From 200693f886d3765475fa264c4e03968e5f7e54b0 Mon Sep 17 00:00:00 2001 From: Mikhail Zhilkin Date: Sat, 2 Mar 2024 19:58:40 +0000 Subject: [PATCH] ramips: add support for Z-ROUTER ZR-2660 This commit adds support for Z-ROUTER ZR-2660 (also known as Routerich AX1800) wireless WiFi 6 router. Specification ------------- - SoC : MediaTek MT7621AT, MIPS, 880 MHz - RAM : 256 MiB - Flash : NAND 128 MiB (AMD/Spansion S34ML01G2) - WLAN : - 2.4 GHz : MediaTek MT7905D/MT7975 (14c3:7916), b/g/n/ax, MIMO 2x2 - 5 GHz : MediaTek MT7915E (14c3:7915), a/n/ac/ax, MIMO 2x2 - Ethernet : 10/100/1000 Mbps x4 (1x WAN, 3x LAN) - USB : 1x 2.0 - UART : 3.3V, 115200n8, pins are silkscreened on the pcb - Buttons : 1x Reset - LEDs : 1x WiFi 2.4 GHz (green) 1x WiFi 5 GHz (green) 1x LAN (green) 1x WAN (green) 1x WAN no-internet (red) - Power : 12 VDC, 1 A Installation ------------ 1. Run tftp server on your PC (IP: 192.168.2.2) and put OpenWrt initramfs image (initramfs.bin) to the tftp root dir 2. Open the following link in the browser to enable telnet: http://192.168.2.1/cgi-bin/telnet_ssh 3. Connect to the router (default IP: 192.168.2.1) using telnet shell (credentials - user:admin) 4. Run the following commands in the telnet shell (this will install OpenWrt initramfs image on nand flash): cd /tmp tftp -g -r initramfs.bin 192.168.2.2 mtd write initramfs.bin firmware mtd erase firmware_backup reboot 5. Copy OpenWrt sysupgrade image (sysupgrade.bin) to the /tmp dir of the router 6. Connect to the router (IP: 192.168.1.1) using ssh shell and run sysupgrade command: sysupgrade -n /tmp/sysupgrade.bin Return to stock --------------- 1. Copy stock firmware (stock.bin) to the /tmp dir of the router using scp 2. Run following command in the router shell: cd /tmp mtd write stock.bin firmware reboot Recovery -------- Connect uart (pins are silkscreened on the pcb), interrupt boot process by pressing any key, use u-boot menu to flash stock firmware image or OpenWrt initramfs image. MAC addresses ------------- +---------+-------------------+-----------+ | | MAC | Algorithm | +---------+-------------------+-----------+ | LAN | 24:0f:5e:xx:xx:4c | label | | WAN | 24:0f:5e:xx:xx:4d | label+1 | | WLAN 2g | 24:0f:5e:xx:xx:4e | label+2 | | WLAN 5g | 24:0f:5e:xx:xx:4f | label+3 | +---------+-------------------+-----------+ The WLAN 2.4 MAC was found in 'factory', 0x4 The LAN MAC was found in 'factory', 0xfff4 The WAN MAC was found in 'factory', 0xfffa Signed-off-by: Mikhail Zhilkin (cherry picked from commit 1d3d6ef8269aca7ee34fb6ddd1c11d3fe45e785b) Signed-off-by: Mikhail Zhilkin --- .../ramips/dts/mt7621_z-router_zr-2660.dts | 211 ++++++++++++++++++ target/linux/ramips/image/mt7621.mk | 15 ++ .../mt7621/base-files/etc/board.d/01_leds | 5 + .../mt7621/base-files/etc/board.d/02_network | 1 + .../etc/hotplug.d/ieee80211/10_fix_wifi_mac | 3 +- .../mt7621/base-files/lib/upgrade/platform.sh | 1 + 6 files changed, 235 insertions(+), 1 deletion(-) create mode 100644 target/linux/ramips/dts/mt7621_z-router_zr-2660.dts diff --git a/target/linux/ramips/dts/mt7621_z-router_zr-2660.dts b/target/linux/ramips/dts/mt7621_z-router_zr-2660.dts new file mode 100644 index 0000000000..34b151be75 --- /dev/null +++ b/target/linux/ramips/dts/mt7621_z-router_zr-2660.dts @@ -0,0 +1,211 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "mt7621.dtsi" + +#include +#include +#include + +/ { + compatible = "z-router,zr-2660", "mediatek,mt7621-soc"; + model = "Z-ROUTER ZR-2660"; + + aliases { + label-mac-device = &gmac0; + + led-boot = &led_power_green; + led-failsafe = &led_power_green; + led-running = &led_power_green; + led-upgrade = &led_power_green; + }; + + chosen { + bootargs = "console=ttyS0,115200"; + }; + + keys { + compatible = "gpio-keys"; + + key-0 { + label = "reset"; + gpios = <&gpio 18 GPIO_ACTIVE_LOW>; + linux,code = ; + debounce-interval = <60>; + }; + }; + + leds { + compatible = "gpio-leds"; + + led-0 { + color = ; + function = LED_FUNCTION_WAN; + gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + }; + + led-1 { + color = ; + function = LED_FUNCTION_WLAN; + function-enumerator = <50>; + gpios = <&gpio 13 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy1tpt"; + }; + + led-2 { + color = ; + function = LED_FUNCTION_LAN; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + }; + + led-3 { + color = ; + function = LED_FUNCTION_WLAN; + function-enumerator = <24>; + gpios = <&gpio 15 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + + led-4 { + color = ; + function = LED_FUNCTION_WAN; + gpios = <&gpio 16 GPIO_ACTIVE_HIGH>; + }; + + led_power_green: led-5 { + color = ; + function = LED_FUNCTION_POWER; + gpios = <&gpio 17 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&gmac0 { + nvmem-cells = <&macaddr_factory_3fff4>; + nvmem-cell-names = "mac-address"; +}; + +&gmac1 { + status = "okay"; + label = "wan"; + phy-handle = <ðphy4>; + + nvmem-cells = <&macaddr_factory_3fffa>; + nvmem-cell-names = "mac-address"; +}; + +&mdio { + ethphy4: ethernet-phy@4 { + reg = <4>; + }; +}; + +&nand { + status = "okay"; + + mediatek,nmbm; + mediatek,bmt-max-ratio = <1>; + mediatek,bmt-max-reserved-blocks = <64>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x80000>; + read-only; + }; + + partition@80000 { + label = "Config"; + reg = <0x80000 0x80000>; + read-only; + }; + + partition@100000 { + label = "factory"; + reg = <0x100000 0x80000>; + read-only; + + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + eeprom_factory_0: eeprom@0 { + reg = <0x0 0xe00>; + }; + + macaddr_factory_3fff4: macaddr@3fff4 { + reg = <0x3fff4 0x6>; + }; + + macaddr_factory_3fffa: macaddr@3fffa { + reg = <0x3fffa 0x6>; + }; + }; + }; + + partition@180000 { + label = "firmware"; + reg = <0x180000 0x7680000>; + + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "kernel"; + reg = <0x0 0x400000>; + }; + + partition@400000 { + label = "ubi"; + reg = <0x400000 0x7280000>; + }; + }; + }; +}; + +&pcie { + status = "okay"; +}; + +&pcie1 { + wifi@0,0 { + compatible = "mediatek,mt76"; + reg = <0x0000 0 0 0 0>; + + mediatek,disable-radar-background; + + nvmem-cells = <&eeprom_factory_0>; + nvmem-cell-names = "eeprom"; + }; +}; + +&state_default { + gpio { + groups = "i2c", "jtag", "wdt"; + function = "gpio"; + }; +}; + +&switch0 { + ports { + port@1 { + status = "okay"; + label = "lan1"; + }; + + port@2 { + status = "okay"; + label = "lan2"; + }; + + port@3 { + status = "okay"; + label = "lan3"; + }; + }; +}; diff --git a/target/linux/ramips/image/mt7621.mk b/target/linux/ramips/image/mt7621.mk index 2800eea681..1a8df617b5 100644 --- a/target/linux/ramips/image/mt7621.mk +++ b/target/linux/ramips/image/mt7621.mk @@ -2816,6 +2816,21 @@ define Device/yuncore_g720 endef TARGET_DEVICES += yuncore_g720 +define Device/z-router_zr-2660 + $(Device/dsa-migration) + $(Device/nand) + DEVICE_VENDOR := Z-ROUTER + DEVICE_MODEL := ZR-2660 + DEVICE_ALT0_VENDOR := Routerich + DEVICE_ALT0_MODEL := AX1800 + IMAGE_SIZE := 90112k + KERNEL_LOADADDR := 0x82000000 + KERNEL := kernel-bin | relocate-kernel $(loadaddr-y) | lzma | \ + fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb + DEVICE_PACKAGES += kmod-mt7915-firmware kmod-usb3 -uboot-envtools +endef +TARGET_DEVICES += z-router_zr-2660 + define Device/zbtlink_zbt-we1326 $(Device/dsa-migration) $(Device/uimage-lzma-loader) diff --git a/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds b/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds index a721833040..ae46ddb79f 100644 --- a/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds +++ b/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds @@ -246,6 +246,11 @@ yuncore,ax820) ucidef_set_led_netdev "lan" "LAN" "green:lan" "lan" ucidef_set_led_netdev "wan" "WAN" "green:wan" "wan" ;; +z-router,zr-2660) + ucidef_set_led_netdev "lan" "lan" "green:lan" "br-lan" "link tx rx" + ucidef_set_led_netdev "wan" "wan" "green:wan" "wan" "link tx rx" + ucidef_set_led_netdev "wan-off" "wan-off" "red:wan" "wan" "link" + ;; zyxel,lte3301-plus) ucidef_set_led_netdev "internet" "internet" "white:internet" "wwan0" ;; diff --git a/target/linux/ramips/mt7621/base-files/etc/board.d/02_network b/target/linux/ramips/mt7621/base-files/etc/board.d/02_network index 041df7677e..8aabf41928 100644 --- a/target/linux/ramips/mt7621/base-files/etc/board.d/02_network +++ b/target/linux/ramips/mt7621/base-files/etc/board.d/02_network @@ -26,6 +26,7 @@ ramips_setup_interfaces() xiaomi,mi-router-cr6608|\ xiaomi,mi-router-cr6609|\ xiaomi,redmi-router-ac2100|\ + z-router,zr-2660|\ zyxel,wsm20) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" "wan" ;; diff --git a/target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac b/target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac index 353bd31233..0e4541a421 100644 --- a/target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac +++ b/target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac @@ -71,7 +71,8 @@ case "$board" in macaddr_setbit_la "$base_mac" > /sys${DEVPATH}/macaddress fi ;; - glinet,gl-mt1300) + glinet,gl-mt1300|\ + z-router,zr-2660) [ "$PHYNBR" = "1" ] && \ macaddr_add "$(mtd_get_mac_binary factory 0x4)" 1 > /sys${DEVPATH}/macaddress ;; diff --git a/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh b/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh index 98d26cc904..8b35b5d32a 100755 --- a/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh +++ b/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh @@ -118,6 +118,7 @@ platform_do_upgrade() { xiaomi,mi-router-cr6608|\ xiaomi,mi-router-cr6609|\ xiaomi,redmi-router-ac2100|\ + z-router,zr-2660|\ zyxel,nwa50ax|\ zyxel,nwa55axe) nand_do_upgrade "$1" -- 2.30.2