From 041441d0f0d885619d48f8f7682825ace523cf59 Mon Sep 17 00:00:00 2001 From: Alexander Duyck Date: Thu, 19 Apr 2012 17:48:48 +0000 Subject: [PATCH] ixgbe: Update link flow control to correctly handle multiple packet buffer DCB This change updates the link flow control configuration so that we correctly set the link flow control settings for DCB. Previously we would have to call the fc_enable call 8 times, once for each packet buffer. If we move that logic into the fc_enable call itself we can avoid multiple unnecessary register writes. This change also corrects an issue in which we were only shifting the water marks for 82599 parts by 6 instead of 10. This was resulting in us only using 1/16 of the packet buffer when flow control was enabled. Signed-off-by: Alexander Duyck Tested-by: Ross Brattain Signed-off-by: Jeff Kirsher --- .../net/ethernet/intel/ixgbe/ixgbe_82598.c | 61 +++---- .../net/ethernet/intel/ixgbe/ixgbe_common.c | 164 +++++++----------- .../net/ethernet/intel/ixgbe/ixgbe_common.h | 2 +- .../ethernet/intel/ixgbe/ixgbe_dcb_82599.c | 13 +- drivers/net/ethernet/intel/ixgbe/ixgbe_main.c | 16 +- drivers/net/ethernet/intel/ixgbe/ixgbe_type.h | 4 +- 6 files changed, 102 insertions(+), 158 deletions(-) diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_82598.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_82598.c index badcf821d89a..42537336110c 100644 --- a/drivers/net/ethernet/intel/ixgbe/ixgbe_82598.c +++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_82598.c @@ -324,24 +324,33 @@ out: /** * ixgbe_fc_enable_82598 - Enable flow control * @hw: pointer to hardware structure - * @packetbuf_num: packet buffer number (0-7) * * Enable flow control according to the current settings. **/ -static s32 ixgbe_fc_enable_82598(struct ixgbe_hw *hw, s32 packetbuf_num) +static s32 ixgbe_fc_enable_82598(struct ixgbe_hw *hw) { s32 ret_val = 0; u32 fctrl_reg; u32 rmcs_reg; u32 reg; + u32 fcrtl, fcrth; u32 link_speed = 0; + int i; bool link_up; -#ifdef CONFIG_DCB - if (hw->fc.requested_mode == ixgbe_fc_pfc) + /* + * Validate the water mark configuration for packet buffer 0. Zero + * water marks indicate that the packet buffer was not configured + * and the watermarks for packet buffer 0 should always be configured. + */ + if (!hw->fc.low_water || + !hw->fc.high_water[0] || + !hw->fc.pause_time) { + hw_dbg(hw, "Invalid water mark configuration\n"); + ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS; goto out; + } -#endif /* CONFIG_DCB */ /* * On 82598 having Rx FC on causes resets while doing 1G * so if it's on turn it off once we know link_speed. For @@ -380,9 +389,6 @@ static s32 ixgbe_fc_enable_82598(struct ixgbe_hw *hw, s32 packetbuf_num) * 2: Tx flow control is enabled (we can send pause frames but * we do not support receiving pause frames). * 3: Both Rx and Tx flow control (symmetric) are enabled. -#ifdef CONFIG_DCB - * 4: Priority Flow Control is enabled. -#endif * other: Invalid. */ switch (hw->fc.current_mode) { @@ -415,11 +421,6 @@ static s32 ixgbe_fc_enable_82598(struct