From 27b2f0fc0fc5513304a5be3c5b8cb23aeb09e6f5 Mon Sep 17 00:00:00 2001 From: Ademar Arvati Filho Date: Fri, 6 Jul 2018 00:56:58 +0000 Subject: [PATCH] kirkwood: add support for Iomega Storcenter ix2-200 Iomega Storcenter ix2-200 is a dual SATA NAS powered by a Marvell Kirkwood SoC clocked at 1GHz. It has 256MB of RAM and 32MB of flash memory, 3x USB 2.0 and 1x 1Gbit/s NIC Specification: - SoC: Marvell Kirkwood 88F6281 - CPU/Speed: 1000Mhz - Flash-Chip: Hynix NAND - Flash size: 32 MiB,erase size:16 KiB,page size:512,OOB size:16 - RAM: 256MB - LAN: 1x 1000 Mbps Ethernet - WiFi: none - 3x USB 2.0 - UART: for serial console Installation instructions - easy steps: 1. download factory.bin and copy into tftp server 2. access uboot environment with serial cable and run ``` setenv mainlineLinux yes setenv arcNumber 1682 setenv console 'console=ttyS0,115200n8' setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)' setenv bootargs_root 'root=' setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000' saveenv setenv serverip 192.168.1.1 setenv ipaddr 192.168.1.13 tftpboot 0x00800000 factory.bin nand erase 0x100000 $(filesize) nand write 0x00800000 0x100000 $(filesize) run bootcmd ``` 3. access openwrt by dhcp ip address assigned by your router (p.ex: 192.168.1.13) Installation steps nand bad blocks proof: 1. download initramfs-uImage and copy into usb ext2 partition ``` mkfs.ext2 -L ext2 /dev/sdh1 mount -t ext2 /dev/sdh1 /mnt cp initramfs-uImage /mnt/initramfs.bin umount /mnt ``` 2. access uboot environment with serial cable and run ``` setenv mainlineLinux yes setenv arcNumber 1682 setenv console 'console=ttyS0,115200n8' setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)' setenv bootargs_root 'root=' setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000' saveenv usb reset; ext2load usb 0:1 0x00800000 /initramfs.bin; bootm 0x00800000 ``` 3. log into openwrt and sysupgrade to install into flash ``` sysupgrade -n /tmp/sysupgrade.bin ``` 4. access openwrt by dhcp ip address assigned by your router (p.ex: 192.168.1.13) Signed-off-by: Ademar Arvati Filho --- package/boot/uboot-envtools/files/kirkwood | 1 + .../kirkwood/base-files/etc/board.d/01_leds | 3 ++ .../base-files/etc/board.d/02_network | 1 + target/linux/kirkwood/base-files/etc/diag.sh | 3 ++ .../{nsa310_fancontrol => hwmon_fancontrol} | 13 +++++--- target/linux/kirkwood/image/Makefile | 16 +++++++++ .../patches-4.14/103-iomega-ix2-200.patch | 33 +++++++++++++++++++ .../patches-4.9/103-iomega-ix2-200.patch | 33 +++++++++++++++++++ 8 files changed, 98 insertions(+), 5 deletions(-) rename target/linux/kirkwood/base-files/etc/init.d/{nsa310_fancontrol => hwmon_fancontrol} (62%) create mode 100644 target/linux/kirkwood/patches-4.14/103-iomega-ix2-200.patch create mode 100644 target/linux/kirkwood/patches-4.9/103-iomega-ix2-200.patch diff --git a/package/boot/uboot-envtools/files/kirkwood b/package/boot/uboot-envtools/files/kirkwood index 16123846cc..b5f7ddccb7 100644 --- a/package/boot/uboot-envtools/files/kirkwood +++ b/package/boot/uboot-envtools/files/kirkwood @@ -15,6 +15,7 @@ board=$(board_name) case "$board" in cloudengines,pogoe02|\ cloudengines,pogoplugv4|\ +iom,ix2-200|\ linksys,viper|\ raidsonic,ib-nas62x0|\ seagate,dockstar|\ diff --git a/target/linux/kirkwood/base-files/etc/board.d/01_leds b/target/linux/kirkwood/base-files/etc/board.d/01_leds index 4e72e344aa..5cfc4cf309 100755 --- a/target/linux/kirkwood/base-files/etc/board.d/01_leds +++ b/target/linux/kirkwood/base-files/etc/board.d/01_leds @@ -14,6 +14,9 @@ case "$board" in ucidef_set_led_default "health" "health" "pogo_e02:green:health" "1" ucidef_set_led_default "fault" "fault" "pogo_e02:orange:fault" "1" ;; +"iom,ix2-200") + ucidef_set_led_timer "health" "health" "status:white:rebuild_led" "200" "800" + ;; "linksys,audi") ucidef_set_led_default "power" "power" "audi:green:power" "1" ;; diff --git a/target/linux/kirkwood/base-files/etc/board.d/02_network b/target/linux/kirkwood/base-files/etc/board.d/02_network index 5d66e0ffea..15e51d88f2 100755 --- a/target/linux/kirkwood/base-files/etc/board.d/02_network +++ b/target/linux/kirkwood/base-files/etc/board.d/02_network @@ -17,6 +17,7 @@ case "$board" in "cloudengines,pogoe02"|\ "cloudengines,pogoplugv4"|\ "iom,iconnect-1.1"|\ +"iom,ix2-200"|\ "raidsonic,ib-nas62x0"|\ "seagate,dockstar"|\ "seagate,goflexhome"|\ diff --git a/target/linux/kirkwood/base-files/etc/diag.sh b/target/linux/kirkwood/base-files/etc/diag.sh index 0667ad29fe..fc61846c11 100755 --- a/target/linux/kirkwood/base-files/etc/diag.sh +++ b/target/linux/kirkwood/base-files/etc/diag.sh @@ -15,6 +15,9 @@ get_status_led() { cloudengines,pogoplugv4) status_led="pogoplugv4:green:health" ;; + iom,ix2-200) + status_led="status:white:power_led" + ;; linksys,audi) status_led="audi:green:power" ;; diff --git a/target/linux/kirkwood/base-files/etc/init.d/nsa310_fancontrol b/target/linux/kirkwood/base-files/etc/init.d/hwmon_fancontrol similarity index 62% rename from target/linux/kirkwood/base-files/etc/init.d/nsa310_fancontrol rename to target/linux/kirkwood/base-files/etc/init.d/hwmon_fancontrol index 10eb5aa73c..0adc5d0726 100755 --- a/target/linux/kirkwood/base-files/etc/init.d/nsa310_fancontrol +++ b/target/linux/kirkwood/base-files/etc/init.d/hwmon_fancontrol @@ -4,17 +4,20 @@ START=98 boot() { . /lib/functions.sh -#configuring lm85 onboard temp/fan controller to run the fan on its own +#configuring (lm85/lm63) onboard temp/fan controller to run the fan on its own #for more information, please read https://www.kernel.org/doc/Documentation/hwmon/sysfs-interface -path_to_hwmon='/sys/devices/platform/ocp@f1000000/f1011000.i2c/i2c-0/0-002e/hwmon/hwmon0' - case $(board_name) in - zyxel,nsa310b) +zyxel,nsa310b) + path_to_hwmon='/sys/devices/platform/ocp@f1000000/f1011000.i2c/i2c-0/0-002e/hwmon/hwmon0' echo 2 > "$path_to_hwmon/pwm1_enable" # fan is on pwm1 echo 1 > "$path_to_hwmon/pwm1_auto_channels" # temp1 is the only one that changes echo 23000 > "$path_to_hwmon/temp1_auto_temp_min" echo 