From 5e33fdfc47eeb3620536baaa1de13fbd2e6b5d62 Mon Sep 17 00:00:00 2001 From: Kristian Skramstad Date: Sun, 1 Oct 2023 16:28:24 +0200 Subject: [PATCH] qualcommax: ipq807x: add support for Netgear WAX630 ``` Specifications: * CPU: Qualcomm IPQ8074A, SoC Version: 2.0, Quad core 1651 MHz * RAM: 1 GiB of DDR3 466 MHz * Flash: NAND 512 MiB (Winbond W29N04GZ) * 6 RGB LEDs: Power, LAN1, LAN2, 2.4GHz, 5GHz H and 5GHz L * UART: One 4-pin populated header next to the heatsink and a chip. GND RXD TXD, beginning from the external antennas. 115200n8. Lan: * One 100/1000/2.5GBASE-T Gigabit Ethernet 802.3bt/at * One 100/1000 Gigabit Ethernet Wlan: * 4x4 in 2.4GHz : 802.11b/g/n/ax * 4x4 in 5.0GHz L: 802.11a/n/ac/ax * 4x4 in 5.0GHz H: 802.11a/n/ac/ax * OFDM and OFDMA * Bidir and MU-MIMO * Internal antenna 2.86/4.41/4.98 dBi (2.4GHz/5GHz L/5GHz H) Power: * 802.3bt/at 30.1W * DC 12V/3.5A Mounting: Wall and ceiling ``` ``` 1. Download the OpenWrt initramfs image. Copy the image to a TFTP server 2. Connect to the console on the AP, and connect the LAN port to your LAN 3. Stop auto boot to get to U-boot shell, interrupt the autoboot process by pressing '0' when prompted 4. Set active_fw in env 4. Set active_fw in env # setenv active_fw 1 5. Transfer the initramfs image with TFTP # setenv serverip 192.168.1.10 (IP of TFTP server host) # setenv ipaddr 192.168.1.1 (IP used by the router for getting the image, must be in the same subnet as the TFTP host) # tftpboot openwrt-qualcommax-ipq807x-netgear_wax630-initramfs-uImage.itb 6. Reboot and load the image # bootm 7. SCP factory image to the AP # scp openwrt-qualcommax-ipq807x-netgear_wax630-squashfs-factory.ubi root@192.168.1.1:/tmp/ 8. Connect to device using SSH (use the LAN port) 9. Flash squashfs-factory.ubi from within the initramfs instance of OpenWRT Before you flash, please check your mtd partitions where mtdX is the right mtd rootfs partition. # cat /proc/mtd (To check MTD partitions) # ubiformat /dev/mtd18 -y -f /tmp/openwrt-qualcommax-ipq807x-netgear_wax630-squashfs-factory.ubi 10. Set active_fw to 0 # /usr/sbin/fw_setenv active_fw 0 11. Reboot the AP and your done # reboot ``` Reviewed-by: Robert Marko Signed-off-by: Kristian Skramstad --- .../uboot-envtools/files/qualcommax_ipq807x | 3 +- .../arm64/boot/dts/qcom/ipq8074-wax630.dts | 253 ++++++++++++++++++ target/linux/qualcommax/image/ipq807x.mk | 25 ++ .../ipq807x/base-files/etc/board.d/01_leds | 4 + .../ipq807x/base-files/etc/board.d/02_network | 3 + .../etc/hotplug.d/firmware/11-ath11k-caldata | 1 + .../base-files/lib/upgrade/platform.sh | 3 +- 7 files changed, 290 insertions(+), 2 deletions(-) create mode 100644 target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8074-wax630.dts diff --git a/package/boot/uboot-envtools/files/qualcommax_ipq807x b/package/boot/uboot-envtools/files/qualcommax_ipq807x index 106ba47c08..761d5dfcc9 100644 --- a/package/boot/uboot-envtools/files/qualcommax_ipq807x +++ b/package/boot/uboot-envtools/files/qualcommax_ipq807x @@ -11,7 +11,8 @@ case "$board" in dynalink,dl-wrx36|\ netgear,rax120v2|\ netgear,wax218|\ -netgear,wax620) +netgear,wax620|\ +netgear,wax630) idx="$(find_mtd_index 0:appsblenv)" [ -n "$idx" ] && \ ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x40000" "0x20000" "2" diff --git a/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8074-wax630.dts b/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8074-wax630.dts new file mode 100644 index 0000000000..f2498837de --- /dev/null +++ b/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8074-wax630.dts @@ -0,0 +1,253 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +/dts-v1/; + +#include "ipq8074.dtsi" +#include "ipq8074-hk-cpu.dtsi" +#include "ipq8074-ess.dtsi" +#include +#include +#include + +/ { + model = "Netgear WAX630"; + compatible = "netgear,wax630", "qcom,ipq8074"; + + aliases { + serial0 = &blsp1_uart5; + + ethernet0 = &dp6_syn; + ethernet1 = &dp4; + label-mac-device = &dp6_syn; + + led-boot = &led_system_blue; + led-failsafe = &led_system_red; + led-running = &led_system_green; + led-upgrade = &led_system_blue; + }; + + chosen { + stdout-path = "serial0:115200n8"; + bootargs-append = " root=/dev/ubiblock0_1"; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&tlmm 54 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + led-spi { + compatible = "spi-gpio"; + #address-cells = <1>; + #size-cells = <0>; + + sck-gpios = <&tlmm 18 GPIO_ACTIVE_HIGH>; + mosi-gpios = <&tlmm 19 GPIO_ACTIVE_HIGH>; + + led_gpio: led-gpio@0 { + compatible = "fairchild,74hc595"; + reg = <0>; + gpio-controller; + #gpio-cells = <2>; + registers-number = <1>; + enable-gpios = <&tlmm 20 GPIO_ACTIVE_HIGH>; + spi-max-frequency = <1000000>; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_system_red: system-red { + label = "system:red"; + gpios = <&tlmm 22 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led_system_green: system-green { + label = "system:green"; + gpios = <&tlmm 38 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led_system_blue: system-blue { + label = "system:blue"; + gpios = <&tlmm 21 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + lan1-green { + label = "lan1:green"; + gpios = <&tlmm 26 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + lan1-orange { + label = "lan1:orange"; + gpios = <&tlmm 27 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + lan2-green { + label = "lan2:green"; + gpios = <&tlmm 57 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + lan2-orange { + label = "lan2:orange"; + gpios = <&tlmm 60 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + 2g-blue { + label = "wlan2g:blue"; + gpios = <&tlmm 29 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + 2g-green { + label = "wlan2g:green"; + gpios = <&tlmm 30 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + 5g-low-blue { + label = "wlan5g_low:blue"; + gpios = <&tlmm 33 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + 5g-low-green { + label = "wlan5g_low:green"; + gpios = <&tlmm 34 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + 5g-high-blue { + label = "wlan5g_high:blue"; + gpios = <&tlmm 31 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + 5g-high-green { + label = "wlan5g_high:green"; + gpios = <&tlmm 32 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + }; +}; + +&edma { + status = "okay"; +}; + +&switch { + status = "okay"; + + switch_cpu_bmp = <0x01>; + switch_lan_bmp = <0x3e>; + switch_wan_bmp = <0x40>; + switch_mac_mode = <0x00>; + switch_mac_mode1 = <0xff>; + switch_mac_mode2 = <0x0d>; + bm_tick_mode = <0x00>; + tm_tick_mode = <0x00>; + + qcom,port_phyinfo { + port@3 { + port_id = <4>; + phy_address = <3>; + }; + + port@5 { + port_id = <6>; + phy_address = <28>; + port_mac_sel = "QGMAC_PORT"; + }; + }; +}; + +&tlmm { + mdio_pins: mdio-pins { + mdc { + pins = "gpio68"; + function = "mdc"; + drive-strength = <8>; + bias-pull-up; + }; + + mdio { + pins = "gpio69"; + function = "mdio"; + drive-strength = <8>; + bias-pull-up; + }; + }; +}; + +&mdio { + status = "okay"; + + pinctrl-0 = <&mdio_pins>; + pinctrl-names = "default"; + reset-gpios = <&tlmm 37 GPIO_ACTIVE_LOW>; + + qca8075: ethernet-phy@3 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <3>; + }; + + qca8081: ethernet-phy@28 { + compatible = "ethernet-phy-id004d.d101"; + reg = <28>; + reset-gpios = <&tlmm 25 GPIO_ACTIVE_LOW>; + }; +}; + +&dp4 { + status = "okay"; + phy-handle = <&qca8075>; + label = "lan2"; +}; + +&dp6_syn { + status = "okay"; + phy-handle = <&qca8081>; + label = "lan1"; +}; + +&qpic_bam { + status = "okay"; +}; + +&qpic_nand { + status = "okay"; + + nand@0 { + reg = <0>; + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + nand-bus-width = <8>; + + partitions { + compatible = "qcom,smem-part"; + }; + }; +}; + +&blsp1_uart5 { + status = "okay"; +}; + +&wifi { + status = "okay"; + + qcom,ath11k-calibration-variant = "Netgear-WAX630"; +}; diff --git a/target/linux/qualcommax/image/ipq807x.mk b/target/linux/qualcommax/image/ipq807x.mk index c0f15f3c83..f288dae6d8 100644 --- a/target/linux/qualcommax/image/ipq807x.mk +++ b/target/linux/qualcommax/image/ipq807x.mk @@ -23,6 +23,16 @@ define Device/UbiFit IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata endef +define Build/wax6xx-netgear-tar + mkdir $@.tmp + mv $@ $@.tmp/nand-ipq807x-apps.img + md5sum $@.tmp/nand-ipq807x-apps.img | cut -c 1-32 > $@.tmp/nand-ipq807x-apps.md5sum + echo $(DEVICE_MODEL) > $@.tmp/metadata.txt + echo $(DEVICE_MODEL)"_V9.9.9.9" > $@.tmp/version + tar -C $@.tmp/ -cf $@ . + rm -rf $@.tmp +endef + define Device/buffalo_wxr-5950ax12 $(call Device/FitImage) DEVICE_VENDOR := Buffalo @@ -146,6 +156,21 @@ define Device/netgear_wax620 endef TARGET_DEVICES += netgear_wax620 +define Device/netgear_wax630 + $(call Device/FitImage) + $(call Device/UbiFit) + DEVICE_VENDOR := Netgear + DEVICE_MODEL := WAX630 + DEVICE_DTS_CONFIG := config@hk01 + BLOCKSIZE := 128k + PAGESIZE := 2048 + SOC := ipq8074 + IMAGES := ui-factory.tar factory.ubi sysupgrade.bin + IMAGE/ui-factory.tar := append-ubi | wax6xx-netgear-tar + DEVICE_PACKAGES += kmod-spi-gpio ipq-wifi-netgear_wax630 +endef +TARGET_DEVICES += netgear_wax630 + define Device/prpl_haze $(call Device/FitImage) $(call Device/EmmcImage) diff --git a/target/linux/qualcommax/ipq807x/base-files/etc/board.d/01_leds b/target/linux/qualcommax/ipq807x/base-files/etc/board.d/01_leds index 3c13fb06a7..fb14a667cb 100644 --- a/target/linux/qualcommax/ipq807x/base-files/etc/board.d/01_leds +++ b/target/linux/qualcommax/ipq807x/base-files/etc/board.d/01_leds @@ -20,6 +20,10 @@ netgear,wax218) netgear,wax620) ucidef_set_led_netdev "lan" "LAN" "lan:green" "lan" ;; +netgear,wax630) + ucidef_set_led_netdev "lan1" "LAN1" "lan1:green" "lan1" + ucidef_set_led_netdev "lan2" "LAN2" "lan2:green" "lan2" + ;; redmi,ax6|\ xiaomi,ax3600) ucidef_set_led_netdev "wan" "WAN" "blue:network" "wan" diff --git a/target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network b/target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network index ad8e34e9fe..11101794c3 100644 --- a/target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network +++ b/target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network @@ -29,6 +29,9 @@ ipq807x_setup_interfaces() netgear,wax620) ucidef_set_interface_lan "lan" "dhcp" ;; + netgear,wax630) + ucidef_set_interface_lan "lan1 lan2" "dhcp" + ;; prpl,haze) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" "wan" ;; diff --git a/target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata b/target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata index cba1f84b7f..394c22d021 100644 --- a/target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata +++ b/target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata @@ -17,6 +17,7 @@ case "$FIRMWARE" in netgear,rax120v2|\ netgear,wax218|\ netgear,wax620|\ + netgear,wax630|\ qnap,301w|\ redmi,ax6|\ xiaomi,ax3600|\ diff --git a/target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh b/target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh index 90ebff17d4..e2c713c3db 100644 --- a/target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh +++ b/target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh @@ -70,7 +70,8 @@ platform_do_upgrade() { edimax,cax1800|\ netgear,rax120v2|\ netgear,wax218|\ - netgear,wax620) + netgear,wax620|\ + netgear,wax630) nand_do_upgrade "$1" ;; prpl,haze|\ -- 2.30.2