ixgbe_hw *hw, s32 packetbuf_num) fctrl_reg |= IXGBE_FCTRL_RFCE; rmcs_reg |= IXGBE_RMCS_TFCE_802_3X; break; -#ifdef CONFIG_DCB - case ixgbe_fc_pfc: - goto out; - break; -#endif /* CONFIG_DCB */ default: hw_dbg(hw, "Flow control param set incorrectly\n"); ret_val = IXGBE_ERR_CONFIG; @@ -432,29 +433,29 @@ static s32 ixgbe_fc_enable_82598(struct ixgbe_hw *hw, s32 packetbuf_num) IXGBE_WRITE_REG(hw, IXGBE_FCTRL, fctrl_reg); IXGBE_WRITE_REG(hw, IXGBE_RMCS, rmcs_reg); - /* Set up and enable Rx high/low water mark thresholds, enable XON. */ - if (hw->fc.current_mode & ixgbe_fc_tx_pause) { - reg = hw->fc.low_water << 6; - if (hw->fc.send_xon) - reg |= IXGBE_FCRTL_XONE; + fcrtl = (hw->fc.low_water << 10) | IXGBE_FCRTL_XONE; - IXGBE_WRITE_REG(hw, IXGBE_FCRTL(packetbuf_num), reg); - - reg = hw->fc.high_water[packetbuf_num] << 6; - reg |= IXGBE_FCRTH_FCEN; + /* Set up and enable Rx high/low water mark thresholds, enable XON. */ + for (i = 0; i < MAX_TRAFFIC_CLASS; i++) { + if ((hw->fc.current_mode & ixgbe_fc_tx_pause) && + hw->fc.high_water[i]) { + fcrth = (hw->fc.high_water[i] << 10) | IXGBE_FCRTH_FCEN; + IXGBE_WRITE_REG(hw, IXGBE_FCRTL(i), fcrtl); + IXGBE_WRITE_REG(hw, IXGBE_FCRTH(i), fcrth); + } else { + IXGBE_WRITE_REG(hw, IXGBE_FCRTL(i), 0); + IXGBE_WRITE_REG(hw, IXGBE_FCRTH(i), 0); + } - IXGBE_WRITE_REG(hw, IXGBE_FCRTH(packetbuf_num), reg); } /* Configure pause time (2 TCs per register) */ - reg = IXGBE_READ_REG(hw, IXGBE_FCTTV(packetbuf_num / 2)); - if ((packetbuf_num & 1) == 0) - reg = (reg & 0xFFFF0000) | hw->fc.pause_time; - else - reg = (reg & 0x0000FFFF) | (hw->fc.pause_time << 16); - IXGBE_WRITE_REG(hw, IXGBE_FCTTV(packetbuf_num / 2), reg); + reg = hw->fc.pause_time * 0x00010001; + for (i = 0; i < (MAX_TRAFFIC_CLASS / 2); i++) + IXGBE_WRITE_REG(hw, IXGBE_FCTTV(i), reg); - IXGBE_WRITE_REG(hw, IXGBE_FCRTV, (hw->fc.pause_time >> 1)); + /* Configure flow control refresh threshold value */ + IXGBE_WRITE_REG(hw, IXGBE_FCRTV, hw->fc.pause_time / 2); out: return ret_val; diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c index 3035f1938f5b..c7e51b85b8b6 100644 --- a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c +++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c @@ -84,39 +84,12 @@ static s32 ixgbe_device_supports_autoneg_fc(struct ixgbe_hw *hw) * * Called at init time to set up flow control. **/ -static s32 ixgbe_setup_fc(struct ixgbe_hw *hw, s32 packetbuf_num) +static s32 ixgbe_setup_fc(struct ixgbe_hw *hw) { s32 ret_val = 0; u32 reg = 0, reg_bp = 0; u16 reg_cu = 0; -#ifdef CONFIG_DCB - if (hw->fc.requested_mode == ixgbe_fc_pfc) { - hw->fc.current_mode = hw->fc.requested_mode; - goto out; - } - -#endif /* CONFIG_DCB */ - /* Validate the packetbuf configuration */ - if (packetbuf_num < 0 || packetbuf_num > 7) { - hw_dbg(hw, "Invalid packet buffer number [%d], expected range is 0-7\n", - packetbuf_num); - ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS; - goto out; - } - - /* - * Validate the water mark configuration. Zero water marks are invalid - * because