From 3aef61060e3f51aa43fe494d5ff173e81dd43003 Mon Sep 17 00:00:00 2001 From: Glen Lee Date: Thu, 29 Jun 2023 15:58:05 -0400 Subject: [PATCH] ipq806x: add support for Extreme Networks AP3935 Extreme Networks AP3935i/e - https://www.extremenetworks.com/support/documentation/access-points-ap3935i-e/ SoC: IPQ8068 QYY AT46279K45060I RAM: NANYA 1527 NT5CC256M16DP-DI 515073W0EF 7 TW FLASH: NOR - S25FL256S1 - 32MB NAND - Macronix MX30UF4G28AB - 512MB LAN: Atheros AR8035-A J5150WL 1515 CN - RGMII LAN2: Atheros AR8033-AL1A SKCSR.AJ1 1444 China - SGMII WLAN2: QCA9990 OVV FNPV209 K451406 WLAN5: QCA9990 OVV FNPV209 K451406 SERIAL: RS232 Port (115200 8n1) Cisco console cable and 4pin Serial Header | 3.3 | GND | RX | TX MAC address for LAN1/LAN2/WLAN 2G/WLAN 5G in uboot env * Installation via either RJ45 console or on-board 4 PIN header Install Method -------------- 1) Setup TFTP server, and place openwrt-ipq806x-generic-extreme_ap3935-initramfs-uImage image in /srv/tftp or similar 2) Connect to console on router and connect ethernet port "LAN1" to your LAN 3) Interupt the boot with any character 4) Login with admin/new2day for default password (use reset/FactoryDefault if password needs to be reset) 5) Set serverip to TFTP IP: set serverip 192.168.1.2 6) Set ipaddr to another IP: set ipaddr 192.168.1.101 7) Make uboot ping something to activate eth0 on boot: set bootcmd 'ping 192.168.1.1; run boot_flash' saveenv 8) TFTP image to RAM: tftpboot 0x42000000 openwrt-ipq806x-generic-extreme_ap3935i-initramfs-uImage 9) Boot image: bootm 0x42000000 In OpenWRT, "LAN1" is LAN, "LAN2" is WAN 10) SFTP openwrt-ipq806x-generic-extreme_ap3935-squashfs-nand-sysupgrade.bin image to /tmp 11) sysupgrade /tmp/openwrt-*-nand-sysupgrade.bin Signed-off-by: Glen Lee --- package/boot/uboot-envtools/files/ipq806x | 4 + .../ipq806x/base-files/etc/board.d/01_leds | 4 + .../ipq806x/base-files/etc/board.d/02_network | 3 +- .../etc/hotplug.d/ieee80211/10_fix_wifi_mac | 5 + .../ipq806x/base-files/etc/init.d/bootcount | 3 + .../base-files/lib/upgrade/platform.sh | 5 + target/linux/ipq806x/config-6.1 | 1 + .../arch/arm/boot/dts/qcom-ipq8068-ap3935.dts | 351 ++++++++++++++++++ target/linux/ipq806x/image/generic.mk | 17 + 9 files changed, 392 insertions(+), 1 deletion(-) create mode 100644 target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8068-ap3935.dts diff --git a/package/boot/uboot-envtools/files/ipq806x b/package/boot/uboot-envtools/files/ipq806x index 01a86c7b19..443a0e13d4 100644 --- a/package/boot/uboot-envtools/files/ipq806x +++ b/package/boot/uboot-envtools/files/ipq806x @@ -38,6 +38,10 @@ askey,rt4230w-rev6) edgecore,ecw5410) ubootenv_add_uci_config "/dev/mtd11" "0x0" "0x10000" "0x10000" ;; +extreme,ap3935) + ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x10000" "0x10000" + ubootenv_add_uci_config "/dev/mtd3" "0x0" "0x10000" "0x10000" + ;; linksys,ea7500-v1|\ linksys,ea8500) ubootenv_add_uci_config "/dev/mtd10" "0x0" "0x20000" "0x20000" diff --git a/target/linux/ipq806x/base-files/etc/board.d/01_leds b/target/linux/ipq806x/base-files/etc/board.d/01_leds index 0b64bbb420..511adc5a50 100644 --- a/target/linux/ipq806x/base-files/etc/board.d/01_leds +++ b/target/linux/ipq806x/base-files/etc/board.d/01_leds @@ -33,6 +33,10 @@ edgecore,ecw5410) ucidef_set_led_wlan "wlan2g" "WLAN2G" "green:wlan2g" "phy1tpt" ucidef_set_led_wlan "wlan5g" "WLAN5G" "green:wlan5g" "phy0tpt" ;; +extreme,ap3935) + ucidef_set_led_netdev "wan" "wan" "orange:lan1" "eth1" + ucidef_set_led_netdev "lan" "lan" "orange:lan2" "eth0" + ;; meraki,mr52) ucidef_set_led_netdev "eth0" "eth0" "green:lan1" "eth0" ucidef_set_led_netdev "eth1" "eth1" "green:lan2" "eth1" diff --git a/target/linux/ipq806x/base-files/etc/board.d/02_network b/target/linux/ipq806x/base-files/etc/board.d/02_network index 3ba3ff79e9..a4316272e9 100644 --- a/target/linux/ipq806x/base-files/etc/board.d/02_network +++ b/target/linux/ipq806x/base-files/etc/board.d/02_network @@ -39,7 +39,8 @@ ipq806x_setup_interfaces() tplink,onhub) ucidef_set_interfaces_lan_wan "lan1" "wan" ;; - edgecore,ecw5410) + edgecore,ecw5410 |\ + extreme,ap3935) ucidef_set_interfaces_lan_wan "eth1" "eth0" ;; qcom,ipq8064-ap161) diff --git a/target/linux/ipq806x/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac b/target/linux/ipq806x/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac index 5af3a5b805..ef5fc344a6 100644 --- a/target/linux/ipq806x/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac +++ b/target/linux/ipq806x/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac @@ -15,6 +15,11 @@ case "$board" in ubnt,unifi-ac-hd) macaddr_add $(mtd_get_mac_binary EEPROM 0x6) $(($PHYNBR + 1)) > /sys${DEVPATH}/macaddress ;; + extreme,ap3935) + echo "##### PHYNBR=$PHYNBR DEVPATH=$DEVPATH" + [ "$PHYNBR" = "0" ] && echo $(mtd_get_mac_ascii CFG1 RADIOADDR0) > /sys${DEVPATH}/macaddress + [ "$PHYNBR" = "1" ] && echo $(mtd_get_mac_ascii CFG1 RADIOADDR1) > /sys${DEVPATH}/macaddress + ;; esac OPATH=${DEVPATH##/devices/platform/} diff --git a/target/linux/ipq806x/base-files/etc/init.d/bootcount b/target/linux/ipq806x/base-files/etc/init.d/bootcount index cb32a4ed35..ef3c6894e4 100755 --- a/target/linux/ipq806x/base-files/etc/init.d/bootcount +++ b/target/linux/ipq806x/base-files/etc/init.d/bootcount @@ -12,6 +12,9 @@ boot() { edgecore,ecw5410) fw_setenv bootcount 0 ;; + extreme,ap3935) + fw_setenv WATCHDOG_COUNT 0x00000000 + ;; linksys,ea7500-v1 |\ linksys,ea8500) mtd resetbc s_env || true diff --git a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh index 8eda75b718..7877ecae6b 100644 --- a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh @@ -44,6 +44,11 @@ platform_do_upgrade() { fi nand_do_upgrade "$1" ;; + extreme,ap3935) + CI_ROOTPART="nand_flash" + CI_KERNPART="PriImg" + nand_do_upgrade "$1" + ;; linksys,ea7500-v1 |\ linksys,ea8500) platform_do_upgrade_linksys "$1" diff --git a/target/linux/ipq806x/config-6.1 b/target/linux/ipq806x/config-6.1 index c008613713..e31e822380 100644 --- a/target/linux/ipq806x/config-6.1 +++ b/target/linux/ipq806x/config-6.1 @@ -318,6 +318,7 @@ CONFIG_NVMEM_QCOM_QFPROM=y # CONFIG_NVMEM_QCOM_SEC_QFPROM is not set # CONFIG_NVMEM_SPMI_SDAM is not set CONFIG_NVMEM_SYSFS=y +CONFIG_NVMEM_U_BOOT_ENV=y CONFIG_OF=y CONFIG_OF_ADDRESS=y CONFIG_OF_EARLY_FLATTREE=y diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8068-ap3935.