From 030fc6ab6cc1f4982809b65edf9c874d9117cd1f Mon Sep 17 00:00:00 2001 From: Jackson Lim Date: Thu, 25 Jul 2019 22:44:11 +0800 Subject: [PATCH] ath79: add support for D-Link DIR-842 C1 Hardware spec of DIR-842 C1: SoC: QCA9563 DRAM: 128MB DDR2 Flash: 16MB SPI-NOR Switch: QCA8337N WiFi 5.8GHz: QCA9888 WiFi 2.4Ghz: QCA9563 USB: circuit onboard, but components are not soldered Flash instructions: 1. Upgrade the factory.bin through the factory web interface or the u-boot failsafe interface. The firmware will boot up correctly for the first time. Do not power off the device after OpenWrt has booted. Otherwise the u-boot will enter failsafe mode as the checksum of the firmware has been changed. 2. Upgrade the sysupgrade.bin in OpenWrt. After upgrading completes the u-boot won't complain about the firmware checksum and it's OK to use now. 3. If you powered off the device before upgrading the sysupgrade.bin, just upgrade the factory.bin through the u-boot failsafe interface and then goto step 2. Signed-off-by: Jackson Lim [fix whitespace issues] Signed-off-by: David Bauer --- .../ath79/base-files/etc/board.d/01_leds | 1 + .../ath79/base-files/etc/board.d/02_network | 2 + .../etc/hotplug.d/firmware/10-ath9k-eeprom | 1 + .../etc/hotplug.d/firmware/11-ath10k-caldata | 1 + .../ath79/dts/qca9563_dlink_dir-842-c.dtsi | 145 ++++++++++++++++++ .../ath79/dts/qca9563_dlink_dir-842-c1.dts | 41 +++++ .../ath79/dts/qca9563_dlink_dir-842-c2.dts | 143 +---------------- target/linux/ath79/image/generic.mk | 17 +- 8 files changed, 207 insertions(+), 144 deletions(-) create mode 100644 target/linux/ath79/dts/qca9563_dlink_dir-842-c.dtsi create mode 100644 target/linux/ath79/dts/qca9563_dlink_dir-842-c1.dts diff --git a/target/linux/ath79/base-files/etc/board.d/01_leds b/target/linux/ath79/base-files/etc/board.d/01_leds index 03e28e322a9d..29c32ada7240 100755 --- a/target/linux/ath79/base-files/etc/board.d/01_leds +++ b/target/linux/ath79/base-files/etc/board.d/01_leds @@ -62,6 +62,7 @@ comfast,cf-e5) ucidef_set_led_rssi "rssimedium" "RSSIMEDIUM" "$boardname:blue:rssi1" "wlan0" "33" "100" ucidef_set_led_rssi "rssihigh" "RSSIHIGH" "$boardname:blue:rssi2" "wlan0" "66" "100" ;; +dlink,dir-842-c1|\ dlink,dir-842-c2|\ dlink,dir-859-a1) ucidef_set_led_switch "internet" "WAN" "$boardname:green:internet" "switch0" "0x20" diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network index 9e44981022f5..4338b2955dcf 100755 --- a/target/linux/ath79/base-files/etc/board.d/02_network +++ b/target/linux/ath79/base-files/etc/board.d/02_network @@ -115,6 +115,7 @@ ath79_setup_interfaces() ;; dlink,dir-825-c1|\ dlink,dir-835-a1|\ + dlink,dir-842-c1|\ dlink,dir-842-c2|\ dlink,dir-859-a1|\ engenius,epg5000|\ @@ -307,6 +308,7 @@ ath79_setup_macs() lan_mac=$(mtd_get_mac_text "mac" 4) wan_mac=$(mtd_get_mac_text "mac" 24) ;; + dlink,dir-842-c1|\ dlink,dir-842-c2|\ dlink,dir-859-a1|\ nec,wg1200cr|\ diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom b/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom index 7850c689b861..a7d482580bc3 100644 --- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom +++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom @@ -105,6 +105,7 @@ case "$FIRMWARE" in ath9k_eeprom_extract "art" 4096 1088 ath9k_patch_fw_mac_crc $(mtd_get_mac_text "mac" 4) 2 ;; + dlink,dir-842-c1|\ dlink,dir-842-c2|\ dlink,dir-859-a1|\ nec,wg1200cr|\ diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 41186853efa9..f6e2b801cbe7 100644 --- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -189,6 +189,7 @@ case "$FIRMWARE" in ;; "ath10k/pre-cal-pci-0000:00:00.0.bin") case $board in + dlink,dir-842-c1|\ dlink,dir-842-c2|\ nec,wg1200cr) ath10kcal_extract "art" 20480 12064 diff --git a/target/linux/ath79/dts/qca9563_dlink_dir-842-c.dtsi b/target/linux/ath79/dts/qca9563_dlink_dir-842-c.dtsi new file mode 100644 index 000000000000..ac8fe3ae0a6f --- /dev/null +++ b/target/linux/ath79/dts/qca9563_dlink_dir-842-c.dtsi @@ -0,0 +1,145 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include +#include + +#include "qca956x.dtsi" + +/ { + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + keys { + compatible = "gpio-keys"; + + wps { + linux,code = ; + gpios = <&gpio 1 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + + reset { + linux,code = ; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + }; + + // Pull up on boot - otherwise the reset button won't work + reset-button { + gpio-hog; + output-high; + gpios = <11 GPIO_ACTIVE_LOW>; + line-name = "reset-button"; + }; +}; + +&uart { + status = "okay"; +}; + +&pcie { + status = "okay"; +}; + +&spi { + status = "okay"; + num-cs = <1>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <30000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x000000 0x40000>; + read-only; + }; + + partition@40000 { + label = "u-boot-env"; + reg = <0x040000 0x10000>; + read-only; + }; + + partition@50000 { + label = "devdata"; + reg = <0x050000 0x10000>; + read-only; + }; + + partition@60000 { + label = "devconf"; + reg = <0x060000 0x10000>; + read-only; + }; + + partition@70000 { + label = "misc"; + reg = <0x070000 0x10000>; + read-only; + }; + + partition@80000 { + compatible = "seama"; + label = "firmware"; + reg = <0x080000 0xf50000>; + }; + + art: partition@fd0000 { + label = "art"; + reg = <0xfd0000 0x010000>; + read-only; + }; + + partition@fe0000 { + label = "reserved"; + reg = <0xfe0000 0x20000>; + read-only; + }; + }; + }; +}; + +&mdio0 { + status = "okay"; + + phy-mask = <0>; + + phy0: ethernet-phy@0 { + reg = <0>; + qca,mib-poll-interval = <500>; + + qca,ar8327-initvals = < + 0x04 0x00080080 /* PORT0 PAD MODE CTRL */ + 0x10 0x81000080 /* POWER_ON_STRIP */ + 0x50 0xcc35cc35 /* LED_CTRL0 */ + 0x54 0xcb37cb37 /* LED_CTRL1 */ + 0x58 0x00000000 /* LED_CTRL2 */ + 0x5c 0x00f3cf00 /* LED_CTRL3 */ + 0x7c 0x0000007e /* PORT0_STATUS */ + >; + }; +}; + +ð0 { + status = "okay"; + + pll-data = <0x03000101 0x00000101 0x00001919>; + + phy-mode = "sgmii"; + phy-handle = <&phy0>; +}; + +&wmac { + status = "okay"; + qca,no-eeprom; +}; diff --git a/target/linux/ath79/dts/qca9563_dlink_dir-842-c1.dts b/target/linux/ath79/dts/qca9563_dlink_dir-842-c1.dts new file mode 100644 index 000000000000..971c56792442 --- /dev/null +++ b/target/linux/ath79/dts/qca9563_dlink_dir-842-c1.dts @@ -0,0 +1,41 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include "qca9563_dlink_dir-842-c.dtsi" + +/ { + compatible = "dlink,dir-842-c1", "qca,qca9563"; + model = "D-Link DIR-842 C1"; + + aliases { + led-boot = &power; + led-failsafe = &power; + led-running = &power; + led-upgrade = &power; + }; + + leds { + compatible = "gpio-leds"; + + wps { + label = "dir-842-c1:green:wps"; + gpios = <&gpio 8 GPIO_ACTIVE_LOW>; + }; + + power: power { + label = "dir-842-c1:green:power"; + gpios = <&gpio 15 GPIO_ACTIVE_LOW>; + }; + + internet { + label = "dir-842-c1:green:internet"; + gpios = <&gpio 16 GPIO_ACTIVE_LOW>; + }; + + wlan { + label = "dir-842-c1:green:wlan"; + gpios = <&gpio 19 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + }; +}; diff --git a/target/linux/ath79/dts/qca9563_dlink_dir-842-c2.dts b/target/linux/ath79/dts/qca9563_dlink_dir-842-c2.dts index 49e385526880..9d70dd9be788 100644 --- a/target/linux/ath79/dts/qca9563_dlink_dir-842-c2.dts +++ b/target/linux/ath79/dts/qca9563_dlink_dir-842-c2.dts @@ -1,14 +1,11 @@ // SPDX-License-Identifier: GPL-2.0-or-later OR MIT /dts-v1/; -#include -#include - -#include "qca956x.dtsi" +#include "qca9563_dlink_dir-842-c.dtsi" / { - model = "D-Link DIR-842 C2"; compatible = "dlink,dir-842-c2", "qca,qca9563"; + model = "D-Link DIR-842 C2"; aliases { led-boot = &power; @@ -17,10 +14,6 @@ led-upgrade = &power; }; - chosen { - bootargs = "console=ttyS0,115200n8"; - }; - leds { compatible = "gpio-leds"; @@ -45,138 +38,6 @@ linux,default-trigger = "phy0tpt"; }; }; - - keys { - compatible = "gpio-keys"; - - wps { - linux,code = ; - gpios = <&gpio 1 GPIO_ACTIVE_LOW>; - debounce-interval = <60>; - }; - - reset { - linux,code = ; - gpios = <&gpio 2 GPIO_ACTIVE_LOW>; - debounce-interval = <60>; - }; - }; - - // Pull up on boot - otherwise the reset button won't work - reset-button { - gpio-hog; - output-high; - gpios = <11 GPIO_ACTIVE_LOW>; - line-name = "reset-button"; - }; -}; - -&uart { - status = "okay"; -}; - -&pcie { - status = "okay"; -}; - -&spi { - status = "okay"; - num-cs = <1>; - - flash@0 { - compatible = "jedec,spi-nor"; - reg = <0>; - spi-max-frequency = <30000000>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "u-boot"; - reg = <0x000000 0x40000>; - read-only; - }; - - partition@40000 { - label = "u-boot-env"; - reg = <0x040000 0x10000>; - read-only; - }; - - partition@50000 { - label = "devdata"; - reg = <0x050000 0x10000>; - read-only; - }; - - partition@60000 { - label = "devconf"; - reg = <0x060000 0x10000>; - read-only; - }; - - partition@70000 { - label = "misc"; - reg = <0x070000 0x10000>; - read-only; - }; - - partition@80000 { - compatible = "seama"; - label = "firmware"; - reg = <0x080000 0xf50000>; - }; - - art: partition@fd0000 { - label = "art"; - reg = <0xfd0000 0x010000>; - read-only; - }; - - partition@fe0000 { - label = "reserved"; - reg = <0xfe0000 0x20000>; - read-only; - }; - }; - }; -}; - -&mdio0 { - status = "okay"; - - phy-mask = <0>; - - phy0: ethernet-phy@0 { - reg = <0>; - qca,mib-poll-interval = <500>; - - qca,ar8327-initvals = < - 0x04 0x00080080 /* PORT0 PAD MODE CTRL */ - 0x10 0x81000080 /* POWER_ON_STRIP */ - 0x50 0xcc35cc35 /* LED_CTRL0 */ - 0x54 0xcb37cb37 /* LED_CTRL1 */ - 0x58 0x00000000 /* LED_CTRL2 */ - 0x5c 0x00f3cf00 /* LED_CTRL3 */ - 0x7c 0x0000007e /* PORT0_STATUS */ - >; - }; -}; - -ð0 { - status = "okay"; - - pll-data = <0x03000101 0x00000101 0x00001919>; - - phy-mode = "sgmii"; - phy-handle = <&phy0>; -}; - -&wmac { - status = "okay"; - qca,no-eeprom; }; &usb_phy0 { diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk index 42e4271e0cdf..80095827788b 100644 --- a/target/linux/ath79/image/generic.mk +++ b/target/linux/ath79/image/generic.mk @@ -365,11 +365,10 @@ define Device/dlink_dir-859-a1 endef TARGET_DEVICES += dlink_dir-859-a1 -define Device/dlink_dir-842-c2 +define Device/dlink_dir-842-c ATH_SOC := qca9563 DEVICE_VENDOR := D-Link DEVICE_MODEL := DIR-842 - DEVICE_VARIANT := C2 KERNEL := kernel-bin | append-dtb | relocate-kernel | lzma KERNEL_INITRAMFS := $$(KERNEL) | seama IMAGES += factory.bin @@ -384,7 +383,19 @@ define Device/dlink_dir-842-c2 IMAGE/factory.bin := \ $$(IMAGE/default) | pad-rootfs -x 64 | seama | seama-seal | check-size $$$$(IMAGE_SIZE) IMAGE_SIZE := 15680k - DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca9888-ct +endef + +define Device/dlink_dir-842-c1 + $(Device/dlink_dir-842-c) + DEVICE_VARIANT := C1 + DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct +endef +TARGET_DEVICES += dlink_dir-842-c1 + +define Device/dlink_dir-842-c2 + $(Device/dlink_dir-842-c) + DEVICE_VARIANT := C2 + DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca9888-ct endef TARGET_DEVICES += dlink_dir-842-c2 -- 2.30.2