it causes the controller to just blast out fc packets. - */ - if (!hw->fc.low_water || - !hw->fc.high_water[packetbuf_num] || - !hw->fc.pause_time) { - hw_dbg(hw, "Invalid water mark configuration\n"); - ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS; - goto out; - } - /* * Validate the requested mode. Strict IEEE mode does not allow * ixgbe_fc_rx_pause because it will cause us to fail at UNH. @@ -139,21 +112,18 @@ static s32 ixgbe_setup_fc(struct ixgbe_hw *hw, s32 packetbuf_num) * HW will be able to do fc autoneg once the cable is plugged in. If * we link at 10G, the 1G advertisement is harmless and vice versa. */ - switch (hw->phy.media_type) { case ixgbe_media_type_fiber: case ixgbe_media_type_backplane: reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA); reg_bp = IXGBE_READ_REG(hw, IXGBE_AUTOC); break; - case ixgbe_media_type_copper: hw->phy.ops.read_reg(hw, MDIO_AN_ADVERTISE, MDIO_MMD_AN, ®_cu); break; - default: - ; + break; } /* @@ -164,9 +134,6 @@ static s32 ixgbe_setup_fc(struct ixgbe_hw *hw, s32 packetbuf_num) * 2: Tx flow control is enabled (we can send pause frames but * we do not support receiving pause frames). * 3: Both Rx and Tx flow control (symmetric) are enabled. -#ifdef CONFIG_DCB - * 4: Priority Flow Control is enabled. -#endif * other: Invalid. */ switch (hw->fc.requested_mode) { @@ -179,51 +146,40 @@ static s32 ixgbe_setup_fc(struct ixgbe_hw *hw, s32 packetbuf_num) else if (hw->phy.media_type == ixgbe_media_type_copper) reg_cu &= ~(IXGBE_TAF_SYM_PAUSE | IXGBE_TAF_ASM_PAUSE); break; - case ixgbe_fc_rx_pause: - /* - * Rx Flow control is enabled and Tx Flow control is - * disabled by software override. Since there really - * isn't a way to advertise that we are capable of RX - * Pause ONLY, we will advertise that we support both - * symmetric and asymmetric Rx PAUSE. Later, we will - * disable the adapter's ability to send PAUSE frames. - */ - reg |= (IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE); - if (hw->phy.media_type == ixgbe_media_type_backplane) - reg_bp |= (IXGBE_AUTOC_SYM_PAUSE | - IXGBE_AUTOC_ASM_PAUSE); - else if (hw->phy.media_type == ixgbe_media_type_copper) - reg_cu |= (IXGBE_TAF_SYM_PAUSE | IXGBE_TAF_ASM_PAUSE); - break; case ixgbe_fc_tx_pause: /* * Tx Flow control is enabled, and Rx Flow control is * disabled by software override. */ - reg |= (IXGBE_PCS1GANA_ASM_PAUSE); - reg &= ~(IXGBE_PCS1GANA_SYM_PAUSE); + reg |= IXGBE_PCS1GANA_ASM_PAUSE; + reg &= ~IXGBE_PCS1GANA_SYM_PAUSE; if (hw->phy.media_type == ixgbe_media_type_backplane) { - reg_bp |= (IXGBE_AUTOC_ASM_PAUSE); - reg_bp &= ~(IXGBE_AUTOC_SYM_PAUSE); + reg_bp |= IXGBE_AUTOC_ASM_PAUSE; + reg_bp &= ~IXGBE_AUTOC_SYM_PAUSE; } else if (hw->phy.media_type == ixgbe_media_type_copper) { - reg_cu |= (IXGBE_TAF_ASM_PAUSE); - reg_cu &= ~(IXGBE_TAF_SYM_PAUSE); + reg_cu |= IXGBE_TAF_ASM_PAUSE; + reg_cu &= ~IXGBE_TAF_SYM_PAUSE; } break; + case ixgbe_fc_rx_pause: + /* + * Rx Flow control is enabled and Tx Flow control is + * disabled by software override. Since there really + * isn't a way to advertise that we are capable of RX + * Pause ONLY, we will advertise that we support both + * symmetric and asymmetric Rx PAUSE, as such we fall + * through to the fc_full statement. Later, we will + * disable the adapter's ability to send PAUSE frames. + */ case ixgbe_fc_full: /* Flow control (both Rx and Tx) is enabled by SW override. */ - reg |= (IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE); + reg |= IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE; if (hw->phy.media_type == ixgbe_media_type_backplane) - reg_bp |= (IXGBE_AUTOC_SYM_PAUSE | - IXGBE_AUTOC_ASM_PAUSE); + reg_bp |= IXGBE_AUTOC_SYM_PAUSE | + IXGBE_AUTOC_ASM_PAUSE; else if (hw->phy.media_type == ixgbe_media_type_copper) - reg_cu |= (IXGBE_TAF_SYM_PAUSE | IXGBE_TAF_ASM_PAUSE); - break; -#ifdef CONFIG_DCB - case ixgbe_fc_pfc: - goto out; + reg_cu |= IXGBE_TAF_SYM_PAUSE | IXGBE_TAF_ASM_PAUSE; break; -#endif /* CONFIG_DCB */ default: hw_dbg(hw, "Flow control param set incorrectly\n"); ret_val = IXGBE_ERR_CONFIG; @@ -298,7 +254,7 @@ s32 ixgbe_start_hw_generic(struct ixgbe_hw *hw) IXGBE_WRITE_FLUSH(hw); /* Setup flow control */ - ixgbe_setup_fc(hw, 0); + ixgbe_setup_fc(hw); /* Clear adapter stopped flag */ hw->adapter_stopped = false; @@ -2126,28 +2082,36 @@ s32 ixgbe_disable_mc_generic(struct ixgbe_hw *hw) /** * ixgbe_fc_enable_generic - Enable flow control * @hw: pointer to hardware structure - * @packetbuf_num: packet buffer number (0-7) * * Enable flow control according to the current settings. **/ -s32 ixgbe_fc_enable_generic(struct ixgbe_hw *hw, s32 packetbuf_num) +s32 ixgbe_fc_enable_generic(struct ixgbe_hw *hw) { s32 ret_val = 0; u32 mflcn_reg, fccfg_reg; u32 reg; u32 fcrtl, fcrth; + int i; -#ifdef CONFIG_DCB - if (hw->fc.requested_mode == ixgbe_fc_pfc) + /* + * Validate the water mark configuration for packet buffer 0. Zero + * water marks indicate that the packet buffer was not configured + * and the watermarks for packet buffer 0 should always be configured. + */ + if (!hw->fc.low_water || + !hw->fc.high_water[0] || + !hw->fc.pause_time) { + hw_dbg(hw, "Invalid water mark configuration\n"); + ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS; goto out; + } -#endif /* CONFIG_DCB */ /* Negotiate the fc mode to use */ ixgbe_fc_autoneg(hw); /* Disable any previous flow control settings */ mflcn_reg = IXGBE_READ_REG(hw, IXGBE_MFLCN); - mflcn_reg &= ~(IXGBE_MFLCN_RFCE | IXGBE_MFLCN_RPFCE); + mflcn_reg &= ~(IXGBE_MFLCN_RPFCE_MASK | IXGBE_MFLCN_RFCE); fccfg_reg = IXGBE_READ_REG(hw, IXGBE_FCCFG); fccfg_reg &= ~(IXGBE_FCCFG_TFCE_802_3X | IXGBE_FCCFG_TFCE_PRIORITY); @@ -2160,9 +2124,6 @@ s32 ixgbe_fc_enable_generic(struct ixgbe_hw *hw, s32 packetbuf_num) * 2: Tx flow control is enabled (we can send pause frames but * we do not support receiving pause frames). * 3: Both Rx and Tx flow control (symmetric) are enabled. -#ifdef CONFIG_DCB - * 4: Priority Flow Control is enabled. -#endif * other: Invalid. */ switch (hw->fc.current_mode) { @@ -2195,11 +2156,6 @@ s32 ixgbe_fc_enable_generic(struct