From 4f86edf477edbc0f20b5a49a69f658fa82158284 Mon Sep 17 00:00:00 2001 From: Sander Vanheule Date: Tue, 7 Jul 2020 18:04:37 +0200 Subject: [PATCH] ath79: support for TP-Link EAP225-Outdoor v1 MIME-Version: 1.0 Content-Type: text/plain; charset=utf8 Content-Transfer-Encoding: 8bit TP-Link EAP225-Outdoor v1 is an AC1200 (802.11ac Wave-2) pole or wall mount access point. Debricking requires access to the serial port, which is non-trivial. Device specifications: * SoC: QCA9563 @ 775MHz * Memory: 128MiB DDR2 * Flash: 16MiB SPI-NOR * Wireless 2.4GHz (SoC): b/g/n 2x2 * Wireless 5GHz (QCA9886): a/n/ac 2x2 MU-MIMO * Ethernet (AR8033): 1× 1GbE, PoE Flashing instructions: * ssh into target device with recent (>= v1.6.0) firmware * run `cliclientd stopcs` on target device * upload factory image via web interface Debricking: To recover the device, you need access to the serial port. This requires fine soldering to test points, or the use of probe pins. * Open the case and solder wires to the test points: RXD, TXD and TPGND4 * Use a 3.3V UART, 115200 baud, 8n1 * Interrupt bootloader by holding ctrl+B during boot * upload initramfs via built-in tftp client and perform sysupgrade setenv ipaddr 192.168.1.1 # default, change as required setenv serverip 192.168.1.10 # default, change as required tftp 0x80800000 initramfs.bin bootelf $fileaddr MAC addresses: MAC address (as on device label) is stored in device info partition at an offset of 8 bytes. ath9k device has same address as ethernet, ath10k uses address incremented by 1. From stock ifconfig: ath0 Link encap:Ethernet HWaddr D8:...:2E ath10 Link encap:Ethernet HWaddr D8:...:2F br0 Link encap:Ethernet HWaddr D8:...:2E eth0 Link encap:Ethernet HWaddr D8:...:2E Tested by forum user PolynomialDivision on firmware v1.7.0. UART access tested by forum user arinc9. Signed-off-by: Sander Vanheule --- .../dts/qca9563_tplink_eap225-outdoor-v1.dts | 30 +++++++++++++++++++ .../generic/base-files/etc/board.d/02_network | 1 + .../etc/hotplug.d/firmware/11-ath10k-caldata | 1 + target/linux/ath79/image/generic-tp-link.mk | 11 +++++++ tools/firmware-utils/src/tplink-safeloader.c | 29 ++++++++++++++++++ 5 files changed, 72 insertions(+) create mode 100644 target/linux/ath79/dts/qca9563_tplink_eap225-outdoor-v1.dts diff --git a/target/linux/ath79/dts/qca9563_tplink_eap225-outdoor-v1.dts b/target/linux/ath79/dts/qca9563_tplink_eap225-outdoor-v1.dts new file mode 100644 index 000000000000..fc6d3365a071 --- /dev/null +++ b/target/linux/ath79/dts/qca9563_tplink_eap225-outdoor-v1.dts @@ -0,0 +1,30 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qca9563_tplink_eap2x5-1port.dtsi" + +/ { + compatible = "tplink,eap225-outdoor-v1", "qca,qca9563"; + model = "TP-Link EAP225-Outdoor v1"; + + aliases { + led-boot = &led_status_green; + led-failsafe = &led_status_amber; + led-running = &led_status_green; + led-upgrade = &led_status_amber; + }; + + leds { + compatible = "gpio-leds"; + + led_status_green: status_green { + label = "green:status"; + gpios = <&gpio 7 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + + led_status_amber: status_amber { + label = "amber:status"; + gpios = <&gpio 9 GPIO_ACTIVE_LOW>; + }; + }; +}; diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network index c29c4006c80a..928b6c8903ed 100755 --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network @@ -48,6 +48,7 @@ ath79_setup_interfaces() tplink,cpe510-v3|\ tplink,cpe610-v1|\ tplink,cpe610-v2|\ + tplink,eap225-outdoor-v1|\ tplink,eap245-v1|\ tplink,re350k-v1|\ tplink,re355-v1|\ diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 5229ad17f4e4..5be1c72ab0ab 100644 --- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -208,6 +208,7 @@ case "$FIRMWARE" in ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \ /lib/firmware/ath10k/QCA9888/hw2.0/board.bin ;; + tplink,eap225-outdoor-v1|\ tplink,eap225-wall-v2|\ tplink,tl-wpa8630p-v2-int|\ tplink,tl-wpa8630p-v2.0-eu|\ diff --git a/target/linux/ath79/image/generic-tp-link.mk b/target/linux/ath79/image/generic-tp-link.mk index c704d99c98e0..343ea963c372 100644 --- a/target/linux/ath79/image/generic-tp-link.mk +++ b/target/linux/ath79/image/generic-tp-link.mk @@ -371,6 +371,17 @@ define Device/tplink-eap2x5 pad-extra 128 endef +define Device/tplink_eap225-outdoor-v1 + $(Device/tplink-eap2x5) + SOC := qca9563 + IMAGE_SIZE := 13824k + DEVICE_MODEL := EAP225-Outdoor + DEVICE_VARIANT := v1 + DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct + TPLINK_BOARD_ID := EAP225-OUTDOOR-V1 +endef +TARGET_DEVICES += tplink_eap225-outdoor-v1 + define Device/tplink_eap225-wall-v2 $(Device/tplink-eap2x5) SOC := qca9561 diff --git a/tools/firmware-utils/src/tplink-safeloader.c b/tools/firmware-utils/src/tplink-safeloader.c index 2657b2c928e6..4389cf034622 100644 --- a/tools/firmware-utils/src/tplink-safeloader.c +++ b/tools/firmware-utils/src/tplink-safeloader.c @@ -1298,6 +1298,35 @@ static struct device_info boards[] = { .last_sysupgrade_partition = "file-system" }, + /** Firmware layout for the EAP225-Outdoor v1 */ + { + .id = "EAP225-OUTDOOR-V1", + .support_list = + "SupportList:\r\n" + "EAP225-Outdoor(TP-Link|UN|AC1200-D):1.0\r\n", + .support_trail = '\xff', + .soft_ver = NULL, + .soft_ver_compat_level = 1, + + .partitions = { + {"fs-uboot", 0x00000, 0x20000}, + {"partition-table", 0x20000, 0x02000}, + {"default-mac", 0x30000, 0x01000}, + {"support-list", 0x31000, 0x00100}, + {"product-info", 0x31100, 0x00400}, + {"soft-version", 0x32000, 0x00100}, + {"firmware", 0x40000, 0xd80000}, + {"user-config", 0xdc0000, 0x30000}, + {"mutil-log", 0xf30000, 0x80000}, + {"oops", 0xfb0000, 0x40000}, + {"radio", 0xff0000, 0x10000}, + {NULL, 0, 0} + }, + + .first_sysupgrade_partition = "os-image", + .last_sysupgrade_partition = "file-system" + }, + /** Firmware layout for the EAP225-Wall v2 */ { .id = "EAP225-WALL-V2", -- 2.30.2