From 4516ff816084605990115d127df97950c23e389c Mon Sep 17 00:00:00 2001 From: York Sun Date: Thu, 19 Mar 2015 09:30:28 -0700 Subject: [PATCH] driver/ddr/fsl: Add built-in memory test for DDR4 driver Add built-in memory test to catch errors after DDR is initialized, before any other transactions. To enable this test, define CONFIG_FSL_DDR_BIST. An environmental variable "ddr_bist" is checked before starting test. It takes a while (several seconds) depending on system memory size. Signed-off-by: York Sun --- README | 3 ++ drivers/ddr/fsl/fsl_ddr_gen4.c | 73 ++++++++++++++++++++++++++++++++++ 2 files changed, 76 insertions(+) diff --git a/README b/README index d33f3b5fef..f5a719db9d 100644 --- a/README +++ b/README @@ -4884,6 +4884,9 @@ Low Level (hardware related) configuration options: - CONFIG_FSL_DDR_SYNC_REFRESH Enable sync of refresh for multiple controllers. +- CONFIG_FSL_DDR_BIST + Enable built-in memory test for Freescale DDR controllers. + - CONFIG_SYS_83XX_DDR_USES_CS0 Only for 83xx systems. If specified, then DDR should be configured using CS0 and CS1 instead of CS2 and CS3. diff --git a/drivers/ddr/fsl/fsl_ddr_gen4.c b/drivers/ddr/fsl/fsl_ddr_gen4.c index d9fce7d2f3..1d67983065 100644 --- a/drivers/ddr/fsl/fsl_ddr_gen4.c +++ b/drivers/ddr/fsl/fsl_ddr_gen4.c @@ -36,6 +36,13 @@ void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs, defined(CONFIG_SYS_FSL_ERRATUM_A008514) u32 *eddrtqcr1; #endif +#ifdef CONFIG_FSL_DDR_BIST + u32 mtcr, err_detect, err_sbe; + u32 cs0_bnds, cs1_bnds, cs2_bnds, cs3_bnds, cs0_config; +#endif +#ifdef CONFIG_FSL_DDR_BIST + char buffer[CONFIG_SYS_CBSIZE]; +#endif switch (ctrl_num) { case 0: @@ -309,4 +316,70 @@ step2: ddr_out32(&ddr->sdram_cfg_2, temp_sdram_cfg); } #endif + +#ifdef CONFIG_FSL_DDR_BIST +#define BIST_PATTERN1 0xFFFFFFFF +#define BIST_PATTERN2 0x0 +#define BIST_CR 0x80010000 +#define BIST_CR_EN 0x80000000 +#define BIST_CR_STAT 0x00000001 +#define CTLR_INTLV_MASK 0x20000000 + /* Perform build-in test on memory. Three-way interleaving is not yet + * supported by this code. */ + if (getenv_f("ddr_bist", buffer, CONFIG_SYS_CBSIZE) >= 0) { + puts("Running BIST test. This will take a while..."); + cs0_config = ddr_in32(&ddr->cs0_config); + if (cs0_config & CTLR_INTLV_MASK) { + cs0_bnds = ddr_in32(&cs0_bnds); + cs1_bnds = ddr_in32(&cs1_bnds); + cs2_bnds = ddr_in32(&cs2_bnds); + cs3_bnds = ddr_in32(&cs3_bnds); + /* set bnds to non-interleaving */ + ddr_out32(&cs0_bnds, (cs0_bnds & 0xfffefffe) >> 1); + ddr_out32(&cs1_bnds, (cs1_bnds & 0xfffefffe) >> 1); + ddr_out32(&cs2_bnds, (cs2_bnds & 0xfffefffe) >> 1); + ddr_out32(&cs3_bnds, (cs3_bnds & 0xfffefffe) >> 1); + } + ddr_out32(&ddr->mtp1, BIST_PATTERN1); + ddr_out32(&ddr->mtp2, BIST_PATTERN1); + ddr_out32(&ddr->mtp3, BIST_PATTERN2); + ddr_out32(&ddr->mtp4, BIST_PATTERN2); + ddr_out32(&ddr->mtp5, BIST_PATTERN1); + ddr_out32(&ddr->mtp6, BIST_PATTERN1); + ddr_out32(&ddr->mtp7, BIST_PATTERN2); + ddr_out32(&ddr->mtp8, BIST_PATTERN2); + ddr_out32(&ddr->mtp9, BIST_PATTERN1); + ddr_out32(&ddr->mtp10, BIST_PATTERN2); + mtcr = BIST_CR; + ddr_out32(&ddr->mtcr, mtcr); + timeout = 100; + while (timeout > 0 && (mtcr & BIST_CR_EN)) { + mdelay(1000); + timeout--; + mtcr = ddr_in32(&ddr->mtcr); + } + if (timeout <= 0) + puts("Timeout\n"); + else + puts("Done\n"); + err_detect = ddr_in32(&ddr->err_detect); + err_sbe = ddr_in32(&ddr->err_sbe); + if (mtcr & BIST_CR_STAT) { + printf("BIST test failed on controller %d.\n", + ctrl_num); + } + if (err_detect || (err_sbe & 0xffff)) { + printf("ECC error detected on controller %d.\n", + ctrl_num); + } + + if (cs0_config & CTLR_INTLV_MASK) { + /* restore bnds registers */ + ddr_out32(&cs0_bnds, cs0_bnds); + ddr_out32(&cs1_bnds, cs1_bnds); + ddr_out32(&cs2_bnds, cs2_bnds); + ddr_out32(&cs3_bnds, cs3_bnds); + } + } +#endif } -- 2.30.2