ixgbe_hw *hw, s32 packetbuf_num) mflcn_reg |= IXGBE_MFLCN_RFCE; fccfg_reg |= IXGBE_FCCFG_TFCE_802_3X; break; -#ifdef CONFIG_DCB - case ixgbe_fc_pfc: - goto out; - break; -#endif /* CONFIG_DCB */ default: hw_dbg(hw, "Flow control param set incorrectly\n"); ret_val = IXGBE_ERR_CONFIG; @@ -2212,34 +2168,34 @@ s32 ixgbe_fc_enable_generic(struct ixgbe_hw *hw, s32 packetbuf_num) IXGBE_WRITE_REG(hw, IXGBE_MFLCN, mflcn_reg); IXGBE_WRITE_REG(hw, IXGBE_FCCFG, fccfg_reg); - fcrtl = hw->fc.low_water << 10; + fcrtl = (hw->fc.low_water << 10) | IXGBE_FCRTL_XONE; - if (hw->fc.current_mode & ixgbe_fc_tx_pause) { - fcrth = hw->fc.high_water[packetbuf_num] << 10; - fcrth |= IXGBE_FCRTH_FCEN; - if (hw->fc.send_xon) - fcrtl |= IXGBE_FCRTL_XONE; - } else { - /* - * If Tx flow control is disabled, set our high water mark - * to Rx FIFO size minus 32 in order prevent Tx switch - * loopback from stalling on DMA. - */ - fcrth = IXGBE_READ_REG(hw, IXGBE_RXPBSIZE(packetbuf_num)) - 32; - } + /* Set up and enable Rx high/low water mark thresholds, enable XON. */ + for (i = 0; i < MAX_TRAFFIC_CLASS; i++) { + if ((hw->fc.current_mode & ixgbe_fc_tx_pause) && + hw->fc.high_water[i]) { + IXGBE_WRITE_REG(hw, IXGBE_FCRTL_82599(i), fcrtl); + fcrth = (hw->fc.high_water[i] << 10) | IXGBE_FCRTH_FCEN; + } else { + IXGBE_WRITE_REG(hw, IXGBE_FCRTL_82599(i), 0); + /* + * In order to prevent Tx hangs when the internal Tx + * switch is enabled we must set the high water mark + * to the maximum FCRTH value. This allows the Tx + * switch to function even under heavy Rx workloads. + */ + fcrth = IXGBE_READ_REG(hw, IXGBE_RXPBSIZE(i)) - 32; + } - IXGBE_WRITE_REG(hw, IXGBE_FCRTH_82599(packetbuf_num), fcrth); - IXGBE_WRITE_REG(hw, IXGBE_FCRTL_82599(packetbuf_num), fcrtl); + IXGBE_WRITE_REG(hw, IXGBE_FCRTH_82599(i), fcrth); + } /* Configure pause time (2 TCs per register) */ - reg = IXGBE_READ_REG(hw, IXGBE_FCTTV(packetbuf_num / 2)); - if ((packetbuf_num & 1) == 0) - reg = (reg & 0xFFFF0000) | hw->fc.pause_time; - else - reg = (reg & 0x0000FFFF) | (hw->fc.pause_time << 16); - IXGBE_WRITE_REG(hw, IXGBE_FCTTV(packetbuf_num / 2), reg); + reg = hw->fc.pause_time * 0x00010001; + for (i = 0; i < (MAX_TRAFFIC_CLASS / 2); i++) + IXGBE_WRITE_REG(hw, IXGBE_FCTTV(i), reg); - IXGBE_WRITE_REG(hw, IXGBE_FCRTV, (hw->fc.pause_time >> 1)); + IXGBE_WRITE_REG(hw, IXGBE_FCRTV, hw->fc.pause_time / 2); out: return ret_val; diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.h b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.h index 9e8a1c05df6e..6222fdb3d3f1 100644 --- a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.h +++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.h @@ -77,7 +77,7 @@ s32 ixgbe_disable_mc_generic(struct ixgbe_hw *hw); s32 ixgbe_disable_rx_buff_generic(struct ixgbe_hw *hw); s32 ixgbe_enable_rx_buff_generic(struct ixgbe_hw *hw); s32 ixgbe_enable_rx_dma_generic(struct ixgbe_hw *hw, u32 regval); -s32 ixgbe_fc_enable_generic(struct ixgbe_hw *hw, s32 packetbuf_num); +s32 ixgbe_fc_enable_generic(struct ixgbe_hw *hw); void ixgbe_fc_autoneg(struct ixgbe_hw *hw); s32 ixgbe_validate_mac_addr(u8 *mac_addr); diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_dcb_82599.