From 2dae800f1e6193b64ba587f511c4878c89409cbe Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Sun, 21 Dec 2014 16:28:32 +0100 Subject: [PATCH] sunxi: video: Add lcd output support Add lcd output support, see the new Kconfig entries and doc/README.video for how to enable / configure this. Signed-off-by: Hans de Goede Acked-by: Ian Campbell --- arch/arm/include/asm/arch-sunxi/display.h | 30 +++- arch/arm/include/asm/arch-sunxi/gpio.h | 2 + board/sunxi/Kconfig | 43 +++++- doc/README.video | 50 +++++- drivers/video/sunxi_display.c | 180 ++++++++++++++++++++-- 5 files changed, 278 insertions(+), 27 deletions(-) diff --git a/arch/arm/include/asm/arch-sunxi/display.h b/arch/arm/include/asm/arch-sunxi/display.h index 00e34665da..1d4e935017 100644 --- a/arch/arm/include/asm/arch-sunxi/display.h +++ b/arch/arm/include/asm/arch-sunxi/display.h @@ -57,14 +57,16 @@ struct sunxi_lcdc_reg { u32 int0; /* 0x04 */ u32 int1; /* 0x08 */ u8 res0[0x04]; /* 0x0c */ - u32 frame_ctrl; /* 0x10 */ - u8 res1[0x2c]; /* 0x14 */ + u32 tcon0_frm_ctrl; /* 0x10 */ + u32 tcon0_frm_seed[6]; /* 0x14 */ + u32 tcon0_frm_table[4]; /* 0x2c */ + u8 res1[4]; /* 0x3c */ u32 tcon0_ctrl; /* 0x40 */ u32 tcon0_dclk; /* 0x44 */ - u32 tcon0_basic_timing0; /* 0x48 */ - u32 tcon0_basic_timing1; /* 0x4c */ - u32 tcon0_basic_timing2; /* 0x50 */ - u32 tcon0_basic_timing3; /* 0x54 */ + u32 tcon0_timing_active; /* 0x48 */ + u32 tcon0_timing_h; /* 0x4c */ + u32 tcon0_timing_v; /* 0x50 */ + u32 tcon0_timing_sync; /* 0x54 */ u32 tcon0_hv_intf; /* 0x58 */ u8 res2[0x04]; /* 0x5c */ u32 tcon0_cpu_intf; /* 0x60 */ @@ -175,11 +177,27 @@ struct sunxi_hdmi_reg { */ #define SUNXI_LCDC_X(x) (((x) - 1) << 16) #define SUNXI_LCDC_Y(y) (((y) - 1) << 0) +#define SUNXI_LCDC_TCON_VSYNC_MASK (1 << 24) +#define SUNXI_LCDC_TCON_HSYNC_MASK (1 << 25) #define SUNXI_LCDC_CTRL_IO_MAP_MASK (1 << 0) #define SUNXI_LCDC_CTRL_IO_MAP_TCON0 (0 << 0) #define SUNXI_LCDC_CTRL_IO_MAP_TCON1 (1 << 0) #define SUNXI_LCDC_CTRL_TCON_ENABLE (1 << 31) +#define SUNXI_LCDC_TCON0_FRM_CTRL_RGB666 ((1 << 31) | (0 << 4)) +#define SUNXI_LCDC_TCON0_FRM_CTRL_RGB565 ((1 << 31) | (5 << 4)) +#define SUNXI_LCDC_TCON0_FRM_SEED 0x11111111 +#define SUNXI_LCDC_TCON0_FRM_TAB0 0x01010000 +#define SUNXI_LCDC_TCON0_FRM_TAB1 0x15151111 +#define SUNXI_LCDC_TCON0_FRM_TAB2 0x57575555 +#define SUNXI_LCDC_TCON0_FRM_TAB3 0x7f7f7777 +#define SUNXI_LCDC_TCON0_CTRL_CLK_DELAY(n) (((n) & 0x1f) << 4) +#define SUNXI_LCDC_TCON0_CTRL_ENABLE (1 << 31) +#define SUNXI_LCDC_TCON0_DCLK_DIV(n) ((n) << 0) #define SUNXI_LCDC_TCON0_DCLK_ENABLE (0xf << 28) +#define SUNXI_LCDC_TCON0_TIMING_H_BP(n) (((n) - 1) << 0) +#define SUNXI_LCDC_TCON0_TIMING_H_TOTAL(n) (((n) - 1) << 16) +#define SUNXI_LCDC_TCON0_TIMING_V_BP(n) (((n) - 1) << 0) +#define SUNXI_LCDC_TCON0_TIMING_V_TOTAL(n) (((n) * 2) << 16) #define SUNXI_LCDC_TCON1_CTRL_CLK_DELAY(n) (((n) & 0x1f) << 4) #define SUNXI_LCDC_TCON1_CTRL_ENABLE (1 << 31) #define SUNXI_LCDC_TCON1_TIMING_H_BP(n) (((n) - 1) << 0) diff --git a/arch/arm/include/asm/arch-sunxi/gpio.h b/arch/arm/include/asm/arch-sunxi/gpio.h index 