From 07c45c085908dc1ba8d6efe24de754504865dcd9 Mon Sep 17 00:00:00 2001 From: =?utf8?q?Antti=20Nyk=C3=A4nen?= Date: Thu, 25 May 2023 09:42:09 +0300 Subject: [PATCH] ipq807x: add support for Compex WPQ873 MIME-Version: 1.0 Content-Type: text/plain; charset=utf8 Content-Transfer-Encoding: 8bit The Compex WPQ873 is a development board with two M.2 B-key slots for cellular modems. Device info: - IPQ8072A SoC - 512MiB RAM - 256MiB NAND flash - 8MiB SPI NOR - 3x 1GigE ports - 1x 2.5GigE port - 2.4GHz/5GHz AX WLAN - 1x USB 3.0 port - 1x M.2 B-key socket with PCIe 3.0 - 1x M.2 B-key socket with PCIe 2.0 and USB 3.0 - 4x SIM card slots - Bluetooth LE 5.0 (QCA4024) Prerequisites 1) TFTP server 2) 3.3V USB to TTL cable for UART console 2.54mm pitch 4-pin header for UART is readily provided on board, no modifications are necessary to access it TTL connector pinout: 2=TX, 3=RX, 4=GND Arrow marks pin 1 which is 3.3V Serial port settings: 115200 8N1 no flow control The device will most likely ship with a QSDK-based firmware. 1. Power on device and interrupt u-boot to obtain u-boot CLI 2. set serverip to IP address of the TFTP server, for example: `setenv serverip 192.168.1.10` 3. Download image from TFTP server: `tftpboot 0x44000000 openwrt-ipq807x-generic-compex_wpq873-squashfs-factory.ubi` 4. Flash ubi image to both partitions and reset: `sf probe imxtract 0x44000000 ubi nand device 0 nand erase 0x0 0x3400000 nand erase 0x3c00000 0x3400000 nand write $fileaddr 0x0 $filesize nand write $fileaddr 0x3c00000 $filesize reset` Afterwards, you can use sysupgrade to flash new OpenWRT images. Signed-off-by: Antti Nykänen --- package/boot/uboot-envtools/files/ipq807x | 1 + .../ipq807x/base-files/etc/board.d/02_network | 1 + .../etc/hotplug.d/firmware/11-ath11k-caldata | 1 + .../base-files/lib/upgrade/platform.sh | 1 + .../arm64/boot/dts/qcom/ipq8072-wpq873.dts | 487 ++++++++++++++++++ target/linux/ipq807x/image/generic.mk | 13 + 6 files changed, 504 insertions(+) create mode 100644 target/linux/ipq807x/files/arch/arm64/boot/dts/qcom/ipq8072-wpq873.dts diff --git a/package/boot/uboot-envtools/files/ipq807x b/package/boot/uboot-envtools/files/ipq807x index ca331f1032..0185c2c8e6 100644 --- a/package/boot/uboot-envtools/files/ipq807x +++ b/package/boot/uboot-envtools/files/ipq807x @@ -14,6 +14,7 @@ netgear,wax218) [ -n "$idx" ] && \ ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x40000" "0x20000" "2" ;; +compex,wpq873|\ edgecore,eap102|\ zyxel,nbg7815) idx="$(find_mtd_index 0:appsblenv)" diff --git a/target/linux/ipq807x/base-files/etc/board.d/02_network b/target/linux/ipq807x/base-files/etc/board.d/02_network index 1da5c3ae1e..edd1e131b6 100644 --- a/target/linux/ipq807x/base-files/etc/board.d/02_network +++ b/target/linux/ipq807x/base-files/etc/board.d/02_network @@ -28,6 +28,7 @@ ipq807x_setup_interfaces() qnap,301w) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 10g-2" "10g-1" ;; + compex,wpq873|\ redmi,ax6|\ xiaomi,ax3600) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" "wan" diff --git a/target/linux/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata