From 65f606fb82e00d456a8de854b0e71c9b5ae2a0a1 Mon Sep 17 00:00:00 2001 From: Nick Hainke Date: Fri, 16 Sep 2022 14:21:31 +0200 Subject: [PATCH] ipq40xx: delete files used for building 5.10 kernel The kernel 5.15 now defaults. Remove unnecessary files. Reviewed-by: Robert Marko Signed-off-by: Nick Hainke --- target/linux/ipq40xx/config-5.10 | 500 ------------------ ...com-ipq4019-add-USB-devicetree-nodes.patch | 99 ---- ...ARM-dts-qcom-ipq4019-add-more-labels.patch | 44 -- ...com-ipq4019-add-SDHCI-VQMMC-LDO-node.patch | 35 -- .../104-clk-fix-apss-cpu-overclocking.patch | 115 ---- .../300-clk-qcom-ipq4019-add-ess-reset.patch | 52 -- ...-compressed-add-appended-DTB-section.patch | 48 -- ...d-set-ipq40xx-watchdog-to-allow-boot.patch | 66 --- ...msm-use-sdhci_set_clock-instead-of-s.patch | 24 - .../420-firmware-qcom-scm-disable-SDI.patch | 47 -- ...-firmware-qcom-scm-cold-boot-address.patch | 121 ----- ...-add-support-for-Toshiba-TC58NVG0S3H.patch | 29 - ...pecific-data-to-struct-skb_shared_in.patch | 43 -- ...019-add-shinfo-based-tagging-driver-.patch | 188 ------- ...ethernet-qualcomm-add-IPQESS-support.patch | 43 -- ...4019-add-ethernet-controller-DT-node.patch | 81 --- ...phy-define-PSGMII-PHY-interface-mode.patch | 61 --- ...comm-IPQ4019-built-in-switch-support.patch | 53 -- .../706-arm-dts-ipq4019-add-switch-node.patch | 98 ---- .../707-dt-bindings-net-add-QCA807x-PHY.patch | 61 --- ...8-net-phy-Add-Qualcom-QCA807x-driver.patch | 50 -- ...9-arm-dts-ipq4019-QCA807x-properties.patch | 61 --- .../850-soc-add-qualcomm-syscon.patch | 180 ------- .../900-dts-ipq4019-ap-dk01.1.patch | 176 ------ .../902-dts-ipq4019-ap-dk04.1.patch | 167 ------ 25 files changed, 2442 deletions(-) delete mode 100644 target/linux/ipq40xx/config-5.10 delete mode 100644 target/linux/ipq40xx/patches-5.10/0001-v5.12-ARM-dts-qcom-ipq4019-add-USB-devicetree-nodes.patch delete mode 100644 target/linux/ipq40xx/patches-5.10/0002-v5.12-ARM-dts-qcom-ipq4019-add-more-labels.patch delete mode 100644 target/linux/ipq40xx/patches-5.10/0003-v5.12-ARM-dts-qcom-ipq4019-add-SDHCI-VQMMC-LDO-node.patch delete mode 100644 target/linux/ipq40xx/patches-5.10/104-clk-fix-apss-cpu-overclocking.patch delete mode 100644 target/linux/ipq40xx/patches-5.10/300-clk-qcom-ipq4019-add-ess-reset.patch delete mode 100644 target/linux/ipq40xx/patches-5.10/301-arm-compressed-add-appended-DTB-section.patch delete mode 100644 target/linux/ipq40xx/patches-5.10/302-arm-compressed-set-ipq40xx-watchdog-to-allow-boot.patch delete mode 100644 target/linux/ipq40xx/patches-5.10/400-mmc-sdhci-sdhci-msm-use-sdhci_set_clock-instead-of-s.patch delete mode 100644 target/linux/ipq40xx/patches-5.10/420-firmware-qcom-scm-disable-SDI.patch delete mode 100644 target/linux/ipq40xx/patches-5.10/421-firmware-qcom-scm-cold-boot-address.patch delete mode 100644 target/linux/ipq40xx/patches-5.10/444-mtd-nand-rawnand-add-support-for-Toshiba-TC58NVG0S3H.patch delete mode 100644 target/linux/ipq40xx/patches-5.10/700-skbuff-add-DSA-specific-data-to-struct-skb_shared_in.patch delete mode 100644 target/linux/ipq40xx/patches-5.10/701-net-dsa-tag_ipq4019-add-shinfo-based-tagging-driver-.patch delete mode 100644 target/linux/ipq40xx/patches-5.10/702-net-ethernet-qualcomm-add-IPQESS-support.patch delete mode 100644 target/linux/ipq40xx/patches-5.10/703-arm-dts-ipq4019-add-ethernet-controller-DT-node.patch delete mode 100644 target/linux/ipq40xx/patches-5.10/704-net-phy-define-PSGMII-PHY-interface-mode.patch delete mode 100644 target/linux/ipq40xx/patches-5.10/705-net-dsa-add-Qualcomm-IPQ4019-built-in-switch-support.patch delete mode 100644 target/linux/ipq40xx/patches-5.10/706-arm-dts-ipq4019-add-switch-node.patch delete mode 100644 target/linux/ipq40xx/patches-5.10/707-dt-bindings-net-add-QCA807x-PHY.patch delete mode 100644 target/linux/ipq40xx/patches-5.10/708-net-phy-Add-Qualcom-QCA807x-driver.patch delete mode 100644 target/linux/ipq40xx/patches-5.10/709-arm-dts-ipq4019-QCA807x-properties.patch delete mode 100644 target/linux/ipq40xx/patches-5.10/850-soc-add-qualcomm-syscon.patch delete mode 100644 target/linux/ipq40xx/patches-5.10/900-dts-ipq4019-ap-dk01.1.patch delete mode 100644 target/linux/ipq40xx/patches-5.10/902-dts-ipq4019-ap-dk04.1.patch diff --git a/target/linux/ipq40xx/config-5.10 b/target/linux/ipq40xx/config-5.10 deleted file mode 100644 index 7a0d966aa0..0000000000 --- a/target/linux/ipq40xx/config-5.10 +++ /dev/null @@ -1,500 +0,0 @@ -CONFIG_ALIGNMENT_TRAP=y -# CONFIG_APQ_GCC_8084 is not set -# CONFIG_APQ_MMCC_8084 is not set -CONFIG_ARCH_32BIT_OFF_T=y -CONFIG_ARCH_HIBERNATION_POSSIBLE=y -CONFIG_ARCH_IPQ40XX=y -CONFIG_ARCH_KEEP_MEMBLOCK=y -# CONFIG_ARCH_MDM9615 is not set -CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y -# CONFIG_ARCH_MSM8960 is not set -# CONFIG_ARCH_MSM8974 is not set -# CONFIG_ARCH_MSM8X60 is not set -CONFIG_ARCH_MULTIPLATFORM=y -CONFIG_ARCH_MULTI_V6_V7=y -CONFIG_ARCH_MULTI_V7=y -CONFIG_ARCH_NR_GPIO=0 -CONFIG_ARCH_OPTIONAL_KERNEL_RWX=y -CONFIG_ARCH_OPTIONAL_KERNEL_RWX_DEFAULT=y -CONFIG_ARCH_QCOM=y -CONFIG_ARCH_SELECT_MEMORY_MODEL=y -CONFIG_ARCH_SPARSEMEM_ENABLE=y -CONFIG_ARCH_SUSPEND_POSSIBLE=y -CONFIG_ARM=y -CONFIG_ARM_AMBA=y -CONFIG_ARM_APPENDED_DTB=y -CONFIG_ARM_ARCH_TIMER=y -CONFIG_ARM_ARCH_TIMER_EVTSTREAM=y -# CONFIG_ARM_ATAG_DTB_COMPAT is not set -CONFIG_ARM_CPUIDLE=y -# CONFIG_ARM_CPU_TOPOLOGY is not set -CONFIG_ARM_CRYPTO=y -CONFIG_ARM_GIC=y -CONFIG_ARM_HAS_SG_CHAIN=y -CONFIG_ARM_L1_CACHE_SHIFT=6 -CONFIG_ARM_L1_CACHE_SHIFT_6=y -CONFIG_ARM_PATCH_IDIV=y -CONFIG_ARM_PATCH_PHYS_VIRT=y -# CONFIG_ARM_QCOM_CPUFREQ_HW is not set -# CONFIG_ARM_QCOM_CPUFREQ_NVMEM is not set -# CONFIG_ARM_QCOM_SPM_CPUIDLE is not set -# CONFIG_ARM_SMMU is not set -CONFIG_ARM_THUMB=y -CONFIG_ARM_UNWIND=y -CONFIG_ARM_VIRT_EXT=y -CONFIG_AT803X_PHY=y -CONFIG_AUTO_ZRELADDR=y -CONFIG_BCH=y -CONFIG_BINFMT_FLAT_ARGVP_ENVP_ON_STACK=y -CONFIG_BLK_CMDLINE_PARSER=y -CONFIG_BLK_DEV_LOOP=y -CONFIG_BLK_MQ_PCI=y -CONFIG_BOUNCE=y -# CONFIG_CACHE_L2X0 is not set -CONFIG_CLKDEV_LOOKUP=y -CONFIG_CLKSRC_QCOM=y -CONFIG_CLONE_BACKWARDS=y -CONFIG_CMDLINE_PARTITION=y -CONFIG_COMMON_CLK=y -CONFIG_COMMON_CLK_QCOM=y -CONFIG_COMPAT_32BIT_TIME=y -CONFIG_CPUFREQ_DT=y -CONFIG_CPUFREQ_DT_PLATDEV=y -CONFIG_CPU_32v6K=y -CONFIG_CPU_32v7=y -CONFIG_CPU_ABRT_EV7=y -CONFIG_CPU_CACHE_V7=y -CONFIG_CPU_CACHE_VIPT=y -CONFIG_CPU_COPY_V6=y -CONFIG_CPU_CP15=y -CONFIG_CPU_CP15_MMU=y -CONFIG_CPU_FREQ=y -CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND=y -# CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE is not set -CONFIG_CPU_FREQ_GOV_ATTR_SET=y -CONFIG_CPU_FREQ_GOV_COMMON=y -# CONFIG_CPU_FREQ_GOV_CONSERVATIVE is not set -CONFIG_CPU_FREQ_GOV_ONDEMAND=y -CONFIG_CPU_FREQ_GOV_PERFORMANCE=y -# CONFIG_CPU_FREQ_GOV_POWERSAVE is not set -# CONFIG_CPU_FREQ_GOV_USERSPACE is not set -CONFIG_CPU_FREQ_STAT=y -CONFIG_CPU_HAS_ASID=y -CONFIG_CPU_IDLE=y -CONFIG_CPU_IDLE_GOV_LADDER=y -CONFIG_CPU_IDLE_GOV_MENU=y -CONFIG_CPU_IDLE_MULTIPLE_DRIVERS=y -CONFIG_CPU_PABRT_V7=y -CONFIG_CPU_PM=y -CONFIG_CPU_RMAP=y -CONFIG_CPU_SPECTRE=y -CONFIG_CPU_THERMAL=y -CONFIG_CPU_THUMB_CAPABLE=y -CONFIG_CPU_TLB_V7=y -CONFIG_CPU_V7=y -CONFIG_CRC16=y -# CONFIG_CRC32_SARWATE is not set -CONFIG_CRC32_SLICEBY8=y -CONFIG_CRYPTO_AES_ARM=y -CONFIG_CRYPTO_AES_ARM_BS=y -CONFIG_CRYPTO_BLAKE2S=y -CONFIG_CRYPTO_CBC=y -CONFIG_CRYPTO_CRYPTD=y -CONFIG_CRYPTO_DEFLATE=y -CONFIG_CRYPTO_DES=y -CONFIG_CRYPTO_DEV_QCE=y -# CONFIG_CRYPTO_DEV_QCE_ENABLE_ALL is not set -# CONFIG_CRYPTO_DEV_QCE_ENABLE_SHA is not set -CONFIG_CRYPTO_DEV_QCE_ENABLE_SKCIPHER=y -CONFIG_CRYPTO_DEV_QCE_SKCIPHER=y -CONFIG_CRYPTO_DEV_QCE_SW_MAX_LEN=512 -CONFIG_CRYPTO_DEV_QCOM_RNG=y -CONFIG_CRYPTO_DRBG=y -CONFIG_CRYPTO_DRBG_HMAC=y -CONFIG_CRYPTO_DRBG_MENU=y -CONFIG_CRYPTO_ECB=y -CONFIG_CRYPTO_HASH_INFO=y -CONFIG_CRYPTO_HMAC=y -CONFIG_CRYPTO_HW=y -CONFIG_CRYPTO_JITTERENTROPY=y -CONFIG_CRYPTO_LIB_BLAKE2S_GENERIC=y -CONFIG_CRYPTO_LIB_DES=y -CONFIG_CRYPTO_LIB_SHA256=y -CONFIG_CRYPTO_LZO=y -CONFIG_CRYPTO_RNG=y -CONFIG_CRYPTO_RNG2=y -CONFIG_CRYPTO_RNG_DEFAULT=y -CONFIG_CRYPTO_SEQIV=y -CONFIG_CRYPTO_SHA1=y -CONFIG_CRYPTO_SHA256=y -CONFIG_CRYPTO_SHA256_ARM=y -CONFIG_CRYPTO_SIMD=y -CONFIG_CRYPTO_XTS=y -CONFIG_CRYPTO_ZSTD=y -CONFIG_DCACHE_WORD_ACCESS=y -CONFIG_DEBUG_LL_INCLUDE="mach/debug-macro.S" -CONFIG_DEBUG_MISC=y -CONFIG_DMADEVICES=y -CONFIG_DMA_ENGINE=y -CONFIG_DMA_OF=y -CONFIG_DMA_OPS=y -CONFIG_DMA_REMAP=y -CONFIG_DMA_SHARED_BUFFER=y -CONFIG_DMA_VIRTUAL_CHANNELS=y -CONFIG_DTC=y -CONFIG_DT_IDLE_STATES=y -CONFIG_DYNAMIC_DEBUG=y -CONFIG_EDAC_ATOMIC_SCRUB=y -CONFIG_EDAC_SUPPORT=y -CONFIG_EEPROM_AT24=y -CONFIG_EXTCON=y -CONFIG_FIXED_PHY=y -CONFIG_FIX_EARLYCON_MEM=y -CONFIG_FW_LOADER_PAGED_BUF=y -CONFIG_GENERIC_ALLOCATOR=y -CONFIG_GENERIC_BUG=y -CONFIG_GENERIC_CLOCKEVENTS=y -CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y -CONFIG_GENERIC_CPU_AUTOPROBE=y -CONFIG_GENERIC_EARLY_IOREMAP=y -CONFIG_GENERIC_GETTIMEOFDAY=y -CONFIG_GENERIC_IDLE_POLL_SETUP=y -CONFIG_GENERIC_IRQ_EFFECTIVE_AFF_MASK=y -CONFIG_GENERIC_IRQ_MULTI_HANDLER=y -CONFIG_GENERIC_IRQ_SHOW=y -CONFIG_GENERIC_IRQ_SHOW_LEVEL=y -CONFIG_GENERIC_MSI_IRQ=y -CONFIG_GENERIC_MSI_IRQ_DOMAIN=y -CONFIG_GENERIC_PCI_IOMAP=y -CONFIG_GENERIC_PHY=y -CONFIG_GENERIC_PINCONF=y -CONFIG_GENERIC_PINCTRL_GROUPS=y -CONFIG_GENERIC_PINMUX_FUNCTIONS=y -CONFIG_GENERIC_SCHED_CLOCK=y -CONFIG_GENERIC_SMP_IDLE_THREAD=y -CONFIG_GENERIC_STRNCPY_FROM_USER=y -CONFIG_GENERIC_STRNLEN_USER=y -CONFIG_GENERIC_TIME_VSYSCALL=y -CONFIG_GENERIC_VDSO_32=y -CONFIG_GPIOLIB_IRQCHIP=y -CONFIG_GPIO_74X164=y -CONFIG_GPIO_WATCHDOG=y -CONFIG_GPIO_WATCHDOG_ARCH_INITCALL=y -CONFIG_GRO_CELLS=y -CONFIG_HANDLE_DOMAIN_IRQ=y -CONFIG_HARDEN_BRANCH_PREDICTOR=y -CONFIG_HARDIRQS_SW_RESEND=y -CONFIG_HAS_DMA=y -CONFIG_HAS_IOMEM=y -CONFIG_HAS_IOPORT_MAP=y -CONFIG_HAVE_SMP=y -CONFIG_HIGHMEM=y -CONFIG_HIGHPTE=y -CONFIG_HWSPINLOCK=y -CONFIG_HWSPINLOCK_QCOM=y -CONFIG_HW_RANDOM=y -CONFIG_HW_RANDOM_OPTEE=y -CONFIG_HZ_FIXED=0 -CONFIG_I2C=y -CONFIG_I2C_BOARDINFO=y -CONFIG_I2C_CHARDEV=y -CONFIG_I2C_HELPER_AUTO=y -# CONFIG_I2C_QCOM_CCI is not set -CONFIG_I2C_QUP=y -CONFIG_INITRAMFS_SOURCE="" -# CONFIG_IOMMU_DEBUGFS is not set -# CONFIG_IOMMU_IO_PGTABLE_ARMV7S is not set -# CONFIG_IOMMU_IO_PGTABLE_LPAE is not set -CONFIG_IOMMU_SUPPORT=y -CONFIG_IO_URING=y -# CONFIG_IPQ_APSS_PLL is not set -CONFIG_IPQ_GCC_4019=y -# CONFIG_IPQ_GCC_6018 is not set -# CONFIG_IPQ_GCC_806X is not set -# CONFIG_IPQ_GCC_8074 is not set -# CONFIG_IPQ_LCC_806X is not set -CONFIG_IRQCHIP=y -CONFIG_IRQ_DOMAIN=y -CONFIG_IRQ_DOMAIN_HIERARCHY=y -CONFIG_IRQ_FASTEOI_HIERARCHY_HANDLERS=y -CONFIG_IRQ_FORCED_THREADING=y -CONFIG_IRQ_WORK=y -# CONFIG_KPSS_XCC is not set -# CONFIG_KRAITCC is not set -CONFIG_LEDS_LP5523=y -CONFIG_LEDS_LP5562=y -CONFIG_LEDS_LP55XX_COMMON=y -CONFIG_LEDS_TLC591XX=y -CONFIG_LED_TRIGGER_PHY=y -CONFIG_LIBFDT=y -CONFIG_LOCK_DEBUGGING_SUPPORT=y -CONFIG_LOCK_SPIN_ON_OWNER=y -CONFIG_LZO_COMPRESS=y -CONFIG_LZO_DECOMPRESS=y -CONFIG_MDIO_BITBANG=y -CONFIG_MDIO_BUS=y -CONFIG_MDIO_DEVICE=y -CONFIG_MDIO_DEVRES=y -CONFIG_MDIO_GPIO=y -CONFIG_MDIO_IPQ4019=y -# CONFIG_MDM_GCC_9615 is not set -# CONFIG_MDM_LCC_9615 is not set -CONFIG_MEMFD_CREATE=y -# CONFIG_MFD_HI6421_SPMI is not set -# CONFIG_MFD_QCOM_RPM is not set -# CONFIG_MFD_SPMI_PMIC is not set -CONFIG_MFD_SYSCON=y -CONFIG_MIGHT_HAVE_CACHE_L2X0=y -CONFIG_MIGRATION=y -CONFIG_MMC=y -CONFIG_MMC_BLOCK=y -CONFIG_MMC_CQHCI=y -CONFIG_MMC_SDHCI=y -CONFIG_MMC_SDHCI_IO_ACCESSORS=y -CONFIG_MMC_SDHCI_MSM=y -# CONFIG_MMC_SDHCI_PCI is not set -CONFIG_MMC_SDHCI_PLTFM=y -CONFIG_MODULES_USE_ELF_REL=y -# CONFIG_MSM_GCC_8660 is not set -# CONFIG_MSM_GCC_8916 is not set -# CONFIG_MSM_GCC_8939 is not set -# CONFIG_MSM_GCC_8960 is not set -# CONFIG_MSM_GCC_8974 is not set -# CONFIG_MSM_GCC_8994 is not set -# CONFIG_MSM_GCC_8996 is not set -# CONFIG_MSM_GCC_8998 is not set -# CONFIG_MSM_GPUCC_8998 is not set -# CONFIG_MSM_LCC_8960 is not set -# CONFIG_MSM_MMCC_8960 is not set -# CONFIG_MSM_MMCC_8974 is not set -# CONFIG_MSM_MMCC_8996 is not set -# CONFIG_MSM_MMCC_8998 is not set -CONFIG_MTD_CMDLINE_PARTS=y -CONFIG_MTD_NAND_CORE=y -CONFIG_MTD_NAND_ECC=y -CONFIG_MTD_NAND_ECC_SW_BCH=y -CONFIG_MTD_NAND_ECC_SW_HAMMING=y -CONFIG_MTD_NAND_QCOM=y -CONFIG_MTD_RAW_NAND=y -CONFIG_MTD_SPI_NAND=y -CONFIG_MTD_SPI_NOR=y -CONFIG_MTD_SPLIT_FIRMWARE=y -CONFIG_MTD_SPLIT_FIT_FW=y -CONFIG_MTD_SPLIT_WRGG_FW=y -CONFIG_MTD_UBI=y -CONFIG_MTD_UBI_BEB_LIMIT=20 -CONFIG_MTD_UBI_BLOCK=y -CONFIG_MTD_UBI_WL_THRESHOLD=4096 -CONFIG_MUTEX_SPIN_ON_OWNER=y -CONFIG_NEED_DMA_MAP_STATE=y -CONFIG_NEON=y -CONFIG_NET_DEVLINK=y -CONFIG_NET_DSA=y -CONFIG_NET_DSA_QCA8K_IPQ4019=y -CONFIG_NET_DSA_TAG_IPQ4019=y -CONFIG_NET_FLOW_LIMIT=y -CONFIG_NET_PTP_CLASSIFY=y -CONFIG_NET_SWITCHDEV=y -CONFIG_NLS=y -CONFIG_NO_HZ=y -CONFIG_NO_HZ_COMMON=y -CONFIG_NO_HZ_IDLE=y -CONFIG_NR_CPUS=4 -CONFIG_NVMEM=y -# CONFIG_NVMEM_SPMI_SDAM is not set -CONFIG_NVMEM_SYSFS=y -CONFIG_OF=y -CONFIG_OF_ADDRESS=y -CONFIG_OF_EARLY_FLATTREE=y -CONFIG_OF_FLATTREE=y -CONFIG_OF_GPIO=y -CONFIG_OF_IRQ=y -CONFIG_OF_KOBJ=y -CONFIG_OF_MDIO=y -CONFIG_OF_NET=y -CONFIG_OLD_SIGACTION=y -CONFIG_OLD_SIGSUSPEND3=y -CONFIG_OPTEE=y -CONFIG_OPTEE_SHM_NUM_PRIV_PAGES=1 -CONFIG_PADATA=y -CONFIG_PAGE_OFFSET=0xC0000000 -CONFIG_PCI=y -CONFIG_PCIEAER=y -CONFIG_PCIEPORTBUS=y -CONFIG_PCIE_DW=y -CONFIG_PCIE_DW_HOST=y -CONFIG_PCIE_QCOM=y -CONFIG_PCI_DISABLE_COMMON_QUIRKS=y -CONFIG_PCI_DOMAINS=y -CONFIG_PCI_DOMAINS_GENERIC=y -CONFIG_PCI_MSI=y -CONFIG_PCI_MSI_IRQ_DOMAIN=y -CONFIG_PERF_USE_VMALLOC=y -CONFIG_PGTABLE_LEVELS=2 -CONFIG_PHYLIB=y -CONFIG_PHYLINK=y -# CONFIG_PHY_QCOM_APQ8064_SATA is not set -CONFIG_PHY_QCOM_IPQ4019_USB=y -# CONFIG_PHY_QCOM_IPQ806X_SATA is not set -# CONFIG_PHY_QCOM_IPQ806X_USB is not set -# CONFIG_PHY_QCOM_PCIE2 is not set -# CONFIG_PHY_QCOM_QMP is not set -# CONFIG_PHY_QCOM_QUSB2 is not set -# CONFIG_PHY_QCOM_USB_HS_28NM is not set -# CONFIG_PHY_QCOM_USB_SNPS_FEMTO_V2 is not set -# CONFIG_PHY_QCOM_USB_SS is not set -CONFIG_PINCTRL=y -# CONFIG_PINCTRL_APQ8064 is not set -# CONFIG_PINCTRL_APQ8084 is not set -CONFIG_PINCTRL_IPQ4019=y -# CONFIG_PINCTRL_IPQ6018 is not set -# CONFIG_PINCTRL_IPQ8064 is not set -# CONFIG_PINCTRL_IPQ8074 is not set -# CONFIG_PINCTRL_MDM9615 is not set -CONFIG_PINCTRL_MSM=y -# CONFIG_PINCTRL_MSM8226 is not set -# CONFIG_PINCTRL_MSM8660 is not set -# CONFIG_PINCTRL_MSM8916 is not set -# CONFIG_PINCTRL_MSM8960 is not set -# CONFIG_PINCTRL_MSM8976 is not set -# CONFIG_PINCTRL_MSM8994 is not set -# CONFIG_PINCTRL_MSM8996 is not set -# CONFIG_PINCTRL_MSM8998 is not set -# CONFIG_PINCTRL_QCOM_SPMI_PMIC is not set -# CONFIG_PINCTRL_QCOM_SSBI_PMIC is not set -# CONFIG_PINCTRL_QCS404 is not set -# CONFIG_PINCTRL_SC7180 is not set -# CONFIG_PINCTRL_SDM660 is not set -# CONFIG_PINCTRL_SDM845 is not set -# CONFIG_PINCTRL_SM8150 is not set -# CONFIG_PINCTRL_SM8250 is not set -CONFIG_PM_OPP=y -CONFIG_POWER_RESET=y -CONFIG_POWER_RESET_MSM=y -CONFIG_POWER_RESET_GPIO_RESTART=y -CONFIG_POWER_SUPPLY=y -CONFIG_PPS=y -CONFIG_PRINTK_TIME=y -CONFIG_PTP_1588_CLOCK=y -CONFIG_QCA807X_PHY=y -CONFIG_QCOM_A53PLL=y -CONFIG_QCOM_BAM_DMA=y -# CONFIG_QCOM_COMMAND_DB is not set -# CONFIG_QCOM_CPR is not set -# CONFIG_QCOM_EBI2 is not set -# CONFIG_QCOM_GENI_SE is not set -# CONFIG_QCOM_GSBI is not set -# CONFIG_QCOM_HFPLL is not set -# CONFIG_QCOM_IOMMU is not set -CONFIG_QCOM_IPQ4019_ESS_EDMA=y -# CONFIG_QCOM_LLCC is not set -# CONFIG_QCOM_OCMEM is not set -# CONFIG_QCOM_PDC is not set -CONFIG_QCOM_QFPROM=y -# CONFIG_QCOM_RMTFS_MEM is not set -# CONFIG_QCOM_RPMH is not set -CONFIG_QCOM_SCM=y -# CONFIG_QCOM_SCM_DOWNLOAD_MODE_DEFAULT is not set -CONFIG_QCOM_SMEM=y -# CONFIG_QCOM_SMSM is not set -# CONFIG_QCOM_SOCINFO is not set -CONFIG_QCOM_TCSR=y -# CONFIG_QCOM_TSENS is not set -CONFIG_QCOM_WDT=y -# CONFIG_QCS_GCC_404 is not set -# CONFIG_QCS_Q6SSTOP_404 is not set -# CONFIG_QCS_TURING_404 is not set -CONFIG_RAS=y -CONFIG_RATIONAL=y -CONFIG_REGMAP=y -CONFIG_REGMAP_I2C=y -CONFIG_REGMAP_MMIO=y -CONFIG_REGULATOR=y -CONFIG_REGULATOR_FIXED_VOLTAGE=y -# CONFIG_REGULATOR_QCOM_LABIBB is not set -# CONFIG_REGULATOR_QCOM_SPMI is not set -# CONFIG_REGULATOR_QCOM_USB_VBUS is not set -CONFIG_REGULATOR_VCTRL=y -CONFIG_REGULATOR_VQMMC_IPQ4019=y -CONFIG_RESET_CONTROLLER=y -# CONFIG_RESET_QCOM_AOSS is not set -# CONFIG_RESET_QCOM_PDC is not set -CONFIG_RFS_ACCEL=y -CONFIG_RPS=y -CONFIG_RTC_CLASS=y -CONFIG_RTC_I2C_AND_SPI=y -CONFIG_RTC_MC146818_LIB=y -CONFIG_RWSEM_SPIN_ON_OWNER=y -# CONFIG_SC_DISPCC_7180 is not set -# CONFIG_SC_GCC_7180 is not set -# CONFIG_SC_GPUCC_7180 is not set -# CONFIG_SC_LPASS_CORECC_7180 is not set -# CONFIG_SC_MSS_7180 is not set -# CONFIG_SC_VIDEOCC_7180 is not set -# CONFIG_SDM_CAMCC_845 is not set -# CONFIG_SDM_DISPCC_845 is not set -# CONFIG_SDM_GCC_660 is not set -# CONFIG_SDM_GCC_845 is not set -# CONFIG_SDM_GPUCC_845 is not set -# CONFIG_SDM_LPASSCC_845 is not set -# CONFIG_SDM_VIDEOCC_845 is not set -CONFIG_SERIAL_8250_FSL=y -CONFIG_SERIAL_MCTRL_GPIO=y -CONFIG_SERIAL_MSM=y -CONFIG_SERIAL_MSM_CONSOLE=y -CONFIG_SGL_ALLOC=y -CONFIG_SMP=y -CONFIG_SMP_ON_UP=y -# CONFIG_SM_GCC_8150 is not set -# CONFIG_SM_GCC_8250 is not set -# CONFIG_SM_GPUCC_8150 is not set -# CONFIG_SM_GPUCC_8250 is not set -# CONFIG_SM_VIDEOCC_8150 is not set -# CONFIG_SM_VIDEOCC_8250 is not set -CONFIG_SPARSE_IRQ=y -CONFIG_SPI=y -CONFIG_SPI_BITBANG=y -CONFIG_SPI_GPIO=y -CONFIG_SPI_MASTER=y -CONFIG_SPI_MEM=y -CONFIG_SPI_QUP=y -CONFIG_SPMI=y -# CONFIG_SPMI_HISI3670 is not set -CONFIG_SPMI_MSM_PMIC_ARB=y -# CONFIG_SPMI_PMIC_CLKDIV is not set -CONFIG_SRCU=y -CONFIG_SWPHY=y -CONFIG_SWP_EMULATE=y -CONFIG_SYS_SUPPORTS_APM_EMULATION=y -CONFIG_TEE=y -CONFIG_THERMAL=y -CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y -CONFIG_THERMAL_EMERGENCY_POWEROFF_DELAY_MS=0 -CONFIG_THERMAL_GOV_STEP_WISE=y -CONFIG_THERMAL_OF=y -CONFIG_TICK_CPU_ACCOUNTING=y -CONFIG_TIMER_OF=y -CONFIG_TIMER_PROBE=y -CONFIG_TREE_RCU=y -CONFIG_TREE_SRCU=y -CONFIG_UBIFS_FS=y -CONFIG_UEVENT_HELPER_PATH="" -CONFIG_UNCOMPRESS_INCLUDE="debug/uncompress.h" -CONFIG_UNWINDER_ARM=y -CONFIG_USB=y -CONFIG_USB_COMMON=y -CONFIG_USB_SUPPORT=y -CONFIG_USE_OF=y -CONFIG_VFP=y -CONFIG_VFPv3=y -CONFIG_WATCHDOG_CORE=y -CONFIG_XPS=y -CONFIG_XXHASH=y -CONFIG_XZ_DEC_ARM=y -CONFIG_XZ_DEC_BCJ=y -CONFIG_ZBOOT_ROM_BSS=0 -CONFIG_ZBOOT_ROM_TEXT=0 -CONFIG_ZLIB_DEFLATE=y -CONFIG_ZLIB_INFLATE=y -CONFIG_ZSTD_COMPRESS=y -CONFIG_ZSTD_DECOMPRESS=y diff --git a/target/linux/ipq40xx/patches-5.10/0001-v5.12-ARM-dts-qcom-ipq4019-add-USB-devicetree-nodes.patch b/target/linux/ipq40xx/patches-5.10/0001-v5.12-ARM-dts-qcom-ipq4019-add-USB-devicetree-nodes.patch deleted file mode 100644 index 5ebed88bb3..0000000000 --- a/target/linux/ipq40xx/patches-5.10/0001-v5.12-ARM-dts-qcom-ipq4019-add-USB-devicetree-nodes.patch +++ /dev/null @@ -1,99 +0,0 @@ -From b8afc254b40167fd37b4d4263e750dab1f9ef157 Mon Sep 17 00:00:00 2001 -From: John Crispin -Date: Wed, 9 Sep 2020 18:38:31 +0200 -Subject: [PATCH] ARM: dts: qcom: ipq4019: add USB devicetree nodes - -Since we now have driver for the USB PHY, and USB controller is already supported by the DWC3 driver lets add the necessary nodes to DTSI. - -Signed-off-by: John Crispin -Signed-off-by: Robert Marko -Cc: Luka Perkov -Reviewed-by: Vinod Koul -Link: https://lore.kernel.org/r/20200909163831.1894142-1-robert.marko@sartura.hr -Signed-off-by: Bjorn Andersson ---- - arch/arm/boot/dts/qcom-ipq4019.dtsi | 74 +++++++++++++++++++++++++++++ - 1 file changed, 74 insertions(+) - ---- a/arch/arm/boot/dts/qcom-ipq4019.dtsi -+++ b/arch/arm/boot/dts/qcom-ipq4019.dtsi -@@ -606,5 +606,79 @@ - reg = <4>; - }; - }; -+ -+ usb3_ss_phy: ssphy@9a000 { -+ compatible = "qcom,usb-ss-ipq4019-phy"; -+ #phy-cells = <0>; -+ reg = <0x9a000 0x800>; -+ reg-names = "phy_base"; -+ resets = <&gcc USB3_UNIPHY_PHY_ARES>; -+ reset-names = "por_rst"; -+ status = "disabled"; -+ }; -+ -+ usb3_hs_phy: hsphy@a6000 { -+ compatible = "qcom,usb-hs-ipq4019-phy"; -+ #phy-cells = <0>; -+ reg = <0xa6000 0x40>; -+ reg-names = "phy_base"; -+ resets = <&gcc USB3_HSPHY_POR_ARES>, <&gcc USB3_HSPHY_S_ARES>; -+ reset-names = "por_rst", "srif_rst"; -+ status = "disabled"; -+ }; -+ -+ usb3: usb3@8af8800 { -+ compatible = "qcom,dwc3"; -+ reg = <0x8af8800 0x100>; -+ #address-cells = <1>; -+ #size-cells = <1>; -+ clocks = <&gcc GCC_USB3_MASTER_CLK>, -+ <&gcc GCC_USB3_SLEEP_CLK>, -+ <&gcc GCC_USB3_MOCK_UTMI_CLK>; -+ clock-names = "master", "sleep", "mock_utmi"; -+ ranges; -+ status = "disabled"; -+ -+ dwc3@8a00000 { -+ compatible = "snps,dwc3"; -+ reg = <0x8a00000 0xf8000>; -+ interrupts = ; -+ phys = <&usb3_hs_phy>, <&usb3_ss_phy>; -+ phy-names = "usb2-phy", "usb3-phy"; -+ dr_mode = "host"; -+ }; -+ }; -+ -+ usb2_hs_phy: hsphy@a8000 { -+ compatible = "qcom,usb-hs-ipq4019-phy"; -+ #phy-cells = <0>; -+ reg = <0xa8000 0x40>; -+ reg-names = "phy_base"; -+ resets = <&gcc USB2_HSPHY_POR_ARES>, <&gcc USB2_HSPHY_S_ARES>; -+ reset-names = "por_rst", "srif_rst"; -+ status = "disabled"; -+ }; -+ -+ usb2: usb2@60f8800 { -+ compatible = "qcom,dwc3"; -+ reg = <0x60f8800 0x100>; -+ #address-cells = <1>; -+ #size-cells = <1>; -+ clocks = <&gcc GCC_USB2_MASTER_CLK>, -+ <&gcc GCC_USB2_SLEEP_CLK>, -+ <&gcc GCC_USB2_MOCK_UTMI_CLK>; -+ clock-names = "master", "sleep", "mock_utmi"; -+ ranges; -+ status = "disabled"; -+ -+ dwc3@6000000 { -+ compatible = "snps,dwc3"; -+ reg = <0x6000000 0xf8000>; -+ interrupts = ; -+ phys = <&usb2_hs_phy>; -+ phy-names = "usb2-phy"; -+ dr_mode = "host"; -+ }; -+ }; - }; - }; diff --git a/target/linux/ipq40xx/patches-5.10/0002-v5.12-ARM-dts-qcom-ipq4019-add-more-labels.patch b/target/linux/ipq40xx/patches-5.10/0002-v5.12-ARM-dts-qcom-ipq4019-add-more-labels.patch deleted file mode 100644 index d7af2bb7b1..0000000000 --- a/target/linux/ipq40xx/patches-5.10/0002-v5.12-ARM-dts-qcom-ipq4019-add-more-labels.patch +++ /dev/null @@ -1,44 +0,0 @@ -From d1ae4c808e7802008225078d93fbadd4aeea1e2d Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Wed, 9 Sep 2020 21:56:37 +0200 -Subject: [PATCH] ARM: dts: qcom: ipq4019: add more labels - -Lets add labels to more commonly used nodes for easier modification in board DTS files. - -Signed-off-by: Robert Marko -Cc: Luka Perkov -Link: https://lore.kernel.org/r/20200909195640.3127341-2-robert.marko@sartura.hr -Signed-off-by: Bjorn Andersson ---- - arch/arm/boot/dts/qcom-ipq4019.dtsi | 6 +++--- - 1 file changed, 3 insertions(+), 3 deletions(-) - ---- a/arch/arm/boot/dts/qcom-ipq4019.dtsi -+++ b/arch/arm/boot/dts/qcom-ipq4019.dtsi -@@ -191,7 +191,7 @@ - reg = <0x1800000 0x60000>; - }; - -- rng@22000 { -+ prng: rng@22000 { - compatible = "qcom,prng"; - reg = <0x22000 0x140>; - clocks = <&gcc GCC_PRNG_AHB_CLK>; -@@ -301,7 +301,7 @@ - status = "disabled"; - }; - -- crypto@8e3a000 { -+ crypto: crypto@8e3a000 { - compatible = "qcom,crypto-v5.1"; - reg = <0x08e3a000 0x6000>; - clocks = <&gcc GCC_CRYPTO_AHB_CLK>, -@@ -387,7 +387,7 @@ - dma-names = "rx", "tx"; - }; - -- watchdog@b017000 { -+ watchdog: watchdog@b017000 { - compatible = "qcom,kpss-wdt", "qcom,kpss-wdt-ipq4019"; - reg = <0xb017000 0x40>; - clocks = <&sleep_clk>; diff --git a/target/linux/ipq40xx/patches-5.10/0003-v5.12-ARM-dts-qcom-ipq4019-add-SDHCI-VQMMC-LDO-node.patch b/target/linux/ipq40xx/patches-5.10/0003-v5.12-ARM-dts-qcom-ipq4019-add-SDHCI-VQMMC-LDO-node.patch deleted file mode 100644 index ff3fdc5407..0000000000 --- a/target/linux/ipq40xx/patches-5.10/0003-v5.12-ARM-dts-qcom-ipq4019-add-SDHCI-VQMMC-LDO-node.patch +++ /dev/null @@ -1,35 +0,0 @@ -From e14775aa2feac18e7378cb8009b55c13d4236b50 Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Mon, 7 Sep 2020 12:19:37 +0200 -Subject: [PATCH] ARM: dts: qcom: ipq4019: add SDHCI VQMMC LDO node - -Since we now have driver for the SDHCI VQMMC LDO needed -for I/0 voltage levels lets introduce the necessary node for it. - -Signed-off-by: Robert Marko -Cc: Luka Perkov -Link: https://lore.kernel.org/r/20200907101937.10155-1-robert.marko@sartura.hr -Signed-off-by: Bjorn Andersson ---- - arch/arm/boot/dts/qcom-ipq4019.dtsi | 10 ++++++++++ - 1 file changed, 10 insertions(+) - ---- a/arch/arm/boot/dts/qcom-ipq4019.dtsi -+++ b/arch/arm/boot/dts/qcom-ipq4019.dtsi -@@ -210,6 +210,16 @@ - interrupts = ; - }; - -+ vqmmc: regulator@1948000 { -+ compatible = "qcom,vqmmc-ipq4019-regulator"; -+ reg = <0x01948000 0x4>; -+ regulator-name = "vqmmc"; -+ regulator-min-microvolt = <1500000>; -+ regulator-max-microvolt = <3000000>; -+ regulator-always-on; -+ status = "disabled"; -+ }; -+ - sdhci: sdhci@7824900 { - compatible = "qcom,sdhci-msm-v4"; - reg = <0x7824900 0x11c>, <0x7824000 0x800>; diff --git a/target/linux/ipq40xx/patches-5.10/104-clk-fix-apss-cpu-overclocking.patch b/target/linux/ipq40xx/patches-5.10/104-clk-fix-apss-cpu-overclocking.patch deleted file mode 100644 index 25a2020bd2..0000000000 --- a/target/linux/ipq40xx/patches-5.10/104-clk-fix-apss-cpu-overclocking.patch +++ /dev/null @@ -1,115 +0,0 @@ -From f2b87dc1028b710ec8ce25808b9d21f92b376184 Mon Sep 17 00:00:00 2001 -From: Christian Lamparter -Date: Sun, 11 Mar 2018 14:41:31 +0100 -Subject: [PATCH 2/2] clk: fix apss cpu overclocking - -There's an interaction issue between the clk changes:" -clk: qcom: ipq4019: Add the apss cpu pll divider clock node -clk: qcom: ipq4019: remove fixed clocks and add pll clocks -" and the cpufreq-dt. - -cpufreq-dt is now spamming the kernel-log with the following: - -[ 1099.190658] cpu cpu0: dev_pm_opp_set_rate: failed to find current OPP -for freq 761142857 (-34) - -This only happens on certain devices like the Compex WPJ428 -and AVM FritzBox!4040. However, other devices like the Asus -RT-AC58U and Meraki MR33 work just fine. - -The issue stem from the fact that all higher CPU-Clocks -are achieved by switching the clock-parent to the P_DDRPLLAPSS -(ddrpllapss). Which is set by Qualcomm's proprietary bootcode -as part of the DDR calibration. - -For example, the FB4040 uses 256 MiB Nanya NT5CC128M16IP clocked -at round 533 MHz (ddrpllsdcc = 190285714 Hz). - -whereas the 128 MiB Nanya NT5CC64M16GP-DI in the ASUS RT-AC58U is -clocked at a slightly higher 537 MHz ( ddrpllsdcc = 192000000 Hz). - -This patch attempts to fix the issue by modifying -clk_cpu_div_round_rate(), clk_cpu_div_set_rate(), clk_cpu_div_recalc_rate() -to use a new qcom_find_freq_close() function, which returns the closest -matching frequency, instead of the next higher. This way, the SoC in -the FB4040 (with its max clock speed of 710.4 MHz) will no longer -try to overclock to 761 MHz. - -Fixes: d83dcacea18 ("clk: qcom: ipq4019: Add the apss cpu pll divider clock node") -Signed-off-by: Christian Lamparter -Signed-off-by: John Crispin ---- - drivers/clk/qcom/gcc-ipq4019.c | 34 +++++++++++++++++++++++++++++++--- - 1 file changed, 31 insertions(+), 3 deletions(-) - ---- a/drivers/clk/qcom/gcc-ipq4019.c -+++ b/drivers/clk/qcom/gcc-ipq4019.c -@@ -1243,6 +1243,29 @@ static const struct clk_fepll_vco gcc_fe - .reg = 0x2f020, - }; - -+ -+const struct freq_tbl *qcom_find_freq_close(const struct freq_tbl *f, -+ unsigned long rate) -+{ -+ const struct freq_tbl *last = NULL; -+ -+ for ( ; f->freq; f++) { -+ if (rate == f->freq) -+ return f; -+ -+ if (f->freq > rate) { -+ if (!last || -+ (f->freq - rate) < (rate - last->freq)) -+ return f; -+ else -+ return last; -+ } -+ last = f; -+ } -+ -+ return last; -+} -+ - /* - * Round rate function for APSS CPU PLL Clock divider. - * It looks up the frequency table and returns the next higher frequency -@@ -1255,7 +1278,7 @@ static long clk_cpu_div_round_rate(struc - struct clk_hw *p_hw; - const struct freq_tbl *f; - -- f = qcom_find_freq(pll->freq_tbl, rate); -+ f = qcom_find_freq_close(pll->freq_tbl, rate); - if (!f) - return -EINVAL; - -@@ -1278,7 +1301,7 @@ static int clk_cpu_div_set_rate(struct c - u32 mask; - int ret; - -- f = qcom_find_freq(pll->freq_tbl, rate); -+ f = qcom_find_freq_close(pll->freq_tbl, rate); - if (!f) - return -EINVAL; - -@@ -1305,6 +1328,7 @@ static unsigned long - clk_cpu_div_recalc_rate(struct clk_hw *hw, - unsigned long parent_rate) - { -+ const struct freq_tbl *f; - struct clk_fepll *pll = to_clk_fepll(hw); - u32 cdiv, pre_div; - u64 rate; -@@ -1325,7 +1349,11 @@ clk_cpu_div_recalc_rate(struct clk_hw *h - rate = clk_fepll_vco_calc_rate(pll, parent_rate) * 2; - do_div(rate, pre_div); - -- return rate; -+ f = qcom_find_freq_close(pll->freq_tbl, rate); -+ if (!f) -+ return rate; -+ -+ return f->freq; - }; - - static const struct clk_ops clk_regmap_cpu_div_ops = { diff --git a/target/linux/ipq40xx/patches-5.10/300-clk-qcom-ipq4019-add-ess-reset.patch b/target/linux/ipq40xx/patches-5.10/300-clk-qcom-ipq4019-add-ess-reset.patch deleted file mode 100644 index 4297f32e05..0000000000 --- a/target/linux/ipq40xx/patches-5.10/300-clk-qcom-ipq4019-add-ess-reset.patch +++ /dev/null @@ -1,52 +0,0 @@ -From 480c1f7648fc586db12d6003c717c23667a4fcf0 Mon Sep 17 00:00:00 2001 -From: Ram Chandra Jangir -Date: Tue, 28 Mar 2017 22:35:33 +0530 -Subject: [PATCH] clk: qcom: ipq4019: add ess reset - -Added the ESS reset in IPQ4019 GCC. - -Signed-off-by: Ram Chandra Jangir ---- - drivers/clk/qcom/gcc-ipq4019.c | 11 +++++++++++ - include/dt-bindings/clock/qcom,gcc-ipq4019.h | 11 +++++++++++ - 2 files changed, 22 insertions(+) - ---- a/drivers/clk/qcom/gcc-ipq4019.c -+++ b/drivers/clk/qcom/gcc-ipq4019.c -@@ -1736,6 +1736,17 @@ static const struct qcom_reset_map gcc_i - [GCC_TCSR_BCR] = {0x22000, 0}, - [GCC_MPM_BCR] = {0x24000, 0}, - [GCC_SPDM_BCR] = {0x25000, 0}, -+ [ESS_MAC1_ARES] = {0x1200C, 0}, -+ [ESS_MAC2_ARES] = {0x1200C, 1}, -+ [ESS_MAC3_ARES] = {0x1200C, 2}, -+ [ESS_MAC4_ARES] = {0x1200C, 3}, -+ [ESS_MAC5_ARES] = {0x1200C, 4}, -+ [ESS_PSGMII_ARES] = {0x1200C, 5}, -+ [ESS_MAC1_CLK_DIS] = {0x1200C, 8}, -+ [ESS_MAC2_CLK_DIS] = {0x1200C, 9}, -+ [ESS_MAC3_CLK_DIS] = {0x1200C, 10}, -+ [ESS_MAC4_CLK_DIS] = {0x1200C, 11}, -+ [ESS_MAC5_CLK_DIS] = {0x1200C, 12}, - }; - - static const struct regmap_config gcc_ipq4019_regmap_config = { ---- a/include/dt-bindings/clock/qcom,gcc-ipq4019.h -+++ b/include/dt-bindings/clock/qcom,gcc-ipq4019.h -@@ -165,5 +165,16 @@ - #define GCC_QDSS_BCR 69 - #define GCC_MPM_BCR 70 - #define GCC_SPDM_BCR 71 -+#define ESS_MAC1_ARES 72 -+#define ESS_MAC2_ARES 73 -+#define ESS_MAC3_ARES 74 -+#define ESS_MAC4_ARES 75 -+#define ESS_MAC5_ARES 76 -+#define ESS_PSGMII_ARES 77 -+#define ESS_MAC1_CLK_DIS 78 -+#define ESS_MAC2_CLK_DIS 79 -+#define ESS_MAC3_CLK_DIS 80 -+#define ESS_MAC4_CLK_DIS 81 -+#define ESS_MAC5_CLK_DIS 82 - - #endif diff --git