From 67ce9aedd6d3f7995351f478e79e570c01ea71fc Mon Sep 17 00:00:00 2001 From: Pawel Dembicki Date: Sun, 26 Jan 2020 17:22:28 +0100 Subject: [PATCH] kirkwood: add support for Check Point L-50 This patch adds support for the Check Point L-50 from 600/1100 series routers. Specification: -CPU: Marvell Kirkwood 88F6281 1200MHz -RAM: 512MB -Flash: NAND 512MB -WiFi: mPCIe card based on Atheros AR9287 b/g/n -WAN: 1 Gigabit Port (Marvell 88E1116R PHY) -LAN: 9 Gigabit Ports (2x Marvell 88E6171(5+4)) -USB: 2x USB2.0 -Express card slot -SD card slot -Serial console: RJ-45 115200 8n1 -Unsupported DSL Known issues: -DSL not supported -Expresscard not tested Installation: Step one -> backup: make backup u-boot and env for revert stock posibility make backup dsl_mac_addr, dmz_mac_addr, eth1addr, ethaddr and all lanX_mac_addr Step two -> Use kwboot tool to upload openwrt u-boot to RAM: run kwboot: "kwboot -B 115200 /dev/ttyUSB0 -b u-boot.kwb -p -t" end start u-boot Step three -> Restore macs (e.g. below): setenv eth1addr 00:1C:XX:XX:XX:6C setenv ethaddr 00:1C:XX:XX:XX:6B setenv lan1_mac_addr 00:1C:XX:XX:XX:6C setenv lan2_mac_addr 00:1C:XX:XX:XX:6D setenv lan3_mac_addr 00:1C:XX:XX:XX:6E setenv lan4_mac_addr 00:1C:XX:XX:XX:6F setenv lan5_mac_addr 00:1C:XX:XX:XX:70 setenv lan6_mac_addr 00:1C:XX:XX:XX:71 setenv lan7_mac_addr 00:1C:XX:XX:XX:72 setenv lan8_mac_addr 00:1C:XX:XX:XX:73 setenv dmz_mac_addr 00:1C:XX:XX:XX:74 setenv dsl_mac_addr 00:1C:XX:XX:XX:75 Step four -> flash u-boot: mw 0x0800000 0xffff 0x100000 nand erase 0x0 100000 tftp 0x0800000 openwrt-kirkwood-l50-u-boot.kwb nand write 0x0800000 0x0 0x100000 saveenv Step five -> run initramfs image: tftpboot 0x02000000 openwrt.bin; bootm 0x02000000; Step six -> install sysupgrade OpenWrt image: copy to /tmp/ sysupgrade image run sysupgrade Back to stock: Restore original u-boot end env. Install factory image via stock u-boot. Signed-off-by: Pawel Dembicki --- package/boot/uboot-envtools/files/kirkwood | 1 + .../base-files/etc/board.d/02_network | 3 + .../base-files/etc/board.d/03_gpio_switches | 18 + .../base-files/lib/preinit/07_set_iface_mac | 25 + target/linux/kirkwood/config-5.4 | 1 + target/linux/kirkwood/image/Makefile | 10 + ...-kirkwood-Add-Check-Point-L-50-board.patch | 485 ++++++++++++++++++ .../linux/kirkwood/patches-5.4/111-l-50.patch | 47 ++ 8 files changed, 590 insertions(+) create mode 100755 target/linux/kirkwood/base-files/etc/board.d/03_gpio_switches create mode 100644 target/linux/kirkwood/base-files/lib/preinit/07_set_iface_mac create mode 100644 target/linux/kirkwood/patches-5.4/001-ARM-dts-kirkwood-Add-Check-Point-L-50-board.patch create mode 100644 target/linux/kirkwood/patches-5.4/111-l-50.patch diff --git a/package/boot/uboot-envtools/files/kirkwood b/package/boot/uboot-envtools/files/kirkwood index 5e87dd1d62e..a099c925ea2 