b/target/linux/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata index b3564fe9c6..ddb0737d20 100644 --- a/target/linux/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata +++ b/target/linux/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata @@ -10,6 +10,7 @@ case "$FIRMWARE" in "ath11k/IPQ8074/hw2.0/cal-ahb-c000000.wifi.bin") case "$board" in buffalo,wxr-5950ax12|\ + compex,wpq873|\ edgecore,eap102|\ edimax,cax1800|\ dynalink,dl-wrx36|\ diff --git a/target/linux/ipq807x/base-files/lib/upgrade/platform.sh b/target/linux/ipq807x/base-files/lib/upgrade/platform.sh index 11717d6324..f7c4772315 100644 --- a/target/linux/ipq807x/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq807x/base-files/lib/upgrade/platform.sh @@ -66,6 +66,7 @@ platform_do_upgrade() { fw_setenv upgrade_available 1 nand_do_upgrade "$1" ;; + compex,wpq873|\ edimax,cax1800|\ netgear,wax218) nand_do_upgrade "$1" diff --git a/target/linux/ipq807x/files/arch/arm64/boot/dts/qcom/ipq8072-wpq873.dts b/target/linux/ipq807x/files/arch/arm64/boot/dts/qcom/ipq8072-wpq873.dts new file mode 100644 index 0000000000..9779070725 --- /dev/null +++ b/target/linux/ipq807x/files/arch/arm64/boot/dts/qcom/ipq8072-wpq873.dts @@ -0,0 +1,487 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/* Copyright 2023 Nokia */ + +/dts-v1/; + +#include "ipq8074.dtsi" +#include "ipq8074-hk-cpu.dtsi" +#include "ipq8074-ess.dtsi" +#include +#include +#include + +/ { + model = "Compex WPQ873"; + compatible = "compex,wpq873", "qcom,ipq8074"; + + aliases { + serial0 = &blsp1_uart5; + led-boot = &led_power_blue; + led-failsafe = &led_power_red; + led-running = &led_system_green; + led-upgrade = &led_system_blue; + /* Aliases as required by u-boot to patch MAC addresses */ + ethernet0 = &dp6; + ethernet1 = &dp2; + ethernet2 = &dp3; + ethernet3 = &dp4; + label-mac-device = &dp6; + }; + + chosen { + stdout-path = "serial0:115200n8"; + bootargs-append = " root=/dev/ubiblock0_1"; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&tlmm 21 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_power_red: power-red { + label = "red:power"; + gpios = <&tlmm 42 GPIO_ACTIVE_HIGH>; + color = ; + }; + + led_power_blue: power-blue { + label = "blue:power"; + gpios = <&tlmm 43 GPIO_ACTIVE_HIGH>; + color = ; + }; + + led_system_red: system-red { + label = "red:system"; + gpios = <&tlmm 28 GPIO_ACTIVE_HIGH>; + color = ; + }; + + led_system_green: system-green { + label = "green:system"; + gpios = <&tlmm 18 GPIO_ACTIVE_HIGH>; + color = ; + }; + + led_system_blue: system-blue { + label = "blue:system"; + gpios = <&tlmm 19 GPIO_ACTIVE_HIGH>; + color = ; + }; + }; +}; + +&tlmm { + mdio_pins: mdio-pins { + mdc { + pins = "gpio68"; + function = "mdc"; + drive-strength = <8>; + bias-pull-up; + }; + + mdio { + pins = "gpio69"; + function = "mdio"; + drive-strength = <8>; + bias-pull-up; + }; + }; + + i2c_pins: i2c-pins { + pins = "gpio0", "gpio2"; + function = "blsp5_i2c"; + drive-strength = <8>; + bias-disable; + }; +}; + +&blsp1_uart5 { + status = "okay"; +}; + +&blsp1_i2c6 { + status = "okay"; + + pinctrl-0 = <&i2c_pins>; + pinctrl-names = "default"; +}; + +&prng { + status = "okay"; +}; + +&cryptobam { + status = "okay"; +}; + +&crypto { + status = "okay"; +}; + +&qpic_bam { + status = "okay"; +}; + +&blsp1_spi1 { + status = "okay"; +}; + +&tlmm { + mdio_pins: mdio-pins { + mdc { + pins = "gpio68"; + function = "mdc"; + drive-strength = <8>; + bias-pull-up; + }; + + mdio { + pins = "gpio69"; + function = "mdio"; + drive-strength = <8>; + bias-pull-up; + }; + }; + + button_pins: button_pins { + reset_button { + pins = "gpio66"; + function = "gpio"; + drive-strength = <8>; + bias-pull-up; + }; + }; +}; + +&blsp1_spi1 { + status = "okay"; + + flash@0 { + #address-cells = <1>; + #size-cells = <1>; + reg = <0>; + compatible = "jedec,spi-nor"; + spi-max-frequency = <50000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "0:sbl1"; + reg = <0x0 0x50000>; + read-only; + }; + + partition@50000 { + label = "0:mibib"; + reg = <0x50000 0x10000>; + read-only; + }; + + partition@60000 { + label = "0:bootconfig"; + reg = <0x60000 0x20000>; + read-only; + }; + + partition@80000 { + label = "0:bootconfig1"; + reg = <0x80000 0x20000>; + read-only; + }; + + partition@a0000 { + label = "0:qsee"; + reg = <0xa0000 0x180000>; + read-only; + }; + + partition@220000 { + label = "0:qsee_1"; + reg = <0x220000 0x180000>; + read-only; + }; + + partition@3a0000 { + label = "0:devcfg"; + reg = <0x3a0000 0x10000>; + read-only; + }; + + partition@3b0000 { + label = "0:devcfg_1"; + reg = <0x3b0000 0x10000>; + read-only; + }; + + partition@3c0000 { + label = "0:apdp"; + reg = <0x3c0000 0x10000>; + read-only; + }; + + partition@3d0000 { + label = "0:apdp_1"; + reg = <0x3d0000 0x10000>; + read-only; + }; + + partition@3e0000 { + label = "0:rpm"; + reg = <0x3e0000 0x40000>; + read-only; + }; + + partition@420000 { + label = "0:rpm_1"; + reg = <0x420000 0x40000>; + read-only; + }; + + partition@460000 { + label = "0:cdt"; + reg = <0x460000 0x10000>; + read-only; + }; + + partition@470000 { + label = "0:cdt_1"; + reg = <0x470000 0x10000>; + read-only; + }; + + partition@480000 { + label = "0:appsblenv"; + reg = <0x480000 0x10000>; + }; + + partition@490000 { + label = "0:appsbl"; + reg = <0x490000 0xa0000>; + read-only; + }; + + partition@550000 { + label = "0:appsbl_1"; + reg = <0x530000 0xa0000>; + read-only; + }; + + partition@610000 { + label = "0:art"; + reg = <0x5d0000 0x40000>; + read-only; + }; + + partition@650000 { + label = "0:ethphyfw"; + reg = <0x610000 0x80000>; + read-only; + }; + }; + }; +}; + +&qpic_nand { + status = "okay"; + + nand@0 { + reg = <0>; + nand-ecc-strength = <8>; + nand-ecc-step-size = <512>; + nand-bus-width = <8>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "rootfs"; + reg = <0x0000000 0x3400000>; + }; + + partition@3400000 { + label = "0:wififw"; + reg = <0x3400000 0x800000>; + read-only; + }; + + partition@3c00000 { + label = "rootfs_1"; + reg = <0x3c00000 0x3400000>; + }; + + partition@7000000 { + label = "0:wififw_1"; + reg = <0x7000000 0x800000>; + read-only; + }; + }; + }; +}; + +&qusb_phy_0 { + status = "okay"; +}; + +&qusb_phy_1 { + status = "okay"; +}; + +&ssphy_0 { + status = "okay"; +}; + +&ssphy_1 { + status = "okay"; +}; + +&usb_0 { + status = "okay"; +}; + +&usb_1 { + status = "okay"; +}; + + +&mdio { + status = "okay"; + pinctrl-0 = <&mdio_pins>; + pinctrl-names = "default"; + reset-gpios = <&tlmm 37 GPIO_ACTIVE_LOW>; + + qca8075_1: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; + + qca8075_2: ethernet-phy@2 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <2>; + }; + + qca8075_3: ethernet-phy@3 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <3>; + }; + + qca8081: ethernet-phy@28 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <28>; + reset-gpios = <&tlmm 44 GPIO_ACTIVE_LOW>; + }; + +}; + +&switch { + status = "okay"; + + switch_cpu_bmp = <0x1>; /* cpu port bitmap */ + switch_lan_bmp = <0x3e>; /* lan port bitmap */ + switch_wan_bmp = <0x40>; /* wan port bitmap */ + switch_mac_mode = <0x0>; /* mac mode for uniphy instance0*/ + switch_mac_mode1 = <0x0f>; /* mac mode for uniphy instance1*/ + switch_mac_mode2 = <0x0f>; /* mac mode for uniphy instance2*/ + bm_tick_mode = <0>; /* bm tick mode */ + tm_tick_mode = <0>; /* tm tick mode */ + + qcom,port_phyinfo { + port@2 { + port_id = <2>; + phy_address = <1>; + }; + port@3 { + port_id = <3>; + phy_address = <2>; + }; + port@4 { + port_id = <4>; + phy_address = <3>; + }; + port@5 { + port_id = <6>; + phy_address = <28>; + port_mac_sel = "QGMAC_PORT"; + }; + }; +}; + +&edma { + status = "okay"; +}; + +&dp2 { + status = "okay"; + phy-handle = <&qca8075_1>; + label = "lan1"; +}; + +&dp3 { + status = "okay"; + phy-handle = <&qca8075_2>; + label = "lan2"; +}; + +&dp4 { + status = "okay"; + phy-handle = <&qca8075_3>; + label = "lan3"; +}; + +&dp6 { + status = "okay"; + phy-handle = <&qca8081>; + label = "wan"; +}; + +&pcie_qmp0 { + status = "okay"; +}; + +&pcie0 { + status = "okay"; + + perst-gpio = <&tlmm 58 GPIO_ACTIVE_LOW>; + + bridge@0,0 { + reg = <0x00020000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + ranges; + }; +}; + +&pcie_qmp1 { + status = "okay"; +}; + +&pcie1 { + status = "okay"; + + perst-gpio = <&tlmm 62 GPIO_ACTIVE_HIGH>; + + bridge@1,0 { + reg = <0x00010000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + ranges; + }; +}; + +&wifi { + status = "okay"; + + qcom,ath11k-calibration-variant = "Compex-WPQ873"; +}; diff --git a/target/linux/ipq807x/image/generic.mk b/target/linux/ipq807x/image/generic.mk index 609c6690d1..4e80e876d9 100644 --- a/target/linux/ipq807x/image/generic.mk +++ b/target/linux/ipq807x/image/generic.mk @@ -31,6 +31,19 @@ define Device/buffalo_wxr-5950ax12 endef TARGET_DEVICES += buffalo_wxr-5950ax12 +define Device/compex_wpq873 + $(call Device/FitImage) + $(call Device/UbiFit) + DEVICE_VENDOR := Compex + DEVICE_MODEL := WPQ873 + BLOCKSIZE := 128k + PAGESIZE := 2048 + DEVICE_DTS_CONFIG := config@hk09.wpq873 + SOC := ipq8072 + IMAGE/factory.ubi := append-ubi | qsdk-ipq-factory-nand +endef +TARGET_DEVICES += compex_wpq873 + define Device/dynalink_dl-wrx36 $(call Device/FitImage) $(call Device/UbiFit) -- 2.30.2