a/target/linux/ipq40xx/patches-5.10/301-arm-compressed-add-appended-DTB-section.patch b/target/linux/ipq40xx/patches-5.10/301-arm-compressed-add-appended-DTB-section.patch deleted file mode 100644 index 99e33632c4..0000000000 --- a/target/linux/ipq40xx/patches-5.10/301-arm-compressed-add-appended-DTB-section.patch +++ /dev/null @@ -1,48 +0,0 @@ -From 0843a61d6913bdac8889eb048ed89f7903059787 Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Fri, 30 Oct 2020 13:36:31 +0100 -Subject: [PATCH] arm: compressed: add appended DTB section - -This adds a appended_dtb section to the ARM decompressor -linker script. - -This allows using the existing ARM zImage appended DTB support for -appending a DTB to the raw ELF kernel. - -Its size is set to 1MB max to match the zImage appended DTB size limit. - -To use it to pass the DTB to the kernel, objcopy is used: - -objcopy --set-section-flags=.appended_dtb=alloc,contents \ - --update-section=.appended_dtb=.dtb vmlinux - -This is based off the following patch: -https://github.com/openwrt/openwrt/commit/c063e27e02a9dcac0e7f5877fb154e58fa3e1a69 - -Signed-off-by: Robert Marko ---- - arch/arm/boot/compressed/vmlinux.lds.S | 9 ++++++++- - 1 file changed, 8 insertions(+), 1 deletion(-) - ---- a/arch/arm/boot/compressed/vmlinux.lds.S -+++ b/arch/arm/boot/compressed/vmlinux.lds.S -@@ -101,6 +101,13 @@ SECTIONS - - _edata = .; - -+ .appended_dtb : { -+ /* leave space for appended DTB */ -+ . += 0x100000; -+ } -+ -+ _edata_dtb = .; -+ - /* - * The image_end section appears after any additional loadable sections - * that the linker may decide to insert in the binary image. Having -@@ -138,4 +145,4 @@ SECTIONS - - ARM_ASSERTS - } --ASSERT(_edata_real == _edata, "error: zImage file size is incorrect"); -+ASSERT(_edata_real == _edata_dtb, "error: zImage file size is incorrect"); diff --git a/target/linux/ipq40xx/patches-5.10/302-arm-compressed-set-ipq40xx-watchdog-to-allow-boot.patch b/target/linux/ipq40xx/patches-5.10/302-arm-compressed-set-ipq40xx-watchdog-to-allow-boot.patch deleted file mode 100644 index 1aa5a9f386..0000000000 --- a/target/linux/ipq40xx/patches-5.10/302-arm-compressed-set-ipq40xx-watchdog-to-allow-boot.patch +++ /dev/null @@ -1,66 +0,0 @@ -From 11d6a6128a5a07c429941afc202b6e62a19771be Mon Sep 17 00:00:00 2001 -From: John Thomson -Date: Fri, 23 Oct 2020 19:42:36 +1000 -Subject: [PATCH 2/2] arm: compressed: set ipq40xx watchdog to allow boot - -For IPQ40XX systems where the SoC watchdog is activated before linux, -the watchdog timer may be too small for linux to finish uncompress, -boot, and watchdog management start. -If the watchdog is enabled, set the timeout for it to 30 seconds. -The functionality and offsets were copied from: -drivers/watchdog/qcom-wdt.c qcom_wdt_set_timeout & qcom_wdt_start -The watchdog memory address was taken from: -arch/arm/boot/dts/qcom-ipq4019.dtsi - -This was required on Mikrotik IPQ40XX consumer hardware using Mikrotik's -RouterBoot bootloader. - -Signed-off-by: John Thomson ---- - arch/arm/boot/compressed/head.S | 35 +++++++++++++++++++++++++++++++++ - 1 file changed, 35 insertions(+) - ---- a/arch/arm/boot/compressed/head.S -+++ b/arch/arm/boot/compressed/head.S -@@ -602,6 +602,41 @@ not_relocated: mov r0, #0 - bic r4, r4, #1 - blne cache_on - -+/* Set the Qualcom IPQ40xx watchdog timeout to 30 seconds -+ * if it is enabled, so that there is time for kernel -+ * to decompress, boot, and take over the watchdog. -+ * data and functionality from drivers/watchdog/qcom-wdt.c -+ * address from arch/arm/boot/dts/qcom-ipq4019.dtsi -+ */ -+#ifdef CONFIG_ARCH_IPQ40XX -+watchdog_set: -+ /* offsets: -+ * 0x04 reset (=1 resets countdown) -+ * 0x08 enable (=0 disables) -+ * 0x0c status (=1 when SoC was reset by watchdog) -+ * 0x10 bark (=timeout warning in ticks) -+ * 0x14 bite (=timeout reset in ticks) -+ * clock rate is 1<<15 hertz -+ */ -+ .equ watchdog, 0x0b017000 @Store watchdog base address -+ movw r0, #:lower16:watchdog -+ movt r0, #:upper16:watchdog -+ ldr r1, [r0, #0x08] @Get enabled? -+ cmp r1, #1 @If not enabled, do not change -+ bne watchdog_finished -+ mov r1, #0 -+ str r1, [r0, #0x08] @Disable the watchdog -+ mov r1, #1 -+ str r1, [r0, #0x04] @Pet the watchdog -+ mov r1, #30 @30 seconds timeout -+ lsl r1, r1, #15 @converted to ticks -+ str r1, [r0, #0x10] @Set the bark timeout -+ str r1, [r0, #0x14] @Set the bite timeout -+ mov r1, #1 -+ str r1, [r0, #0x08] @Enable the watchdog -+watchdog_finished: -+#endif /* CONFIG_ARCH_IPQ40XX */ -+ - /* - * The C runtime environment should now be setup sufficiently. - * Set up some pointers, and start decompressing. diff --git a/target/linux/ipq40xx/patches-5.10/400-mmc-sdhci-sdhci-msm-use-sdhci_set_clock-instead-of-s.patch b/target/linux/ipq40xx/patches-5.10/400-mmc-sdhci-sdhci-msm-use-sdhci_set_clock-instead-of-s.patch deleted file mode 100644 index 07d274f0dd..0000000000 --- a/target/linux/ipq40xx/patches-5.10/400-mmc-sdhci-sdhci-msm-use-sdhci_set_clock-instead-of-s.patch +++ /dev/null @@ -1,24 +0,0 @@ -From f63ea127643a605da97090ce585fdd7c2d17fa42 Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Mon, 14 Dec 2020 13:35:35 +0100 -Subject: [PATCH] mmc: sdhci-msm: use sdhci_set_clock - -When using sdhci_msm_set_clock clock setting will fail, so lets -use the generic sdhci_set_clock. - -Signed-off-by: Robert Marko ---- - drivers/mmc/host/sdhci-msm.c | 2 +- - 1 file changed, 1 insertion(+), 1 deletion(-) - ---- a/drivers/mmc/host/sdhci-msm.c -+++ b/drivers/mmc/host/sdhci-msm.c -@@ -2193,7 +2193,7 @@ MODULE_DEVICE_TABLE(of, sdhci_msm_dt_mat - - static const struct sdhci_ops sdhci_msm_ops = { - .reset = sdhci_msm_reset, -- .set_clock = sdhci_msm_set_clock, -+ .set_clock = sdhci_set_clock, - .get_min_clock = sdhci_msm_get_min_clock, - .get_max_clock = sdhci_msm_get_max_clock, - .set_bus_width = sdhci_set_bus_width, diff --git a/target/linux/ipq40xx/patches-5.10/420-firmware-qcom-scm-disable-SDI.patch b/target/linux/ipq40xx/patches-5.10/420-firmware-qcom-scm-disable-SDI.patch deleted file mode 100644 index 27e3f42770..0000000000 --- a/target/linux/ipq40xx/patches-5.10/420-firmware-qcom-scm-disable-SDI.patch +++ /dev/null @@ -1,47 +0,0 @@ ---- a/drivers/firmware/qcom_scm.c -+++ b/drivers/firmware/qcom_scm.c -@@ -404,6 +404,20 @@ static int __qcom_scm_set_dload_mode(str - return qcom_scm_call_atomic(__scm->dev, &desc, NULL); - } - -+static int __qcom_scm_disable_sdi(struct device *dev) -+{ -+ struct qcom_scm_desc desc = { -+ .svc = QCOM_SCM_SVC_BOOT, -+ .cmd = QCOM_SCM_BOOT_CONFIG_SDI, -+ .arginfo = QCOM_SCM_ARGS(2), -+ .args[0] = 1 /* 1: disable watchdog debug */, -+ .args[1] = 0 /* 0: disable SDI */, -+ .owner = ARM_SMCCC_OWNER_SIP, -+ }; -+ -+ return qcom_scm_call(__scm->dev, &desc, NULL); -+} -+ - static void qcom_scm_set_download_mode(bool enable) - { - bool avail; -@@ -1250,6 +1264,13 @@ static int qcom_scm_probe(struct platfor - if (download_mode) - qcom_scm_set_download_mode(true); - -+ /* -+ * Factory firmware leaves SDI (a debug interface), which prevents -+ * clean reboot. -+ */ -+ if (of_machine_is_compatible("google,wifi")) -+ __qcom_scm_disable_sdi(__scm->dev); -+ - return 0; - } - ---- a/drivers/firmware/qcom_scm.h -+++ b/drivers/firmware/qcom_scm.h -@@ -77,6 +77,7 @@ extern int scm_legacy_call(struct device - #define QCOM_SCM_SVC_BOOT 0x01 - #define QCOM_SCM_BOOT_SET_ADDR 0x01 - #define QCOM_SCM_BOOT_TERMINATE_PC 0x02 -+#define QCOM_SCM_BOOT_CONFIG_SDI 0x09 - #define QCOM_SCM_BOOT_SET_DLOAD_MODE 0x10 - #define QCOM_SCM_BOOT_SET_REMOTE_STATE 0x0a - #define QCOM_SCM_FLUSH_FLAG_MASK 0x3 diff --git a/target/linux/ipq40xx/patches-5.10/421-firmware-qcom-scm-cold-boot-address.patch b/target/linux/ipq40xx/patches-5.10/421-firmware-qcom-scm-cold-boot-address.patch deleted file mode 100644 index accf3e9686..0000000000 --- a/target/linux/ipq40xx/patches-5.10/421-firmware-qcom-scm-cold-boot-address.patch +++ /dev/null @@ -1,121 +0,0 @@ ---- a/drivers/firmware/qcom_scm-legacy.c -+++ b/drivers/firmware/qcom_scm-legacy.c -@@ -13,6 +13,9 @@ - #include - #include - -+#include -+#include -+ - #include "qcom_scm.h" - - static DEFINE_MUTEX(qcom_scm_lock); -@@ -117,6 +120,25 @@ static void __scm_legacy_do(const struct - } while (res->a0 == QCOM_SCM_INTERRUPTED); - } - -+static void qcom_scm_inv_range(unsigned long start, unsigned long end) -+{ -+ u32 cacheline_size, ctr; -+ -+ asm volatile("mrc p15, 0, %0, c0, c0, 1" : "=r" (ctr)); -+ cacheline_size = 4 << ((ctr >> 16) & 0xf); -+ -+ start = round_down(start, cacheline_size); -+ end = round_up(end, cacheline_size); -+ outer_inv_range(start, end); -+ while (start < end) { -+ asm ("mcr p15, 0, %0, c7, c6, 1" : : "r" (start) -+ : "memory"); -+ start += cacheline_size; -+ } -+ dsb(); -+ isb(); -+} -+ - /** - * qcom_scm_call() - Sends a command to the SCM and waits for the command to - * finish processing. -@@ -160,10 +182,16 @@ int scm_legacy_call(struct device *dev, - - rsp = scm_legacy_command_to_response(cmd); - -- cmd_phys = dma_map_single(dev, cmd, alloc_len, DMA_TO_DEVICE); -- if (dma_mapping_error(dev, cmd_phys)) { -- kfree(cmd); -- return -ENOMEM; -+ if (dev) { -+ cmd_phys = dma_map_single(dev, cmd, alloc_len, DMA_TO_DEVICE); -+ if (dma_mapping_error(dev, cmd_phys)) { -+ kfree(cmd); -+ return -ENOMEM; -+ } -+ } else { -+ cmd_phys = virt_to_phys(cmd); -+ __cpuc_flush_dcache_area(cmd, alloc_len); -+ outer_flush_range(cmd_phys, cmd_phys + alloc_len); - } - - smc.args[0] = 1; -@@ -179,13 +207,26 @@ int scm_legacy_call(struct device *dev, - goto out; - - do { -- dma_sync_single_for_cpu(dev, cmd_phys + sizeof(*cmd) + cmd_len, -- sizeof(*rsp), DMA_FROM_DEVICE); -+ if (dev) { -+ dma_sync_single_for_cpu(dev, cmd_phys + sizeof(*cmd) + -+ cmd_len, sizeof(*rsp), -+ DMA_FROM_DEVICE); -+ } else { -+ unsigned long start = (uintptr_t)cmd + sizeof(*cmd) + -+ cmd_len; -+ qcom_scm_inv_range(start, start + sizeof(*rsp)); -+ } - } while (!rsp->is_complete); - -- dma_sync_single_for_cpu(dev, cmd_phys + sizeof(*cmd) + cmd_len + -- le32_to_cpu(rsp->buf_offset), -- resp_len, DMA_FROM_DEVICE); -+ if (dev) { -+ dma_sync_single_for_cpu(dev, cmd_phys + sizeof(*cmd) + cmd_len + -+ le32_to_cpu(rsp->buf_offset), -+ resp_len, DMA_FROM_DEVICE); -+ } else { -+ unsigned long start = (uintptr_t)cmd + sizeof(*cmd) + cmd_len + -+ le32_to_cpu(rsp->buf_offset); -+ qcom_scm_inv_range(start, start + resp_len); -+ } - - if (res) { - res_buf = scm_legacy_get_response_buffer(rsp); -@@ -193,7 +234,8 @@ int scm_legacy_call(struct device *dev, - res->result[i] = le32_to_cpu(res_buf[i]); - } - out: -- dma_unmap_single(dev, cmd_phys, alloc_len, DMA_TO_DEVICE); -+ if (dev) -+ dma_unmap_single(dev, cmd_phys, alloc_len, DMA_TO_DEVICE); - kfree(cmd); - return ret; - } ---- a/drivers/firmware/qcom_scm.c -+++ b/drivers/firmware/qcom_scm.c -@@ -344,6 +344,17 @@ int qcom_scm_set_cold_boot_addr(void *en - desc.args[0] = flags; - desc.args[1] = virt_to_phys(entry); - -+ /* -+ * Factory firmware doesn't support the atomic variant. Non-atomic SCMs -+ * require ugly DMA invalidation support that was dropped upstream a -+ * while ago. For more info, see: -+ * -+ * [RFC] qcom_scm: IPQ4019 firmware does not support atomic API? -+ * https://lore.kernel.org/linux-arm-msm/20200913201608.GA3162100@bDebian/ -+ */ -+ if (of_machine_is_compatible("google,wifi")) -+ return qcom_scm_call(__scm ? __scm->dev : NULL, &desc, NULL); -+ - return qcom_scm_call_atomic(__scm ? __scm->dev : NULL, &desc, NULL); - } - EXPORT_SYMBOL(qcom_scm_set_cold_boot_addr); diff --git a/target/linux/ipq40xx/patches-5.10/444-mtd-nand-rawnand-add-support-for-Toshiba-TC58NVG0S3H.patch b/target/linux/ipq40xx/patches-5.10/444-mtd-nand-rawnand-add-support-for-Toshiba-TC58NVG0S3H.patch deleted file mode 100644 index 91919b2894..0000000000 --- a/target/linux/ipq40xx/patches-5.10/444-mtd-nand-rawnand-add-support-for-Toshiba-TC58NVG0S3H.patch +++ /dev/null @@ -1,29 +0,0 @@ -From 35ca7e3e6ccd120d694a3425f37fc6374ad2e11e Mon Sep 17 00:00:00 2001 -From: =?UTF-8?q?Andreas=20B=C3=B6hler?= -Date: Wed, 20 Apr 2022 12:08:38 +0200 -Subject: [PATCH] mtd: rawnand: add support for Toshiba TC58NVG0S3HTA00 - NAND flash -MIME-Version: 1.0 -Content-Type: text/plain; charset=UTF-8 -Content-Transfer-Encoding: 8bit - -The Toshiba TC58NVG0S3HTA00 is detected with 64 byte OOB while the flash -has 128 bytes OOB. This adds a static NAND ID entry to correct this. - -Tested on FRITZ!Box 7530 flashed with OpenWrt. - -Signed-off-by: Andreas Böhler -(changed id_len to 8, added comment about possible counterfeits) ---- ---- a/drivers/mtd/nand/raw/nand_ids.c -+++ b/drivers/mtd/nand/raw/nand_ids.c -@@ -29,6 +29,9 @@ struct nand_flash_dev nand_flash_ids[] = - {"TC58NVG0S3E 1G 3.3V 8-bit", - { .id = {0x98, 0xd1, 0x90, 0x15, 0x76, 0x14, 0x01, 0x00} }, - SZ_2K, SZ_128, SZ_128K, 0, 8, 64, NAND_ECC_INFO(1, SZ_512), }, -+ {"TC58NVG0S3HTA00 1G 3.3V 8-bit", /* possibly counterfeit chip - see commit */ -+ { .id = {0x98, 0xf1, 0x80, 0x15} }, /* should be more bytes */ -+ SZ_2K, SZ_128, SZ_128K, 0, 8, 128, NAND_ECC_INFO(8, SZ_512), }, - {"TC58NVG2S0F 4G 3.3V 8-bit", - { .id = {0x98, 0xdc, 0x90, 0x26, 0x76, 0x15, 0x01, 0x08} }, - SZ_4K, SZ_512, SZ_256K, 0, 8, 224, NAND_ECC_INFO(4, SZ_512) }, diff --git a/target/linux/ipq40xx/patches-5.10/700-skbuff-add-DSA-specific-data-to-struct-skb_shared_in.patch b/target/linux/ipq40xx/patches-5.10/700-skbuff-add-DSA-specific-data-to-struct-skb_shared_in.patch deleted file mode 100644 index 7cad65aa0a..0000000000 --- a/target/linux/ipq40xx/patches-5.10/700-skbuff-add-DSA-specific-data-to-struct-skb_shared_in.patch +++ /dev/null @@ -1,43 +0,0 @@ -From da75807ac41175e9db8c95f7a172b4133763b744 Mon Sep 17 00:00:00 2001 -From: Gabor Juhos -Date: Mon, 11 Jan 2021 17:49:36 +0100 -Subject: [PATCH] skbuff: add DSA specific data to struct skb_shared_info - -All of the already existing DSA tagging protocol drivers -are storing the tagging data directly into the skb. In most -cases that is the only way to send the required information -to the underlying ethernet switch. - -However on certain platforms (like the Qualcomm IPQ40xx -SoCs) the built-in ethernet switch is connected directly -to an ethernet MAC, and the tagging information must be -sent out-of-band which is done directly via the hardware -TX descriptors of the ethernet MAC. - -In such cases, putting the information into the skb causes -unneccesary overhead, because the ethernet driver must -remove that before sending the ethernet frame towards to -the hardware. - -This change adds two new DSA specific fields to struct -skb_shared_info which makes it possible to send the -tagging information via skb->shinfo. With this approach, -the twofold modifications of the skb data can be avoided. - -Signed-off-by: Gabor Juhos ---- - include/linux/skbuff.h | 3 +++ - 1 file changed, 3 insertions(+) - ---- a/include/linux/skbuff.h -+++ b/include/linux/skbuff.h -@@ -522,6 +522,9 @@ struct skb_shared_info { - unsigned int gso_type; - u32 tskey; - -+ unsigned int dsa_tag_proto; -+ unsigned char dsa_tag_data[8]; -+ - /* - * Warning : all fields before dataref are cleared in __alloc_skb() - */ diff --git a/target/linux/ipq40xx/patches-5.10/701-net-dsa-tag_ipq4019-add-shinfo-based-tagging-driver-.patch b/target/linux/ipq40xx/patches-5.10/701-net-dsa-tag_ipq4019-add-shinfo-based-tagging-driver-.patch deleted file mode 100644 index 133f1b8a96..0000000000 --- a/target/linux/ipq40xx/patches-5.10/701-net-dsa-tag_ipq4019-add-shinfo-based-tagging-driver-.patch +++ /dev/null @@ -1,188 +0,0 @@ -From 29a0c2fae991cab142575c92276c0afdeb260ebe Mon Sep 17 00:00:00 2001 -From: Gabor Juhos -Date: Thu, 28 Oct 2021 21:44:52 +0200 -Subject: [PATCH] net: dsa: tag_ipq4019: add shinfo based tagging driver for - IPQ40xx - -This change adds a tagging protocol driver for the built-in -ethernet switch of the Qualcomm Atheros IPQ4019 SoCs. - -In comparison to the existing tagging protocols this hardware -requires a slightly different approach because the switch does -not use in-band tags. - -On the receive path, the source port information is embedded -into the RX descriptors of the ethernet MAC hardware. Similarly, -the destination port mask must be sent via the TX descriptors -of the ethernet MAC when a packet is sent towards the switch. - -In order to support this special requirements, this patch -adds a new tagging protocol driver. - -The driver extracts the source port information directly -from the 'receive return descriptor' of the ethernet MAC. -It is possible because that descriptor is part of the skb -received from the ethernet driver. - -Unfortunatley, it is not possible to put the destination -port information directly to the TX descriptors, because -those are handled internally by the driver of the ethernet -hardware. - -To overcome this limitation, this tagging driver uses the -DSA specific fields in skb->shinfo to send the destination -port information to the ethernet driver. - -A similar tagging driver is exist but that uses skb -extensions which causes unnecessary overhead. - -Signed-off-by: Gabor Juhos ---- - include/linux/dsa/ipq4019.h | 11 ++++++ - include/net/dsa.h | 2 + - net/dsa/Kconfig | 6 +++ - net/dsa/Makefile | 1 + - net/dsa/tag_ipq4019.c | 79 +++++++++++++++++++++++++++++++++++++ - 5 files changed, 99 insertions(+) - create mode 100644 include/linux/dsa/ipq4019.h - create mode 100644 net/dsa/tag_ipq4019.c - ---- /dev/null -+++ b/include/linux/dsa/ipq4019.h -@@ -0,0 +1,11 @@ -+/* SPDX-License-Identifier: GPL-2.0-only */ -+ -+#ifndef DSA_IPQ40XX_H -+#define DSA_IPQ40XX_H -+ -+struct ipq40xx_dsa_tag_data { -+ u8 from_cpu; -+ u8 dp; -+}; -+ -+#endif /* DSA_IPQ40XX_H */ ---- a/include/net/dsa.h -+++ b/include/net/dsa.h -@@ -46,6 +46,7 @@ struct phylink_link_state; - #define DSA_TAG_PROTO_AR9331_VALUE 16 - #define DSA_TAG_PROTO_RTL4_A_VALUE 17 - #define DSA_TAG_PROTO_BRCM_LEGACY_VALUE 22 -+#define DSA_TAG_PROTO_IPQ4019_VALUE 24 - - enum dsa_tag_protocol { - DSA_TAG_PROTO_NONE = DSA_TAG_PROTO_NONE_VALUE, -@@ -67,6 +68,7 @@ enum dsa_tag_protocol { - DSA_TAG_PROTO_OCELOT = DSA_TAG_PROTO_OCELOT_VALUE, - DSA_TAG_PROTO_AR9331 = DSA_TAG_PROTO_AR9331_VALUE, - DSA_TAG_PROTO_RTL4_A = DSA_TAG_PROTO_RTL4_A_VALUE, -+ DSA_TAG_PROTO_IPQ4019 = DSA_TAG_PROTO_IPQ4019_VALUE, - }; - - struct packet_type; ---- a/net/dsa/Kconfig -+++ b/net/dsa/Kconfig -@@ -63,6 +63,12 @@ config NET_DSA_TAG_BRCM_PREPEND - Broadcom switches which places the tag before the Ethernet header - (prepended). - -+config NET_DSA_TAG_IPQ4019 -+ tristate "Tag driver for Qualcomm Atheros IPQ4019 SoC built-in switch" -+ help -+ Say Y or M if you want to enable support for tagging frames for -+ the built-in switch of the Qualcomm Atheros IPQ4019 SoC-s. -+ - config NET_DSA_TAG_GSWIP - tristate "Tag driver for Lantiq / Intel GSWIP switches" - help ---- a/net/dsa/Makefile -+++ b/net/dsa/Makefile -@@ -10,6 +10,7 @@ obj-$(CONFIG_NET_DSA_TAG_BRCM_COMMON) += - obj-$(CONFIG_NET_DSA_TAG_DSA) += tag_dsa.o - obj-$(CONFIG_NET_DSA_TAG_EDSA) += tag_edsa.o - obj-$(CONFIG_NET_DSA_TAG_GSWIP) += tag_gswip.o -+obj-$(CONFIG_NET_DSA_TAG_IPQ4019) += tag_ipq4019.o - obj-$(CONFIG_NET_DSA_TAG_KSZ) += tag_ksz.o - obj-$(CONFIG_NET_DSA_TAG_RTL4_A) += tag_rtl4_a.o - obj-$(CONFIG_NET_DSA_TAG_LAN9303) += tag_lan9303.o ---- /dev/null -+++ b/net/dsa/tag_ipq4019.c -@@ -0,0 +1,79 @@ -+// SPDX-License-Identifier: GPL-2.0-only -+ -+/* Copyright (c) 2021, Gabor Juhos */ -+ -+#include -+#include -+ -+#include "dsa_priv.h" -+ -+/* Receive Return Descriptor */ -+struct edma_rrd { -+ u16 rrd0; -+ u16 rrd1; -+ u16 rrd2; -+ u16 rrd3; -+ u16 rrd4; -+ u16 rrd5; -+ u16 rrd6; -+ u16 rrd7; -+} __packed; -+ -+#define EDMA_RRD_SIZE sizeof(struct edma_rrd) -+ -+#define EDMA_RRD1_PORT_ID_MASK GENMASK(14, 12) -+ -+static struct sk_buff *ipq4019_sh_tag_xmit(struct sk_buff *skb, -+ struct net_device *dev) -+{ -+ struct dsa_port *dp = dsa_slave_to_port(dev); -+ struct ipq40xx_dsa_tag_data *tag_data; -+ -+ BUILD_BUG_ON(sizeof_field(struct skb_shared_info, dsa_tag_data) < -+ sizeof(struct ipq40xx_dsa_tag_data)); -+ -+ skb_shinfo(skb)->dsa_tag_proto = DSA_TAG_PROTO_IPQ4019; -+ tag_data = (struct ipq40xx_dsa_tag_data *)skb_shinfo(skb)->dsa_tag_data; -+ -+ tag_data->from_cpu = 1; -+ /* set the destination port information */ -+ tag_data->dp = BIT(dp->index); -+ -+ return skb; -+} -+ -+static struct sk_buff *ipq4019_sh_tag_rcv(struct sk_buff *skb, -+ struct net_device *dev, -+ struct packet_type *pt) -+{ -+ struct edma_rrd *rrd; -+ int offset; -+ int port; -+ -+ offset = EDMA_RRD_SIZE + ETH_HLEN; -+ if (unlikely(skb_headroom(skb) < offset)) -+ return NULL; -+ -+ rrd = (struct edma_rrd *)(skb->data - offset); -+ port = FIELD_GET(EDMA_RRD1_PORT_ID_MASK, rrd->rrd1); -+ -+ skb->dev = dsa_master_find_slave(dev, 0, port); -+ if (!skb->dev) -+ return NULL; -+ -+ return skb; -+} -+ -+const struct dsa_device_ops ipq4019_sh_tag_dsa_ops = { -+ .name = "ipq4019-sh", -+ .proto = DSA_TAG_PROTO_IPQ4019, -+ .xmit = ipq4019_sh_tag_xmit, -+ .rcv = ipq4019_sh_tag_rcv, -+}; -+ -+MODULE_LICENSE("GPL v2"); -+MODULE_DESCRIPTION("DSA tag driver for the IPQ4019 SoC built-in ethernet switch"); -+MODULE_AUTHOR("Gabor Juhos "); -+MODULE_ALIAS_DSA_TAG_DRIVER(DSA_TAG_PROTO_IPQ4019); -+ -+module_dsa_tag_driver(ipq4019_sh_tag_dsa_ops); diff --git a/target/linux/ipq40xx/patches-5.10/702-net-ethernet-qualcomm-add-IPQESS-support.patch b/target/linux/ipq40xx/patches-5.10/702-net-ethernet-qualcomm-add-IPQESS-support.patch deleted file mode 100644 index 72e9345118..0000000000 --- a/target/linux/ipq40xx/patches-5.10/702-net-ethernet-qualcomm-add-IPQESS-support.patch +++ /dev/null @@ -1,43 +0,0 @@ -From 4f488235f498db43f2412116dea6e02c7fb20216 Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Mon, 1 Nov 2021 12:36:51 +0100 -Subject: [PATCH] net: ethernet: qualcomm: add IPQESS support - -Allow compiling the IPQESS driver that supports the -Qualcomm IPQ40xx SoC built-in ethernet controller. - -Signed-off-by: Robert Marko ---- - drivers/net/ethernet/qualcomm/Kconfig | 11 +++++++++++ - drivers/net/ethernet/qualcomm/Makefile | 1 + - 2 files changed, 12 insertions(+) - ---- a/drivers/net/ethernet/qualcomm/Kconfig -+++ b/drivers/net/ethernet/qualcomm/Kconfig -@@ -60,6 +60,17 @@ config QCOM_EMAC - low power, Receive-Side Scaling (RSS), and IEEE 1588-2008 - Precision Clock Synchronization Protocol. - -+config QCOM_IPQ4019_ESS_EDMA -+ tristate "Qualcomm Atheros IPQ4019 ESS EDMA support" -+ depends on OF -+ select PHYLINK -+ help -+ This driver supports the Qualcomm Atheros IPQ40xx built-in -+ ESS EDMA ethernet controller. -+ -+ To compile this driver as a module, choose M here: the -+ module will be called ipqess. -+ - source "drivers/net/ethernet/qualcomm/rmnet/Kconfig" - - endif # NET_VENDOR_QUALCOMM ---- a/drivers/net/ethernet/qualcomm/Makefile -+++ b/drivers/net/ethernet/qualcomm/Makefile -@@ -10,5 +10,6 @@ obj-$(CONFIG_QCA7000_UART) += qcauart.o - qcauart-objs := qca_uart.o - - obj-y += emac/ -+obj-y += ipqess/ - - obj-$(CONFIG_RMNET) += rmnet/ diff --git a/target/linux/ipq40xx/patches-5.10/703-arm-dts-ipq4019-add-ethernet-controller-DT-node.patch b/target/linux/ipq40xx/patches-5.10/703-arm-dts-ipq4019-add-ethernet-controller-DT-node.patch deleted file mode 100644 index 68fb4eb4ce..0000000000 --- a/target/linux/ipq40xx/patches-5.10/703-arm-dts-ipq4019-add-ethernet-controller-DT-node.patch +++ /dev/null @@ -1,81 +0,0 @@ -From 44327d7098d4f32c24ec8c528e5aff6e030956bc Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Wed, 20 Oct 2021 13:21:45 +0200 -Subject: [PATCH] arm: dts: ipq4019: add ethernet controller DT node - -Since IPQ40xx SoC built-in ethernet controller now has a driver, -add its DT node so it can be used. - -Signed-off-by: Robert Marko ---- - arch/arm/boot/dts/qcom-ipq4019.dtsi | 48 +++++++++++++++++++++++++++++ - 1 file changed, 48 insertions(+) - ---- a/arch/arm/boot/dts/qcom-ipq4019.dtsi -+++ b/arch/arm/boot/dts/qcom-ipq4019.dtsi -@@ -38,6 +38,7 @@ - spi1 = &blsp1_spi2; - i2c0 = &blsp1_i2c3; - i2c1 = &blsp1_i2c4; -+ ethernet0 = &gmac; - }; - - cpus { -@@ -589,6 +590,57 @@ - status = "disabled"; - }; - -+ gmac: ethernet@c080000 { -+ compatible = "qcom,ipq4019-ess-edma"; -+ reg = <0xc080000 0x8000>; -+ resets = <&gcc ESS_RESET>; -+ reset-names = "ess_rst"; -+ clocks = <&gcc GCC_ESS_CLK>; -+ clock-names = "ess_clk"; -+ interrupts = , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ , -+ ; -+ -+ status = "disabled"; -+ -+ phy-mode = "internal"; -+ fixed-link { -+ speed = <1000>; -+ full-duplex; -+ pause; -+ asym-pause; -+ }; -+ }; -+ - mdio: mdio@90000 { - #address-cells = <1>; - #size-cells = <0>; diff --git a/target/linux/ipq40xx/patches-5.10/704-net-phy-define-PSGMII-PHY-interface-mode.patch b/target/linux/ipq40xx/patches-5.10/704-net-phy-define-PSGMII-PHY-interface-mode.patch deleted file mode 100644 index b98201e0d0..0000000000 --- a/target/linux/ipq40xx/patches-5.10/704-net-phy-define-PSGMII-PHY-interface-mode.patch +++ /dev/null @@ -1,61 +0,0 @@ -From 3e1825e00dafb68eec25df389b63f3ab3d905b59 Mon Sep 17 00:00:00 2001 -From: Gabor Juhos -Date: Fri, 25 Dec 2020 08:02:47 +0100 -Subject: [PATCH] net: phy: define PSGMII PHY interface mode - -The PSGMII interface is similar to QSGMII. The main difference -is that the PSGMII interface combines five SGMII lines into a -single link while in QSGMII only four lines are combined. - -Similarly to the QSGMII, this interface mode might also needs -special handling within the MAC driver. - -Add definitions for the PHY layer to allow to express this type -of connection between the MAC and PHY. - -Signed-off-by: Gabor Juhos ---- - Documentation/devicetree/bindings/net/ethernet-controller.yaml | 1 + - drivers/net/phy/phylink.c | 1 + - include/linux/phy.h | 3 +++ - 3 files changed, 5 insertions(+) - ---- a/Documentation/devicetree/bindings/net/ethernet-controller.yaml -+++ b/Documentation/devicetree/bindings/net/ethernet-controller.yaml -@@ -64,6 +64,7 @@ properties: - - mii - - gmii - - sgmii -+ - psgmii - - qsgmii - - tbi - - rev-mii ---- a/drivers/net/phy/phylink.c -+++ b/drivers/net/phy/phylink.c -@@ -289,6 +289,7 @@ static int phylink_parse_mode(struct phy - - switch (pl->link_config.interface) { - case PHY_INTERFACE_MODE_SGMII: -+ case PHY_INTERFACE_MODE_PSGMII: - case PHY_INTERFACE_MODE_QSGMII: - phylink_set(pl->supported, 10baseT_Half); - phylink_set(pl->supported, 10baseT_Full); ---- a/include/linux/phy.h -+++ b/include/linux/phy.h -@@ -134,6 +134,7 @@ typedef enum { - PHY_INTERFACE_MODE_XGMII, - PHY_INTERFACE_MODE_XLGMII, - PHY_INTERFACE_MODE_MOCA, -+ PHY_INTERFACE_MODE_PSGMII, - PHY_INTERFACE_MODE_QSGMII, - PHY_INTERFACE_MODE_TRGMII, - PHY_INTERFACE_MODE_100BASEX, -@@ -201,6 +202,8 @@ static inline const char *phy_modes(phy_ - return "xlgmii"; - case PHY_INTERFACE_MODE_MOCA: - return "moca"; -+ case PHY_INTERFACE_MODE_PSGMII: -+ return "psgmii"; - case PHY_INTERFACE_MODE_QSGMII: - return "qsgmii"; - case PHY_INTERFACE_MODE_TRGMII: diff --git a/target/linux/ipq40xx/patches-5.10/705-net-dsa-add-Qualcomm-IPQ4019-built-in-switch-support.patch b/target/linux/ipq40xx/patches-5.10/705-net-dsa-add-Qualcomm-IPQ4019-built-in-switch-support.patch deleted file mode 100644 index ed201b7c58..0000000000 --- a/target/linux/ipq40xx/patches-5.10/705-net-dsa-add-Qualcomm-IPQ4019-built-in-switch-support.patch +++ /dev/null @@ -1,53 +0,0 @@ -From b5f71652b85a85ea53162e9e2b760b84fd0d254f Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Mon, 1 Nov 2021 18:10:28 +0100 -Subject: [PATCH] net: dsa: add Qualcomm IPQ4019 built-in switch support - -Qualcomm IPQ40xx SoC-s have a variant of QCA8337N switch built-in. - -It shares most of the stuff with its external counterpart, however it is -modified for the SoC. -Namely, it doesn't have second CPU port (Port 6), so it has 6 ports -instead of 7. -It also has no built-in PHY-s but rather requires external PSGMII based -companion PHY-s (QCA8072 and QCA8075) for which it first needs to carry -out calibration before using them. -PSGMII has a SoC built-in PHY that is used to connect to the PHY-s which -unfortunately requires some magic values as the datasheet doesnt document -the bits that are being set or the register at all. - -Since its built-in it is MMIO like other peripherals and doesn't have its -own MDIO bus but depends on the SoC provided one. - -CPU connection is at Port 0 and it uses some kind of a internal connection -and no traditional RGMII/SGMII. -It also doesn't use in-band tagging like other qca8k switches so a shinfo -based tagger is used. - -Signed-off-by: Robert Marko ---- - drivers/net/dsa/qca/Kconfig | 9 +++++++++ - drivers/net/dsa/qca/Makefile | 1 + - 2 files changed, 10 insertions(+) - ---- a/drivers/net/dsa/qca/Kconfig -+++ b/drivers/net/dsa/qca/Kconfig -@@ -7,3 +7,12 @@ config NET_DSA_AR9331 - help - This enables support for the Qualcomm Atheros AR9331 built-in Ethernet - switch. -+ -+config NET_DSA_QCA8K_IPQ4019 -+ tristate "Qualcomm Atheros IPQ4019 built-in Ethernet switch support" -+ depends on HAS_IOMEM && NET_DSA -+ select NET_DSA_TAG_IPQ4019 -+ select REGMAP -+ help -+ This enables support for the Qualcomm Atheros IPQ4019 SoC built-in -+ Ethernet switch. ---- a/drivers/net/dsa/qca/Makefile -+++ b/drivers/net/dsa/qca/Makefile -@@ -1,2 +1,3 @@ - # SPDX-License-Identifier: GPL-2.0-only - obj-$(CONFIG_NET_DSA_AR9331) += ar9331.o -+obj-$(CONFIG_NET_DSA_QCA8K_IPQ4019) += qca8k-ipq4019.o diff --git a/target/linux/ipq40xx/patches-5.10/706-arm-dts-ipq4019-add-switch-node.patch b/target/linux/ipq40xx/patches-5.10/706-arm-dts-ipq4019-add-switch-node.patch deleted file mode 100644 index a231c7331b..0000000000 --- a/target/linux/ipq40xx/patches-5.10/706-arm-dts-ipq4019-add-switch-node.patch +++ /dev/null @@ -1,98 +0,0 @@ -From ebb62523990a27b3a25e422fa575619f7f725a20 Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Mon, 1 Nov 2021 18:15:04 +0100 -Subject: [PATCH] arm: dts: ipq4019: add switch node - -Since the built-in IPQ40xx switch now has a driver, add the required node -for it to work. - -Signed-off-by: Robert Marko ---- - arch/arm/boot/dts/qcom-ipq4019.dtsi | 78 +++++++++++++++++++++++++++++ - 1 file changed, 78 insertions(+) - ---- a/arch/arm/boot/dts/qcom-ipq4019.dtsi -+++ b/arch/arm/boot/dts/qcom-ipq4019.dtsi -@@ -590,6 +590,82 @@ - status = "disabled"; - }; - -+ switch: switch@c000000 { -+ compatible = "qca,ipq4019-qca8337n"; -+ reg = <0xc000000 0x80000>, <0x98000 0x800>; -+ reg-names = "base", "psgmii_phy"; -+ resets = <&gcc ESS_PSGMII_ARES>; -+ reset-names = "psgmii_rst"; -+ mdio = <&mdio>; -+ psgmii-ethphy = <&psgmiiphy>; -+ -+ status = "disabled"; -+ -+ ports { -+ #address-cells = <1>; -+ #size-cells = <0>; -+ -+ port@0 { /* MAC0 */ -+ reg = <0>; -+ label = "cpu"; -+ ethernet = <&gmac>; -+ phy-mode = "internal"; -+ -+ fixed-link { -+ speed = <1000>; -+ full-duplex; -+ pause; -+ asym-pause; -+ }; -+ }; -+ -+ swport1: port@1 { /* MAC1 */ -+ reg = <1>; -+ label = "lan1"; -+ phy-handle = <ðphy0>; -+ phy-mode = "psgmii"; -+ -+ status = "disabled"; -+ }; -+ -+ swport2: port@2 { /* MAC2 */ -+ reg = <2>; -+ label = "lan2"; -+ phy-handle = <ðphy1>; -+ phy-mode = "psgmii"; -+ -+ status = "disabled"; -+ }; -+ -+ swport3: port@3 { /* MAC3 */ -+ reg = <3>; -+ label = "lan3"; -+ phy-handle = <ðphy2>; -+ phy-mode = "psgmii"; -+ -+ status = "disabled"; -+ }; -+ -+ swport4: port@4 { /* MAC4 */ -+ reg = <4>; -+ label = "lan4"; -+ phy-handle = <ðphy3>; -+ phy-mode = "psgmii"; -+ -+ status = "disabled"; -+ }; -+ -+ swport5: port@5 { /* MAC5 */ -+ reg = <5>; -+ label = "wan"; -+ phy-handle = <ðphy4>; -+ phy-mode = "psgmii"; -+ -+ status = "disabled"; -+ }; -+ }; -+ }; -+ - gmac: ethernet@c080000 { - compatible = "qcom,ipq4019-ess-edma"; - reg = <0xc080000 0x8000>; diff --git a/target/linux/ipq40xx/patches-5.10/707-dt-bindings-net-add-QCA807x-PHY.patch b/target/linux/ipq40xx/patches-5.10/707-dt-bindings-net-add-QCA807x-PHY.patch deleted file mode 100644 index dfb8d692ab..0000000000 --- a/target/linux/ipq40xx/patches-5.10/707-dt-bindings-net-add-QCA807x-PHY.patch +++ /dev/null @@ -1,61 +0,0 @@ -From c66863c1ba8995b61e6d727d78a241c734f5bb57 Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Thu, 1 Oct 2020 15:05:35 +0200 -Subject: [PATCH] dt-bindings: net: add QCA807x PHY - -Add DT bindings for Qualcomm QCA807x PHY series. - -Signed-off-by: Robert Marko ---- - include/dt-bindings/net/qcom-qca807x.h | 45 ++++++++++++++++++++++++++ - 1 file changed, 45 insertions(+) - create mode 100644 include/dt-bindings/net/qcom-qca807x.h - ---- /dev/null -+++ b/include/dt-bindings/net/qcom-qca807x.h -@@ -0,0 +1,45 @@ -+/* SPDX-License-Identifier: GPL-2.0-or-later */ -+/* -+ * Device Tree constants for the Qualcomm QCA807X PHYs -+ */ -+ -+#ifndef _DT_BINDINGS_QCOM_QCA807X_H -+#define _DT_BINDINGS_QCOM_QCA807X_H -+ -+#define PSGMII_QSGMII_TX_DRIVER_140MV 0 -+#define PSGMII_QSGMII_TX_DRIVER_160MV 1 -+#define PSGMII_QSGMII_TX_DRIVER_180MV 2 -+#define PSGMII_QSGMII_TX_DRIVER_200MV 3 -+#define PSGMII_QSGMII_TX_DRIVER_220MV 4 -+#define PSGMII_QSGMII_TX_DRIVER_240MV 5 -+#define PSGMII_QSGMII_TX_DRIVER_260MV 6 -+#define PSGMII_QSGMII_TX_DRIVER_280MV 7 -+#define PSGMII_QSGMII_TX_DRIVER_300MV 8 -+#define PSGMII_QSGMII_TX_DRIVER_320MV 9 -+#define PSGMII_QSGMII_TX_DRIVER_400MV 10 -+#define PSGMII_QSGMII_TX_DRIVER_500MV 11 -+/* Default value */ -+#define PSGMII_QSGMII_TX_DRIVER_600MV 12 -+ -+/* Full amplitude, full bias current */ -+#define QCA807X_CONTROL_DAC_FULL_VOLT_BIAS 0 -+/* Amplitude follow DSP (amplitude is adjusted based on cable length), half bias current */ -+#define QCA807X_CONTROL_DAC_DSP_VOLT_HALF_BIAS 1 -+/* Full amplitude, bias current follow DSP (bias current is adjusted based on cable length) */ -+#define QCA807X_CONTROL_DAC_FULL_VOLT_DSP_BIAS 2 -+/* Both amplitude and bias current follow DSP */ -+#define QCA807X_CONTROL_DAC_DSP_VOLT_BIAS 3 -+/* Full amplitude, half bias current */ -+#define QCA807X_CONTROL_DAC_FULL_VOLT_HALF_BIAS 4 -+/* Amplitude follow DSP setting; 1/4 bias current when cable<10m, -+ * otherwise half bias current -+ */ -+#define QCA807X_CONTROL_DAC_DSP_VOLT_QUARTER_BIAS 5 -+/* Full amplitude; same bias current setting with “010” and “011”, -+ * but half more bias is reduced when cable <10m -+ */ -+#define QCA807X_CONTROL_DAC_FULL_VOLT_HALF_BIAS_SHORT 6 -+/* Amplitude follow DSP; same bias current setting with “110”, default value */ -+#define QCA807X_CONTROL_DAC_DSP_VOLT_HALF_BIAS_SHORT 7 -+ -+#endif diff --git a/target/linux/ipq40xx/patches-5.10/708-net-phy-Add-Qualcom-QCA807x-driver.patch b/target/linux/ipq40xx/patches-5.10/708-net-phy-Add-Qualcom-QCA807x-driver.patch deleted file mode 100644 index 12b21a803c..0000000000 --- a/target/linux/ipq40xx/patches-5.10/708-net-phy-Add-Qualcom-QCA807x-driver.patch +++ /dev/null @@ -1,50 +0,0 @@ -From f825cdc8bfde7616a14e2163f16303a8973031d2 Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Wed, 7 Oct 2020 17:38:48 +0200 -Subject: [PATCH] net: phy: Add Qualcom QCA807x driver - -This adds driver for the Qualcomm QCA8072 and QCA8075 PHY-s. - -They are 2 or 5 port IEEE 802.3 clause 22 compliant 10BASE-Te, 100BASE-TX and 1000BASE-T PHY-s. - -They feature 2 SerDes, one for PSGMII or QSGMII connection with MAC, while second one is SGMII for connection to MAC or fiber. - -Both models have a combo port that supports 1000BASE-X and 100BASE-FX fiber. - -Each PHY inside of QCA807x series has 4 digitally controlled output only pins that natively drive LED-s. -But some vendors used these to driver generic LED-s controlled by userspace, -so lets enable registering each PHY as GPIO controller and add driver for it. - -These are commonly used in Qualcomm IPQ40xx, IPQ60xx and IPQ807x boards. - -Signed-off-by: Robert Marko ---- - drivers/net/phy/Kconfig | 6 ++++++ - drivers/net/phy/Makefile | 1 + - 2 files changed, 7 insertions(+) - ---- a/drivers/net/phy/Kconfig -+++ b/drivers/net/phy/Kconfig -@@ -320,6 +320,12 @@ config AT803X_PHY - Currently supports the AR8030, AR8031, AR8033, AR8035 and internal - QCA8337(Internal qca8k PHY) model - -+config QCA807X_PHY -+ tristate "Qualcomm QCA807X PHYs" -+ depends on OF_MDIO -+ help -+ Currently supports the QCA8072 and QCA8075 models. -+ - config QSEMI_PHY - tristate "Quality Semiconductor PHYs" - help ---- a/drivers/net/phy/Makefile -+++ b/drivers/net/phy/Makefile -@@ -88,6 +88,7 @@ obj-$(CONFIG_MICROSEMI_PHY) += mscc/ - obj-$(CONFIG_NATIONAL_PHY) += national.o - obj-$(CONFIG_NXP_TJA11XX_PHY) += nxp-tja11xx.o - obj-$(CONFIG_QSEMI_PHY) += qsemi.o -+obj-$(CONFIG_QCA807X_PHY) += qca807x.o - obj-$(CONFIG_REALTEK_PHY) += realtek.o - obj-$(CONFIG_RENESAS_PHY) += uPD60620.o - obj-$(CONFIG_ROCKCHIP_PHY) += rockchip.o diff --git a/target/linux/ipq40xx/patches-5.10/709-arm-dts-ipq4019-QCA807x-properties.patch b/target/linux/ipq40xx/patches-5.10/709-arm-dts-ipq4019-QCA807x-properties.patch deleted file mode 100644 index cc4b44b393..0000000000 --- a/target/linux/ipq40xx/patches-5.10/709-arm-dts-ipq4019-QCA807x-properties.patch +++ /dev/null @@ -1,61 +0,0 @@ -From e0fa88eaa3c176b71e563da68949ac2ab45aaa61 Mon Sep 17 00:00:00 2001 -From: Robert Marko -Date: Fri, 2 Oct 2020 10:43:26 +0200 -Subject: [PATCH] arm: dts: ipq4019: QCA807x properties - -This adds necessary DT properties for QCA807x PHY-s to IPQ4019 DTSI. - -Signed-off-by: Robert Marko ---- - arch/arm/boot/dts/qcom-ipq4019.dtsi | 18 ++++++++++++++++++ - 1 file changed, 18 insertions(+) - ---- a/arch/arm/boot/dts/qcom-ipq4019.dtsi -+++ b/arch/arm/boot/dts/qcom-ipq4019.dtsi -@@ -8,6 +8,7 @@ - #include - #include - #include -+#include - - / { - #address-cells = <1>; -@@ -726,22 +727,38 @@ - - ethphy0: ethernet-phy@0 { - reg = <0>; -+ -+ qcom,control-dac = ; - }; - - ethphy1: ethernet-phy@1 { - reg = <1>; -+ -+ qcom,control-dac = ; - }; - - ethphy2: ethernet-phy@2 { - reg = <2>; -+ -+ qcom,control-dac = ; - }; - - ethphy3: ethernet-phy@3 { - reg = <3>; -+ -+ qcom,control-dac = ; - }; - - ethphy4: ethernet-phy@4 { - reg = <4>; -+ -+ qcom,control-dac = ; -+ }; -+ -+ psgmiiphy: psgmii-phy@5 { -+ reg = <5>; -+ -+ qcom,tx-driver-strength = ; - }; - }; - diff --git a/target/linux/ipq40xx/patches-5.10/850-soc-add-qualcomm-syscon.patch b/target/linux/ipq40xx/patches-5.10/850-soc-add-qualcomm-syscon.patch deleted file mode 100644 index b39237b1dd..0000000000 --- a/target/linux/ipq40xx/patches-5.10/850-soc-add-qualcomm-syscon.patch +++ /dev/null @@ -1,180 +0,0 @@ -From: Christian Lamparter -Subject: SoC: add qualcomm syscon ---- a/drivers/soc/qcom/Makefile -+++ b/drivers/soc/qcom/Makefile -@@ -21,6 +21,7 @@ obj-$(CONFIG_QCOM_SMP2P) += smp2p.o - obj-$(CONFIG_QCOM_SMSM) += smsm.o - obj-$(CONFIG_QCOM_SOCINFO) += socinfo.o - obj-$(CONFIG_QCOM_WCNSS_CTRL) += wcnss_ctrl.o -+obj-$(CONFIG_QCOM_TCSR) += qcom_tcsr.o - obj-$(CONFIG_QCOM_APR) += apr.o - obj-$(CONFIG_QCOM_LLCC) += llcc-qcom.o - obj-$(CONFIG_QCOM_RPMHPD) += rpmhpd.o ---- a/drivers/soc/qcom/Kconfig -+++ b/drivers/soc/qcom/Kconfig -@@ -190,6 +190,13 @@ config QCOM_SOCINFO - Say yes here to support the Qualcomm socinfo driver, providing - information about the SoC to user space. - -+config QCOM_TCSR -+ tristate "QCOM Top Control and Status Registers" -+ depends on ARCH_QCOM -+ help -+ Say y here to enable TCSR support. The TCSR provides control -+ functions for various peripherals. -+ - config QCOM_WCNSS_CTRL - tristate "Qualcomm WCNSS control driver" - depends on ARCH_QCOM || COMPILE_TEST ---- /dev/null -+++ b/drivers/soc/qcom/qcom_tcsr.c -@@ -0,0 +1,98 @@ -+/* -+ * Copyright (c) 2014, The Linux foundation. All rights reserved. -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License rev 2 and -+ * only rev 2 as published by the free Software foundation. -+ * -+ * This program is distributed in the hope that it will be useful, -+ * but WITHOUT ANY WARRANTY; without even the implied warranty of -+ * MERCHANTABILITY or fITNESS fOR A PARTICULAR PURPOSE. See the -+ * GNU General Public License for more details. -+ */ -+ -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+ -+#define TCSR_USB_PORT_SEL 0xb0 -+#define TCSR_USB_HSPHY_CONFIG 0xC -+ -+#define TCSR_ESS_INTERFACE_SEL_OFFSET 0x0 -+#define TCSR_ESS_INTERFACE_SEL_MASK 0xf -+ -+#define TCSR_WIFI0_GLB_CFG_OFFSET 0x0 -+#define TCSR_WIFI1_GLB_CFG_OFFSET 0x4 -+#define TCSR_PNOC_SNOC_MEMTYPE_M0_M2 0x4 -+ -+static int tcsr_probe(struct platform_device *pdev) -+{ -+ struct resource *res; -+ const struct device_node *node = pdev->dev.of_node; -+ void __iomem *base; -+ u32 val; -+ -+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0); -+ base = devm_ioremap_resource(&pdev->dev, res); -+ if (IS_ERR(base)) -+ return PTR_ERR(base); -+ -+ if (!of_property_read_u32(node, "qcom,usb-ctrl-select", &val)) { -+ dev_err(&pdev->dev, "setting usb port select = %d\n", val); -+ writel(val, base + TCSR_USB_PORT_SEL); -+ } -+ -+ if (!of_property_read_u32(node, "qcom,usb-hsphy-mode-select", &val)) { -+ dev_info(&pdev->dev, "setting usb hs phy mode select = %x\n", val); -+ writel(val, base + TCSR_USB_HSPHY_CONFIG); -+ } -+ -+ if (!of_property_read_u32(node, "qcom,ess-interface-select", &val)) { -+ u32 tmp = 0; -+ dev_info(&pdev->dev, "setting ess interface select = %x\n", val); -+ tmp = readl(base + TCSR_ESS_INTERFACE_SEL_OFFSET); -+ tmp = tmp & (~TCSR_ESS_INTERFACE_SEL_MASK); -+ tmp = tmp | (val&TCSR_ESS_INTERFACE_SEL_MASK); -+ writel(tmp, base + TCSR_ESS_INTERFACE_SEL_OFFSET); -+ } -+ -+ if (!of_property_read_u32(node, "qcom,wifi_glb_cfg", &val)) { -+ dev_info(&pdev->dev, "setting wifi_glb_cfg = %x\n", val); -+ writel(val, base + TCSR_WIFI0_GLB_CFG_OFFSET); -+ writel(val, base + TCSR_WIFI1_GLB_CFG_OFFSET); -+ } -+ -+ if (!of_property_read_u32(node, "qcom,wifi_noc_memtype_m0_m2", &val)) { -+ dev_info(&pdev->dev, -+ "setting wifi_noc_memtype_m0_m2 = %x\n", val); -+ writel(val, base + TCSR_PNOC_SNOC_MEMTYPE_M0_M2); -+ } -+ -+ return 0; -+} -+ -+static const struct of_device_id tcsr_dt_match[] = { -+ { .compatible = "qcom,tcsr", }, -+ { }, -+}; -+ -+MODULE_DEVICE_TABLE(of, tcsr_dt_match); -+ -+static struct platform_driver tcsr_driver = { -+ .driver = { -+ .name = "tcsr", -+ .owner = THIS_MODULE, -+ .of_match_table = tcsr_dt_match, -+ }, -+ .probe = tcsr_probe, -+}; -+ -+module_platform_driver(tcsr_driver); -+ -+MODULE_AUTHOR("Andy Gross "); -+MODULE_DESCRIPTION("QCOM TCSR driver"); -+MODULE_LICENSE("GPL v2"); ---- /dev/null -+++ b/include/dt-bindings/soc/qcom,tcsr.h -@@ -0,0 +1,48 @@ -+/* Copyright (c) 2014, The Linux Foundation. All rights reserved. -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License version 2 and -+ * only version 2 as published by the Free Software Foundation. -+ * -+ * This program is distributed in the hope that it will be useful, -+ * but WITHOUT ANY WARRANTY; without even the implied warranty of -+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -+ * GNU General Public License for more details. -+ */ -+#ifndef __DT_BINDINGS_QCOM_TCSR_H -+#define __DT_BINDINGS_QCOM_TCSR_H -+ -+#define TCSR_USB_SELECT_USB3_P0 0x1 -+#define TCSR_USB_SELECT_USB3_P1 0x2 -+#define TCSR_USB_SELECT_USB3_DUAL 0x3 -+ -+/* IPQ40xx HS PHY Mode Select */ -+#define TCSR_USB_HSPHY_HOST_MODE 0x00E700E7 -+#define TCSR_USB_HSPHY_DEVICE_MODE 0x00C700E7 -+ -+/* IPQ40xx ess interface mode select */ -+#define TCSR_ESS_PSGMII 0 -+#define TCSR_ESS_PSGMII_RGMII5 1 -+#define TCSR_ESS_PSGMII_RMII0 2 -+#define TCSR_ESS_PSGMII_RMII1 4 -+#define TCSR_ESS_PSGMII_RMII0_RMII1 6 -+#define TCSR_ESS_PSGMII_RGMII4 9 -+ -+/* -+ * IPQ40xx WiFi Global Config -+ * Bit 30:AXID_EN -+ * Enable AXI master bus Axid translating to confirm all txn submitted by order -+ * Bit 24: Use locally generated socslv_wxi_bvalid -+ * 1: use locally generate socslv_wxi_bvalid for performance. -+ * 0: use SNOC socslv_wxi_bvalid. -+ */ -+#define TCSR_WIFI_GLB_CFG 0x41000000 -+ -+/* IPQ40xx MEM_TYPE_SEL_M0_M2 Select Bit 26:24 - 2 NORMAL */ -+#define TCSR_WIFI_NOC_MEMTYPE_M0_M2 0x02222222 -+ -+/* TCSR A/B REG */ -+#define IPQ806X_TCSR_REG_A_ADM_CRCI_MUX_SEL 0 -+#define IPQ806X_TCSR_REG_B_ADM_CRCI_MUX_SEL 1 -+ -+#endif diff --git a/target/linux/ipq40xx/patches-5.10/900-dts-ipq4019-ap-dk01.1.patch b/target/linux/ipq40xx/patches-5.10/900-dts-ipq4019-ap-dk01.1.patch deleted file mode 100644 index 5a245eb431..0000000000 --- a/target/linux/ipq40xx/patches-5.10/900-dts-ipq4019-ap-dk01.1.patch +++ /dev/null @@ -1,176 +0,0 @@ ---- a/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi -+++ b/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi -@@ -15,6 +15,7 @@ - */ - - #include "qcom-ipq4019.dtsi" -+#include - - / { - model = "Qualcomm Technologies, Inc. IPQ4019/AP-DK01.1"; -@@ -29,6 +30,32 @@ - }; - - soc { -+ tcsr@194b000 { -+ /* select hostmode */ -+ compatible = "qcom,tcsr"; -+ reg = <0x194b000 0x100>; -+ qcom,usb-hsphy-mode-select = ; -+ status = "okay"; -+ }; -+ -+ ess_tcsr@1953000 { -+ compatible = "qcom,tcsr"; -+ reg = <0x1953000 0x1000>; -+ qcom,ess-interface-select = ; -+ }; -+ -+ tcsr@1949000 { -+ compatible = "qcom,tcsr"; -+ reg = <0x1949000 0x100>; -+ qcom,wifi_glb_cfg = ; -+ }; -+ -+ tcsr@1957000 { -+ compatible = "qcom,tcsr"; -+ reg = <0x1957000 0x100>; -+ qcom,wifi_noc_memtype_m0_m2 = ; -+ }; -+ - rng@22000 { - status = "ok"; - }; -@@ -74,14 +101,6 @@ - pinctrl-names = "default"; - status = "ok"; - cs-gpios = <&tlmm 54 0>; -- -- mx25l25635e@0 { -- #address-cells = <1>; -- #size-cells = <1>; -- reg = <0>; -- compatible = "mx25l25635e"; -- spi-max-frequency = <24000000>; -- }; - }; - - serial@78af000 { -@@ -109,5 +128,41 @@ - wifi@a800000 { - status = "ok"; - }; -+ -+ mdio@90000 { -+ status = "okay"; -+ }; -+ -+ ess-switch@c000000 { -+ status = "okay"; -+ }; -+ -+ ess-psgmii@98000 { -+ status = "okay"; -+ }; -+ -+ edma@c080000 { -+ status = "okay"; -+ }; -+ -+ usb3_ss_phy: ssphy@9a000 { -+ status = "okay"; -+ }; -+ -+ usb3_hs_phy: hsphy@a6000 { -+ status = "okay"; -+ }; -+ -+ usb3: usb3@8af8800 { -+ status = "okay"; -+ }; -+ -+ usb2_hs_phy: hsphy@a8000 { -+ status = "okay"; -+ }; -+ -+ usb2: usb2@60f8800 { -+ status = "okay"; -+ }; - }; - }; ---- a/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1-c1.dts -+++ b/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1-c1.dts -@@ -18,5 +18,73 @@ - - / { - model = "Qualcomm Technologies, Inc. IPQ40xx/AP-DK01.1-C1"; -+ compatible = "qcom,ap-dk01.1-c1", "qcom,ap-dk01.2-c1"; - -+ memory { -+ device_type = "memory"; -+ reg = <0x80000000 0x10000000>; -+ }; -+}; -+ -+&blsp1_spi1 { -+ mx25l25635f@0 { -+ compatible = "mx25l25635f", "jedec,spi-nor"; -+ #address-cells = <1>; -+ #size-cells = <1>; -+ reg = <0>; -+ spi-max-frequency = <24000000>; -+ -+ SBL1@0 { -+ label = "SBL1"; -+ reg = <0x0 0x40000>; -+ read-only; -+ }; -+ MIBIB@40000 { -+ label = "MIBIB"; -+ reg = <0x40000 0x20000>; -+ read-only; -+ }; -+ QSEE@60000 { -+ label = "QSEE"; -+ reg = <0x60000 0x60000>; -+ read-only; -+ }; -+ CDT@c0000 { -+ label = "CDT"; -+ reg = <0xc0000 0x10000>; -+ read-only; -+ }; -+ DDRPARAMS@d0000 { -+ label = "DDRPARAMS"; -+ reg = <0xd0000 0x10000>; -+ read-only; -+ }; -+ APPSBLENV@e0000 { -+ label = "APPSBLENV"; -+ reg = <0xe0000 0x10000>; -+ read-only; -+ }; -+ APPSBL@f0000 { -+ label = "APPSBL"; -+ reg = <0xf0000 0x80000>; -+ read-only; -+ }; -+ ART@170000 { -+ label = "ART"; -+ reg = <0x170000 0x10000>; -+ read-only; -+ }; -+ kernel@180000 { -+ label = "kernel"; -+ reg = <0x180000 0x400000>; -+ }; -+ rootfs@580000 { -+ label = "rootfs"; -+ reg = <0x580000 0x1600000>; -+ }; -+ firmware@180000 { -+ label = "firmware"; -+ reg = <0x180000 0x1a00000>; -+ }; -+ }; - }; diff --git a/target/linux/ipq40xx/patches-5.10/902-dts-ipq4019-ap-dk04.1.patch b/target/linux/ipq40xx/patches-5.10/902-dts-ipq4019-ap-dk04.1.patch deleted file mode 100644 index ca32144846..0000000000 --- a/target/linux/ipq40xx/patches-5.10/902-dts-ipq4019-ap-dk04.1.patch +++ /dev/null @@ -1,167 +0,0 @@ ---- a/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1.dtsi -+++ b/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1.dtsi -@@ -17,53 +17,79 @@ - stdout-path = "serial0:115200n8"; - }; - -- memory { -- device_type = "memory"; -- reg = <0x80000000 0x10000000>; /* 256MB */ -- }; -- - soc { -+ rng@22000 { -+ status = "okay"; -+ }; -+ - pinctrl@1000000 { - serial_0_pins: serial0-pinmux { -- pins = "gpio16", "gpio17"; -- function = "blsp_uart0"; -- bias-disable; -+ mux { -+ pins = "gpio16", "gpio17"; -+ function = "blsp_uart0"; -+ bias-disable; -+ }; - }; - - serial_1_pins: serial1-pinmux { -- pins = "gpio8", "gpio9", -- "gpio10", "gpio11"; -- function = "blsp_uart1"; -- bias-disable; -+ mux { -+ pins = "gpio8", "gpio9"; -+ function = "blsp_uart1"; -+ bias-disable; -+ }; - }; - - spi_0_pins: spi-0-pinmux { - pinmux { - function = "blsp_spi0"; - pins = "gpio13", "gpio14", "gpio15"; -- bias-disable; - }; - pinmux_cs { - function = "gpio"; - pins = "gpio12"; -+ }; -+ pinconf { -+ pins = "gpio13", "gpio14", "gpio15"; -+ drive-strength = <12>; -+ bias-disable; -+ }; -+ pinconf_cs { -+ pins = "gpio12"; -+ drive-strength = <2>; - bias-disable; - output-high; - }; - }; - - i2c_0_pins: i2c-0-pinmux { -- pins = "gpio20", "gpio21"; -- function = "blsp_i2c0"; -- bias-disable; -+ pinmux { -+ function = "blsp_i2c0"; -+ pins = "gpio10", "gpio11"; -+ }; -+ pinconf { -+ pins = "gpio10", "gpio11"; -+ drive-strength = <16>; -+ bias-disable; -+ }; - }; - - nand_pins: nand-pins { -- pins = "gpio53", "gpio55", "gpio56", -- "gpio57", "gpio58", "gpio59", -- "gpio60", "gpio62", "gpio63", -- "gpio64", "gpio65", "gpio66", -- "gpio67", "gpio68", "gpio69"; -- function = "qpic"; -+ pullups { -+ pins = "gpio52", "gpio53", "gpio58", -+ "gpio59"; -+ function = "qpic"; -+ bias-pull-up; -+ }; -+ -+ pulldowns { -+ pins = "gpio54", "gpio55", "gpio56", -+ "gpio57", "gpio60", "gpio61", -+ "gpio62", "gpio63", "gpio64", -+ "gpio65", "gpio66", "gpio67", -+ "gpio68", "gpio69"; -+ function = "qpic"; -+ bias-pull-down; -+ }; - }; - }; - -@@ -89,11 +115,11 @@ - status = "ok"; - cs-gpios = <&tlmm 12 0>; - -- m25p80@0 { -+ mx25l25635e@0 { - #address-cells = <1>; - #size-cells = <1>; - reg = <0>; -- compatible = "n25q128a11"; -+ compatible = "mx25l25635e"; - spi-max-frequency = <24000000>; - }; - }; -@@ -103,9 +129,48 @@ - perst-gpio = <&tlmm 38 0x1>; - }; - -+ i2c0: i2c@78b7000 { /* BLSP1 QUP2 */ -+ pinctrl-0 = <&i2c_0_pins>; -+ pinctrl-names = "default"; -+ -+ status = "okay"; -+ }; -+ - qpic-nand@79b0000 { - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - }; -+ -+ usb3_ss_phy: ssphy@9a000 { -+ status = "okay"; -+ }; -+ -+ usb3_hs_phy: hsphy@a6000 { -+ status = "okay"; -+ }; -+ -+ usb3: usb3@8af8800 { -+ status = "okay"; -+ }; -+ -+ usb2_hs_phy: hsphy@a8000 { -+ status = "okay"; -+ }; -+ -+ usb2: usb2@60f8800 { -+ status = "okay"; -+ }; -+ -+ cryptobam: dma@8e04000 { -+ status = "okay"; -+ }; -+ -+ crypto@8e3a000 { -+ status = "okay"; -+ }; -+ -+ watchdog@b017000 { -+ status = "okay"; -+ }; - }; - }; -- 2.30.2