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8068-ap3935.dts new file mode 100644 index 0000000000..5c75de8f8d --- /dev/null +++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8068-ap3935.dts @@ -0,0 +1,351 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qcom-ipq8064-v2.0.dtsi" + +#include +#include + +/ { + model = "Extreme Networks AP3935"; + compatible = "extreme,ap3935", "qcom,ipq8064"; + + memory@0 { + reg = <0x41400000 0x3ec00000>; + device_type = "memory"; + }; + + aliases { + serial0 = &gsbi7_serial; + serial1 = &gsbi2_serial; + mdio-gpio0 = &mdio0; + ethernet0 = &gmac0; + ethernet1 = &gmac2; + + led-boot = &led_power_green; + led-failsafe = &led_power_orange; + led-running = &led_power_green; + led-upgrade = &led_power_green; + }; + + chosen { + stdout-path = "serial0:115200n8"; + bootargs-override = "ubi.block=0,0 root=/dev/ubiblock0_0"; + }; + + keys { + compatible = "gpio-keys"; + pinctrl-0 = <&button_pins>; + pinctrl-names = "default"; + + reset { + label = "reset"; + gpios = <&qcom_pinmux 56 GPIO_ACTIVE_LOW>; + linux,code = ; + debounce-interval = <60>; + wakeup-source; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-0 = <&led_pins>; + pinctrl-names = "default"; + + led_power_green: power_green { + label = "green:power"; + gpios = <&qcom_pinmux 22 GPIO_ACTIVE_LOW>; + }; + + led_power_orange: power_orange { + label = "orange:power"; + gpios = <&qcom_pinmux 23 GPIO_ACTIVE_LOW>; + }; + + led_wlan2g_green { + label = "green:wlan2g"; + gpios = <&qcom_pinmux 24 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + + led_wlan5g_green { + label = "green:wlan5g"; + gpios = <&qcom_pinmux 25 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy1tpt"; + }; + + led_lan1_green { + label = "green:lan1"; + gpios = <&qcom_pinmux 26 GPIO_ACTIVE_LOW>; + }; + + led_lan1_orange { + label = "orange:lan1"; + gpios = <&qcom_pinmux 27 GPIO_ACTIVE_LOW>; + }; + + led_lan2_green { + label = "green:lan2"; + gpios = <&qcom_pinmux 28 GPIO_ACTIVE_LOW>; + }; + + led_lan2_orange { + label = "orange:lan2"; + gpios = <&qcom_pinmux 29 GPIO_ACTIVE_LOW>; + }; + }; +}; + + +&qcom_pinmux { + spi_pins: spi_pins { + mux { + pins = "gpio18", "gpio19"; + function = "gsbi5"; + drive-strength = <10>; + bias-pull-down; + }; + + clk { + pins = "gpio21"; + function = "gsbi5"; + drive-strength = <12>; + bias-pull-down; + }; + + cs { + pins = "gpio20"; + function = "gpio"; + drive-strength = <10>; + bias-pull-up; + }; + }; + + led_pins: led_pins { + mux { + pins = "gpio22", "gpio23", "gpio24", "gpio25", + "gpio26", "gpio27", "gpio28", "gpio29"; + function = "gpio"; + drive-strength = <10>; + bias-pull-up; + }; + }; + + button_pins: button_pins { + mux { + pins = "gpio56"; + function = "gpio"; + bias-pull-up; + }; + }; +}; + +&gsbi2 { + qcom,mode = ; + status = "okay"; + + gsbi2_serial: serial@12490000 { + status = "okay"; + }; +}; + +&gsbi4 { + qcom,mode = ; + status = "okay"; + + serial@16340000 { + status = "disabled"; + }; +}; + +&gsbi7 { + qcom,mode = ; + status = "okay"; + + gsbi7_serial: serial@16640000 { + status = "okay"; + }; +}; + +&gsbi5 { + qcom,mode = ; + status = "okay"; + + spi4: spi@1a280000 { + status = "okay"; + spi-max-frequency = <50000000>; + + pinctrl-0 = <&spi_pins>; + pinctrl-names = "default"; + + cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>; + + flash@0 { + compatible = "jedec,spi-nor"; + #address-cells = <1>; + #size-cells = <1>; + spi-max-frequency = <50000000>; + reg = <0>; + + partitions { + compatible = "fixed-partitions"; + + cfg1@02a0000 { + compatible = "u-boot,env-redundant-bool"; + label = "CFG1"; + reg = <0x02a0000 0x0010000>; + + ethaddr: ethaddr { + }; + }; + + bootpri@02b0000 { + label = "BootPRI"; + reg = <0x02b0000 0x0080000>; + }; + + cfg2@0330000 { + label = "CFG2"; + reg = <0x0330000 0x0010000>; + }; + + fs@0340000 { + label = "FS"; + reg = <0x0340000 0x0080000>; + }; + + priimg@03c0000 { + label = "PriImg"; + reg = <0x03c0000 0x0e10000>; + }; + + secimg@11d0000 { + label = "SecImg"; + reg = <0x11d0000 0x0e10000>; + }; + }; + }; + }; +}; + +&pcie0 { + status = "okay"; + + /delete-property/ pinctrl-0; + /delete-property/ pinctrl-names; + + bridge@0,0 { + reg = <0x00000000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + ranges; + + wifi@1,0 { + compatible = "qcom,ath10k"; + status = "okay"; + reg = <0x00010000 0 0 0 0>; + }; + }; +}; + +&pcie1 { + status = "okay"; + + /delete-property/ pinctrl-0; + /delete-property/ pinctrl-names; + + bridge@0,0 { + reg = <0x00000000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + ranges; + + wifi@1,0 { + compatible = "qcom,ath10k"; + status = "okay"; + reg = <0x00010000 0 0 0 0>; + }; + }; +}; + +&nand { + status = "okay"; + + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + + nand@0 { + compatible = "qcom,nandcs"; + + reg = <0>; + + nand-ecc-strength = <8>; + nand-bus-width = <8>; + nand-ecc-step-size = <512>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + ubi@0 { + label = "ubi"; + reg = <0x0000000 0x20000000>; + }; + }; + }; +}; + +&soc { + mdio1: mdio { + compatible = "virtual,mdio-gpio"; + #address-cells = <1>; + #size-cells = <0>; + + status = "okay"; + + pinctrl-0 = <&mdio0_pins>; + pinctrl-names = "default"; + + gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>; + + phy1: ethernet-phy@1 { + reg = <1>; + }; + + phy2: ethernet-phy@2 { + reg = <2>; + }; + }; +}; + +&gmac0 { + status = "okay"; + + qcom,id = <0>; + mdiobus = <&mdio1>; + + phy-mode = "rgmii"; + phy-handle = <&phy1>; + + nvmem-cells = <ðaddr>; + nvmem-cell-names = "mac-address"; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&gmac2 { + status = "okay"; + + qcom,id = <2>; + mdiobus = <&mdio1>; + + phy-mode = "sgmii"; + phy-handle = <&phy2>; +}; + +&adm_dma { + status = "okay"; +}; diff --git a/target/linux/ipq806x/image/generic.mk b/target/linux/ipq806x/image/generic.mk index 0339a612d8..b3743c35e3 100644 --- a/target/linux/ipq806x/image/generic.mk +++ b/target/linux/ipq806x/image/generic.mk @@ -160,6 +160,23 @@ define Device/edgecore_ecw5410 endef TARGET_DEVICES += edgecore_ecw5410 +define Device/extreme_ap3935 + $(call Device/LegacyImage) + $(call Device/UbiFit) + DEVICE_VENDOR := Extreme Networks + DEVICE_MODEL := AP3935 + SOC := qcom-ipq8068 + PAGESIZE := 2048 + BLOCKSIZE := 128k + KERNEL = kernel-bin | append-dtb | uImage none | append-uImage-fakehdr filesystem + KERNEL_LOADADDR = 0x41408000 + KERNEL_SIZE := 14400k + KERNEL_SUFFIX := -uImage + UBINIZE_OPTS := -E 5 + DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct +endef +TARGET_DEVICES += extreme_ap3935 + define Device/linksys_ea7500-v1 $(call Device/LegacyImage) $(Device/kernel-size-migration) -- 2.30.2