32941cb3b5..9438f5a262 100644 --- a/arch/arm/include/asm/arch-sunxi/gpio.h +++ b/arch/arm/include/asm/arch-sunxi/gpio.h @@ -150,6 +150,8 @@ enum sunxi_gpio_number { #define SUNXI_GPC6_SDC2 3 +#define SUNXI_GPD0_LCD0 2 + #define SUNXI_GPF0_SDC0 2 #define SUNXI_GPF2_SDC0 2 diff --git a/board/sunxi/Kconfig b/board/sunxi/Kconfig index 80dc3f96ba..b4d6107cd3 100644 --- a/board/sunxi/Kconfig +++ b/board/sunxi/Kconfig @@ -280,17 +280,52 @@ config USB2_VBUS_PIN See USB1_VBUS_PIN help text. config VIDEO - boolean "Enable graphical uboot console on HDMI" + boolean "Enable graphical uboot console on HDMI, LCD or VGA" default y ---help--- - Say Y here to add support for using a cfb console on the HDMI output - found on most sunxi devices. + Say Y here to add support for using a cfb console on the HDMI, LCD + or VGA output found on most sunxi devices. See doc/README.video for + info on how to select the video output and mode. + +config VIDEO_LCD_MODE + string "LCD panel timing details" + depends on VIDEO + default "" + ---help--- + LCD panel timing details string, leave empty if there is no LCD panel. + This is in drivers/video/videomodes.c: video_get_params() format, e.g. + x:800,y:480,depth:18,pclk_khz:33000,le:16,ri:209,up:22,lo:22,hs:30,vs:1,sync:0,vmode:0 + +config VIDEO_LCD_POWER + string "LCD panel power enable pin" + depends on VIDEO + default "" + ---help--- + Set the power enable pin for the LCD panel. This takes a string in the + format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. + +config VIDEO_LCD_BL_EN + string "LCD panel backlight enable pin" + depends on VIDEO + default "" + ---help--- + Set the backlight enable pin for the LCD panel. This takes a string in the + the format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of + port H. + +config VIDEO_LCD_BL_PWM + string "LCD panel backlight pwm pin" + depends on VIDEO + default "" + ---help--- + Set the backlight pwm pin for the LCD panel. This takes a string in the + format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. config USB_KEYBOARD boolean "Enable USB keyboard support" default y ---help--- Say Y here to add support for using a USB keyboard (typically used - in combination with a graphical console on HDMI). + in combination with a graphical console). endif diff --git a/doc/README.video b/doc/README.video index dadbfcd2fd..cfe6318e12 100644 --- a/doc/README.video +++ b/doc/README.video @@ -5,15 +5,8 @@ * SPDX-License-Identifier: GPL-2.0+ */ -U-Boot MPC8xx video controller driver -====================================== - -The driver has been tested with the following configurations: - -- MPC823FADS with AD7176 on a PAL TV (YCbYCr) - arsenio@tin.it - "video-mode" environment variable -=============================== +================================= The 'video-mode' environment variable can be used to enable and configure some video drivers. The format matches the video= command-line option used @@ -28,4 +21,45 @@ for Linux: The frequency (in Hz) to use. A comma-separated list of device-specific options + +U-Boot MPC8xx video controller