43000 > "$path_to_hwmon/temp1_auto_temp_max" # next step is 49600 millicelsius, or 50 celsius, 43 celsius is better - ;; + ;; +iom,ix2-200) + path_to_hwmon='/sys/class/hwmon/hwmon0' + echo 2 > "$path_to_hwmon/pwm1_enable" # fan is on pwm1 + ;; esac } diff --git a/target/linux/kirkwood/image/Makefile b/target/linux/kirkwood/image/Makefile index fdf86099bc..84e749f494 100644 --- a/target/linux/kirkwood/image/Makefile +++ b/target/linux/kirkwood/image/Makefile @@ -62,6 +62,22 @@ define Device/iom_iconnect-1.1 endef TARGET_DEVICES += iom_iconnect-1.1 +define Device/iom_ix2_200 + DEVICE_TITLE := Iomega StorCenter ix2-200 + DEVICE_DTS := kirkwood-iomega_ix2_200 + DEVICE_PACKAGES += kmod-gpio-button-hotplug kmod-i2c-mv64xxx kmod-hwmon-lm63 + DEVICE_TYPE:=nas + PAGESIZE := 512 + SUBPAGESIZE := 256 + BLOCKSIZE := 16KiB + KERNEL_SIZE := 3072k + KERNEL_IN_UBI := 0 + UBINIZE_OPTS := -E 5 + IMAGE_SIZE := 32505856 + IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | check-size $$$$(IMAGE_SIZE) +endef +TARGET_DEVICES += iom_ix2_200 + define Device/linksys_audi DEVICE_TITLE := Linksys EA3500 (Audi) DEVICE_PACKAGES := kmod-mwl8k swconfig wpad-mini kmod-gpio-button-hotplug diff --git a/target/linux/kirkwood/patches-4.14/103-iomega-ix2-200.patch b/target/linux/kirkwood/patches-4.14/103-iomega-ix2-200.patch new file mode 100644 index 0000000000..5b479aba4e --- /dev/null +++ b/target/linux/kirkwood/patches-4.14/103-iomega-ix2-200.patch @@ -0,0 +1,33 @@ +--- a/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts ++++ b/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts +@@ -185,18 +185,18 @@ + }; + + partition@a0000 { +- label = "env"; ++ label = "u-boot environment"; + reg = <0xa0000 0x20000>; + read-only; + }; + + partition@100000 { +- label = "uImage"; ++ label = "kernel"; + reg = <0x100000 0x300000>; + }; + + partition@400000 { +- label = "rootfs"; ++ label = "ubi"; + reg = <0x400000 0x1C00000>; + }; + }; +@@ -210,7 +210,7 @@ + }; + + ð0 { +- status = "okay"; ++ status = "disabled"; + ethernet0-port@0 { + speed = <1000>; + duplex = <1>; \ No newline at end of file diff --git a/target/linux/kirkwood/patches-4.9/103-iomega-ix2-200.patch b/target/linux/kirkwood/patches-4.9/103-iomega-ix2-200.patch new file mode 100644 index 0000000000..5b479aba4e --- /dev/null +++ b/target/linux/kirkwood/patches-4.9/103-iomega-ix2-200.patch @@ -0,0 +1,33 @@ +--- a/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts ++++ b/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts +@@ -185,18 +185,18 @@ + }; + + partition@a0000 { +- label = "env"; ++ label = "u-boot environment"; + reg = <0xa0000 0x20000>; + read-only; + }; + + partition@100000 { +- label = "uImage"; ++ label = "kernel"; + reg = <0x100000 0x300000>; + }; + + partition@400000 { +- label = "rootfs"; ++ label = "ubi"; + reg = <0x400000 0x1C00000>; + }; + }; +@@ -210,7 +210,7 @@ + }; + + ð0 { +- status = "okay"; ++ status = "disabled"; + ethernet0-port@0 { + speed = <1000>; + duplex = <1>; \ No newline at end of file -- 2.30.2