From 3f4e6f7b9175e2914b82134c4a6a02825f4766db Mon Sep 17 00:00:00 2001 From: Srinivas Kandagatla Date: Mon, 2 Jun 2014 10:09:55 +0100 Subject: [PATCH] mmc: mmci: add explicit clk control On Controllers like Qcom SD card controller where cclk is mclk and mclk should be directly controlled by the driver. This patch adds support to control mclk directly in the driver, and also adds explicit_mclk_control flag in variant structure giving more flexibility to the driver. Signed-off-by: Srinivas Kandagatla Reviewed-by: Linus Walleij [Ulf Hansson] Fixed checkpatch warning Signed-off-by: Ulf Hansson --- drivers/mmc/host/mmci.c | 29 ++++++++++++++++++++++++++--- drivers/mmc/host/mmci.h | 2 ++ 2 files changed, 28 insertions(+), 3 deletions(-) diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c index b588810fd1a4..2e6075fdce46 100644 --- a/drivers/mmc/host/mmci.c +++ b/drivers/mmc/host/mmci.c @@ -72,6 +72,7 @@ static unsigned int fmax = 515633; * @pwrreg_clkgate: MMCIPOWER register must be used to gate the clock * @busy_detect: true if busy detection on dat0 is supported * @pwrreg_nopower: bits in MMCIPOWER don't controls ext. power supply + * @explicit_mclk_control: enable explicit mclk control in driver. */ struct variant_data { unsigned int clkreg; @@ -93,6 +94,7 @@ struct variant_data { bool pwrreg_clkgate; bool busy_detect; bool pwrreg_nopower; + bool explicit_mclk_control; }; static struct variant_data variant_arm = { @@ -286,7 +288,9 @@ static void mmci_set_clkreg(struct mmci_host *host, unsigned int desired) host->cclk = 0; if (desired) { - if (desired >= host->mclk) { + if (variant->explicit_mclk_control) { + host->cclk = host->mclk; + } else if (desired >= host->mclk) { clk = MCI_CLK_BYPASS; if (variant->st_clkdiv) clk |= MCI_ST_UX500_NEG_EDGE; @@ -1327,6 +1331,17 @@ static void mmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) if (!ios->clock && variant->pwrreg_clkgate) pwr &= ~MCI_PWR_ON; + if (host->variant->explicit_mclk_control && + ios->clock != host->clock_cache) { + ret = clk_set_rate(host->clk, ios->clock); + if (ret < 0) + dev_err(mmc_dev(host->mmc), + "Error setting clock rate (%d)\n", ret); + else + host->mclk = clk_get_rate(host->clk); + } + host->clock_cache = ios->clock; + spin_lock_irqsave(&host->lock, flags); mmci_set_clkreg(host, ios->clock); @@ -1502,9 +1517,12 @@ static int mmci_probe(struct amba_device *dev, * The ARM and ST versions of the block have slightly different * clock divider equations which means that the minimum divider * differs too. + * on Qualcomm like controllers get the nearest minimum clock to 100Khz */ if (variant->st_clkdiv) mmc->f_min = DIV_ROUND_UP(host->mclk, 257); + else if (variant->explicit_mclk_control) + mmc->f_min = clk_round_rate(host->clk, 100000); else mmc->f_min = DIV_ROUND_UP(host->mclk, 512); /* @@ -1514,9 +1532,14 @@ static int mmci_probe(struct amba_device *dev, * the block, of course. */ if (mmc->f_max) - mmc->f_max = min(host->mclk, mmc->f_max); + mmc->f_max = variant->explicit_mclk_control ? + min(variant->f_max, mmc->f_max) : + min(host->mclk, mmc->f_max); else - mmc->f_max = min(host->mclk, fmax); + mmc->f_max = variant->explicit_mclk_control ? + fmax : min(host->mclk, fmax); + + dev_dbg(mmc_dev(mmc), "clocking block at %u Hz\n", mmc->f_max); /* Get regulators and the supported OCR mask */ diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h index d38a99df1820..ef346170b241 100644 --- a/drivers/mmc/host/mmci.h +++ b/drivers/mmc/host/mmci.h @@ -208,6 +208,8 @@ struct mmci_host { spinlock_t lock; unsigned int mclk; + /* cached value of requested clk in set_ios */ + unsigned int clock_cache; unsigned int cclk; u32 pwr_reg; u32 pwr_reg_add; -- 2.30.2