100644 --- a/package/boot/uboot-envtools/files/kirkwood +++ b/package/boot/uboot-envtools/files/kirkwood @@ -13,6 +13,7 @@ touch /etc/config/ubootenv board=$(board_name) case "$board" in +checkpoint,l-50|\ cloudengines,pogoe02|\ cloudengines,pogoplugv4|\ iom,ix2-200|\ diff --git a/target/linux/kirkwood/base-files/etc/board.d/02_network b/target/linux/kirkwood/base-files/etc/board.d/02_network index a86c57117dd..658ce133467 100755 --- a/target/linux/kirkwood/base-files/etc/board.d/02_network +++ b/target/linux/kirkwood/base-files/etc/board.d/02_network @@ -11,6 +11,9 @@ board_config_update board=$(board_name) case "$board" in +"checkpoint,l-50") + ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 lan5 lan6 lan7 lan8 dmz" "eth0" + ;; "cisco,on100") ucidef_set_interface_lan "eth0 eth1" ;; diff --git a/target/linux/kirkwood/base-files/etc/board.d/03_gpio_switches b/target/linux/kirkwood/base-files/etc/board.d/03_gpio_switches new file mode 100755 index 00000000000..046f8d4d207 --- /dev/null +++ b/target/linux/kirkwood/base-files/etc/board.d/03_gpio_switches @@ -0,0 +1,18 @@ +#!/bin/sh + +. /lib/functions/uci-defaults.sh + +board_config_update + +board=$(board_name) + +case "$board" in +checkpoint,l-50) + ucidef_add_gpio_switch "mpcie-rst" "mPCIE Card reset" "502" "1" + ucidef_add_gpio_switch "exp-card-rst" "Express Card reset" "497" "1" + ;; +esac + +board_config_flush + +exit 0 diff --git a/target/linux/kirkwood/base-files/lib/preinit/07_set_iface_mac b/target/linux/kirkwood/base-files/lib/preinit/07_set_iface_mac new file mode 100644 index 00000000000..75e9e886d9c --- /dev/null +++ b/target/linux/kirkwood/base-files/lib/preinit/07_set_iface_mac @@ -0,0 +1,25 @@ +. /lib/functions.sh +. /lib/functions/system.sh + +preinit_set_mac_address() { + local mac + + case $(board_name) in + checkpoint,l-50) + mac=$(mtd_get_mac_ascii bootldr-env lan1_mac_addr) + + ip link set dev lan1 address $mac 2>/dev/null + ip link set dev lan2 address $(macaddr_add $mac 1) 2>/dev/null + ip link set dev lan3 address $(macaddr_add $mac 2) 2>/dev/null + ip link set dev lan4 address $(macaddr_add $mac 3) 2>/dev/null + ip link set dev lan5 address $(macaddr_add $mac 4) 2>/dev/null + ip link set dev lan6 address $(macaddr_add $mac 5) 2>/dev/null + ip link set dev lan7 address $(macaddr_add $mac 6) 2>/dev/null + ip link set dev lan8 address $(macaddr_add $mac 7) 2>/dev/null + ip link set dev dmz address $(macaddr_add $mac 8) 2>/dev/null + ip link set dev dsl address $(macaddr_add $mac 9) 2>/dev/null + ;; + esac +} + +boot_hook_add preinit_main preinit_set_mac_address diff --git a/target/linux/kirkwood/config-5.4 b/target/linux/kirkwood/config-5.4 index 5529bf89df8..61efa07d91c 100644 --- a/target/linux/kirkwood/config-5.4 +++ b/target/linux/kirkwood/config-5.4 @@ -282,6 +282,7 @@ CONFIG_PINCTRL=y CONFIG_PINCTRL_KIRKWOOD=y