From 18bea173a646518a64ca05ea26f87eab0540feb9 Mon Sep 17 00:00:00 2001 From: Chen Minqiang Date: Tue, 13 Sep 2022 13:46:20 +0800 Subject: [PATCH] mediatek: add alternative stock layout for Xiaomi Redmi Router AX6000 In this implementation, the flash partition layout is adjusted to avoid modifying the uboot environment of mtdparts. This ensures that the 30M ubi_kernel partition remains aligned with the stock ubi partition, and the kernel volume is placed in it. This allows the stock uboot to boot from it without changing the mtdparts, which is useful for reverting back to the stock firmware using Xiaomi Firmware Tools. In actual testing, modifying mtdparts has been found to break Xiaomi Firmware Tools. 1. use ARTIFACTS to generate initramfs-factory.ubi for easy installation. 2. The NAND flash layout is changed to allow for reverting back to the stock firmware. 3. Before performing sysupgrade, do some cleanup in platform_pre_upgrade to ensure a clean installation of OpenWRT. 4. Setup the uboot env to ensure that the system always boot, which can be helpful for users who may forget to do this before sysupgrade in the initramfs. New flash instructions: 1. Gain ssh access. Please refer to: https://openwrt.org/toh/xiaomi/redmi_ax6000#installation) 2. Check which system current u-boot is loading from: COMMAND: `cat /proc/cmdline` sample OUTPUT: `console=ttyS0,115200n1 loglevel=8 firmware=1 uart_en=1` if firmware=1, current system is ubi1 if firmware=0, current system is ubi0 3. Setup nvram and write the firmware: If the current system is ubi1, please set it up so that the next time it will boot from ubi, and write the firmware to ubi: ``` nvram set boot_wait=on nvram set uart_en=1 nvram set flag_boot_rootfs=0 nvram set flag_last_success=0 nvram set flag_boot_success=1 nvram set flag_try_sys1_failed=0 nvram set flag_try_sys2_failed=0 nvram commit ubiformat /dev/mtd8 -y -f /tmp/initramfs-factory.ubi ``` If the current system is ubi, please set it up so that the next time it will boot from ubi1, and write the firmware to ubi1: ``` nvram set boot_wait=on nvram set uart_en=1 nvram set flag_boot_rootfs=1 nvram set flag_last_success=1 nvram set flag_boot_success=1 nvram set flag_try_sys1_failed=0 nvram set flag_try_sys2_failed=0 nvram commit ubiformat /dev/mtd9 -y -f /tmp/initramfs-factory.ubi ``` 4. After rebooting, the system should now boot into the openwrt initramfs. Flash the squashfs-sysupgrade.bin via using ssh or luci. ``` sysupgrade -n /tmp/squashfs-sysupgrade.bin ``` Done. For existing users of the Redmi AX6000 running OpenWrt, here are the steps to switch to this new layout: 1. Flash initramfs-factory.ubi ``` mtd -r -e ubi write /tmp/initramfs-factory.ubi ubi ``` 2. After rebooting, the system will boot into the new openwrt-initramfs. Log in and perform a sysupgrade to complete the process. ``` sysupgrade -n /tmp/squashfs-sysupgrade.bin ``` Signed-off-by: Chen Minqiang Signed-off-by: Chuanhong Guo --- .../uboot-envtools/files/mediatek_filogic | 3 +- ...7986a-xiaomi-redmi-router-ax6000-stock.dts | 21 ++ .../mt7986a-xiaomi-redmi-router-ax6000.dts | 293 +----------------- .../mt7986a-xiaomi-redmi-router-ax6000.dtsi | 277 +++++++++++++++++ .../filogic/base-files/etc/board.d/01_leds | 3 +- .../filogic/base-files/etc/board.d/02_network | 6 +- .../base-files/lib/upgrade/platform.sh | 53 ++++ target/linux/mediatek/image/filogic.mk | 18 ++ 8 files changed, 389 insertions(+), 285 deletions(-) create mode 100644 target/linux/mediatek/dts/mt7986a-xiaomi-redmi-router-ax6000-stock.dts create mode 100644 target/linux/mediatek/dts/mt7986a-xiaomi-redmi-router-ax6000.dtsi diff --git a/package/boot/uboot-envtools/files/mediatek_filogic b/package/boot/uboot-envtools/files/mediatek_filogic index fe986b2e4ea..f73ea80109a 100644 --- a/package/boot/uboot-envtools/files/mediatek_filogic +++ b/package/boot/uboot-envtools/files/mediatek_filogic @@ -34,7 +34,8 @@ bananapi,bpi-r3) ;; esac ;; -xiaomi,redmi-router-ax6000) +xiaomi,redmi-router-ax6000|\ +xiaomi,redmi-router-ax6000-stock) ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x10000" "0x20000" ubootenv_add_uci_sys_config "/dev/mtd2" "0x0" "0x10000" "0x20000" ;; diff --git a/target/linux/mediatek/dts/mt7986a-xiaomi-redmi-router-ax6000-stock.dts b/target/linux/mediatek/dts/mt7986a-xiaomi-redmi-router-ax6000-stock.dts new file mode 100644 index 00000000000..64342677b38 --- /dev/null +++ b/target/linux/mediatek/dts/mt7986a-xiaomi-redmi-router-ax6000-stock.dts @@ -0,0 +1,21 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) + +/dts-v1/; +#include "mt7986a-xiaomi-redmi-router-ax6000.dtsi" + +/ { + model = "Xiaomi Redmi Router AX6000 (stock layout)"; + compatible = "xiaomi,redmi-router-ax6000-stock", "mediatek,mt7986a"; +}; + +&partitions { + partition@600000 { + label = "ubi_kernel"; + reg = <0x600000 0x1e00000>; + }; + + partition@2400000 { + label = "ubi"; + reg = <0x2400000 0x5000000>; + }; +}; diff --git a/target/linux/mediatek/dts/mt7986a-xiaomi-redmi-router-ax6000.dts b/target/linux/mediatek/dts/mt7986a-xiaomi-redmi-router-ax6000.dts index 31112664c2e..a8df7866320 100644 --- a/target/linux/mediatek/dts/mt7986a-xiaomi-redmi-router-ax6000.dts +++ b/target/linux/mediatek/dts/mt7986a-xiaomi-redmi-router-ax6000.dts @@ -1,293 +1,24 @@ // SPDX-License-Identifier: (GPL-2.0 OR MIT) /dts-v1/; -#include -#include -#include - -#include "mt7986a.dtsi" +#include "mt7986a-xiaomi-redmi-router-ax6000.dtsi" / { model = "Xiaomi Redmi Router AX6000"; compatible = "xiaomi,redmi-router-ax6000", "mediatek,mt7986a"; - - aliases { - serial0 = &uart0; - led-boot = &led_status_rgb; - led-failsafe = &led_status_rgb; - led-running = &led_status_rgb; - led-upgrade = &led_status_rgb; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - memory { - reg = <0 0x40000000 0 0x20000000>; - }; - - keys { - compatible = "gpio-keys"; - - reset { - label = "reset"; - gpios = <&pio 9 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - mesh { - label = "mesh"; - gpios = <&pio 10 GPIO_ACTIVE_LOW>; - linux,code = ; - linux,input-type = ; - }; - }; -}; - -ð { - status = "okay"; - - gmac0: mac@0 { - compatible = "mediatek,eth-mac"; - reg = <0>; - phy-mode = "2500base-x"; - - nvmem-cells = <&macaddr_factory_4>; - nvmem-cell-names = "mac-address"; - mac-address-increment = <(-1)>; - - fixed-link { - speed = <2500>; - full-duplex; - pause; - }; - }; - - mdio: mdio-bus { - #address-cells = <1>; - #size-cells = <0>; - }; -}; - -&mdio { - switch: switch@0 { - compatible = "mediatek,mt7531"; - reg = <31>; - reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>; - interrupt-controller; - #interrupt-cells = <1>; - interrupt-parent = <&pio>; - interrupts = <66 IRQ_TYPE_LEVEL_HIGH>; - }; }; -&pio { - spi_flash_pins: spi-flash-pins-33-to-38 { - mux { - function = "spi"; - groups = "spi0", "spi0_wp_hold"; - }; - conf-pu { - pins = "SPI2_CS", "SPI2_HOLD", "SPI2_WP"; - drive-strength = <8>; - mediatek,pull-up-adv = <0>; /* bias-disable */ - }; - conf-pd { - pins = "SPI2_CLK", "SPI2_MOSI", "SPI2_MISO"; - drive-strength = <8>; - mediatek,pull-down-adv = <0>; /* bias-disable */ - }; - }; - - spi_led_pins: spic-pins-29-to-32 { - mux { - function = "spi"; - groups = "spi1_2"; - }; +&partitions { + /* ubi partition is the result of squashing + * consecutive stock partitions: + * - ubi + * - ubi1 + * - overlay + */ + partition@600000 { + label = "ubi"; + reg = <0x600000 0x6e00000>; }; - wf_2g_5g_pins: wf_2g_5g-pins { - mux { - function = "wifi"; - groups = "wf_2g", "wf_5g"; - }; - conf { - pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4", - "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6", - "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10", - "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1", - "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0", - "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8", - "WF1_TOP_CLK", "WF1_TOP_DATA"; - drive-strength = <4>; - }; - }; -}; - -&spi0 { - pinctrl-names = "default"; - pinctrl-0 = <&spi_flash_pins>; - cs-gpios = <0>, <0>; - status = "okay"; - - flash@0 { - compatible = "spi-nand"; - #address-cells = <1>; - #size-cells = <1>; - reg = <0>; - - mediatek,nmbm; - mediatek,bmt-max-ratio = <1>; - mediatek,bmt-max-reserved-blocks = <64>; - - spi-max-frequency = <20000000>; - spi-tx-buswidth = <4>; - spi-rx-buswidth = <4>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "BL2"; - reg = <0x0 0x100000>; - read-only; - }; - - partition@100000 { - label = "Nvram"; - reg = <0x100000 0x40000>; - }; - - partition@140000 { - label = "Bdata"; - reg = <0x140000 0x40000>; - }; - - factory: partition@180000 { - label = "Factory"; - reg = <0x180000 0x200000>; - read-only; - - compatible = "nvmem-cells"; - #address-cells = <1>; - #size-cells = <1>; - - macaddr_factory_4: macaddr@4 { - reg = <0x4 0x6>; - }; - }; - - partition@380000 { - label = "FIP"; - reg = <0x380000 0x200000>; - read-only; - }; - - partition@580000 { - label = "crash"; - reg = <0x580000 0x40000>; - read-only; - }; - - partition@5c0000 { - label = "crash_log"; - reg = <0x5c0000 0x40000>; - read-only; - }; - - /* ubi partition is the result of squashing - * consecutive stock partitions: - * - ubi - * - ubi1 - * - overlay - */ - partition@600000 { - label = "ubi"; - reg = <0x600000 0x6e00000>; - }; - - /* last 12 MiB is reserved for NMBM bad block table */ - }; - }; -}; - -&spi1 { - pinctrl-names = "default"; - pinctrl-0 = <&spi_led_pins>; - status = "okay"; - - ws2812b@0 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "worldsemi,ws2812b"; - reg = <0>; - spi-max-frequency = <3000000>; - - led_status_rgb: led@0 { - reg = <0>; - label = "rgb:status"; - color-index = ; - }; - - led_network_rgb: led@1 { - reg = <1>; - label = "rgb:network"; - color-index = ; - }; - }; -}; - -&switch { - ports { - #address-cells = <1>; - #size-cells = <0>; - - port@1 { - reg = <1>; - label = "lan4"; - }; - - port@2 { - reg = <2>; - label = "lan3"; - }; - - port@3 { - reg = <3>; - label = "lan2"; - }; - - port@4 { - reg = <4>; - label = "wan"; - }; - - port@6 { - reg = <6>; - label = "cpu"; - ethernet = <&gmac0>; - phy-mode = "2500base-x"; - - fixed-link { - speed = <2500>; - full-duplex; - pause; - }; - }; - }; -}; - -&wmac { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&wf_2g_5g_pins>; - - mediatek,mtd-eeprom = <&factory 0x0>; -}; - -&uart0 { - status = "okay"; + /* last 12 MiB is reserved for NMBM bad block table */ }; diff --git a/target/linux/mediatek/dts/mt7986a-xiaomi-redmi-router-ax6000.dtsi b/target/linux/mediatek/dts/mt7986a-xiaomi-redmi-router-ax6000.dtsi new file mode 100644 index 00000000000..4b2754b0012 --- /dev/null +++ b/target/linux/mediatek/dts/mt7986a-xiaomi-redmi-router-ax6000.dtsi @@ -0,0 +1,277 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) + +/dts-v1/; +#include +#include +#include + +#include "mt7986a.dtsi" + +/ { + aliases { + serial0 = &uart0; + led-boot = &led_status_rgb; + led-failsafe = &led_status_rgb; + led-running = &led_status_rgb; + led-upgrade = &led_status_rgb; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory { + reg = <0 0x40000000 0 0x20000000>; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&pio 9 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + mesh { + label = "mesh"; + gpios = <&pio 10 GPIO_ACTIVE_LOW>; + linux,code = ; + linux,input-type = ; + }; + }; +}; + +ð { + status = "okay"; + + gmac0: mac@0 { + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-mode = "2500base-x"; + + nvmem-cells = <&macaddr_factory_4>; + nvmem-cell-names = "mac-address"; + mac-address-increment = <(-1)>; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + + mdio: mdio-bus { + #address-cells = <1>; + #size-cells = <0>; + }; +}; + +&mdio { + switch: switch@0 { + compatible = "mediatek,mt7531"; + reg = <31>; + reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>; + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&pio>; + interrupts = <66 IRQ_TYPE_LEVEL_HIGH>; + }; +}; + +&pio { + spi_flash_pins: spi-flash-pins-33-to-38 { + mux { + function = "spi"; + groups = "spi0", "spi0_wp_hold"; + }; + conf-pu { + pins = "SPI2_CS", "SPI2_HOLD", "SPI2_WP"; + drive-strength = <8>; + mediatek,pull-up-adv = <0>; /* bias-disable */ + }; + conf-pd { + pins = "SPI2_CLK", "SPI2_MOSI", "SPI2_MISO"; + drive-strength = <8>; + mediatek,pull-down-adv = <0>; /* bias-disable */ + }; + }; + + spi_led_pins: spic-pins-29-to-32 { + mux { + function = "spi"; + groups = "spi1_2"; + }; + }; + + wf_2g_5g_pins: wf_2g_5g-pins { + mux { + function = "wifi"; + groups = "wf_2g", "wf_5g"; + }; + conf { + pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4", + "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6", + "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10", + "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1", + "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0", + "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8", + "WF1_TOP_CLK", "WF1_TOP_DATA"; + drive-strength = <4>; + }; + }; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi_flash_pins>; + cs-gpios = <0>, <0>; + status = "okay"; + + flash@0 { + compatible = "spi-nand"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0>; + + mediatek,nmbm; + mediatek,bmt-max-ratio = <1>; + mediatek,bmt-max-reserved-blocks = <64>; + + spi-max-frequency = <20000000>; + spi-tx-buswidth = <4>; + spi-rx-buswidth = <4>; + + partitions: partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "BL2"; + reg = <0x0 0x100000>; + read-only; + }; + + partition@100000 { + label = "Nvram"; + reg = <0x100000 0x40000>; + }; + + partition@140000 { + label = "Bdata"; + reg = <0x140000 0x40000>; + }; + + factory: partition@180000 { + label = "Factory"; + reg = <0x180000 0x200000>; + read-only; + + compatible = "nvmem-cells"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_factory_4: macaddr@4 { + reg = <0x4 0x6>; + }; + }; + + partition@380000 { + label = "FIP"; + reg = <0x380000 0x200000>; + read-only; + }; + + partition@580000 { + label = "crash"; + reg = <0x580000 0x40000>; + read-only; + }; + + partition@5c0000 { + label = "crash_log"; + reg = <0x5c0000 0x40000>; + read-only; + }; + }; + }; +}; + +&spi1 { + pinctrl-names = "default"; + pinctrl-0 = <&spi_led_pins>; + status = "okay"; + + ws2812b@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "worldsemi,ws2812b"; + reg = <0>; + spi-max-frequency = <3000000>; + + led_status_rgb: led@0 { + reg = <0>; + label = "rgb:status"; + color-index = ; + }; + + led_network_rgb: led@1 { + reg = <1>; + label = "rgb:network"; + color-index = ; + }; + }; +}; + +&switch { + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + reg = <1>; + label = "lan4"; + }; + + port@2 { + reg = <2>; + label = "lan3"; + }; + + port@3 { + reg = <3>; + label = "lan2"; + }; + + port@4 { + reg = <4>; + label = "wan"; + }; + + port@6 { + reg = <6>; + label = "cpu"; + ethernet = <&gmac0>; + phy-mode = "2500base-x"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + }; +}; + +&wmac { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&wf_2g_5g_pins>; + + mediatek,mtd-eeprom = <&factory 0x0>; +}; + +&uart0 { + status = "okay"; +}; diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds index f851c7ed54b..8cfed15544d 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds @@ -6,7 +6,8 @@ board=$(board_name) board_config_update case $board in -xiaomi,redmi-router-ax6000) +xiaomi,redmi-router-ax6000|\ +xiaomi,redmi-router-ax6000-stock) ucidef_set_led_netdev "wan" "wan" "rgb:network" "wan" ;; esac diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network index 0f0a0fc86b1..1c98dcc7cb3 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network @@ -16,7 +16,8 @@ mediatek_setup_interfaces() ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 sfp2" "eth1 wan" ucidef_set_interface_macaddr "wan" "$(macaddr_add $(cat /sys/class/net/eth0/address) 1)" ;; - xiaomi,redmi-router-ax6000) + xiaomi,redmi-router-ax6000|\ + xiaomi,redmi-router-ax6000-stock) ucidef_set_interfaces_lan_wan "lan2 lan3 lan4" wan ;; *) @@ -33,7 +34,8 @@ mediatek_setup_macs() local label_mac="" case $board in - xiaomi,redmi-router-ax6000) + xiaomi,redmi-router-ax6000|\ + xiaomi,redmi-router-ax6000-stock) wan_mac=$(mtd_get_mac_ascii Bdata ethaddr_wan) label_mac=$wan_mac ;; diff --git a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh index a9327ae282a..29c7a1475ed 100755 --- a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh +++ b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh @@ -1,5 +1,43 @@ REQUIRE_IMAGE_METADATA=1 +redmi_ax6000_initial_setup() +{ + # initialize UBI and setup uboot-env if it's running on initramfs + [ "$(rootfs_type)" = "tmpfs" ] || return 0 + + local mtdnum="$( find_mtd_index ubi )" + if [ ! "$mtdnum" ]; then + echo "unable to find mtd partition ubi" + return 1 + fi + + local kern_mtdnum="$( find_mtd_index ubi_kernel )" + if [ ! "$kern_mtdnum" ]; then + echo "unable to find mtd partition ubi_kernel" + return 1 + fi + + ubidetach -m "$mtdnum" + ubiformat /dev/mtd$mtdnum -y + + ubidetach -m "$kern_mtdnum" + ubiformat /dev/mtd$kern_mtdnum -y + + if ! fw_printenv -n flag_try_sys2_failed &>/dev/null; then + echo "failed to access u-boot-env. skip env setup." + return 0 + fi + + fw_setenv boot_wait on + fw_setenv uart_en 1 + fw_setenv flag_boot_rootfs 0 + fw_setenv flag_last_success 1 + fw_setenv flag_boot_success 1 + fw_setenv flag_try_sys1_failed 8 + fw_setenv flag_try_sys2_failed 8 + fw_setenv mtdparts "nmbm0:1024k(bl2),256k(Nvram),256k(Bdata),2048k(factory),2048k(fip),256k(crash),256k(crash_log),30720k(ubi),30720k(ubi1),51200k(overlay)" +} + platform_do_upgrade() { local board=$(board_name) @@ -21,6 +59,11 @@ platform_do_upgrade() { ;; esac ;; + xiaomi,redmi-router-ax6000-stock) + CI_KERN_UBIPART=ubi_kernel + CI_ROOT_UBIPART=ubi + nand_do_upgrade "$1" + ;; *) nand_do_upgrade "$1" ;; @@ -63,3 +106,13 @@ platform_copy_config() { ;; esac } + +platform_pre_upgrade() { + local board=$(board_name) + + case "$board" in + xiaomi,redmi-router-ax6000-stock) + redmi_ax6000_initial_setup + ;; + esac +} diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk index 5dbeedb64c7..4e3399d120b 100644 --- a/target/linux/mediatek/image/filogic.mk +++ b/target/linux/mediatek/image/filogic.mk @@ -139,3 +139,21 @@ define Device/xiaomi_redmi-router-ax6000 IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata endef TARGET_DEVICES += xiaomi_redmi-router-ax6000 + +define Device/xiaomi_redmi-router-ax6000-stock + DEVICE_VENDOR := Xiaomi + DEVICE_MODEL := Redmi Router AX6000 (stock layout) + DEVICE_DTS := mt7986a-xiaomi-redmi-router-ax6000-stock + DEVICE_DTS_DIR := ../dts + DEVICE_PACKAGES := kmod-leds-ws2812b + KERNEL_LOADADDR := 0x48000000 + UBINIZE_OPTS := -E 5 + BLOCKSIZE := 128k + PAGESIZE := 2048 +ifneq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),) + ARTIFACTS := initramfs-factory.ubi + ARTIFACT/initramfs-factory.ubi := append-image-stage initramfs-kernel.bin | ubinize-kernel +endif + IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata +endef +TARGET_DEVICES += xiaomi_redmi-router-ax6000-stock -- 2.30.2