From 43e8c37cb4da64a12a3cb88a84b19db7f2fc640c Mon Sep 17 00:00:00 2001 From: David Bauer Date: Sat, 13 Apr 2019 00:05:47 +0200 Subject: [PATCH] ramips: add support for GL.iNet VIXMINI Hardware -------- SoC: MediaTek MT7628NN RAM: 64M DDR2 (Etron EM68B16CWQD-25H) FLASH: 8M (Winbond W25Q64JVSIQ) LED: Power - WLAN BTN: Reset UART: 115200 8N1 TX and RX are labled on the board as pads next to the SoC Installation via web-interface ------------------------------ 1. Visit the web-interface at 192.168.8.1 Note: The ethernet port is by default WAN. So you need to connect to the router via WiFi 2. Navigate to the Update tab on the left side. 3. Select "Local Update" 4. Upload the OpenWrt sysupgrade image. Note: Make sure you select not to preserve the configuration. Installation via U-Boot ----------------------- 1. Hold down the reset button while powering on the device. Wait for the LED to flash 5 times. 2. Assign yourself a static IPv4 in 192.168.1.0/24 3. Upload the OpenWrt sysupgrade image at 192.168.1.1. Signed-off-by: David Bauer --- .../ramips/base-files/etc/board.d/02_network | 1 + target/linux/ramips/dts/VIXMINI.dts | 114 ++++++++++++++++++ target/linux/ramips/image/mt76x8.mk | 8 ++ 3 files changed, 123 insertions(+) create mode 100644 target/linux/ramips/dts/VIXMINI.dts diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network index 5fcf437fbd..89cdf57b3e 100755 --- a/target/linux/ramips/base-files/etc/board.d/02_network +++ b/target/linux/ramips/base-files/etc/board.d/02_network @@ -367,6 +367,7 @@ ramips_setup_interfaces() "0:lan:4" "1:lan:3" "2:lan:2" "3:lan:1" "5:wan" "6@eth0" ;; dlink,dir-510l|\ + glinet,vixmini|\ netgear,ex6150|\ re350-v1) ucidef_add_switch "switch0" \ diff --git a/target/linux/ramips/dts/VIXMINI.dts b/target/linux/ramips/dts/VIXMINI.dts new file mode 100644 index 0000000000..5a52fe2a1b --- /dev/null +++ b/target/linux/ramips/dts/VIXMINI.dts @@ -0,0 +1,114 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include "mt7628an.dtsi" + +#include +#include + +/{ + compatible = "glinet,vixmini", "mediatek,mt7628an-soc"; + model = "GL.iNet VIXMINI"; + + aliases { + led-boot = &led_power; + led-failsafe = &led_power; + led-running = &led_power; + led-upgrade = &led_power; + }; + + chosen { + bootargs = "console=ttyS0,115200"; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x4000000>; + }; + + leds { + compatible = "gpio-leds"; + + led_power: power { + label = "vixmini:blue:power"; + default-state = "on"; + gpios = <&gpio1 10 GPIO_ACTIVE_LOW>; + }; + + wlan { + label = "vixmini:white:wlan"; + gpios = <&gpio1 12 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + }; + + keys { + compatible = "gpio-keys-polled"; + poll-interval = <20>; + + reset { + label = "reset"; + gpios = <&gpio1 6 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; +}; + +&pinctrl { + state_default: pinctrl0 { + gpio { + ralink,group = "wdt", "wled_an", "p1led_an"; + ralink,function = "gpio"; + }; + }; +}; + +ðernet { + mtd-mac-address = <&factory 0x4>; +}; + +&wmac { + status = "okay"; + + ralink,mtd-eeprom = <&factory 0x0>; +}; + +&spi0 { + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <10000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x30000>; + read-only; + }; + + partition@30000 { + label = "u-boot-env"; + reg = <0x30000 0x10000>; + read-only; + }; + + factory: partition@40000 { + label = "factory"; + reg = <0x40000 0x10000>; + read-only; + }; + + partition@50000 { + compatible = "denx,uimage"; + label = "firmware"; + reg = <0x50000 0x7b0000>; + }; + }; + }; +}; diff --git a/target/linux/ramips/image/mt76x8.mk b/target/linux/ramips/image/mt76x8.mk index cb8f181955..02b03e5007 100644 --- a/target/linux/ramips/image/mt76x8.mk +++ b/target/linux/ramips/image/mt76x8.mk @@ -66,6 +66,14 @@ define Device/gl-mt300n-v2 endef TARGET_DEVICES += gl-mt300n-v2 +define Device/glinet_vixmini + DTS := VIXMINI + IMAGE_SIZE := 7872k + DEVICE_TITLE := GL.iNet VIXMINI + SUPPORTED_DEVICES += vixmini +endef +TARGET_DEVICES += glinet_vixmini + define Device/hc5661a DTS := HC5661A IMAGE_SIZE := $(ralink_default_fw_size_16M) -- 2.30.2