driver +===================================== + +The driver has been tested with the following configurations: + +- MPC823FADS with AD7176 on a PAL TV (YCbYCr) - arsenio@tin.it + Example: video-mode=fslfb:1280x1024-32@60,monitor=dvi + + +U-boot sunxi video controller driver +==================================== + +U-boot supports hdmi and lcd output on Allwinner sunxi SoCs, lcd output +requires the CONFIG_VIDEO_LCD_MODE Kconfig value to be set. + +The sunxi u-boot driver supports the following video-mode options: + +- monitor=[none|dvi|hdmi|lcd] - Select the video output to use + none: Disable video output. + dvi/hdmi: Selects output over the hdmi connector with dvi resp. hdmi output + format, if edid is used the format is automatically selected. + lcd: Selects video output to a LCD screen. + vga: Selects bideo output over the VGA connector. + Defaults to monitor=dvi. + +- hpd=[0|1] - Enable use of the hdmi HotPlug Detect feature + 0: Disabled. Configure dvi/hdmi output even if no cable is detected + 1: Enabled. If a LCD has been configured fallback to the LCD when no cable is + detected, if no LCD is configured, disable video ouput. + Defaults to hpd=1. + +- edid=[0|1] - Enable use of DDC + EDID to get monitor info + 0: Disabled. + 1: Enabled. If valid EDID info was read from the monitor the EDID info will + overrides the xres, yres and refresh from the video-mode env. variable. + Defaults to edid=1. + +For example to always use the hdmi connector, even if no cable is inserted, +using edid info when available and otherwise initalizing it at 1024x768@60Hz, +use: video-mode=sunxi:1024x768-24@60,monitor=dvi,hpd=0,edid=1 . diff --git a/drivers/video/sunxi_display.c b/drivers/video/sunxi_display.c index ad38f162fd..46346eec0f 100644 --- a/drivers/video/sunxi_display.c +++ b/drivers/video/sunxi_display.c @@ -11,7 +11,9 @@ #include #include +#include #include +#include #include #include #include @@ -34,6 +36,7 @@ struct sunxi_display { GraphicDevice graphic_device; bool enabled; enum sunxi_monitor monitor; + unsigned int depth; } sunxi_display; /* @@ -435,6 +438,134 @@ static void sunxi_lcdc_enable(void) setbits_le32(&lcdc->ctrl, SUNXI_LCDC_CTRL_TCON_ENABLE); } +static void sunxi_lcdc_panel_enable(void) +{ + int pin; + + /* + * Start with backlight disabled to avoid the screen flashing to + * white while the lcd inits. + */ + pin = sunxi_name_to_gpio(CONFIG_VIDEO_LCD_BL_EN); + if (pin != -1) { + gpio_request(pin, "lcd_backlight_enable"); + gpio_direction_output(pin, 0); + } + + pin = sunxi_name_to_gpio(CONFIG_VIDEO_LCD_BL_PWM); + if (pin != -1) { + gpio_request(pin, "lcd_backlight_pwm"); + /* backlight pwm is inverted, set to 1 to disable backlight */ + gpio_direction_output(pin, 1); + } + + /* Give the backlight some time to turn off and power up the panel. */ + mdelay(40); + pin = sunxi_name_to_gpio(CONFIG_VIDEO_LCD_POWER); + if (pin != -1) { + gpio_request(pin, "lcd_power"); + gpio_direction_output(pin, 1); + } +} + +static void sunxi_lcdc_backlight_enable(void) +{ + int pin; + + /* + * We want to have scanned