From 3ec2a2b80f3eb53851fe4cef9e65b5d33376ef89 Mon Sep 17 00:00:00 2001 From: Bruce Allan Date: Tue, 2 Jun 2009 11:28:39 +0000 Subject: [PATCH] e1000e: correct flow control thresholds The flow control thresholds, i.e. high and low watermarks of the Rx FIFO for when the hardware should transmit PAUSE frames (XON and XOFF, respectively), need to be tuned for more efficient use of the FIFO. The logic to set the thresholds for parts that support early-receive (ERT) was also wrong in that it should check whether jumbo frames are in use. Signed-off-by: Bruce Allan Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/e1000e/defines.h | 2 ++ drivers/net/e1000e/netdev.c | 14 ++++++++------ 2 files changed, 10 insertions(+), 6 deletions(-) diff --git a/drivers/net/e1000e/defines.h b/drivers/net/e1000e/defines.h index 243aa499fe90..9acfecddb273 100644 --- a/drivers/net/e1000e/defines.h +++ b/drivers/net/e1000e/defines.h @@ -469,6 +469,8 @@ #define AUTO_READ_DONE_TIMEOUT 10 /* Flow Control */ +#define E1000_FCRTH_RTH 0x0000FFF8 /* Mask Bits[15:3] for RTH */ +#define E1000_FCRTL_RTL 0x0000FFF8 /* Mask Bits[15:3] for RTL */ #define E1000_FCRTL_XONE 0x80000000 /* Enable XON frame transmission */ /* Transmit Configuration Word */ diff --git a/drivers/net/e1000e/netdev.c b/drivers/net/e1000e/netdev.c index 7e412d1168ed..b7a46c513783 100644 --- a/drivers/net/e1000e/netdev.c +++ b/drivers/net/e1000e/netdev.c @@ -2751,23 +2751,25 @@ void e1000e_reset(struct e1000_adapter *adapter) /* * flow control settings * - * The high water mark must be low enough to fit one full frame + * The high water mark must be low enough to fit two full frame * (or the size used for early receive) above it in the Rx FIFO. * Set it to the lower of: * - 90% of the Rx FIFO size, and * - the full Rx FIFO size minus the early receive size (for parts * with ERT support assuming ERT set to E1000_ERT_2048), or - * - the full Rx FIFO size minus one full frame + * - the full Rx FIFO size minus two full frames */ - if (adapter->flags & FLAG_HAS_ERT) + if ((adapter->flags & FLAG_HAS_ERT) && + (adapter->netdev->mtu > ETH_DATA_LEN)) hwm = min(((pba << 10) * 9 / 10), ((pba << 10) - (E1000_ERT_2048 << 3))); else hwm = min(((pba << 10) * 9 / 10), - ((pba << 10) - adapter->max_frame_size)); + ((pba << 10) - (2 * adapter->max_frame_size))); - fc->high_water = hwm & 0xFFF8; /* 8-byte granularity */ - fc->low_water = fc->high_water - 8; + fc->high_water = hwm & E1000_FCRTH_RTH; /* 8-byte granularity */ + fc->low_water = (fc->high_water - (2 * adapter->max_frame_size)); + fc->low_water &= E1000_FCRTL_RTL; /* 8-byte granularity */ if (adapter->flags & FLAG_DISABLE_FC_PAUSE_TIME) fc->pause_time = 0xFFFF; -- 2.30.2