From 3810e897295cb66bc45a62bc2c0b70a01004fe3b Mon Sep 17 00:00:00 2001 From: Paul Fertser Date: Fri, 1 Oct 2021 12:37:11 +0300 Subject: [PATCH] realtek: ensure output drivers are enabled in RTL8231 The bootloader can leave the GPIO expander in a state which doesn't have output drivers enabled so GPIOs will properly work for input but output operations will have no effect. To avoid disrupting the boot in case the bootloader left direction and data registers in an inconsistent state (e.g. pulling SoC's reset to 0) reconfigure everything as input. Reviewed-by: Sander Vanheule Signed-off-by: Paul Fertser --- .../realtek/files-5.10/drivers/gpio/gpio-rtl8231.c | 12 +++++++----- .../realtek/files-5.4/drivers/gpio/gpio-rtl8231.c | 12 +++++++----- 2 files changed, 14 insertions(+), 10 deletions(-) diff --git a/target/linux/realtek/files-5.10/drivers/gpio/gpio-rtl8231.c b/target/linux/realtek/files-5.10/drivers/gpio/gpio-rtl8231.c index a8ffcdc313..f4f5621e0c 100644 --- a/target/linux/realtek/files-5.10/drivers/gpio/gpio-rtl8231.c +++ b/target/linux/realtek/files-5.10/drivers/gpio/gpio-rtl8231.c @@ -239,8 +239,6 @@ void rtl8231_gpio_set(struct gpio_chip *gc, unsigned int offset, int value) int rtl8231_init(struct rtl8231_gpios *gpios) { - u32 v; - pr_info("%s called, MDIO bus ID: %d\n", __func__, gpios->smi_bus_id); gpios->reg_cached = 0; @@ -254,11 +252,15 @@ int rtl8231_init(struct rtl8231_gpios *gpios) sw_w32_mask(3, 1, RTL838X_DMY_REG5); } - /* Select GPIO functionality for pins 0-34 */ + /* Select GPIO functionality and force input direction for pins 0-36 */ rtl8231_write(gpios, RTL8231_GPIO_PIN_SEL(0), 0xffff); + rtl8231_write(gpios, RTL8231_GPIO_DIR(0), 0xffff); rtl8231_write(gpios, RTL8231_GPIO_PIN_SEL(16), 0xffff); - v = rtl8231_read(gpios, RTL8231_GPIO_PIN_SEL(32)); - rtl8231_write(gpios, RTL8231_GPIO_PIN_SEL(32), v | 0x7); + rtl8231_write(gpios, RTL8231_GPIO_DIR(16), 0xffff); + rtl8231_write(gpios, RTL8231_GPIO_PIN_SEL(32), 0x03ff); + + /* Set LED_Start to enable drivers for output mode */ + rtl8231_write(gpios, RTL8231_LED_FUNC0, 1 << 1); return 0; } diff --git a/target/linux/realtek/files-5.4/drivers/gpio/gpio-rtl8231.c b/target/linux/realtek/files-5.4/drivers/gpio/gpio-rtl8231.c index a8ffcdc313..f4f5621e0c 100644 --- a/target/linux/realtek/files-5.4/drivers/gpio/gpio-rtl8231.c +++ b/target/linux/realtek/files-5.4/drivers/gpio/gpio-rtl8231.c @@ -239,8 +239,6 @@ void rtl8231_gpio_set(struct gpio_chip *gc, unsigned int offset, int value) int rtl8231_init(struct rtl8231_gpios *gpios) { - u32 v; - pr_info("%s called, MDIO bus ID: %d\n", __func__, gpios->smi_bus_id); gpios->reg_cached = 0; @@ -254,11 +252,15 @@ int rtl8231_init(struct rtl8231_gpios *gpios) sw_w32_mask(3, 1, RTL838X_DMY_REG5); } - /* Select GPIO functionality for pins 0-34 */ + /* Select GPIO functionality and force input direction for pins 0-36 */ rtl8231_write(gpios, RTL8231_GPIO_PIN_SEL(0), 0xffff); + rtl8231_write(gpios, RTL8231_GPIO_DIR(0), 0xffff); rtl8231_write(gpios, RTL8231_GPIO_PIN_SEL(16), 0xffff); - v = rtl8231_read(gpios, RTL8231_GPIO_PIN_SEL(32)); - rtl8231_write(gpios, RTL8231_GPIO_PIN_SEL(32), v | 0x7); + rtl8231_write(gpios, RTL8231_GPIO_DIR(16), 0xffff); + rtl8231_write(gpios, RTL8231_GPIO_PIN_SEL(32), 0x03ff); + + /* Set LED_Start to enable drivers for output mode */ + rtl8231_write(gpios, RTL8231_LED_FUNC0, 1 << 1); return 0; } -- 2.30.2