out at least one frame before enabling the + * backlight to avoid the screen flashing to white when we enable it. + */ + mdelay(40); + + pin = sunxi_name_to_gpio(CONFIG_VIDEO_LCD_BL_EN); + if (pin != -1) + gpio_direction_output(pin, 1); + + pin = sunxi_name_to_gpio(CONFIG_VIDEO_LCD_BL_PWM); + if (pin != -1) { + /* backlight pwm is inverted, set to 0 to enable backlight */ + gpio_direction_output(pin, 0); + } +} + +static int sunxi_lcdc_get_clk_delay(const struct ctfb_res_modes *mode) +{ + int delay; + + delay = mode->lower_margin + mode->vsync_len + mode->upper_margin - 2; + return (delay > 30) ? 30 : delay; +} + +static void sunxi_lcdc_tcon0_mode_set(const struct ctfb_res_modes *mode) +{ + struct sunxi_lcdc_reg * const lcdc = + (struct sunxi_lcdc_reg *)SUNXI_LCD0_BASE; + int bp, clk_delay, clk_div, clk_double, pin, total, val; + + for (pin = SUNXI_GPD(0); pin <= SUNXI_GPD(27); pin++) + sunxi_gpio_set_cfgpin(pin, SUNXI_GPD0_LCD0); + + sunxi_lcdc_pll_set(0, mode->pixclock_khz, &clk_div, &clk_double); + + /* Use tcon0 */ + clrsetbits_le32(&lcdc->ctrl, SUNXI_LCDC_CTRL_IO_MAP_MASK, + SUNXI_LCDC_CTRL_IO_MAP_TCON0); + + clk_delay = sunxi_lcdc_get_clk_delay(mode); + writel(SUNXI_LCDC_TCON0_CTRL_ENABLE | + SUNXI_LCDC_TCON0_CTRL_CLK_DELAY(clk_delay), &lcdc->tcon0_ctrl); + + writel(SUNXI_LCDC_TCON0_DCLK_ENABLE | + SUNXI_LCDC_TCON0_DCLK_DIV(clk_div), &lcdc->tcon0_dclk); + + writel(SUNXI_LCDC_X(mode->xres) | SUNXI_LCDC_Y(mode->yres), + &lcdc->tcon0_timing_active); + + bp = mode->hsync_len + mode->left_margin; + total = mode->xres + mode->right_margin + bp; + writel(SUNXI_LCDC_TCON0_TIMING_H_TOTAL(total) | + SUNXI_LCDC_TCON0_TIMING_H_BP(bp), &lcdc->tcon0_timing_h); + + bp = mode->vsync_len + mode->upper_margin; + total = mode->yres + mode->lower_margin + bp; + writel(SUNXI_LCDC_TCON0_TIMING_V_TOTAL(total) | + SUNXI_LCDC_TCON0_TIMING_V_BP(bp), &lcdc->tcon0_timing_v); + + writel(SUNXI_LCDC_X(mode->hsync_len) | SUNXI_LCDC_Y(mode->vsync_len), + &lcdc->tcon0_timing_sync); + + /* We only support hv-sync parallel lcd-s for now */ + writel(0, &lcdc->tcon0_hv_intf); + writel(0, &lcdc->tcon0_cpu_intf); + + if (sunxi_display.depth == 18 || sunxi_display.depth == 16) { + writel(SUNXI_LCDC_TCON0_FRM_SEED, &lcdc->tcon0_frm_seed[0]); + writel(SUNXI_LCDC_TCON0_FRM_SEED, &lcdc->tcon0_frm_seed[1]); + writel(SUNXI_LCDC_TCON0_FRM_SEED, &lcdc->tcon0_frm_seed[2]); + writel(SUNXI_LCDC_TCON0_FRM_SEED, &lcdc->tcon0_frm_seed[3]); + writel(SUNXI_LCDC_TCON0_FRM_SEED, &lcdc->tcon0_frm_seed[4]); + writel(SUNXI_LCDC_TCON0_FRM_SEED, &lcdc->tcon0_frm_seed[5]); + writel(SUNXI_LCDC_TCON0_FRM_TAB0, &lcdc->tcon0_frm_table[0]); + writel(SUNXI_LCDC_TCON0_FRM_TAB1, &lcdc->tcon0_frm_table[1]); + writel(SUNXI_LCDC_TCON0_FRM_TAB2, &lcdc->tcon0_frm_table[2]); + writel(SUNXI_LCDC_TCON0_FRM_TAB3, &lcdc->tcon0_frm_table[3]); + writel(((sunxi_display.depth == 18) ? + SUNXI_LCDC_TCON0_FRM_CTRL_RGB666 : + SUNXI_LCDC_TCON0_FRM_CTRL_RGB565), + &lcdc->tcon0_frm_ctrl); + } + + val = 0; + if (!(mode->sync & FB_SYNC_HOR_HIGH_ACT)) + val |= SUNXI_LCDC_TCON_HSYNC_MASK; + if (!