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_dcb_82599.c index 888a419dc3d9..65913c5a616e 100644 --- a/drivers/net/ethernet/intel/ixgbe/ixgbe_dcb_82599.c +++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_dcb_82599.c @@ -278,18 +278,7 @@ s32 ixgbe_dcb_config_pfc_82599(struct ixgbe_hw *hw, u8 pfc_en, u8 *prio_tc) IXGBE_WRITE_REG(hw, IXGBE_MFLCN, reg); } else { - /* X540 devices have a RX bit that should be cleared - * if PFC is disabled on all TCs but PFC features is - * enabled. - */ - if (hw->mac.type == ixgbe_mac_X540) { - reg = IXGBE_READ_REG(hw, IXGBE_MFLCN); - reg &= ~IXGBE_MFLCN_RPFCE_MASK; - IXGBE_WRITE_REG(hw, IXGBE_MFLCN, reg); - } - - for (i = 0; i < MAX_TRAFFIC_CLASS; i++) - hw->mac.ops.fc_enable(hw, i); + hw->mac.ops.fc_enable(hw); } return 0; diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c index c2ceda9133ba..b2daff3b3328 100644 --- a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c +++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c @@ -5250,7 +5250,7 @@ static void ixgbe_watchdog_update_link(struct ixgbe_adapter *adapter) struct ixgbe_hw *hw = &adapter->hw; u32 link_speed = adapter->link_speed; bool link_up = adapter->link_up; - int i; + bool pfc_en = adapter->dcb_cfg.pfc_mode_enable; if (!(adapter->flags & IXGBE_FLAG_NEED_LINK_UPDATE)) return; @@ -5262,14 +5262,12 @@ static void ixgbe_watchdog_update_link(struct ixgbe_adapter *adapter) link_speed = IXGBE_LINK_SPEED_10GB_FULL; link_up = true; } - if (link_up) { - if (adapter->flags & IXGBE_FLAG_DCB_ENABLED) { - for (i = 0; i < MAX_TRAFFIC_CLASS; i++) - hw->mac.ops.fc_enable(hw, i); - } else { - hw->mac.ops.fc_enable(hw, 0); - } - } + + if (adapter->ixgbe_ieee_pfc) + pfc_en |= !!(adapter->ixgbe_ieee_pfc->pfc_en); + + if (link_up && !((adapter->flags & IXGBE_FLAG_DCB_ENABLED) && pfc_en)) + hw->mac.ops.fc_enable(hw); if (link_up || time_after(jiffies, (adapter->link_check_timeout + diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h b/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h index 5337260bed5b..5e64c77255e9 100644 --- a/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h +++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h @@ -1892,7 +1892,7 @@ enum { #define IXGBE_MFLCN_DPF 0x00000002 /* Discard Pause Frame */ #define IXGBE_MFLCN_RPFCE 0x00000004 /* Receive Priority FC Enable */ #define IXGBE_MFLCN_RFCE 0x00000008 /* Receive FC Enable */ -#define IXGBE_MFLCN_RPFCE_MASK 0x00000FF0 /* Receive FC Mask */ +#define IXGBE_MFLCN_RPFCE_MASK 0x00000FF4 /* Receive FC Mask */ #define IXGBE_MFLCN_RPFCE_SHIFT 4 @@ -2808,7 +2808,7 @@ struct ixgbe_mac_operations { void (*set_vlan_anti_spoofing)(struct ixgbe_hw *, bool, int); /* Flow Control */ - s32 (*fc_enable)(struct ixgbe_hw *, s32); + s32 (*fc_enable)(struct ixgbe_hw *); /* Manageability interface */ s32 (*set_fw_drv_ver)(struct ixgbe_hw *, u8, u8, u8, u8); -- 2.30.2