From 4a3afb73cdeaec0b4d4b39b6af0968cfa804b662 Mon Sep 17 00:00:00 2001 From: Padmavathi Venna Date: Tue, 18 Jun 2013 00:02:31 +0900 Subject: [PATCH] ARM: dts: Update Samsung I2S documentation This patch updates the samsung i2s documentation for pinmux and clock entries. Signed-off-by: Padmavathi Venna Signed-off-by: Kukjin Kim --- .../devicetree/bindings/sound/samsung-i2s.txt | 46 ++++++++----------- 1 file changed, 19 insertions(+), 27 deletions(-) diff --git a/Documentation/devicetree/bindings/sound/samsung-i2s.txt b/Documentation/devicetree/bindings/sound/samsung-i2s.txt index 3070046da2e5..025e66b85a43 100644 --- a/Documentation/devicetree/bindings/sound/samsung-i2s.txt +++ b/Documentation/devicetree/bindings/sound/samsung-i2s.txt @@ -8,6 +8,16 @@ Required SoC Specific Properties: - dmas: list of DMA controller phandle and DMA request line ordered pairs. - dma-names: identifier string for each DMA request line in the dmas property. These strings correspond 1:1 with the ordered pairs in dmas. +- clocks: Handle to iis clock and RCLK source clk. +- clock-names: + i2s0 uses some base clks from CMU and some are from audio subsystem internal + clock controller. The clock names for i2s0 should be "iis", "i2s_opclk0" and + "i2s_opclk1" as shown in the example below. + i2s1 and i2s2 uses clocks from CMU. The clock names for i2s1 and i2s2 should + be "iis" and "i2s_opclk0". + "iis" is the i2s bus clock and i2s_opclk0, i2s_opclk1 are sources of the root + clk. i2s0 has internal mux to select the source of root clk and i2s1 and i2s2 + doesn't have any such mux. Optional SoC Specific Properties: @@ -20,44 +30,26 @@ Optional SoC Specific Properties: then this flag is enabled. - samsung,idma-addr: Internal DMA register base address of the audio sub system(used in secondary sound source). - -Required Board Specific Properties: - -- gpios: The gpio specifier for data out,data in, LRCLK, CDCLK and SCLK - interface lines. The format of the gpio specifier depends on the gpio - controller. - The syntax of samsung gpio specifier is - <[phandle of the gpio controller node] - [pin number within the gpio controller] - [mux function] - [flags and pull up/down] - [drive strength]> +- pinctrl-0: Should specify pin control groups used for this controller. +- pinctrl-names: Should contain only one value - "default". Example: -- SoC Specific Portion: - -i2s@03830000 { +i2s0: i2s@03830000 { compatible = "samsung,i2s-v5"; reg = <0x03830000 0x100>; dmas = <&pdma0 10 &pdma0 9 &pdma0 8>; dma-names = "tx", "rx", "tx-sec"; + clocks = <&clock_audss EXYNOS_I2S_BUS>, + <&clock_audss EXYNOS_I2S_BUS>, + <&clock_audss EXYNOS_SCLK_I2S>; + clock-names = "iis", "i2s_opclk0", "i2s_opclk1"; samsung,supports-6ch; samsung,supports-rstclr; samsung,supports-secdai; samsung,idma-addr = <0x03000000>; -}; - -- Board Specific Portion: - -i2s@03830000 { - gpios = <&gpz 0 2 0 0>, /* I2S_0_SCLK */ - <&gpz 1 2 0 0>, /* I2S_0_CDCLK */ - <&gpz 2 2 0 0>, /* I2S_0_LRCK */ - <&gpz 3 2 0 0>, /* I2S_0_SDI */ - <&gpz 4 2 0 0>, /* I2S_0_SDO[1] */ - <&gpz 5 2 0 0>, /* I2S_0_SDO[2] */ - <&gpz 6 2 0 0>; /* I2S_0_SDO[3] */ + pinctrl-names = "default"; + pinctrl-0 = <&i2s0_bus>; }; -- 2.30.2