From 4cdad5f43ae67e4ceeac69ef4af4392bd2f7381f Mon Sep 17 00:00:00 2001 From: Peter Tyser Date: Fri, 17 Jul 2009 19:01:13 -0500 Subject: [PATCH] xpedite1k: Sync organization of board config with other X-ES boards This change should have no functional effect Signed-off-by: Peter Tyser Signed-off-by: Stefan Roese --- include/configs/XPEDITE1K.h | 159 +++++++++++++++++++----------------- 1 file changed, 85 insertions(+), 74 deletions(-) diff --git a/include/configs/XPEDITE1K.h b/include/configs/XPEDITE1K.h index c67350af2e..391d0419fa 100644 --- a/include/configs/XPEDITE1K.h +++ b/include/configs/XPEDITE1K.h @@ -38,26 +38,40 @@ #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ #define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ -/* POST support */ -#define CONFIG_POST (CONFIG_SYS_POST_RTC | \ - CONFIG_SYS_POST_I2C) +/* + * DDR config + */ +#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for setup */ +#define SPD_EEPROM_ADDRESS {0x54} /* SPD i2c spd addresses */ +#define CONFIG_VERY_BIG_RAM 1 /* * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */ -#define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of FLASH */ - -#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ -#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */ -#define CONFIG_SYS_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */ -#define CONFIG_SYS_ISRAM_BASE 0xc0000000 /* internal SRAM */ -#define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */ - +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of FLASH */ +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ +#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */ +#define CONFIG_SYS_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */ +#define CONFIG_SYS_ISRAM_BASE 0xc0000000 /* internal SRAM */ +#define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */ #define CONFIG_SYS_NVRAM_BASE_ADDR (CONFIG_SYS_PERIPHERAL_BASE + 0x08000000) #define CONFIG_SYS_GPIO_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x00000700) +/* + * Diagnostics + */ +#define CONFIG_SYS_MEMTEST_START 0x0400000 +#define CONFIG_SYS_MEMTEST_END 0x0C00000 + +/* POST support */ +#define CONFIG_POST (CONFIG_SYS_POST_RTC | \ + CONFIG_SYS_POST_I2C) + +/* + * LED support + */ #define USR_LED0 0x00000080 #define USR_LED1 0x00000100 #define USR_LED2 0x00000200 @@ -78,13 +92,14 @@ extern void out32(unsigned int, unsigned long); #define LED3_OFF() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) | USR_LED3)) #endif -/* Initial RAM & stack pointer (placed in internal SRAM) */ +/* + * Use internal SRAM for initial stack + */ #define CONFIG_SYS_TEMP_STACK_OCM 1 #define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_ISRAM_BASE #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_ISRAM_BASE /* Initial RAM address */ #define CONFIG_SYS_INIT_RAM_END 0x2000 /* End of used area in RAM */ #define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ - #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) #define CONFIG_SYS_POST_WORD_ADDR (CONFIG_SYS_GBL_DATA_OFFSET - 0x4) #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_POST_WORD_ADDR @@ -92,19 +107,17 @@ extern void out32(unsigned int, unsigned long); #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ #define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc */ -/* Serial Port */ -#undef CONFIG_SERIAL_SOFTWARE_FIFO -#define CONFIG_BAUDRATE 9600 +/* + * Serial Port + */ #define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400} - -/* RTC: STMicro M41T00 */ -#define CONFIG_RTC_M41T11 1 -#define CONFIG_SYS_I2C_RTC_ADDR 0x68 -#define CONFIG_SYS_M41T11_BASE_YEAR 2000 +#define CONFIG_BAUDRATE 9600 +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ /* - * FLASH related + * NOR flash configuration */ #define CONFIG_SYS_MAX_FLASH_BANKS 3 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, 0xf0000000, 0xf4000000 } @@ -118,45 +131,54 @@ extern void out32(unsigned int, unsigned long); #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ -/* DDR SDRAM */ -#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for setup */ -#define SPD_EEPROM_ADDRESS {0x54} /* SPD i2c spd addresses */ -#define CONFIG_VERY_BIG_RAM 1 - -/* I2C */ +/* + * I2C + */ #define CONFIG_HARD_I2C 1 /* I2C with hardware support */ #define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ #define CONFIG_SYS_I2C_SLAVE 0x7f #define CONFIG_SYS_I2C_NOPROBES {0x55,0x56,0x57,0x58,0x59,0x5a,0x5b,0x5c,0x69} -/* - * Environment Configuration - */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k (one sector) for env */ -#define CONFIG_ENV_SIZE 0x8000 -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - (256 * 1024)) - -/* EEPROM */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 +/* I2C EEPROM */ +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ +/* I2C RTC: STMicro M41T00 */ +#define CONFIG_RTC_M41T11 1 +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 +#define CONFIG_SYS_M41T11_BASE_YEAR 2000 + +/* + * PCI + */ +/* General PCI */ +#define CONFIG_PCI /* include pci support */ +#define CONFIG_PCI_PNP /* do pci plug-and-play */ +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE */ + +/* Board-specific PCI */ +#define CONFIG_SYS_PCI_TARGET_INIT /* let board init pci target */ +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014 /* IBM */ +#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ +#define CONFIG_SYS_PCI_FORCE_PCI_CONV /* Force PCI Conventional Mode */ +/* + * Networking options + */ #define CONFIG_PPC4xx_EMAC -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_PHY_ADDR 4 /* PHY address phy0 not populated */ -#define CONFIG_PHY2_ADDR 4 /* PHY address phy2 */ -#define CONFIG_PHY3_ADDR 8 /* PHY address phy3 */ -#define CONFIG_NET_MULTI 1 #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ +#define CONFIG_NET_MULTI 1 +#define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ #define CONFIG_SYS_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ - +#define CONFIG_ETHPRIME "ppc_4xx_eth2" +#define CONFIG_PHY_ADDR 4 /* PHY address phy0 not populated */ +#define CONFIG_PHY2_ADDR 4 /* PHY address phy2 */ #define CONFIG_HAS_ETH2 1 /* add support for "eth2addr" */ +#define CONFIG_PHY3_ADDR 8 /* PHY address phy3 */ #define CONFIG_HAS_ETH3 1 /* add support for "eth3addr" */ /* BOOTP options */ @@ -166,7 +188,7 @@ extern void out32(unsigned int, unsigned long); #define CONFIG_BOOTP_HOSTNAME /* - * Command line configuration + * Command configuration */ #include @@ -175,7 +197,6 @@ extern void out32(unsigned int, unsigned long); #define CONFIG_CMD_DHCP #define CONFIG_CMD_EEPROM #define CONFIG_CMD_ELF -#define CONFIG_CMD_SAVEENV #define CONFIG_CMD_FLASH #define CONFIG_CMD_I2C #define CONFIG_CMD_IRQ @@ -184,14 +205,14 @@ extern void out32(unsigned int, unsigned long); #define CONFIG_CMD_NET #define CONFIG_CMD_PCI #define CONFIG_CMD_PING +#define CONFIG_CMD_SAVEENV #define CONFIG_CMD_SNTP -#undef CONFIG_WATCHDOG /* watchdog disabled */ - /* * Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ @@ -201,29 +222,8 @@ extern void out32(unsigned int, unsigned long); #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ -#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ - -/* - * PCI - */ -/* General PCI */ -#define CONFIG_PCI /* include pci support */ -#define CONFIG_PCI_PNP /* do pci plug-and-play */ -#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE */ - -/* Board-specific PCI */ -#define CONFIG_SYS_PCI_TARGET_INIT /* let board init pci target */ -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014 /* IBM */ -#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ -#define CONFIG_SYS_PCI_FORCE_PCI_CONV /* Force PCI Conventional Mode */ +#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ /* * For booting Linux, the board info and command line data @@ -233,16 +233,27 @@ extern void out32(unsigned int, unsigned long); #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /* - * Internal Definitions + * Boot Flags */ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ +/* + * KGDB configuration + */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif +/* + * Environment Configuration + */ +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k (one sector) for env */ +#define CONFIG_ENV_SIZE 0x8000 +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - (256 * 1024)) + /* * Flash memory map: * fff80000 - ffffffff U-Boot (512 KB) -- 2.30.2