CONFIG_PINCTRL_MVEBU=y # CONFIG_PINCTRL_SINGLE is not set +CONFIG_PINCTRL_SX150X=y CONFIG_PLAT_ORION=y CONFIG_POWER_RESET=y CONFIG_POWER_RESET_GPIO=y diff --git a/target/linux/kirkwood/image/Makefile b/target/linux/kirkwood/image/Makefile index 8cc69195b44..ba93fffeb21 100644 --- a/target/linux/kirkwood/image/Makefile +++ b/target/linux/kirkwood/image/Makefile @@ -28,6 +28,16 @@ define Device/Default SUPPORTED_DEVICES = $(subst _,$(comma),$(1)) $$(BOARD_NAME) endef +define Device/checkpoint_l-50 + DEVICE_VENDOR := Check Point + DEVICE_MODEL := L-50 + DEVICE_DTS := kirkwood-l-50 + DEVICE_PACKAGES := kmod-ath9k kmod-gpio-button-hotplug kmod-mvsdio \ + kmod-rtc-s35390a kmod-usb-ledtrig-usbport wpad-basic + IMAGES := sysupgrade.bin +endef +TARGET_DEVICES += checkpoint_l-50 + define Device/cisco_on100 DEVICE_VENDOR := Cisco Systems DEVICE_MODEL := ON100 diff --git a/target/linux/kirkwood/patches-5.4/001-ARM-dts-kirkwood-Add-Check-Point-L-50-board.patch b/target/linux/kirkwood/patches-5.4/001-ARM-dts-kirkwood-Add-Check-Point-L-50-board.patch new file mode 100644 index 00000000000..52caee7b407 --- /dev/null +++ b/target/linux/kirkwood/patches-5.4/001-ARM-dts-kirkwood-Add-Check-Point-L-50-board.patch @@ -0,0 +1,485 @@ +From efa968c18abab78c5e0c40a853caf286c3629a59 Mon Sep 17 00:00:00 2001 +From: Pawel Dembicki +Date: Tue, 17 Mar 2020 21:28:01 +0100 +Subject: [PATCH v3] ARM: dts: kirkwood: Add Check Point L-50 board + +This patch adds dts for the Check Point L-50 from 600/1100 series +routers. + +Specification: +-CPU: Marvell Kirkwood 88F6821 1200MHz +-RAM: 512MB +-Flash: NAND 512MB +-WiFi: mPCIe card based on Atheros AR9287 b/g/n +-WAN: 1 Gigabit Port (Marvell 88E1116R PHY) +-LAN: 9 Gigabit Ports (2x Marvell 88E6171(5+3)) +-USB: 2x USB2.0 +-Express card slot +-SD card slot +-Serial console: RJ-45 115200 8n1 +-Unsupported DSL + +Reviewed-by: Andrew Lunn +Signed-off-by: Pawel Dembicki +--- +Changes in v3: +- fix typo and code style issues pointed by OpenWrt guys +Changes in v2: +- none + + arch/arm/boot/dts/Makefile | 1 + + arch/arm/boot/dts/kirkwood-l-50.dts | 438 ++++++++++++++++++++++++++++ + 2 files changed, 439 insertions(+) + create mode 100644 arch/arm/boot/dts/kirkwood-l-50.dts + +--- a/arch/arm/boot/dts/Makefile ++++ b/arch/arm/boot/dts/Makefile +@@ -270,6 +270,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \ + kirkwood-iomega_ix2_200.dtb \ + kirkwood-is2.dtb \ + kirkwood-km_kirkwood.dtb \ ++ kirkwood-l-50.dtb \ + kirkwood-laplug.dtb \ + kirkwood-linkstation-lsqvl.dtb \ + kirkwood-linkstation-lsvl.dtb \ +--- /dev/null ++++ b/arch/arm/boot/dts/kirkwood-l-50.dts +@@ -0,0 +1,438 @@ ++// SPDX-License-Identifier: GPL-2.0 ++/* ++ * Check Point L-50 Board Description ++ * Copyright 2020 Pawel Dembicki ++ */ ++ ++/dts-v1/; ++ ++#include "kirkwood.dtsi" ++#include "kirkwood-6281.dtsi" ++ ++/ { ++ model = "Check Point L-50"; ++ compatible = "checkpoint,l-50", "marvell,kirkwood-88f6281", "marvell,kirkwood"; ++ ++ memory { ++ device_type = "memory"; ++ reg = <0x00000000 0x20000000>; ++ }; ++ ++ chosen { ++ bootargs = "console=ttyS0,115200n8"; ++ stdout-path = &uart0; ++ }; ++ ++ ocp@f1000000 { ++ pinctrl: pin-controller@10000 { ++ pinctrl-0 = <&pmx_led38 &pmx_sysrst &pmx_button29>; ++ pinctrl-names = "default"; ++ ++ pmx_sysrst: pmx-sysrst { ++ marvell,pins = "mpp6"; ++ marvell,function = "sysrst"; ++ }; ++ ++ pmx_button29: pmx_button29 { ++ marvell,pins = "mpp29"; ++ marvell,function = "gpio"; ++ }; ++ ++ pmx_led38: pmx_led38 { ++ marvell,pins = "mpp38"; ++ marvell,function = "gpio"; ++ }; ++ ++ pmx_sdio_cd: pmx-sdio-cd { ++ marvell,pins = "mpp46"; ++ marvell,function = "gpio"; ++ }; ++ }; ++ ++ serial@12000 { ++ status = "okay"; ++ }; ++ ++ mvsdio@90000 { ++ status = "okay"; ++ cd-gpios = <&gpio1 14 9>; ++ }; ++ ++ i2c@11000 { ++ status = "okay"; ++ clock-frequency = <400000>; ++ ++ gpio2: gpio-expander@20{ ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ compatible = "semtech,sx1505q"; ++ reg = <0x20>; ++ ++ gpio-controller; ++ }; ++ ++ /* Three GPIOs from 0x21 exp. are undescribed in dts: ++ * 1: DSL module reset (active low) ++ * 5: mPCIE reset (active low) ++ * 6: Express card reset (active low) ++ */ ++ gpio3: gpio-expander@21{ ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ compatible = "semtech,sx1505q"; ++ reg = <0x21>; ++ ++ gpio-controller; ++ }; ++ ++ rtc@30 { ++ compatible = "s35390a"; ++ reg = <0x30>; ++ }; ++ }; ++ }; ++ ++ leds { ++ compatible = "gpio-leds"; ++ ++ status_green { ++ label = "l-50:green:status"; ++ gpios = <&gpio1 6 GPIO_ACTIVE_LOW>; ++ }; ++ ++ status_red { ++ label = "l-50:red:status"; ++ gpios = <&gpio3 2 GPIO_ACTIVE_LOW>; ++ }; ++ ++ wifi { ++ label = "l-50:green:wifi"; ++ gpios = <&gpio2 7 GPIO_ACTIVE_LOW>; ++ linux,default-trigger = "phy0tpt"; ++ }; ++ ++ internet_green { ++ label = "l-50:green:internet"; ++ gpios = <&gpio2 3 GPIO_ACTIVE_LOW>; ++ }; ++ ++ internet_red { ++ label = "l-50:red:internet"; ++ gpios = <&gpio2 1 GPIO_ACTIVE_LOW>; ++ }; ++ ++ usb1_green { ++ label = "l-50:green:usb1"; ++ gpios = <&gpio2 0 GPIO_ACTIVE_LOW>; ++ linux,default-trigger = "usbport"; ++ trigger-sources = <&hub_port3>; ++ }; ++ ++ usb1_red { ++ label = "l-50:red:usb1"; ++ gpios = <&gpio2 4 GPIO_ACTIVE_LOW>; ++ }; ++ ++ usb2_green { ++ label = "l-50:green:usb2"; ++ gpios = <&gpio2 2 GPIO_ACTIVE_LOW>; ++ linux,default-trigger = "usbport"; ++ trigger-sources = <&hub_port1>; ++ }; ++ ++ usb2_red { ++ label = "l-50:red:usb2"; ++ gpios = <&gpio2 5 GPIO_ACTIVE_LOW>; ++ }; ++ }; ++ ++ usb2_pwr { ++ compatible = "regulator-fixed"; ++ regulator-name = "usb2_pwr"; ++ ++ regulator-min-microvolt = <5000000>; ++ regulator-max-microvolt = <5000000>; ++ gpio = <&gpio3 3 GPIO_ACTIVE_LOW>; ++ regulator-always-on; ++ }; ++ ++ usb1_pwr { ++ compatible = "regulator-fixed"; ++ regulator-name = "usb1_pwr"; ++ ++ regulator-min-microvolt = <5000000>; ++ regulator-max-microvolt = <5000000>; ++ gpio = <&gpio3 4 GPIO_ACTIVE_LOW>; ++ regulator-always-on; ++ }; ++ ++ mpcie_pwr { ++ compatible = "regulator-fixed"; ++ regulator-name = "mpcie_pwr"; ++ ++ regulator-min-microvolt = <3300000>; ++ regulator-max-microvolt = <3300000>; ++ gpio = <&gpio3 5 GPIO_ACTIVE_HIGH>; ++ enable-active-high; ++ regulator-always-on; ++ }; ++ ++ express_card_pwr { ++ compatible = "regulator-fixed"; ++ regulator-name = "express_card_pwr"; ++ ++ regulator-min-microvolt = <3300000>; ++ regulator-max-microvolt = <3300000>; ++ gpio = <&gpio3 7 GPIO_ACTIVE_HIGH>; ++ enable-active-high; ++ regulator-always-on; ++ }; ++ ++ keys { ++ compatible = "gpio-keys"; ++ ++ factory_defaults { ++ label = "factory_defaults"; ++ gpios = <&gpio0 29 GPIO_ACTIVE_LOW>; ++ linux,code = ; ++ }; ++ }; ++}; ++ ++&mdio { ++ status = "okay"; ++ ++ ethphy8: ethernet-phy@8 { ++ reg = <0x08>; ++ }; ++ ++ switch0: switch@10 { ++ compatible = "marvell,mv88e6085"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ reg = <0x10>; ++ dsa,member = <0 0>; ++ ++ ports { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ port@0 { ++ reg = <0>; ++ label = "lan5"; ++ }; ++ ++ port@1 { ++ reg = <1>; ++ label = "lan1"; ++ }; ++ ++ port@2 { ++ reg = <2>; ++ label = "lan6"; ++ }; ++ ++ port@3 { ++ reg = <3>; ++ label = "lan2"; ++ }; ++ ++ port@4 { ++ reg = <4>; ++ label = "lan7"; ++ }; ++ ++ switch0port5: port@5 { ++ reg = <5>; ++ phy-mode = "rgmii-txid"; ++ link = <&switch1port5>; ++ fixed-link { ++ speed = <1000>; ++ full-duplex; ++ }; ++ }; ++ ++ port@6 { ++ reg = <6>; ++ label = "cpu"; ++ phy-mode = "rgmii-id"; ++ ethernet = <ð1port>; ++ fixed-link { ++ speed = <1000>; ++ full-duplex; ++ }; ++ }; ++ }; ++ }; ++ ++ switch@11 { ++ compatible = "marvell,mv88e6085"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ reg = <0x11>; ++ dsa,member = <0 1>; ++ ++ ports { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ port@0 { ++ reg = <0>; ++ label = "lan3"; ++ }; ++ ++ port@1 { ++ reg = <1>; ++ label = "lan8"; ++ }; ++ ++ port@2 { ++ reg = <2>; ++ label = "lan4"; ++ }; ++ ++ port@3 { ++ reg = <3>; ++ label = "dmz"; ++ }; ++ ++ switch1port5: port@5 { ++ reg = <5>; ++ phy-mode = "rgmii-txid"; ++ link = <&switch0port5>; ++ fixed-link { ++ speed = <1000>; ++ full-duplex; ++ }; ++ }; ++ ++ port@6 { ++ reg = <6>; ++ label = "dsl"; ++ fixed-link { ++ speed = <100>; ++ full-duplex; ++ }; ++ }; ++ }; ++ }; ++}; ++ ++ð0 { ++ status = "okay"; ++ ethernet0-port@0 { ++ phy-handle = <ðphy8>; ++ }; ++}; ++ ++ð1 { ++ status = "okay"; ++ ethernet1-port@0 { ++ speed = <1000>; ++ duplex = <1>; ++ }; ++}; ++ ++&nand { ++ status = "okay"; ++ pinctrl-0 = <&pmx_nand>; ++ pinctrl-names = "default"; ++ ++ partition@0 { ++ label = "u-boot"; ++ reg = <0x00000000 0x000c0000>; ++ }; ++ ++ partition@a0000 { ++ label = "bootldr-env"; ++ reg = <0x000c0000 0x00040000>; ++ }; ++ ++ partition@100000 { ++ label = "kernel-1"; ++ reg = <0x00100000 0x00800000>; ++ }; ++ ++ partition@900000 { ++ label = "rootfs-1"; ++ reg = <0x00900000 0x07100000>; ++ }; ++ ++ partition@7a00000 { ++ label = "kernel-2"; ++ reg = <0x07a00000 0x00800000>; ++ }; ++ ++ partition@8200000 { ++ label = "rootfs-2"; ++ reg = <0x08200000 0x07100000>; ++ }; ++ ++ partition@f300000 { ++ label = "default_sw"; ++ reg = <0x0f300000 0x07900000>; ++ }; ++ ++ partition@16c00000 { ++ label = "logs"; ++ reg = <0x16c00000 0x01800000>; ++ }; ++ ++ partition@18400000 { ++ label = "preset_cfg"; ++ reg = <0x18400000 0x00100000>; ++ }; ++ ++ partition@18500000 { ++ label = "adsl"; ++ reg = <0x18500000 0x00100000>; ++ }; ++ ++ partition@18600000 { ++ label = "storage"; ++ reg = <0x18600000 0x07a00000>; ++ }; ++}; ++ ++&rtc { ++ status = "disabled"; ++}; ++ ++&pciec { ++ status = "okay"; ++}; ++ ++&pcie0 { ++ status = "okay"; ++}; ++ ++&sata_phy0 { ++ status = "disabled"; ++}; ++ ++&sata_phy1 { ++ status = "disabled"; ++}; ++ ++&usb0 { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ port@1 { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ reg = <1>; ++ #trigger-source-cells = <0>; ++ ++ hub_port1: port@1 { ++ reg = <1>; ++ #trigger-source-cells = <0>; ++ }; ++ ++ hub_port3: port@3 { ++ reg = <3>; ++ #trigger-source-cells = <0>; ++ }; ++ }; ++}; diff --git a/target/linux/kirkwood/patches-5.4/111-l-50.patch b/target/linux/kirkwood/patches-5.4/111-l-50.patch new file mode 100644 index 00000000000..b1679885ad6 --- /dev/null +++ b/target/linux/kirkwood/patches-5.4/111-l-50.patch @@ -0,0 +1,47 @@ +--- a/arch/arm/boot/dts/kirkwood-l-50.dts ++++ b/arch/arm/boot/dts/kirkwood-l-50.dts +@@ -18,6 +18,13 @@ + reg = <0x00000000 0x20000000>; + }; + ++ aliases { ++ led-boot = &led_status_green; ++ led-failsafe = &led_status_red; ++ led-running = &led_status_green; ++ led-upgrade = &led_status_red; ++ }; ++ + chosen { + bootargs = "console=ttyS0,115200n8"; + stdout-path = &uart0; +@@ -95,12 +102,12 @@ + leds { + compatible = "gpio-leds"; + +- status_green { ++ led_status_green: status_green { + label = "l-50:green:status"; + gpios = <&gpio1 6 GPIO_ACTIVE_LOW>; + }; + +- status_red { ++ led_status_red: status_red { + label = "l-50:red:status"; + gpios = <&gpio3 2 GPIO_ACTIVE_LOW>; + }; +@@ -349,13 +356,8 @@ + }; + + partition@100000 { +- label = "kernel-1"; +- reg = <0x00100000 0x00800000>; +- }; +- +- partition@900000 { +- label = "rootfs-1"; +- reg = <0x00900000 0x07100000>; ++ label = "ubi"; ++ reg = <0x00100000 0x07900000>; + }; + + partition@7a00000 { -- 2.30.2