_TOP_CLK", "WF1_TOP_DATA"; + drive-strength = <4>; + }; + }; + + wf_dbdc_pins: wf_dbdc-pins { + mux { + function = "wifi"; + groups = "wf_dbdc"; + }; + conf { + pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4", + "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6", + "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10", + "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1", + "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0", + "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8", + "WF1_TOP_CLK", "WF1_TOP_DATA"; + drive-strength = <4>; + }; + }; + + usb-oc-hog { + gpio-hog; + gpios = <7 GPIO_ACTIVE_LOW>; + input; + line-name = "usb-oc"; + }; +}; + +&spi1 { + pinctrl-names = "default"; + pinctrl-0 = <&spic_pins_g2>; + status = "okay"; + + proslic_spi: proslic_spi@0 { + compatible = "silabs,proslic_spi"; + reg = <0>; + spi-max-frequency = <10000000>; + spi-cpha = <1>; + spi-cpol = <1>; + channel_count = <1>; + debug_level = <4>; /* 1 = TRC, 2 = DBG, 4 = ERR */ + reset_gpio = <&pio 25 GPIO_ACTIVE_HIGH>; + ig,enable-spi = <1>; /* 1: Enable, 0: Disable */ + }; +}; + +&ssusb { + vusb33-supply = <®_3p3v>; + vbus-supply = <®_5v>; + status = "okay"; +}; + +&trng { + status = "okay"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins>; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>; + status = "disabled"; + + /* EFR32MG21 Zigbee (BOOT)*/ +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&uart2_pins>; + status = "disabled"; + + /* EFR32MG21 Zigbee */ +}; + +&usb_phy { + status = "okay"; +}; diff --git a/target/linux/mediatek/dts/mt7986a-zyxel-ex5601-t0-stock.dts b/target/linux/mediatek/dts/mt7986a-zyxel-ex5601-t0-stock.dts index 331150d85d..987510d486 100644 --- a/target/linux/mediatek/dts/mt7986a-zyxel-ex5601-t0-stock.dts +++ b/target/linux/mediatek/dts/mt7986a-zyxel-ex5601-t0-stock.dts @@ -6,6 +6,7 @@ /dts-v1/; #include "mt7986a.dtsi" +#include "mt7986a-zyxel-ex5601-t0-common.dtsi" #include #include @@ -13,556 +14,111 @@ model = "Zyxel EX5601-T0"; compatible = "zyxel,ex5601-t0", "mediatek,mt7986a-rfb-snand"; - aliases { - serial0 = &uart0; + memory@40000000 { + device_type = "memory"; + reg = <0x40000000 0x20000000>; }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - memory { - reg = <0 0x40000000 0 0x40000000>; - }; - - reg_1p8v: regulator-1p8v { - compatible = "regulator-fixed"; - regulator-name = "fixed-1.8V"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-boot-on; - regulator-always-on; - }; - - reg_3p3v: regulator-3p3v { - compatible = "regulator-fixed"; - regulator-name = "fixed-3.3V"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-boot-on; - regulator-always-on; - }; - - reg_5v: regulator-5v { - compatible = "regulator-fixed"; - regulator-name = "fixed-5V"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - regulator-boot-on; - regulator-always-on; - }; - - gpio-keys { - compatible = "gpio-keys"; - poll-interval = <20>; - - reset-button { - label = "reset"; - gpios = <&pio 21 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - wlan-button { - label = "wlan"; - gpios = <&pio 11 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - wps-button { - label = "wps"; - gpios = <&pio 56 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - zyleds { - compatible = "gpio-leds"; - - led_green_wifi24g { - label = "zyled-green-wifi24g"; - gpios = <&pio 1 GPIO_ACTIVE_LOW>; - default-state = "off"; - }; - - led_green_wifi5g { - label = "zyled-green-wifi5g"; - gpios = <&pio 2 GPIO_ACTIVE_LOW>; - default-state = "off"; - }; - - led_green_inet { - label = "zyled-green-inet"; - gpios = <&pio 14 GPIO_ACTIVE_LOW>; - default-state = "off"; - }; - - led_red_inet { - label = "zyled-red-inet"; - gpios = <&pio 15 GPIO_ACTIVE_LOW>; - default-state = "off"; - }; - - led_green_pwr { - label = "zyled-green-pwr"; - gpios = <&pio 13 GPIO_ACTIVE_LOW>; - linux,default-trigger = "timer"; /* Default blinking */ - led-pattern = <125 125>; /* Fast blink is 4 HZ */ - }; - - led_red_pwr { - label = "zyled-red-pwr"; - gpios = <&pio 12 GPIO_ACTIVE_LOW>; - default-state = "off"; - }; - - led_green_fxs { - label = "zyled-green-fxs"; - gpios = <&pio 16 GPIO_ACTIVE_HIGH>; - default-state = "off"; - }; - - led_amber_fxs { - label = "zyled-amber-fxs"; - gpios = <&pio 17 GPIO_ACTIVE_HIGH>; - default-state = "off"; - }; - - led_amber_wps24g { - label = "zyled-amber-wps24g"; - gpios = <&pio 18 GPIO_ACTIVE_HIGH>; - default-state = "off"; - }; - - led_amber_wps5g { - label = "zyled-amber-wps5g"; - gpios = <&pio 19 GPIO_ACTIVE_HIGH>; - default-state = "off"; - }; - - led_green_lan { - label = "zyled-green-lan"; - gpios = <&pio 20 GPIO_ACTIVE_HIGH>; - default-state = "off"; - }; - - led_green_sfp { - label = "zyled-green-sfp"; - gpios = <&pio 24 GPIO_ACTIVE_HIGH>; - default-state = "off"; - }; - - }; - }; -ð { - status = "okay"; - - gmac0: mac@0 { - compatible = "mediatek,eth-mac"; - reg = <0>; - phy-mode = "2500base-x"; - - nvmem-cells = <&macaddr_factory_002a>; - nvmem-cell-names = "mac-address"; - - fixed-link { - speed = <2500>; - full-duplex; - pause; - }; - }; - - gmac1: mac@1 { - compatible = "mediatek,eth-mac"; - reg = <1>; - phy-mode = "2500base-x"; - phy = <&phy6>; - - nvmem-cells = <&macaddr_factory_0024>; - nvmem-cell-names = "mac-address"; - }; - - mdio: mdio-bus { - #address-cells = <1>; - #size-cells = <0>; - reset-gpios = <&pio 6 GPIO_ACTIVE_LOW>; - reset-delay-us = <1500000>; - reset-post-delay-us = <1000000>; - - phy5: phy@5 { - compatible = "ethernet-phy-ieee802.3-c45"; - reg = <5>; - }; - - phy6: phy@6 { - compatible = "ethernet-phy-ieee802.3-c45"; - reg = <6>; - }; - - switch@1f { - compatible = "mediatek,mt7531"; - reg = <31>; - reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - port@1 { - reg = <1>; - label = "lan1"; - }; - - port@2 { - reg = <2>; - label = "lan2"; - }; - - port@3 { - reg = <3>; - label = "lan3"; - }; - - port@5 { - reg = <5>; - label = "lan4"; - phy-mode = "2500base-x"; - phy = <&phy5>; - }; - - port@6 { - reg = <6>; - ethernet = <&gmac0>; - phy-mode = "2500base-x"; - - fixed-link { - speed = <2500>; - full-duplex; - pause; - }; - }; - }; - }; - }; +&spi_nand { + mediatek,nmbm; + mediatek,bmt-max-ratio = <1>; + mediatek,bmt-max-reserved-blocks = <64>; }; -&watchdog { - status = "okay"; -}; +&nand_partitions { -&wifi { - status = "okay"; - pinctrl-names = "default", "dbdc"; - pinctrl-0 = <&wf_2g_5g_pins>; - pinctrl-1 = <&wf_dbdc_pins>; - mediatek,mtd-eeprom = <&factory 0x0>; - nvmem-cells = <&macaddr_factory_0004>; - nvmem-cell-names = "mac-address"; -}; - -&crypto { - status = "okay"; -}; - -&mmc0 { - pinctrl-names = "default", "state_uhs"; - pinctrl-0 = <&mmc0_pins_default>; - pinctrl-1 = <&mmc0_pins_uhs>; - bus-width = <8>; - max-frequency = <200000000>; - cap-mmc-highspeed; - mmc-hs200-1_8v; - mmc-hs400-1_8v; - hs400-ds-delay = <0x14014>; - vmmc-supply = <®_3p3v>; - vqmmc-supply = <®_1p8v>; - non-removable; - no-sd; - no-sdio; - status = "disabled"; -}; - -&pcie { - pinctrl-names = "default"; - pinctrl-0 = <&pcie_pins>; - status = "okay"; -}; - -&pcie_phy { - status = "okay"; -}; - -&pio { - mmc0_pins_default: mmc0-pins { - mux { - function = "emmc"; - groups = "emmc_51"; - }; - conf-cmd-dat { - pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2", - "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5", - "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD"; - input-enable; - drive-strength = <4>; - mediatek,pull-up-adv = <1>; /* pull-up 10K */ - }; - conf-clk { - pins = "EMMC_CK"; - drive-strength = <6>; - mediatek,pull-down-adv = <2>; /* pull-down 50K */ - }; - conf-ds { - pins = "EMMC_DSL"; - mediatek,pull-down-adv = <2>; /* pull-down 50K */ - }; - conf-rst { - pins = "EMMC_RSTB"; - drive-strength = <4>; - mediatek,pull-up-adv = <1>; /* pull-up 10K */ - }; + partition@0 { + label = "BL2"; + reg = <0x00000 0x0100000>; + read-only; }; - mmc0_pins_uhs: mmc0-uhs-pins { - mux { - function = "emmc"; - groups = "emmc_51"; - }; - conf-cmd-dat { - pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2", - "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5", - "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD"; - input-enable; - drive-strength = <4>; - mediatek,pull-up-adv = <1>; /* pull-up 10K */ - }; - conf-clk { - pins = "EMMC_CK"; - drive-strength = <6>; - mediatek,pull-down-adv = <2>; /* pull-down 50K */ - }; - conf-ds { - pins = "EMMC_DSL"; - mediatek,pull-down-adv = <2>; /* pull-down 50K */ - }; - conf-rst { - pins = "EMMC_RSTB"; - drive-strength = <4>; - mediatek,pull-up-adv = <1>; /* pull-up 10K */ - }; + partition@100000 { + label = "u-boot-env"; + reg = <0x0100000 0x0080000>; }; - pcie_pins: pcie-pins { - mux { - function = "pcie"; - groups = "pcie_clk", "pcie_wake", "pcie_pereset"; - }; + factory: partition@180000 { + label = "Factory"; + reg = <0x180000 0x0200000>; + read-only; }; - spic_pins_g2: spic-pins-29-to-32 { - mux { - function = "spi"; - groups = "spi1_2"; - }; + partition@380000 { + label = "FIP"; + reg = <0x380000 0x01C0000>; + read-only; }; - spi_flash_pins: spi-flash-pins-33-to-38 { - mux { - function = "spi"; - groups = "spi0", "spi0_wp_hold"; - }; - conf-pu { - pins = "SPI2_CS", "SPI2_HOLD", "SPI2_WP"; - drive-strength = <8>; - mediatek,pull-up-adv = <0>; /* bias-disable */ - }; - conf-pd { - pins = "SPI2_CLK", "SPI2_MOSI", "SPI2_MISO"; - drive-strength = <8>; - mediatek,pull-down-adv = <0>; /* bias-disable */ - }; + partition@540000 { + label = "zloader"; + reg = <0x540000 0x0040000>; + read-only; }; - uart1_pins: uart1-pins { - mux { - function = "uart"; - groups = "uart1"; - }; + partition@580000 { + label = "ubi"; + reg = <0x580000 0x4000000>; }; - uart2_pins: uart2-pins { - mux { - function = "uart"; - groups = "uart2"; - }; - }; - - wf_2g_5g_pins: wf_2g_5g-pins { - mux { - function = "wifi"; - groups = "wf_2g", "wf_5g"; - }; - conf { - pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4", - "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6", - "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10", - "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1", - "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0", - "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8", - "WF1_TOP_CLK", "WF1_TOP_DATA"; - drive-strength = <4>; - }; + partition@4580000 { + label = "ubi2"; + reg = <0x4580000 0x4000000>; + read-only; }; - wf_dbdc_pins: wf_dbdc-pins { - mux { - function = "wifi"; - groups = "wf_dbdc"; - }; - conf { - pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4", - "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6", - "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10", - "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1", - "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0", - "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8", - "WF1_TOP_CLK", "WF1_TOP_DATA"; - drive-strength = <4>; - }; + partition@8580000 { + label = "zyubi"; + reg = <0x8580000 0x15A80000>; }; }; -&spi0 { - pinctrl-names = "default"; - pinctrl-0 = <&spi_flash_pins>; - cs-gpios = <0>, <0>; +&factory { + compatible = "nvmem-cells"; #address-cells = <1>; - #size-cells = <0>; - status = "okay"; + #size-cells = <1>; - spi_nand: spi_nand@0 { + nvmem-layout { + compatible = "fixed-layout"; #address-cells = <1>; - #size-cells = <1>; - compatible = "spi-nand"; - reg = <1>; - spi-max-frequency = <10000000>; - spi-tx-bus-width = <4>; - spi-rx-bus-width = <4>; - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; + eeprom_factory: eeprom@0 { #size-cells = <1>; + reg = <0x0 0x1000>; + }; - partition@0 { - label = "BL2"; - reg = <0x00000 0x0100000>; - read-only; - }; - - partition@100000 { - label = "u-boot-env"; - reg = <0x0100000 0x0080000>; - }; - - factory: partition@180000 { - label = "Factory"; - reg = <0x180000 0x0200000>; - read-only; - }; - - partition@380000 { - label = "FIP"; - reg = <0x380000 0x01C0000>; - read-only; - }; - - partition@540000 { - label = "zloader"; - reg = <0x540000 0x0040000>; - read-only; - }; - - partition@580000 { - label = "ubi"; - reg = <0x580000 0x4000000>; - }; - - partition@4580000 { - label = "ubi2"; - reg = <0x4580000 0x4000000>; - read-only; - }; - - partition@8580000 { - label = "zyubi"; - reg = <0x8580000 0x15A80000>; - }; + macaddr_factory_0004: macaddr@0004 { + compatible = "mac-base"; + reg = <0x0004 0x6>; + #nvmem-cell-cells = <1>; }; - }; -}; -&spi1 { - pinctrl-names = "default"; - pinctrl-0 = <&spic_pins_g2>; - status = "okay"; + macaddr_factory_0024: macaddr@0024 { + compatible = "mac-base"; + reg = <0x0024 0x6>; + #nvmem-cell-cells = <1>; + }; - proslic_spi: proslic_spi@0 { - compatible = "silabs,proslic_spi"; - reg = <0>; - spi-max-frequency = <10000000>; - spi-cpha = <1>; - spi-cpol = <1>; - channel_count = <1>; - debug_level = <4>; /* 1 = TRC, 2 = DBG, 4 = ERR */ - reset_gpio = <&pio 7 GPIO_ACTIVE_HIGH>; - ig,enable-spi = <1>; /* 1: Enable, 0: Disable */ + macaddr_factory_002a: macaddr@002a { + compatible = "mac-base"; + reg = <0x002a 0x6>; + #nvmem-cell-cells = <1>; + }; }; }; -&ssusb { - vusb33-supply = <®_3p3v>; - vbus-supply = <®_5v>; - status = "okay"; -}; - -&trng { - status = "okay"; -}; - -&uart0 { - status = "okay"; -}; - -&uart1 { - pinctrl-names = "default"; - pinctrl-0 = <&uart1_pins>; - status = "okay"; -}; - -&uart2 { - pinctrl-names = "default"; - pinctrl-0 = <&uart2_pins>; - status = "okay"; +&gmac0 { + nvmem-cells = <&macaddr_factory_002a 0>; + nvmem-cell-names = "mac-address"; }; -&usb_phy { - status = "okay"; +&gmac1 { + nvmem-cells = <&macaddr_factory_0024 0>; + nvmem-cell-names = "mac-address"; }; -&factory { - compatible = "nvmem-cells"; - #address-cells = <1>; - #size-cells = <1>; - - macaddr_factory_0004: macaddr@0004 { - reg = <0x0004 0x6>; - }; - - macaddr_factory_0024: macaddr@0024 { - reg = <0x0024 0x6>; - }; - - macaddr_factory_002a: macaddr@002a { - reg = <0x002a 0x6>; - }; +&wifi { + nvmem-cells = <&eeprom_factory>; + nvmem-cell-names = "eeprom"; }; diff --git a/target/linux/mediatek/dts/mt7986a-zyxel-ex5601-t0-ubootmod.dts b/target/linux/mediatek/dts/mt7986a-zyxel-ex5601-t0-ubootmod.dts new file mode 100644 index 0000000000..a300e2052d --- /dev/null +++ b/target/linux/mediatek/dts/mt7986a-zyxel-ex5601-t0-ubootmod.dts @@ -0,0 +1,106 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright (C) 2021 MediaTek Inc. + * Author: Sam.Shih + */ + +/dts-v1/; +#include "mt7986a.dtsi" +#include "mt7986a-zyxel-ex5601-t0-common.dtsi" +#include +#include + +/ { + model = "Zyxel EX5601-T0 ubootmod"; + compatible = "zyxel,ex5601-t0-ubootmod", "mediatek,mt7986a"; + memory@40000000 { + device_type = "memory"; + reg = <0x40000000 0x20000000>; + }; +}; + +&nand_partitions { + partition@0 { + label = "bl2"; + reg = <0x0 0x100000>; + read-only; + }; + + partition@100000 { + label = "u-boot-env"; + reg = <0x0100000 0x0080000>; + read-only; + }; + + factory: partition@180000 { + label = "Factory"; + reg = <0x180000 0x0200000>; + read-only; + }; + + partition@380000 { + label = "fip"; + reg = <0x380000 0x0200000>; + read-only; + }; + + partition@540000 { + label = "zloader"; + reg = <0x540000 0x0040000>; + read-only; + }; + + partition@580000 { + label = "ubi"; + reg = <0x580000 0x1da80000>; + }; +}; + +&factory { + compatible = "nvmem-cells"; + #address-cells = <1>; + #size-cells = <1>; + + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + + eeprom_factory: eeprom@0 { + #size-cells = <1>; + reg = <0x0 0x1000>; + }; + + macaddr_factory_0004: macaddr@0004 { + compatible = "mac-base"; + reg = <0x0004 0x6>; + #nvmem-cell-cells = <1>; + }; + + macaddr_factory_0024: macaddr@0024 { + compatible = "mac-base"; + reg = <0x0024 0x6>; + #nvmem-cell-cells = <1>; + }; + + macaddr_factory_002a: macaddr@002a { + compatible = "mac-base"; + reg = <0x002a 0x6>; + #nvmem-cell-cells = <1>; + }; + }; +}; + +&gmac0 { + nvmem-cells = <&macaddr_factory_002a 0>; + nvmem-cell-names = "mac-address"; +}; + +&gmac1 { + nvmem-cells = <&macaddr_factory_0024 0>; + nvmem-cell-names = "mac-address"; +}; + +&wifi { + nvmem-cells = <&eeprom_factory>; + nvmem-cell-names = "eeprom"; +}; diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds index cdeaa6c5c5..75c8fcda9b 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds @@ -42,6 +42,13 @@ xiaomi,redmi-router-ax6000-stock|\ xiaomi,redmi-router-ax6000-ubootmod) ucidef_set_led_netdev "wan" "wan" "rgb:network" "wan" ;; +zyxel_ex5601-t0-stock|\ +zyxel,ex5601-t0-ubootmod) + ucidef_set_led_netdev "lan" "LAN" "green:lan" "eth0" "link tx rx" + ucidef_set_led_netdev "wan" "WAN" "green:inet" "eth1" "link tx rx" + ucidef_set_led_netdev "wifi-24g" "WIFI-2.4G" "green:wifi24g" "phy0-ap0" "link tx rx" + ucidef_set_led_netdev "wifi-5g" "WIFI-5G" "green:wifi5g" "phy1-ap0" "link tx rx" + ;; esac board_config_flush diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network index 2e978be680..a48fbbc79c 