From 0a18259e4aa361cd9e5848c038be4b9f4e3bfcc6 Mon Sep 17 00:00:00 2001 From: Roland Reinl Date: Fri, 3 Nov 2023 11:22:02 +0100 Subject: [PATCH] ramips: add support for D-Link COVR-X1860 A1 The COVR-X1860 are MT7621-based AX1800 devices (similar to DAP-X1860, but with two Ethernet ports and external power supply) that are sold in sets of two (COVR-X1862) and three (COVR-X1863). Specification: - MT7621 - MT7915 + MT7975 2x2 802.11ax (DBDC) - 256MB RAM - 128 MB flash - 3 LEDs (red, orange, white), routed to one indicator in the top of the device - 2 buttons (WPS in the back and Reset at the bottom of the device) MAC addresses: - LAN MAC (printed on the device) is stored in config2 partition as ASCII (entry factory_mac=xx:xx:xx:xx:xx:xx) - WAN MAC: LAN MAC + 3 - 2.4G MAC: LAN MAC + 1 - 5G MAC: LAN MAC + 2 The pins for the serial console are already labeled on the board (VCC, TX, RX, GND). Serial settings: 3.3V, 115200,8n1 Flashing via OEM Web Interface: - Download openwrt-ramips-mt7621-dlink_covr-x1860-a1-squashfs-factory.bin via the OEM web interface firmware update - The configuration wizard can be skipped by directly going to http://192.168.0.1/UpdateFirmware_Simple.html Flashing via Recovery Web Interface: - Set your IP address to 192.168.0.10, subnetmask 255.255.255.0 - Press the reset button while powering on the deivce - Keep the reset button pressed until the status LED blinks red - Open a Chromium based browser and goto http://192.168.0.1 - Download openwrt-ramips-mt7621-dlink_covr-x1860-a1-squashfs-recovery.bin Revert back to stock using the Recovery Web Interface: - Set your IP address to 192.168.0.10, subnetmask 255.255.255.25 - Press the reset button while powering on the deivce - Keep the reset button pressed until the status LED blinks red - Open a Chromium based browser and goto http://192.168.0.1 - Flash a decrypted firmware image from D-Link. Decrypting an firmware image is described below. Decrypting a D-Link firmware image: - Download https://github.com/openwrt/firmware-utils/blob/master/src/dlink-sge-image.c and https://raw.githubusercontent.com/openwrt/firmware-utils/master/src/dlink-sge-image.h - Compile a binary from the downloaded file, e.g. gcc dlink-sge-image.c -lcrypto -o dlink-sge-image - Run ./dlink-sge-image COVR-X1860 -d - Example for firmware 102b01: ./dlink-sge-image COVR-X1860 COVR-X1860_RevA_Firmware_102b01.bin COVR-X1860_RevA_Firmware_102b01_Decrypted.bin -d The pull request is based on the discussion in https://forum.openwrt.org/t/add-support-for-d-link-covr-x1860 Signed-off-by: Sebastian Schaper Signed-off-by: Roland Reinl --- .../ramips/dts/mt7621_dlink_covr-x1860-a1.dts | 186 ++++++++++++++++++ target/linux/ramips/image/mt7621.mk | 33 ++++ .../mt7621/base-files/etc/board.d/02_network | 8 + .../etc/hotplug.d/ieee80211/10_fix_wifi_mac | 7 + .../mt7621/base-files/lib/upgrade/platform.sh | 1 + 5 files changed, 235 insertions(+) create mode 100644 target/linux/ramips/dts/mt7621_dlink_covr-x1860-a1.dts diff --git a/target/linux/ramips/dts/mt7621_dlink_covr-x1860-a1.dts b/target/linux/ramips/dts/mt7621_dlink_covr-x1860-a1.dts new file mode 100644 index 0000000000..c06c5e36ba --- /dev/null +++ b/target/linux/ramips/dts/mt7621_dlink_covr-x1860-a1.dts @@ -0,0 +1,186 