From 3d680c57286a2f77b9cfba275756c711730c7fe2 Mon Sep 17 00:00:00 2001 From: Jasper Scholte Date: Sun, 14 Aug 2016 23:30:44 +0200 Subject: [PATCH] ramips: add support for Sitecom WLR-6000 The Sitecom firmware upgrade file has SENAO_FIRMWARE_TYPE 2 set. This looks rather wrong since SENAO_FIRMWARE_TYPE 2 is kernel only but the file is way to big for only including a kernel. The factory image need to have the dlf file extension. Otherwise the Sitecom firmware rejects the file. The stock firmware uses the following mac addresses: LAN: 00:0C:F6:AA:BB:D8 (u-boot env: ethaddr) 2,4: 00:0C:F6:AA:BB:D8 (EEPROM) 5: 00:0C:F6:AA:BB:DC (EEPROM) WAN: 00:0C:F6:AA:C8:43 (u-boot env: wanaddr) Assuming the mac address range :D8 to :DC is reserved for this device, the MAC addresses were reorder to have a unique MAC address for each interface: 2.4GHz: 00:0C:F6:AA:BB:D8 LAN: 00:0C:F6:AA:BB:D9 WAN: 00:0C:F6:AA:BB:DA 5 GHz: 00:0C:F6:AA:BB:DC The first MAC is assigned to the 2.4GHz WiFi interface to keep compatibility with the SSIDs printed on the case, which have the last three sextets of the MAC address appended. There are still issues with the rt2x00 driver. It is not possible to use both wireless interfaces at the same time. The 2.4 GHz wireless (PCIe) only works if the internal 5GHz wireless is/has been enabled or used for scanning. The internal 5GHz wireless only works if the 2.4GHz wireless (PCIe) was never enabled. Disabling the 2.4Ghz after it was enabled will result in stations seeing the 5Ghz AP but are unable to connect. Due to the not optimal working wifi the manufacture, backup and storage partitions of the OEM firmware are kept for now to allow an easy switch back to the Sitecom firmware. Signed-off-by: Jasper Scholte Signed-off-by: Mathias Kresin --- .../ramips/base-files/etc/board.d/02_network | 6 +- target/linux/ramips/base-files/etc/diag.sh | 3 + target/linux/ramips/base-files/lib/ramips.sh | 3 + .../ramips/base-files/lib/upgrade/platform.sh | 1 + target/linux/ramips/dts/WLR-6000.dts | 186 ++++++++++++++++++ target/linux/ramips/image/rt3883.mk | 13 ++ 6 files changed, 211 insertions(+), 1 deletion(-) create mode 100644 target/linux/ramips/dts/WLR-6000.dts diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network index 537448ec9d..1e97c3b3c2 100755 --- a/target/linux/ramips/base-files/etc/board.d/02_network +++ b/target/linux/ramips/base-files/etc/board.d/02_network @@ -226,7 +226,8 @@ ramips_setup_interfaces() "0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "8@eth0" ;; tew-691gr|\ - tew-692gr) + tew-692gr|\ + wlr-6000) ucidef_add_switch "switch0" \ "1:lan" "2:lan" "3:lan" "4:lan" "5:wan" "0@eth0" ;; @@ -383,6 +384,9 @@ ramips_setup_macs() lan_mac=$(mtd_get_mac_binary factory 4) wan_mac=$(mtd_get_mac_binary factory 40) ;; + wlr-6000) + wan_mac=$(macaddr_add "$(mtd_get_mac_binary factory 32772)" 2) + ;; wsr-1166) local index="$(find_mtd_index "board_data")" wan_mac="$(grep -m1 mac= "/dev/mtd${index}" | cut -d= -f2)" diff --git a/target/linux/ramips/base-files/etc/diag.sh b/target/linux/ramips/base-files/etc/diag.sh index f3910c7cba..52baa0b23e 100644 --- a/target/linux/ramips/base-files/etc/diag.sh +++ b/target/linux/ramips/base-files/etc/diag.sh @@ -207,6 +207,9 @@ get_status_led() { status_led="$board:amber:power" ;; whr-g300n|\ + wlr-6000) + status_led="$board:red:power" + ;; wzr-agl300nh) status_led="$board:green:router" ;; diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh index ee9073238d..c62f5f6a93 100755 --- a/target/linux/ramips/base-files/lib/ramips.sh +++ b/target/linux/ramips/base-files/lib/ramips.sh @@ -508,6 +508,9 @@ ramips_board_detect() { *"WLI-TX4-AG300N") name="wli-tx4-ag300n" ;; + *"WLR-6000") + name="wlr-6000" + ;; *"WMR-300") name="wmr-300" ;; diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh index d5d0463a60..fa108b6ce4 100755 --- a/target/linux/ramips/base-files/lib/upgrade/platform.sh +++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh @@ -148,6 +148,7 @@ platform_check_image() { wl-351|\ wl-wn575a3|\ wli-tx4-ag300n|\ + wlr-6000|\ wmr-300|\ wnce2001|\ wndr3700v5|\ diff --git a/target/linux/ramips/dts/WLR-6000.dts b/target/linux/ramips/dts/WLR-6000.dts new file mode 100644 index 0000000000..ff3096907e --- /dev/null +++ b/target/linux/ramips/dts/WLR-6000.dts @@ -0,0 +1,186 @@ +/dts-v1/; + +#include "rt3883.dtsi" + +#include +#include + +/ { + model = "Sitecom WLR-6000"; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <20>; + + reset { + label = "reset"; + gpios = <&gpio1 2 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + power { + label = "wlr-6000:red:power"; + gpios = <&gpio0 1 GPIO_ACTIVE_LOW>; + }; + + ops { + label = "wlr-6000:white:ops"; + gpios = <&gpio0 0 GPIO_ACTIVE_LOW>; + }; + }; + + gpio_export { + compatible = "gpio-export"; + #size-cells = <0>; + + usb { + gpio-export,name = "usb"; + gpio-export,output = <1>; + gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&gpio1 { + status = "okay"; +}; + +&pinctrl { + state_default: pinctrl0 { + gpio { + ralink,group = "i2c", "jtag", "uartf"; + ralink,function = "gpio"; + }; + }; +}; + +ðernet { + status = "okay"; + mtd-mac-address = <&factory 0x8004>; + mtd-mac-address-increment = <1>; + + port@0 { + phy-handle = <&phy0>; + phy-mode = "rgmii"; + }; + + mdio-bus { + status = "okay"; + + phy0: ethernet-phy@0 { + reg = <0>; + phy-mode = "rgmii"; + + qca,ar8327-initvals = < + 0x04 0x07600000 /* PORT0 PAD MODE CTRL */ + 0x0c 0x07600000 /* PORT6 PAD MODE CTRL */ + 0x10 0x40000000 /* Power-on Strapping: 176-pin interface configuration */ + 0x50 0xc437c437 /* LED Control Register 0 */ + 0x54 0xc337c337 /* LED Control Register 1 */ + 0x58 0x00000000 /* LED Control Register 2 */ + 0x5c 0x03ffff00 /* LED Control Register 3 */ + 0x7c 0x0000007e /* PORT0_STATUS */ + 0x94 0x0000007e /* PORT6 STATUS */ + >; + }; + }; +}; + +&spi0 { + status = "okay"; + + m25p80@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <8600000>; + m25p,fast-read; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x30000>; + read-only; + }; + + partition@30000 { + label = "u-boot-env"; + reg = <0x30000 0x10000>; + read-only; + }; + + factory: partition@40000 { + label = "factory"; + reg = <0x40000 0x10000>; + read-only; + }; + + partition@50000 { + label = "firmware"; + reg = <0x50000 0x713000>; + }; + + partition@763000 { + label = "manufacture"; + reg = <0x763000 0x7D000>; + read-only; + }; + + partition@7E0000 { + label = "backup"; + reg = <0x7E0000 0x10000>; + read-only; + }; + + partition@7F0000 { + label = "storage"; + reg = <0x7F0000 0x10000>; + read-only; + }; + }; +}; + +&pci { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pci_pins>; + + pci_pins: pci { + pci { + ralink,group = "pci"; + ralink,function = "pci-fnc"; + }; + }; + + host-bridge { + pci-bridge@1 { + status = "okay"; + + wifi@1814,3091 { + compatible = "pci1814,3091"; + reg = <0x10000 0 0 0 0>; + ralink,mtd-eeprom = <&factory 0x8000>; + }; + }; + }; +}; + +&wmac { + status = "okay"; + ralink,2ghz = <0>; + ralink,mtd-eeprom = <&factory 0x0>; +}; + +&ehci { + status = "okay"; +}; + +&ohci { + status = "okay"; +}; diff --git a/target/linux/ramips/image/rt3883.mk b/target/linux/ramips/image/rt3883.mk index efdbc1f6a8..89b215d6af 100644 --- a/target/linux/ramips/image/rt3883.mk +++ b/target/linux/ramips/image/rt3883.mk @@ -87,6 +87,19 @@ endef TARGET_DEVICES += tew-692gr +define Device/wlr-6000 + DTS := WLR-6000 + BLOCKSIZE := 4k + IMAGE_SIZE := 7244k + IMAGES += factory.dlf + IMAGE/factory.dlf := \ + $$(IMAGE/sysupgrade.bin) | senao-header -r 0x0202 -p 0x41 -t 2 + DEVICE_TITLE := Sitecom WLR-6000 + DEVICE_PACKAGES := kmod-usb-core kmod-usb-ohci kmod-usb2 swconfig +endef +TARGET_DEVICES += wlr-6000 + + define BuildFirmware/RTN56U/squashfs $(call BuildFirmware/Default8M/$(1),$(1),rt-n56u,RT-N56U) -mkrtn56uimg -s $(call sysupname,$(1),rt-n56u) -- 2.30.2