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network @@ -73,6 +73,10 @@ mediatek_setup_interfaces() xiaomi,redmi-router-ax6000-ubootmod) ucidef_set_interfaces_lan_wan "lan2 lan3 lan4" wan ;; + zyxel,ex5601-t0-stock|\ + zyxel,ex5601-t0-ubootmod) + ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" eth1 + ;; *) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" wan ;; diff --git a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac index f8ebc1da42..e6378dd498 100644 --- a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac +++ b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac @@ -107,7 +107,8 @@ case "$board" in ;; routerich,ax3000|\ zbtlink,zbt-z8102ax|\ - zyxel,ex5601-t0) + zyxel,ex5601-t0|\ + zyxel,ex5601-t0-ubootmod) addr=$(mtd_get_mac_binary "Factory" 0x4) [ "$PHYNBR" = "1" ] && macaddr_add $addr 1 > /sys${DEVPATH}/macaddress ;; diff --git a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh index e3b042c876..9b3ebe92f1 100755 --- a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh +++ b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh @@ -142,6 +142,11 @@ platform_do_upgrade() { CI_ROOT_UBIPART=ubi nand_do_upgrade "$1" ;; + zyxel,ex5601-t0-ubootmod) + CI_KERNPART="fit" + CI_ROOTPART="ubi_rootfs" + nand_do_upgrade "$1" + ;; *) nand_do_upgrade "$1" ;; diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk index 194319a228..7daac6a1fa 100644 --- a/target/linux/mediatek/image/filogic.mk +++ b/target/linux/mediatek/image/filogic.mk @@ -801,10 +801,11 @@ TARGET_DEVICES += zbtlink_zbt-z8102ax define Device/zyxel_ex5601-t0-stock DEVICE_VENDOR := Zyxel - DEVICE_MODEL := EX5601-T0 (stock layout) + DEVICE_MODEL := EX5601-T0 + DEVICE_VARIANT := (stock layout) DEVICE_DTS := mt7986a-zyxel-ex5601-t0-stock DEVICE_DTS_DIR := ../dts - DEVICE_PACKAGES := kmod-mt7986-firmware mt7986-wo-firmware + DEVICE_PACKAGES := kmod-mt7986-firmware mt7986-wo-firmware kmod-usb3 SUPPORTED_DEVICES := mediatek,mt7986a-rfb-snand UBINIZE_OPTS := -E 5 BLOCKSIZE := 256k @@ -821,6 +822,35 @@ define Device/zyxel_ex5601-t0-stock endef TARGET_DEVICES += zyxel_ex5601-t0-stock +define Device/zyxel_ex5601-t0-ubootmod + DEVICE_VENDOR := Zyxel + DEVICE_MODEL := EX5601-T0 + DEVICE_VARIANT := (OpenWrt U-Boot layout) + DEVICE_DTS := mt7986a-zyxel-ex5601-t0-ubootmod + DEVICE_DTS_DIR := ../dts + DEVICE_PACKAGES := kmod-mt7986-firmware mt7986-wo-firmware kmod-usb3 + KERNEL_INITRAMFS_SUFFIX := -recovery.itb + IMAGES := sysupgrade.itb + UBINIZE_OPTS := -E 5 + BLOCKSIZE := 256k + PAGESIZE := 4096 + KERNEL_IN_UBI := 1 + UBOOTENV_IN_UBI := 1 + KERNEL := kernel-bin | lzma + KERNEL_INITRAMFS := kernel-bin | lzma | \ + fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd + IMAGE/sysupgrade.itb := append-kernel | \ + fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-static-with-rootfs | append-metadata + ARTIFACTS := preloader.bin bl31-uboot.fip + ARTIFACT/preloader.bin := mt7986-bl2 spim-nand-4k-ddr4 + ARTIFACT/bl31-uboot.fip := mt7986-bl31-uboot zyxel_ex5601-t0 +ifneq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),) + ARTIFACTS += initramfs-factory.ubi + ARTIFACT/initramfs-factory.ubi := append-image-stage initramfs-recovery.itb | ubinize-kernel +endif +endef +TARGET_DEVICES += zyxel_ex5601-t0-ubootmod + define Device/zyxel_ex5700-telenor DEVICE_VENDOR := ZyXEL DEVICE_MODEL := EX5700 (Telenor) -- 2.30.2