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "mt7621.dtsi" + +#include +#include + +/ { + compatible = "dlink,covr-x1860-a1", "mediatek,mt7621-soc"; + model = "D-Link COVR-X1860 A1"; + + aliases { + led-boot = &status_orange; + led-failsafe = &status_red; + led-running = &status_white; + led-upgrade = &status_red; + }; + + chosen { + bootargs = "console=ttyS0,115200"; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + linux,code = ; + gpios = <&gpio 15 GPIO_ACTIVE_LOW>; + }; + + wps { + label = "wps"; + linux,code = ; + gpios = <&gpio 8 GPIO_ACTIVE_LOW>; + }; + }; + + leds { + compatible = "gpio-leds"; + + status_white: power { + label = "white:status"; + gpios = <&gpio 16 GPIO_ACTIVE_LOW>; + }; + + status_orange: status_orange { + label = "orange:status"; + gpios = <&gpio 13 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + + status_red: status_red { + label = "red:status"; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + }; + }; + + virtual_flash { + compatible = "mtd-concat"; + + devices = <&fwconcat0 &fwconcat1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "ubi"; + reg = <0x0 0x0>; + }; + }; + }; +}; + +&nand { + status = "okay"; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "bootloader"; + reg = <0x0 0x80000>; + read-only; + }; + + partition@80000 { + label = "config"; + reg = <0x80000 0x80000>; + read-only; + }; + + factory: partition@100000 { + label = "factory"; + reg = <0x100000 0x80000>; + read-only; + }; + + partition@180000 { + label = "config2"; + reg = <0x180000 0x40000>; + read-only; + }; + + partition@1c0000 { + label = "kernel"; + reg = <0x1c0000 0x800000>; + }; + + fwconcat0: partition@9c0000 { + label = "fwconcat0"; + reg = <0x9c0000 0x2000000>; + }; + + partition@29c0000 { + label = "kernel2"; + reg = <0x29c0000 0x800000>; + read-only; + }; + + fwconcat1: partition@31c0000 { + label = "fwconcat1"; + reg = <0x31c0000 0x2a00000>; + }; + + partition@5bc0000 { + label = "private"; + reg = <0x5bc0000 0x1400000>; + read-only; + }; + + partition@6fc0000 { + label = "mydlink"; + reg = <0x6fc0000 0x600000>; + read-only; + }; + + partition@75c0000 { + label = "myconfig"; + reg = <0x75c0000 0xa00000>; + read-only; + }; + }; +}; + +&pcie { + status = "okay"; +}; + +&pcie1 { + wifi@0,0 { + compatible = "mediatek,mt76"; + reg = <0x0000 0 0 0 0>; + mediatek,mtd-eeprom = <&factory 0x0>; + mediatek,disable-radar-background; + }; +}; + +&gmac1 { + status = "okay"; + phy-handle = <ðphy4>; +}; + +&mdio { + ethphy4: ethernet-phy@4 { + reg = <4>; + }; +}; + +&switch0 { + ports { + port@0 { + status = "okay"; + label = "internet"; + }; + + port@2 { + status = "okay"; + label = "ethernet"; + }; + }; +}; diff --git a/target/linux/ramips/image/mt7621.mk b/target/linux/ramips/image/mt7621.mk index 3dd6574bf1..72e0565c42 100644 --- a/target/linux/ramips/image/mt7621.mk +++ b/target/linux/ramips/image/mt7621.mk @@ -9,6 +9,14 @@ DEFAULT_SOC := mt7621 DEVICE_VARS += ELECOM_HWNAME LINKSYS_HWNAME DLINK_HWID +define Build/append-dlink-covr-metadata + echo -ne '{"supported_devices": "$(1)", "firmware": "' > $@metadata.tmp + $(MKHASH) md5 "$@" | head -c32 >> $@metadata.tmp + echo '"}' >> $@metadata.tmp + fwtool -I $@metadata.tmp $@ + rm $@metadata.tmp +endef + define Build/arcadyan-trx