From 26ba9cd48fc0c2ff741de913270e9469506f3666 Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Thu, 24 Sep 2015 17:52:52 -0700 Subject: [PATCH] gpio: pl061: assign the apropriate handler for irqs The PL061 can handle level IRQs and edge IRQs, however it is just utilizing handle_simple_irq() for all IRQs. Inspired by Stefan Agners patch to vf610, this assigns the right handler depending on what type is set up, and after this handle_bad_irq() is only used as default and if the type is not specified, as is done in the OMAP driver: defining the IRQ type is really not optional for this driver. The interrupt handler was just writing the interrupt clearing register for all lines that were high when entering the handling loop, this is wrong: that register is only supposed to be written (on a per-line basis) for edge IRQs, so this ACK was moved to the .irq_ack() callback as is proper. Tested with PL061 on the ARM RealView PB11MPCore and the MMC/SC card detect GPIO. Cc: Jonas Gorski Cc: Stefan Agner Signed-off-by: Linus Walleij --- drivers/gpio/gpio-pl061.c | 30 +++++++++++++++++++++++++----- 1 file changed, 25 insertions(+), 5 deletions(-) diff --git a/drivers/gpio/gpio-pl061.c b/drivers/gpio/gpio-pl061.c index 179339739d60..e15499936c18 100644 --- a/drivers/gpio/gpio-pl061.c +++ b/drivers/gpio/gpio-pl061.c @@ -181,7 +181,7 @@ static int pl061_irq_type(struct irq_data *d, unsigned trigger) gpioiev |= bit; else gpioiev &= ~bit; - + irq_set_handler_locked(d, handle_level_irq); dev_dbg(gc->dev, "line %d: IRQ on %s level\n", offset, polarity ? "HIGH" : "LOW"); @@ -190,7 +190,7 @@ static int pl061_irq_type(struct irq_data *d, unsigned trigger) gpiois &= ~bit; /* Select both edges, setting this makes GPIOEV be ignored */ gpioibe |= bit; - + irq_set_handler_locked(d, handle_edge_irq); dev_dbg(gc->dev, "line %d: IRQ on both edges\n", offset); } else if ((trigger & IRQ_TYPE_EDGE_RISING) || (trigger & IRQ_TYPE_EDGE_FALLING)) { @@ -205,7 +205,7 @@ static int pl061_irq_type(struct irq_data *d, unsigned trigger) gpioiev |= bit; else gpioiev &= ~bit; - + irq_set_handler_locked(d, handle_edge_irq); dev_dbg(gc->dev, "line %d: IRQ on %s edge\n", offset, rising ? "RISING" : "FALLING"); @@ -214,6 +214,7 @@ static int pl061_irq_type(struct irq_data *d, unsigned trigger) gpiois &= ~bit; gpioibe &= ~bit; gpioiev &= ~bit; + irq_set_handler_locked(d, handle_bad_irq); dev_warn(gc->dev, "no trigger selected for line %d\n", offset); } @@ -238,7 +239,6 @@ static void pl061_irq_handler(struct irq_desc *desc) chained_irq_enter(irqchip, desc); pending = readb(chip->base + GPIOMIS); - writeb(pending, chip->base + GPIOIC); if (pending) { for_each_set_bit(offset, &pending, PL061_GPIO_NR) generic_handle_irq(irq_find_mapping(gc->irqdomain, @@ -274,8 +274,28 @@ static void pl061_irq_unmask(struct irq_data *d) spin_unlock(&chip->lock); } +/** + * pl061_irq_ack() - ACK an edge IRQ + * @d: IRQ data for this IRQ + * + * This gets called from the edge IRQ handler to ACK the edge IRQ + * in the GPIOIC (interrupt-clear) register. For level IRQs this is + * not needed: these go away when the level signal goes away. + */ +static void pl061_irq_ack(struct irq_data *d) +{ + struct gpio_chip *gc = irq_data_get_irq_chip_data(d); + struct pl061_gpio *chip = container_of(gc, struct pl061_gpio, gc); + u8 mask = BIT(irqd_to_hwirq(d) % PL061_GPIO_NR); + + spin_lock(&chip->lock); + writeb(mask, chip->base + GPIOIC); + spin_unlock(&chip->lock); +} + static struct irq_chip pl061_irqchip = { .name = "pl061", + .irq_ack = pl061_irq_ack, .irq_mask = pl061_irq_mask, .irq_unmask = pl061_irq_unmask, .irq_set_type = pl061_irq_type, @@ -338,7 +358,7 @@ static int pl061_probe(struct amba_device *adev, const struct amba_id *id) } ret = gpiochip_irqchip_add(&chip->gc, &pl061_irqchip, - irq_base, handle_simple_irq, + irq_base, handle_bad_irq, IRQ_TYPE_NONE); if (ret) { dev_info(&adev->dev, "could not add irqchip\n"); -- 2.30.2