(mode->sync & FB_SYNC_VERT_HIGH_ACT)) + val |= SUNXI_LCDC_TCON_VSYNC_MASK; + writel(val, &lcdc->tcon0_io_polarity); + + writel(0, &lcdc->tcon0_io_tristate); +} + static void sunxi_lcdc_tcon1_mode_set(const struct ctfb_res_modes *mode, int *clk_div, int *clk_double) { @@ -618,7 +749,12 @@ static void sunxi_mode_set(const struct ctfb_res_modes *mode, } break; case sunxi_monitor_lcd: - /* TODO */ + sunxi_lcdc_panel_enable(); + sunxi_composer_mode_set(mode, address); + sunxi_lcdc_tcon0_mode_set(mode); + sunxi_composer_enable(); + sunxi_lcdc_enable(); + sunxi_lcdc_backlight_enable(); break; case sunxi_monitor_vga: break; @@ -641,11 +777,11 @@ void *video_hw_init(void) { static GraphicDevice *graphic_device = &sunxi_display.graphic_device; const struct ctfb_res_modes *mode; - struct ctfb_res_modes edid_mode; + struct ctfb_res_modes custom; const char *options; - unsigned int depth; int i, ret, hpd, edid; char mon[16]; + char *lcd_mode = CONFIG_VIDEO_LCD_MODE; memset(&sunxi_display, 0, sizeof(struct sunxi_display)); @@ -653,7 +789,8 @@ void *video_hw_init(void) CONFIG_SUNXI_FB_SIZE >> 10); gd->fb_base = gd->ram_top; - video_get_ctfb_res_modes(RES_MODE_1024x768, 24, &mode, &depth, &options); + video_get_ctfb_res_modes(RES_MODE_1024x768, 24, &mode, + &sunxi_display.depth, &options); hpd = video_get_option_int(options, "hpd", 1); edid = video_get_option_int(options, "edid", 1); sunxi_display.monitor = sunxi_monitor_dvi; @@ -678,16 +815,26 @@ void *video_hw_init(void) ret = sunxi_hdmi_hpd_detect(); if (ret) { printf("HDMI connected: "); - if (edid && sunxi_hdmi_edid_get_mode(&edid_mode) == 0) - mode = &edid_mode; + if (edid && sunxi_hdmi_edid_get_mode(&custom) == 0) + mode = &custom; break; } if (!hpd) break; /* User has requested to ignore hpd */ sunxi_hdmi_shutdown(); - return NULL; + + if (lcd_mode[0] == 0) + return NULL; /* No LCD, bail */ + + /* Fall back / through to LCD */ + sunxi_display.monitor = sunxi_monitor_lcd; case sunxi_monitor_lcd: + if (lcd_mode[0]) { + sunxi_display.depth = video_get_params(&custom, lcd_mode); + mode = &custom; + break; + } printf("LCD not supported on this board\n"); return NULL; case sunxi_monitor_vga: @@ -729,16 +876,31 @@ int sunxi_simplefb_setup(void *blob) { static GraphicDevice *graphic_device = &sunxi_display.graphic_device; int offset, ret; + const char *pipeline = NULL; if (!sunxi_display.enabled) return 0; - /* Find a framebuffer node, with pipeline == "de_be0-lcd0-hdmi" */ + switch (sunxi_display.monitor) { + case sunxi_monitor_none: + return 0; + case sunxi_monitor_dvi: + case sunxi_monitor_hdmi: + pipeline = "de_be0-lcd0-hdmi"; + break; + case sunxi_monitor_lcd: + pipeline = "de_be0-lcd0"; + break; + case sunxi_monitor_vga: + break; + } + + /* Find a prefilled simpefb node, matching out pipeline config */ offset = fdt_node_offset_by_compatible(blob, -1, "allwinner,simple-framebuffer"); while (offset >= 0) { ret = fdt_find_string(blob, offset, "allwinner,pipeline", - "de_be0-lcd0-hdmi"); + pipeline); if (ret == 0) break; offset = fdt_node_offset_by_compatible(blob, offset, -- 2.30.2