echo -ne "hsqs" > $@.hsqs $(eval trx_magic=$(word 1,$(1))) @@ -641,6 +649,31 @@ define Device/cudy_x6-v2 endef TARGET_DEVICES += cudy_x6-v2 +define Device/dlink_covr-x1860-a1 + $(Device/dsa-migration) + BLOCKSIZE := 128k + PAGESIZE := 2048 + KERNEL_SIZE := 8192k + IMAGE_SIZE := 40960k + DEVICE_VENDOR := D-Link + DEVICE_MODEL := COVR-X1860 + DEVICE_VARIANT := A1 + DEVICE_PACKAGES := kmod-mt7915-firmware + UBINIZE_OPTS := -E 5 + KERNEL_LOADADDR := 0x82000000 + KERNEL := kernel-bin | relocate-kernel 0x80001000 | lzma | \ + fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb | \ + append-squashfs4-fakeroot + IMAGES += factory.bin recovery.bin + IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata + IMAGE/recovery.bin := append-kernel | pad-to $$(KERNEL_SIZE) | \ + append-ubi | check-size + IMAGE/factory.bin := $$(IMAGE/recovery.bin) | \ + append-dlink-covr-metadata $$(DEVICE_MODEL) | \ + dlink-sge-image $$(DEVICE_MODEL) +endef +TARGET_DEVICES += dlink_covr-x1860-a1 + define Device/dlink_dxx-1xx0-x1 DEVICE_VENDOR := D-Link DEVICE_PACKAGES := kmod-mt7615-firmware rssileds diff --git a/target/linux/ramips/mt7621/base-files/etc/board.d/02_network b/target/linux/ramips/mt7621/base-files/etc/board.d/02_network index e7f72106dd..ae29da4adc 100644 --- a/target/linux/ramips/mt7621/base-files/etc/board.d/02_network +++ b/target/linux/ramips/mt7621/base-files/etc/board.d/02_network @@ -98,6 +98,9 @@ ramips_setup_interfaces() zyxel,nr7101) ucidef_set_interfaces_lan_wan "lan" "wan" ;; + dlink,covr-x1860-a1) + ucidef_set_interfaces_lan_wan "ethernet" "internet" + ;; gnubee,gb-pc1) ucidef_set_interface_lan "ethblack ethblue" ;; @@ -219,6 +222,11 @@ ramips_setup_macs() label_mac=$lan_mac wan_mac=$(macaddr_add "$lan_mac" 1) ;; + dlink,covr-x1860-a1) + label_mac=$(mtd_get_mac_ascii config2 factory_mac) + wan_mac=$(macaddr_add "$label_mac" 3) + lan_mac=$label_mac + ;; dlink,dir-860l-b1) lan_mac=$(mtd_get_mac_ascii factory lanmac) wan_mac=$(mtd_get_mac_ascii factory wanmac) diff --git a/target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac b/target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac index 96b49ff00a..b6cf9052df 100644 --- a/target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac +++ b/target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac @@ -46,6 +46,13 @@ case "$board" in [ "$PHYNBR" = "1" ] && \ macaddr_add $lan_mac_addr 2 > /sys${DEVPATH}/macaddress ;; + dlink,covr-x1860-a1) + label_mac=$(mtd_get_mac_ascii config2 factory_mac) + [ "$PHYNBR" = "0" ] && \ + macaddr_add $label_mac 1 > /sys${DEVPATH}/macaddress + [ "$PHYNBR" = "1" ] && \ + macaddr_add $label_mac 2 > /sys${DEVPATH}/macaddress + ;; dlink,dap-x1860-a1) hw_mac_addr="$(mtd_get_mac_binary factory 0x4)" [ "$PHYNBR" = "0" ] && \ diff --git a/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh b/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh index 777c87bed8..2b789342ab 100755 --- a/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh +++ b/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh @@ -63,6 +63,7 @@ platform_do_upgrade() { beeline,smartbox-turbo|\ beeline,smartbox-turbo-plus|\ belkin,rt1800|\ + dlink,covr-x1860-a1|\ dlink,dap-x1860-a1|\ dlink,dir-1960-a1|\ dlink,dir-2640-a1|\ -- 2.30.2